Search Documents

By J. A. Woolf, E. S. Leaver

"So much has been written on the ore genesis of the Comstock Lode that it is sufficient here to describe the original ores as consisting chiefly of quartz and some calcite. In places .a considerable amount of pyrite appears. There are also minor amounts of galena, chalcopyrite, and sphalerite. The chief silver minerals are argentite, stephanite, and polybasite. Most of the gold is native.A composite analysis of the ore; obtained by averaging the results from the early workings of several mines, is shown in Table 1.The history of the milling of Comstock ores from the Sixties to date would call for a review of the development of precious-metal metallurgy. However, a brief outline of the methods employed will give a better basis for studying the difficulties that are to be expected in the final retreatment of the remaining residues.In the earliest days amalgamation was accepted as the main recovery method. The large tonnage of good-grade ore from the Comstock Lode attracted the best metal¬lurgical talent of the time, and developed there the highest skill in the art of amalgamation, including the auxiliary chemical preparation of the ores and the mechanical operation. In this work 0.5 to 6.0 pounds of mercury was used per ton of ore. The mercury loss probably averaged about 2.5 pounds per ton of ore treated.The better grade of tailings from the ores milled were impounded, often near the works. In many cases the same tailings were reworked several times before they entered the main outflow waste stream that had its course down Seven Mile Canyon to the Carson River. Following the water course down the canyon the tailings were re-impounded, and, as metallurgy advanced, new plants were erected to again re-treat them. The most successful of these plants used forms of amalgamation, chlorination, and cyanide methods of recovery. To the tailings from the re-treatment plants, smaller tonnages of untreated tailings produced by milling lower-grade ore are continually added.Along the stream bed down the canyon a series of blanket runways were constructed, and each was independently operated for years by one or more men. All, or the heavier portion of the stream flow was run over the blankets; in this way much of the heavier concentrate, mostly sulphides and mercury products, was reclaimed.All of the residues finally entered the run-off flow along with the sewage from Virginia City and waste from the gas works, saw mills, and stables. As the accumulation along the bed of the Carson River became a nuisance, the lighter and better grade of tailings was impounded on the banks of the river. This accounts for the large dumps locally known as ""Douglas tailings."""

Jul 1, 1928

To quickly and more reliably measure the alignment and deflection of mine guides used to run skips and cages into a mine shaft. The Problem Conventional mine guide alignment measuring systems require the use of a plumb bob and tape measure. This method is not only laborious, but it is time consuming as well. Approach Aware of the drawbacks of the current measuring method, the Bureau of Mines designed a self-contained instrument system that can accurately perform vertical guide alignment and deflection measurements by remote control. How It Works The Bureau-developed instrumentation system, called the Guide Alignment Measuring System (GAMS), is based on conventional mechanical electronics using inclinometers and displacement transducers. The instrumentation system is attached to an operating skip or cage where it functions as a completely self-contained measurement system, operating in conjunction with nor-mal travel of the skip or cage. An on-board tape recorder or a mini-computer with memory can be used to record all telemetry.

Jan 1, 1987

Develop technology for preparing thick corrosion-resistant coatings and electroforms of iron-chromium-nickel alloys. Approach To reduce the United States' dependence upon foreign sources for supplies of strategic and critical metals such as chromium, cobalt, and nickel, new technology must be devised to conserve these valuable commodities. One approach being investigated by the Bureau of Mines is the use of a modified-aqueous-electrodeposition method to prepare thick (-25 µm), complex alloy coatings (e.g., stainless steel composition) with properties similar to the commercial alloys. An alloy coating on a low-alloy steel or carbon steel substrate would require significantly less strategic and critical metals than those contained in an equivalent mass of the commercial alloy. Coatings applied to appropriate mandrel materials make possible the preparation of intricately-shaped alloy electroforms (near-net-shape parts). As a result, the loss of valuable metals associated with machining finished products would be minimized.

Jan 1, 1986

Provide the mining industry with a wireless surveying system for increasing efficiency in the drilling of methane drainage or exploration boreholes. Approach The Bureau of Mines has pioneered the technique of methane control by drilling long, horizontal drainage holes from within the mine complex. It was recognized during the early drainage projects that a major portion of the drilling operation was dedicated to hole surveying. In some cases more time was actually being spent on the surveying operation than on drilling. The large amount of time required for hole surveying was the result of having to pump an instrument to the bottom of the hole, then retrieve it with an attached wire line. Naturally as hole depth increased, so did the amount of time needed to perform the survey operation. If the survey operation could be improved it was obvious that overall efficiency in drilling of long, horizontal methane drainage holes would be greatly increased. The Bureau of Mines, therefore, developed, fabricated and tested in an operating coal mine a permissible wireless survey system specifically designed for small diameter methane drainage drilling. The prototype survey system was completed in 1982 and was given the IR-100 Award by Industrial Research and Development Magazine. A second generation survey system is currently being constructed using updated state-of-the-art electronic technology. The second generation system will be more portable, more reliable, easier to maintain, and less costly.

Jan 1, 1984

By P. G. Kovalchik

Overexposure to noise remains a widespread, serious health hazard in the US mining and other industries despite 25 years of regulation. Most categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. The drilling of rock in a confined work environment contributes to high levels of noise exposure in mining. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce the noise exposures of jackleg drill operators and to prevent additional cases of noise induced hearing loss (NIHL) by developing and evaluating low-cost retrofit noise controls for equipment. This report describes the procedure for the measurement and reporting of noise from portable pneumatic tools such as jackleg drills. The technique used in this research allows for the determination of the source A-weighted sound power levels and the radiation patterns in octave and 1/3 octave bands. Overall sound power level is also determined. This paper also reports the results obtained by using this procedure to evaluate a SECO S215 standard production drill and a CSIR Miningtek prototype rock drill incorporating engineering noise control measures. It was found that by using the manufacture?s recommended operating pressure of 496 kPa (72 psi) that the CSIR prototype?s sound power was 10 dB(A) less then that of the SECO S215.

Jan 1, 2009

The Technical Study Panel on the Utilization of Belt Air and the Composition and Fire Retardant Properties of Belt Materials in Underground Coal Mining (hereafter referred to as the Panel or the TSP) was established by Section 11 of the Mine Improvement and New Emergency Response Act of 2006 (MINER Act). The Panel was charged with providing “independent scientific and engineering review and recommendations with respect to the utilization of belt air and the composition and fire retardant properties of belt materials in underground coal mining.” The TSP was impaneled by the Honorable Elaine L. Chao and commenced its work on January 9, 2007. At this first meeting, Mr. Richard E. Stickler, Assistant Secretary of Labor for Mine Safety and Health, asked the Panel to report on many issues including how recent technological advances could be applied to atmospheric monitoring systems, point-type heat sensors, current state of fire-resistant vs. fireproof belt materials, and belt fire suppression systems to improve miner safety. In addition, Mr. Stickler asked the Panel to review belt air velocity limitations. The Panel members attended 12 days of public meetings over a nine-month period. Three of the public meetings were scheduled for the Panel to hear from technical experts and those persons or organizations interested in providing input. The meetings were held in Coraopolis, Pennsylvania with emphasis on belt fires, belt maintenance, belt flammability and toxicity, ventilation, and escape issues; in Salt Lake City with emphasis on ground control and convergence issues; and in Birmingham with emphasis on fire detection, sensors and atmospheric monitoring systems. National Institute for Occupational Safety and Health (NIOSH) researchers, Mine Safety and Health Administration (MSHA) personnel, representatives of the major belt conveyor manufacturers and a representative of the National Mining Association provided discussions at the Coraopolis meeting. In Salt Lake City, Utah, MSHA district managers and ventilation specialists, a member of the Aracoma Mine No. 1 investigation team, a representative of the Bureau of Land Management, and industry and consulting representatives of the Utah Mining Association and the Colorado Mining Association made presentations. In Birmingham, Alabama, atmospheric monitoring system representatives, NIOSH researchers, representatives of coal mining companies, and UMWA workers from two Alabama mining companies made presentations. In addition, a staff member of The Center for Regulatory Effectiveness also presented comments to the Panel. In conjunction with the meetings in Salt Lake City and Birmingham, three-member subcommittees of the Technical Study Panel made field visits to the Skyline Mine, the Aberdeen Mine, and the Jim Walter Resources Mine No. 4. The mine visits were scheduled to see first-hand the mining conditions under which belt air was being utilized as an additional source of intake air for working sections.

By R. Barany

The heats of the glass-crystal transformation of nepheline (Na0.7794K0.2206AlSiO4) and wollastonite (CaSiO3) and the heat of formation of nepheline at 298.15° K were determined by solution calorimetry. For the glass-crystal transformations, the heat values were -9.0 ± 0.3 kcal/mole for nepheline and -8.1 ± 0.2 kcal/mole for wollastonite. The heat of formation of nepheline was -34.8 ± 0.6 kcal/mole from the oxides and -501.0 ± 0.5 kcal/mole from the elements.

Jan 1, 1966

By G. R. Friggens

A nuclear method for continuously monitoring the coalbed and ash levels and void formation in commercial-scale, fixed-bed, pressurized gas producers is proposed. Measurement of gamma ray transmission through the coalbed is the basis of the method. The coalbed level is monitored by detecting the trans-mission of gamma rays from a 1 to 2 Ci Co-60 source positioned on the outside wall of the vessel. Coal bridging or, alternatively, ash level is monitored by a 10 Ci Co-60 source at the center of the coalbed. Source activities and geometries are calculated for a 12-foot-ID producer designed to operate at 350 psi. Source capsule and detector specifications and operational safety are also discussed.

Jan 1, 1973

To develop a quick, safe, and effective method that allows workers at mineral processing operations to clean their dust-soiled clothing periodically throughout the workday. Background Reducing workers' respirable dust exposure to silica and other harmful dusts and contaminants is an ongoing goal in the U.S. mining industry. One area of known worker exposure is from contaminated work clothes. A U.S. Bureau of Mines report documented a number of cases where a tenfold increase in a worker's dust exposure was measured from contaminated work clothes. In these cases, the dust emitted from clothing caused the worker's dust exposure to exceed the permissible exposure limit in less than 2 hours. The most effective way to eliminate this dust source is to have workers clean or change their work clothes. There are two federal regulations that impact the clothes-cleaning process. The first states that at no time shall compressed air be directed toward a person, but that when compressed air is used, then all necessary precautions shall be taken to protect persons from injury. The second regulation states that compressed air should only be used for cleaning purposes when it is less than 30 psi and used along with personal protective equipment. For the mining industry, by default, the only approved method to perform clothes cleaning is to have workers vacuum their clothes using a HEPA filter system. This is very difficult and time-consuming and, in most instances, not very effective. Most workers would prefer to use a single compressed air hose to blow dust from their work clothes. However, not only is this method prohibited by law, it usually creates a significant dust cloud in the work environment and contaminates coworkers.

May 1, 2005

By Kenneth J. Miller

The Bureau of Mines conducted an investigation to improve the flotation response of coals that are difficult to wash by froth flotation. A literature survey and experimentation showed that, for the most part, refractory coals can be floated with oily collectors and frothers. Collector reagent consumption can be minimized and the selectivity of the flotation enhanced by assuring adequate, but not prolonged, reagent conditioning. Where flotation selectivity is especially poor, two-stage rougher-cleaner flotation is recommended. It was concluded that a major problem with refractory coals is predicting when they will appear in a flotation circuit so that supplementary flotation collectors can be added. Coal losses due to variation in the floatability of the feed might be reduced if a nonpolar collector such as kerosine or fuel oil is used along with a frother as general coal flotation practice.

Jan 1, 1977

To recover metals as sulfide concentrates from contaminated waste streams using hydrogen sulfide (H2S) generated by the bacterial digestion of waste organic materials. Approach The goal of this research is to develop a treatment method for metal mine effluents that will rival the cost and convenience of conventional lime treatment, and that will provide better effluent water quality, result in less expensive sludge disposal, and allow for the selective recovery of metals.

Jan 1, 1993

By Fred N. Kissell, J. E. Matta, J. C. LaScola

The Bureau of Mines made laboratory absorption measurements on oil shale samples, which showed that the amount of methane absorbed is proportional to pressure and oil yield, and can be much larger than would be predicted based solely on porosity. Oil shale cores collected in the field were also measured for their gas content using the Bureau of Mines direct method, Cores taken from deep locations and far from outcrops yielded more gas than cores from shallower locations or at outcrops, when taking into account variations in oil yield, and all data indicate that oil shale mines that are both deep and far from an out- crop will emit low levels of methane gas.

Jan 1, 1977

To cool hot working environments in deep mines more efficiently, while substantially reducing the maintenance required by presently used cooling coil heat exchangers. Approach A mine's chilled water supply cools fresh air enroute to hot working areas, in an improved, direct-mixing heat exchanger. How It Works Warm, fresh ventilation air traveling through the mine's ventilation tubing enters the lower portion of the cooler heat exchanger through a large round opening designed to accept the ventilation duct. This air flow is turned upward and evenly distributed by egg-crate lattice and pair guide vans at the bottom of the cooler. On the diagram, warm air enters at the bottom left. As the air moves upward through the cooler, it passes through a plastic or wire mesh pad which is arranged so that it offers the most resistance to upward airflow immediately above the cooler inlet: this more or less equalizes the upward air flow along the length of the cooler. The air next moves through the cold water sprays, and then through a wire-mesh demister pad before exiting from the cooler at the top right. Cooling of the air is accomplished in several stages. As the incoming air passes through the lower plastic or wire mesh pad, it is exposed to water flowing downward through the pad to the water sump. This is water that has fallen from the sprays or dripped from the upper wire-mesh mist eliminator. This water is slightly warmer than the spray water since it has already done some cooling,

Jan 1, 1981

Improve the safety of mine workers by developing a means of forecasting impending roof falls in underground mines. Approach The Bureau of Mines, through in-house and contract research, has developed the Roof Fall Warning Device. This battery-operated, portable electronic system forecasts roof falls by detecting and interpreting high-frequency rock noise, The technology has shown potential for detecting stress-related failures in a variety of underground environments. How It Works All geologic materials produce high-frequency acoustic emissions when they encounter an increase in stress. These ultrasonic frequency range events ( >20kHz) are well above the audible range of human hearing, very small in amplitude and duration, and can only be detected with sophisticated electronic equipment.

Jan 1, 1990

By D. R. Forshey

The recent occurrence of fatal accidents in copper mines, presumably due to premature ignition of loaded holes by the heat from reacting ammonium nitrate-fuel oil (AN-FO) and pyrite-bearing ores, has led to an examination of this reaction. The reactivity of prilled AN-FO mixtures with pyrite-bearing ores and the effects of water, dilute sulfuric acid, and potential inhibitors on reactivity of the mixtures were evaluated. Initiation of an exothermic reaction was observed as low as 150° F with acid in the absence of inhibitors. Low concentrations of urea, calcium carbonate, zinc oxide, and magnesium oxide were effective in inhibiting the reactivity of the mixtures. The temperatures produced during the reaction of mixtures of AN-FO and pyrite-bearing ores, in the absence of inhibitors, always exceeded the temperature at which electric blasting caps are thermally initiated.

Jan 1, 1968

Control dust generated during undercutting in salt mines without causing ore-solubility problems that result from excessive water use. Approach A foam generator was developed to provide a reliable foam to control dust on cutting machines used in mining water-soluble ores. The system was designed to keep total foaming agent/water mixture flowrates below the flow-rates characteristic of water-only systems. The foam generator consists of a reservoir to hold the premixed agent and water, a metering pump, and a small compressor to aerate the mixture. The system is compatible with all cutting machines. How It Works One of the current wet-bar techniques, the through-the-bar trickle system, pumps water through a pipe in the cut-ting bar to its tip placing the water behind the kerf. If the pipe conducted foam effectively the foam would be released in the kerf where it would mix with the cuttings and the dust produced by the chain. For improved foam delivery, however, it is recommended that the pipe be replaced with an external channel welded along the top of the bar. This provides excellent dust control while avoiding the accumulation of copious quantities of foam in the heading. The system is very simple. The foam generator is a 50-gallon tank filled with a mixture of water and foaming agent. The mixture is pumped through a wye fitting to a second line where it is mixed with compressed air, (300

Jan 1, 1984

By J. F. Barkley

The following questions and answers were prepared principally to supply information in answer to general inquiries received by the Bureau from those contemplating the use of propane and butane fuels . Primary or basic information only is covered; this usually gives enough guidance for most inquirers . To those who wish information of the treatise type , the handbook , Butane- Propane Gases , published by the Jenkins Publications , Inc. , 1709 West 8th Street , Los Angeles 14, Calif . , is suggested .

May 1, 1949

By D. B. Dow

"In the natural-gas Gasoline industry, the methods used in determining the amount of gasoline in natural gas are many and varied; they include the specific-gravity test, laboratory tests involving absorption, charge in volume of the gas or in the absorption medium, absorption in charcoal with subsequent distillation, compression of the gas which results in the condensation of the gasoline, and the absorption of the gasoline vapors in an absorption oil, from which the gasoline is distilled and measured. Each of these various tests has advantages, and disadvantages. It is however, conceded in the industry that the tests in which the gasoline is obtained and measured as such are the more reliable.This paper deals with certain factors which should be considered in making absorption tests using ""mineral seal oil"" as an absorbent; this method of testing is widely used not only in the field, but in control work in absorption gasoline plants where the gasoline content of the intake and discharge gas is determined daily. In control work it is frequently found that the plant produces more gasoline than the tests show, which gives the plant the appearance of making more gasoline than is actually present in the gas treated, or in other words operating at more than one hundred per cent efficiency. Obviously then, the tests as made in these cases are in error, and in hope of correcting some of these variances, the following factors have been studied at the U. S. Bureau of Mines petroleum station at Bartlesville, Oklahoma."

Aug 1, 1920

This Information Circular from the National Institute for Occupational Safety and Health (NIOSH) documents and supplements the information presented in a series of workshops held during 2002 and 2003. The primary intended audience consists of all who are involved in developing and conducting miners? training. According to the Mine Safety and Health Administration (MSHA), mine operators reported 240,000 full-time equivalent workers and independent contractors reported 42,000 full-time equivalent workers working on mine property during the year 2000. Unfortunately, these workers have a relatively high risk of suffering serious work-related injuries and illnesses. The mining industry has the highest rate of occupational fatalities among all U.S. industries. The fatality rate is 30 deaths per 100,000 workers compared to 4.6 for all private industry(Morbidity and Mortality Week Report, 2001; NIOSH, 2002).Compared to workers in other industries, miners also have a relatively high rate of nonfatal lost-time injuries, and their injuries tend to be more severe (Bureau of Labor Statistics, 1999). Many miners are also exposed to significant health hazards, including coal and silica dust, diesel exhaust, and noise. More than 1000 U.S. miners die of lung disease each year(NIOSH, 1999).

Jan 1, 2002

By D. W. Frommer

Processing of nonmagnetic taconites by selective flocculation-des liming and anionic flotation of calcium-activated silica has been investigated using innovative procedures as a means of improving operating costs. Areas chosen for cost-cutting evaluation were grinding, fine screening, and water conservation and reclamation. The investigation was performed on Marquette range nonmagnetic taconites in the Bureau of Mines Twin Cities Metallurgy Research Center flotation pilot plant, at feed rates ranging between 900 and 1,100 lb/hr. With fully integrated water reclamation, flotation concentrates containing 65.8 percent Fe and 3.4 percent Si02 were made in the best operating period, with accompanying weight and iron recoveries of 40 and 74 percent, respectively. During this same period, the estimated cost of both flotation and water reclamation reagents was only $0.80 per ton of concentrate (1968 pricing basis). This cost is about 15 percent lower than obtained previously at this Center for flotation reagents only. The investigation demonstrated additional potential savings in operating costs of approximately $0.96 per ton of concentrate through autogenous grinding as a substitute for ballmilling. Fine screening of intermediate concentrates was employed advantageously, but the frequency of blinding may be a factor militating against use of the screen in this flotation system.

Jan 1, 1973