Search Documents

By C. Melvin Lepper

To provide the U.S. mining and energy industries with information in the selection of seismic detectors for high-resolution applications, the Bureau of Mines evaluated 35 velocity detectors (geophones) and 9 accelerometers. It was found that velocity detectors with natural frequencies from 10 to 100 Hz were effective for seismic studies in the 5-to 600-Hz spectrum and that accelerometers were most effective in the 100-to 1,000-Hz range. Although the accelerometers described in this report performed about equally with the better velocity detectors tested, the accelerometers showed higher output voltage levels at higher frequencies, which is an advantage. It is important that a seismic detector and its intended purpose be matched properly to achieve the intended results in high-resolution applications. There are many factors that could affect proper matching, thus careful selection of the best detector for a particular application must be exercised.

Jan 1, 1981

By E. F. Ferrell

Gold was recovered from scrap electronic 60-40 (tin-lead) solders by drossing with aluminum or zinc at elevated temperatures. The gold, together with other metallic impurities, collected in the dross phase which could then be separated from the molten solder by skimming or filtering. Drossing upgraded the gold concentration by a factor of 10. Further upgrading was achieved by a combination of steps including an oxidation roast and either a combined cyanidation-amalgamation treatment or an aqua regia leach. The gold was then recovered in highly concentrated form from the aqua regia or cyanide solutions by cementation and from the amalgam by volatilization or dissolution of the mercury. The solder was purified by reaction with NaOH to remove dissolved aluminum or with SnCl2 to remove dissolved zinc.

Jan 1, 1976

By G. B. Fritts, A. C. Moschetti

"INTRODUCTION The act of Congress establishing the Bureau of Mines in 1910 delegated to the Bureau, as one of its principal duties and functions, the study of health and safety in the mineral industries with a view to devising and putting into operation means of conserving the health and safety of persons employed in the industries. One of the first health and safety activities of the Bureau of Mines was therefore organization of a trained force to promote instruction in first aid in the mineral industries. First-aid training has been an important activity of the Bureau of Mines since its establishment. The standard first-aid course requires a minimum of 15 hours of instruction and practice work. A person completing the initial training course is issued an engraved certificate and pocket card certificate; thereafter, only a pocket card certificate is issued for additional training.From 1910 to 1926 first aid was taught by trained Bureau of Mines employees; consequently, only a comparatively few persons were trained. In 1926, however, cooperative first-aid training was initiated, which provided the means to train the entire personnel of mines or plants within a short time in a single campaign. Many mines and plants have taken advantage of the cooperative plan, whereby keymen in a mine or plant, in addition to the initial training received, are given intensive training in first aid by a Bureau of Mines instructor. Those men who show an aptitude for teaching are selected as tentative provisional first-aid instructors. In order to qualify as a provisional instructor, a tentative instructor must, under the supervision of a Bureau of Mines instructor, train a class of at least six persons employed in the minerals industries in the standard Bureau of Mines course in first aid. After it has been determined that the class has been trained properly, a provisional first-aid instructor's pocket card certificate is issued to the class instructor. The first-aid instructor can renew his pocket card certificate each year by training or retraining at least six persons connected with the mineral industries to satisfactorily pass an examination given by a Bureau of Mines representative. After five yearly renewals of a provisional instructor's pocket card certificate, an engraved, permanent instructor's certificate and a permanent instructor's pocket card certificate are issued to the instructor."

Feb 1, 1955

By Je M. Oh

The Bureau of Mines is conducting research to determine the high temperature oxidation resistance of substitute stainless steels (SS) containing two less strategic elements, Al and Si, instead of Cr. Chromium is considered to be a critical and strategic metal. Although the Cr content was reduced to 8 wt pct, the alloys showed better oxidation resistance than did 304 SS containing 18 wt pct Cr. Specifically, the alloys that contained Fe-8Cr-16Ni with combinations of Al and Si showed excellent oxidation resistance even at temperatures up to 1,000° C. In this study, the effects of the alloying elements on oxidation kinetics and morphology of oxides were investigated using a Cahn Rg electrobalance, scanning electron microscopy, an energy-dispersive X-ray analyzer, X-ray diffraction, and an electron microprobe. Aluminum and silicon additions in combinatin were more effective in providing oxidation resistance than either element was alone.

Jan 1, 1986

By G. E. McClelland

As part of its mission to assure an adequate domestic supply of metals essential to the Nation's welfare, the U.S. Department of the Interior, Bureau of Mines, investigated a particle agglomeration technique as a means for improving the flow of leaching solution through heaps of clayey or finely crushed, low-grade, gold-silver ores. Bench-and pilot-scale experiments showed that the percolation rate of cyanide leaching solution was markedly enhanced by mixing the ore with a portland cement binder, moistening the mixture, and mechanically agglomerating and aging the feed prior to heap building and leaching. The rate of gold and silver recovery markedly increased because of the increased, uniform percolation of leaching solution through the agglomerated feed. The use of concentrated cyanide solution instead of water during the agglomeration procedure decreased the leaching time required to obtain maximum recovery. Results of bench-and pilot-scale experiments are discussed.

Jan 1, 1981

By Albert E. Long

Diamond-bit performance and cost data accumulated in core-drilling sandstones reveal significant trends of economic interest. Large-size, AA-Grade drill bort suffered less diamond loss per foot drilled than any other size or grade of diamonds assessed. Detailed analyses of the factors that affect diamond-bit performances -diamond size, diamond quality, bit size, bit type, percentage of core recovered, and physical characteristics of bit matrices -are assessed in the tables, graphs, and discussion. INTRODUCTION Since 1945 the Bureau of Mines has been compiling detailed performance records on diamond bits used in core drilling throughout the United States and Alaska. Analytical reports covering bit performance in various rocks are issued as in-formation on a significant number of bits used in anyone type of rock is accumulated. The first three such reports analyzed bit performance in gneiss,2/ schist,3/ and lime-stone and dolomite.4/ This report evaluates diamond-bit performance in sandstone. Data obtained from 627 bits, which drilled 42,665 feet on 45 different projects, are presented. The geographical distribution of the projects is shown in figure 1.

Jan 1, 1958

By Herbert H. Fields

The Bureau of Mines has been promoting health and safety in mining since its establishment in 1910. One area of research covers methane control in coalbeds; this report describes a multipurpose borehole used for both degasification and the production of commercial-quality gas. The multipurpose borehole was drilled into a barrier pillar, and seven horizontal degasification holes and one pressure point hole were drilled radially out from its perimeter. On January 28, 1974, after 505 days of degasification, a compressor was installed to the exhaust stack of the multipurpose borehole (1), and pipeline--quality gas was introduced into a commercial pipe-line. As of February 4, 1975, over 171 million cubic feet of gas had been purchased by the gas company. The in situ pressure at a depth of 200 feet into the coalbed and the average gas flow and water flow from the degasification holes as they were completed and closed off were 203 psig, 1,200,000 cfd, and 6.8 gpm, respectively. Twenty-four hours after the seven holes were connected through individual pipes to the atmosphere, the total gas and water flows and the in situ pressure dropped, respectively, to 971,000 cfd, 1.3 gpm, and 18 psig. Five hundred days later, the corresponding values were 620,000 cfd, 0.15 gpm, and 10.5 psig. Daily flows have been as high as 800,000 cfd, and as low as 360,000 cfd, during the last 500 days. On February 4, 1975, after 882 days of degasification, 576 million cubic feet of gas had been removed from the Pittsburgh coalbed; apparently a much larger area of virgin coal is being degasified than is defined by the holes. This study indicates that horizontal boreholes drilled into a coalbed from the bottom of any shaft will effectively remove gas from the Pittsburgh coalbed,

Jan 1, 1975

By Linda L. Chasko, Charles P. Lazzara, Ronald S. Conti, William J. Wiehagen

Fire has long been a concern for underground mine workers. A mine fire can occur at any time and can result in a partial or total evacuation of mine personnel and the loss of lives. Fires can grow rapidly. Time is the critical element. Prompt detection, timely and accurate warnings to those potentially affected, and a proficient response by underground miners can have a tremendous impact on the social and economic consequence of a small underground fire. Fire preparedness and response have components of technology and people. These components can work synergistically to reduce the time it takes to bring the system back in balance. This report deals with the preparedness of miners to respond to underground mine fires. It is intended to aid the mining industry in understanding the various roles of emergency responders and the training techniques used to increase their skill levels. The report also presents a technology overview to assist in effective response to mine fires.

To improve electrical safety and lengthen light bulb life on trolley haulageways. Approach A resistor inserted in series with each pair of light bulbs, decreases the voltage applied to the bulbs and eliminates heavy arcing when voltages rise. How It Works Under certain conditions, incandescent light bulbs connected directly to a 300-volt d-c trolley wire can be a hazard, particularly during weekends when electrical equipment is nut in use. When little electrical power is being used, the voltage (on the trolley lines and at the substation) can rise to a value which will destroy the bulb filament, cause arcing, and damage the bulb holder. In one coal mine where light bulbs in certain locations fre¬quently failed, the problem was overcome by inserting a 100-ohm, 50-watt resistor in series with each pair of light bulbs. The light bulbs are rated at 300-volts and 100-watts. Figure 1 shows the light bulbs and resistor circuit. This resistance was added in order to reduce the current through a short circuited bulb holder, from several hundred amperes to a much safer value of 3 amperes. However, the resistor in series with each pair of light bulbs, also reduces the voltage across the lighted bulbs to approximately 240 volts during periods when the trolley line voltage is up to 300 volts. With this arrangement, no light bulb failures occurred over a 6-month period. The resulting light reduction has not been objectionable.

Jan 1, 1976

By Byron. O. Pickard

"An Arizona mining company recently demonstrated a new use for the geophone by successfully locating leaks in compressed-air lines which were buried under from 1-1/2 to 2-1/2 feet of fine rock fill. The following information is abstracted from data sent to the Bureau of Mines by the superintendent of the mine.The company has two parallel main compressed-air lines, about one and one-half miles long, buried under an average of two feet of fine rock fill. One of the lines is a four-inch high-pressure (1000 pounds) main, and the other line a ten-inch low pressure (90 pounds) main. The two mains are separated by a 10 to 3C foot interval, and run from the compressor plant to the No. 2 shaft, where they are taken underground. A pump line is also buried in the immediate vicinity.Several leaks, not audible enough to be located, were developed in the Alms. Various =Abode were suggested that did not seem practicable to the management. Finally, the company obtained a Bureau of Mines' geophone and experimented with it. The first test& were conducted while the pumps were running, and while there was noise on the concrete pavement, all of Which caused so much vibration in the geophone that it was impossible to detect the leaks.The second attempt was made at the close of the day shift when the compressors were not operating and when the pumps could be shut down. The valves in the far end of the surface lines were closed, and the lines were pumped to full pressure (90 and 1,000 pounds respectively).Geophone readings were then taken at 7 or 8 foot intervals directly see the lines. Several leaks some very large in the high-pressure line were audible with the geophone at distances varying from 15 to 30 feet. A con-le leak in the low-pressure line was found at a distance of 10 feet. detecting the leaks, no difficulty was found in locating them exactly. ""At this time"", laid the superintendent of the mine, are unable to large a leak must be in order to be located under two feet of loose geophone. The fill we worked over was quite loose and dry and unfavorable for the work in question. However, we have no that the instrument is a valuable adjunct to our business""."

Aug 1, 1922

By Michael S. Wieland

Recognizing the dynamic nature and possible range of toxic concentrations in the impending fume cloud prior to undertaking explosive blasting can reduce potential hazards and mitigate related incidents. The scaled cloud model was formulated to predict the relevant (major) toxic components in fume clouds released by nonideal mining explosives used for surface blasting. Natural turbulence unceasingly disperses the toxic molecules, widening (inflating) the fume cloud while diluting the concentrations, ultimately rendering nonhazardous conditions. The threshold cloud size depends upon the type and quantity of total explosives used and the cloud's thermodynamic condition. Though the scaled theory works for fume clouds with irregular (odd) shape, an equivalent upright cylindrical form is useful for rendering simple riskhazard scenarios. The cylinder's projection downward on the underlying terrain yields a circular 'shadow' marking the region threatened, thereby permitting a rough estimation of the potential hazards, were the cloud to settle down there. Wind causes the cloud to drift while it expands, so the shadow travels while it grows, until the risk hazard process is truncated at the nonhazardous threshold. The overall relative fume toxicity (RFT) is taken from the traditional Russian RFT rule, which utilizes only the two fume components that tend to dominate the resultant toxicity: carbon monoxide (CO) and total nitrogen oxides (NOx). Tabulated constants that characterize the fume spectrum in the cloud model were resolved for ammonium nitrate (94%) with fuel oil (6%), ANFO-94/6, using a refined thermodynamic work-principle. Comparable results were found with the reduction factor technique, when test results from the underground fume chamber were readjusted to reflect nominal field shooting conditions.

By I. S. Solet

This study, of the liquidus temperatures and densities of molten alloys of zinc and aluminum was made as part of a broader investigation on refining of scrap aluminum. One of the methods of refining involves the separation of liquid and solid phases by gravity segregation and by filtration. More accurate data were required on the liquidus temperatures and the densities of molten' mixtures of the metals than were available in the technical literature. New data on the liquidus curve were obtained by thermal analysis. The new temperatures are, for the most part) somewhat higher than those reported previously by other investigators. The density of molten mixtures of zinc and aluminum were found to be less than would be calculated by assuming that the two metals occupy the same respective molal volumes in solution as they do as pure metals.

Jan 1, 1949

By Nicholas Kyriazi

It is of interest to know how to obtain as high an absorption efficiency as possible from a CO2-absorption canister used in closed-circuit breathing apparatus. In this study the Bureau of Mines found that varying the bed depth and the cross-sectional area of a canister changes its absorption characteristics. In tests using four ,1 rectangular, variable-depth canisters with different cross-sectional areas, the Bureau found that, given a constant weight of the chemical absorbent, LiOH, and a constant COa input, the canisters with a greater cross-sectional area reached C02 levels of 0.5 volume-percent in the effluent gas sooner than did the canisters with a greater bed depth. However, resistance to flow through the canister increases with bed depth, and a trade-off is inevitable. It was anticipated that the efficiency of a canister would increase with increasing intergranular air space approaching the tidal volume of the breathing waveform and then level off at some point under 100 percent. This postulation was partially substantiated. Cylindrical and radial canisters were also tested and compared. It appears that shape is not as important a factor in absorption efficiency as bed depth, since neither canister differed significantly from the rectangular canisters with regard to absorption efficiency values.

Jan 1, 1980

Provide reasonably priced, reliable fire protection for loading shovels. Approach An automatic fire, sensing and suppression system using both dry chemical and Halon 1301 was developed. It is more rugged than similar industrial-type fire protection systems. How It Works Temperature sensors detect heat from a fire, and trigger the system. These sensors are located inside the machinery house and under the house and shovel frame where it rotates around the crawler chassis ring gear. An alarm is sounded, and extinguishing agents are released either in the machinery house or in the ring gear area. The system can also be triggered by a manual control. If the fire Is detected in the machinery house, all power is shut down to the motor-generator sets, ventilation fan, and all electrical controls. Doors are automatically closed. After a delay to allow time for the ventilation fan to stop, Halon 1301, a gaseous fire extinguishing agent, is released inside the machinery house until it reaches a concentration of about 7 percent. This concentration is sufficient to extinguish a fire, but isn't toxic to personnel

Jan 1, 1980

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove, grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions 2 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1970

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

INPUT FORMAT INSTRUCTION FILE FOR PROGRAM MFIRE GENERAL RULES FOR DATA INPUT: $THERE IS NO NEED TO DISTINGUISH INTERGER AND REAL NUMBERS. $ $ SYMBOLS FOR NUMERICAL INPUT INCLUDE THE FOLLOWING $ $ 1234567890 -+BLANK $ $ * FREE FORMAT IS ALLOWED. COMMA AND BLANK SPACE CAN BOTH BE $ $ DELIMITERS. SEQUENTIALLY DISTRIBUTED BLANK SPACES ACT AS ONE $ $ DELIMITER. BLANKS ADJACENT TO A COMMA HAVE NO DELIMITING EFFECT $ $ * A ZERO INPUT CAN BE OMITTED BUT NOT THE DELIMITERS EXCEPT WHEN $ $ THE ZERO INPUTS ARE THE LAST ONES ON A LINE. $ $ * A LINE WHOSE FIRST NON-BLANK SYMBOL IS "$ IS AN INSTRUCTION $ $ LINE WHICH WILL BE IGNORED IN A PROGRAM RUN. $ $ * A LINE WHOSE FIRST NON-BLANK SYMBOL IS NEITHER ONE USED IN THE $ $ ABOVE LIST FOR NUMERICAL INPUT NOR "$, OR WHICH CONTAINS MORE $ $ THAN 3 SYMBOLS OUTSIDE OF THE LIST, IS A COMMENT LINE WHICH WILL $ $ BE SHOWN IN THE OUTPUT FILE. $

Jan 1, 1990

By W. R. Wrzensinski

This report presents the findings from a l-yr Bureau of Mines program in which sulfur concrete reinforcing materials were tested and evaluated to determine their resistance to corrosion. It also summarizes the permeation characteristics of sulfur concrete and the exemplary performance of precast, reinforced sulfur concrete structures in various industrial environments. The Bureau is furthering the development of sulfur concrete technology as part of a larger effort to find uses for the Nation's plentiful sulfur resources in construction materials. Sulfur concrete is a corrosion-resistant material that can be used in acid and salt environ-ments where conventional materials fail. Penetration of corrosion-inducing agents is minimized because of the low permeation characteristics of sulfur concrete.

Jan 1, 1988

By Joseph L. Condon

High-speed movies were taken of crater experiments in two-dimensional plates of Tennessee marble to study craters being formed primarily by stress-wave action. The contribution of gas action to the cratering process was minimized because the two-dimensional models did not contain the expanding gases from the explosive. Four burdens were studied for solid plates and one burden for a segmented plate. After cratering, the plates were reassembled for dye penetrant studies of fracturing. Flyrock velocities were calculated and related to the degree of fracturing, and compared with those from quarry shots. In general, the smallest burdens produced the highest flyrock velocities and the least amount of fracturing. Flyrock velocities compared favorably with initial flyrock velocities in quarry blasts, but did not show step accelerations due to gas effects as did the quarry blasts. The test with a segmented plate was used to simulate cratering in a jointed material and showed that stress-wave effects can be important for crater formation in jointed rocks.

Jan 1, 1972

By J. J. Forbes

The rapid increase in the quantity of coal being mined by stripping methods is one reason for the increased interest evinced by safety and other agencies in the hazards that are inherent in this Method of mining. The coal-mining laws of some States contain general provisions governing the mining of coal by open-cut methods, but none contains a complete list of specific safety regulations or laws for-the safe operation of such mines. The cool-mining laws of one State empower the head of the coal-mining inspection organization to proscribe regulations for coal-stripping operations and gave him the authority and power to enforce the rules and regulations promulgated by him.

Jan 1, 1944

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

7. Development of Acoustic Seal Checking System The acoustic approach was shown in Section 4 of this report to be the most promising concept for checking the seals. This section describes the development of this concept into a working hardware system to be used later in the field test program. This development effort included: (1) Theoretical analysis of the acoustic behavior in the mine using acoustic modeling- techniques. (2) Experimental determination of acoustic patterns in mine passages. (3) Refinement of the theoretical model. (4) Verification of final theoretical predictions in the quarter-scale laboratory model of a mine passage and seal. (5) Development of system specifications. (6) Development of the Acoustic Prototype Seal Checking System. 7. 1 Analysis of the Acoustic Seal Checker Concept The acoustic seal checker concept is based on a model which combines corridor acoustics and hole transmission theory. The idealized model for the mine sealing application is shown schematically in Figure 66. A high intensity acoustic- source is located in a corridor at a, position adjacent to the location to be sealed. The acoustic signal transmitted through the seal is monitored by a microphone pick-up placed on the opposite side.

Jan 1, 1973