Search Documents

By H. L. Burmeister

These properties were examined by a Bureau of Mines engineer in 1949. During 1950, these mines were studied by the Bureau to determine the possibility of increasing the production and augmenting the supply of fluorspar. As a result of this study, it was decided to core-drill the Knox-Yingling vein to test the continuation of fluorspar to a greater depth than that reached by mine workings. It also was desired to relate the present deposit with the Rosiclare formation. Development work by the Bureau of Mines was performed from February to May inclusive in 1951. Four diamond-drill holes aggregating 2,733 feet were drilled in the hanging wall of the vein.

Jan 1, 1952

By W. J. Fene

It is often desired to obtain samples of air in places where collection by ordinary methods is not feasible, as in shafts amore means of descent or ascent are not provided, in sewer manholes, in gas or water wells, in empty oil tanks, and in sealed areas in mines. Heretofore, when such sampling was required, it was necessary to utilize the aspirating method, which was not always satisfactory; and to obtain samples of air in deep shafts, it was necessary to use long sections of rubber tubing, which was not always available. DESCRIPTION OF NEW DEVICE A new method or "device" employs a common snap-type mousetrap to break the neck of a vacuum tube at the place where it is desired to collect the sample (see fig. 1). A mousetrap is mounted on one end of a block of wood 11-3/4 by 3 by 3/4 inches in such camper that a lead weight attached to the trigger hall spring the trap when the device is given a sharp jerk. A vacuum tube is placed on the other end of the block and held in place by a strong rubber band. A strip of corrugated rubber is placed on each side of the grooved block to prevent the tube from clipping when the sample is taken. An adjustable shoulder, provided with a rubber cap, is pieced se that the neck of the vacuum tube will rest on it. The shoulder is made adjustable to accommodate various sizes of tubas and to keep the neck of the tube from breaking tee far back from the point. A metal handle is fastened to one end of the block, with a hole in the end through which the brass wire used for lowering the device is tied. The device is enclosed by a strong wire-gauge covering, hinged on one side and so arranged that it can be locked shut on the other side. This covering prevent: breaking of the tube while it is being lowered or raised in a shaft or other place. Brass wire of not less than 22 gage should be used for lowering the device. A detailed drawing of the device is shown in figure 2.

Jan 1, 1940

By LB. Berger

"INTRODUCTION The use of gasoline engines as the motive power for lift trucks, tractors, and other types of mobile equipment operated in enclosed spaces, such as industrial plants and warehouses, may create a hazard because of the carbon monoxide present in the exhaust gases of the engines; gasoline-powered equipment should not be used in mines or tunnels. Because the equipment is mobile, local ventilation usually is impracticable, and general ventilation of the spaces is nec-essary to dilute and remove the carbon monoxide. To estimate the rate of ventilation required in such situations, information is necessary on the concentration of carbon monoxide in the exhaust gas and the rate at which exhaust gas is produced under given operating conditions. The purpose of this paper is to present data that may be used in making estimates of ventilation requirements.COMPOSITION OF GASOLINE-ENGINE EXHAUST GASThe exhaust gas of a gasoline engine consists mainly of carbon dioxide, carbon monoxide, hydrogen, oxygen, and unburned hydrocarbons (usually reported as methane), together with the nitrogen present as a residue from the air sup-plied for combustion. 3/ The exhaust also contains water vapor resulting from combustion of the hydrogen of the fuel. The water-vapor content is not included in exhaust-gas analyses calculated on a ""dry"" basis and is not involved in the estimation of ventilation requirements."

Jun 1, 1947

By Hylton R. Brown

Advertisements and articles in technical and trade journals announce the approach of a new age, in which plastics, light metals, laminated wood, and numerous other products or byproducts will be used in the construction of automobiles, airplanes, and furniture and equipment used in our factories, offices, and homes. Undoubtedly, after the war there will be many such developments which will introduce new manufacturing methods and new hazards to challenge the safety engineer. Already we know, from experience in laboratories and pilot plants where these new products are being tested, that there will be many fire and explosion hazards to be overcome. The danger of dust explosions may be one of the principal hazards, because thetic resins and other materials used in the plastics industry, as well as metal powders, wood dust, and other finely divided substances, are capable of forming explosive mixtures in air. Heavy losses of life and property have been caused by dust explosions in flour and feed mills, starch factories, and grain elevators, and it will be well to consider the possibilities that such losses may occur in any new industry and to provide all possible safeguards against hazards. Fortunately, we have learned something about the behavior of dust explosions and know something about the ease of ignition, limits of Explosive concentration, end pressure developed. Our efforts should now be directed toward the application of this knowledge in the development of safe operating practices.

Jan 1, 1945

By G. S. Scott

The flammability of trichloroethylene vapors in air has been determined in a 7-inch cyclindrical vessel. Saturated flammable mixtures were formed with air at atmospheric pressure between 30° C (86° F) and 82° C (180° F); the trichloroethylene concentrations at these temperatures are 12.5 (lower) and 90 (upper) volume-percent, respectively. Further study is necessary to assess the effects of different variables on the flammability of this material. INTRODUCTION Trichloroethylene (TCE) (ClHC = CCl2), sold under various trade names (Blacosolv, Perm-A-Clor, Tri, Triad, Triclene, Trivec, Tromex, Vapoclean, Vapoclor, Westrosol, etc.), is an important industrial chemical. A summary of its physical and chemical properties is given in table 1. It is used to degrease metals, leather, and textiles, to extract residual oils from vegetable oil cakes, for dry cleaning, and in soap. It is a powerful solvent for fats, resins, bitumens, rubber, sulfur, and phosphorus. Several explosions in which trichloroethylene was involved prompted an investigation by the Bureau of Mines to determine the conditions under which such accidents can occur.

Jan 1, 1963

By Sidney Katell

An estimated capital investment of $76,499,800 will be required for a plant designed and built to produce 90 million standard cubic feet per day (std.c.f.d.) of synthetic pipeline gas through Lurgi gasification of bituminous char. This investment figure does not include the pretreatment plant, the cost of which is assumed to be reflected in the cost of the char fed to the gasification system. Shift conversion, C02 removal, and methanation are required after gasification in the Lurgi unit to make a gas suitable for pipeline transmission. Capital investment data are based upon equipment costs, January 1959. Based on a 90-percent or 330-day operating year, the operating cost before profit and Federal taxes with the char price as a variable will amount to the following: [ ]

Jan 1, 1959

By M. Howard Berliner

"INTRODUCTION During the last 4 months of 1943, the Bureau of Mines engaged in an investigation and exploratory drilling program in the area between the Coughlin and Galena Level mines near the town of Shullsburg, in Lafayette County, Wisconsin. The work was undertaken as part of a general Bureau of Mines investigation of the zinc-producing area of southwestern Wiscon¬sin at a time when an effort was being made to increase the production of metals important to the Nation's war program.The portion of the southwest Wisconsin zinc district in the immediate vicinity of Shullsburg and the Coughlin and Galena Level mines is well mineralized. The principal ore horizon is at shallow depth, and there is evidence that relatively extensive surface mining for lead was done over a period of many years. Underground mining' for lead and zinc has continued to the present time.The Bureau undertook an exploratory drilling program in the area immediately west and southwest of the Coughlin mine workings after thorough preliminary investigations and geologic studies indicated that such work would serve to guide operators in the development of new ore reserves needed for continuance of mining operations in that area."

Apr 1, 1947

By A. W. Ambrose

"Records of individual wells form the basis for the successful operation of any company engaged in the production of petroleum. The expense attached to the compilation of records is negligible in comparison with the benefits resulting from their use. There a company has not a complete system of records, immediate attention should be given to the preparation of forms upon which to collect data, and, to the collection of data for these forms. The records needed vary with each district, but for each field a set should be adopted that will best meet the needs of each property. Practically all operators, and particularly all successful operators, agree on the necessity of good records, shopping what the wells have done, are doing, and may be expected to do in the future. Any operator realizes the value of records of sales of oil and should place almost equal emphasis on the records of well logs and histories showing the east and present performances of wells. Indeed, trustworthy records are absolutely necessary for the proper operation of any oil or gas property.Complete records should be kept on each well from the time the location and elevation are determined until the well is abandoned, and the engineer should review old records often enough to be familiar with the past performance of the various wells and with the conditions that affect production. Some of the forms that may be prepared are:--"

Mar 1, 1920

By A. L. Murray, C. A. Allen

"In the Spring of 1919, the Industrial Commission of Utah undertook the assembling of safety orders covering metal mining operations Just at that time there appeared several articles in the mining papers advocating the licensing of hoisting engineers, so this subject was given careful consideration,The licensing of hoisting engineers means that they must pass an examination covering the mechanical features of hoists and boilers, and must have a certain amount of experience. This undoubtedly serves to get a class of hoisting engineers that are better informed about the mechanical operation and theoretical considerations in hoisting and the only room for argument against it is that it is difficult to give an examination that will determine whether or not a man is a competent hoisting engineer.A man might pass an excellent examination yet be absolutely unqualified to operate a hoist and the judgment of the mine super- intelligent would have to be depended upon to choose the right man from among those who were licensed. This difficulty of properly determining, by ordinary examination, a man's qualifications to run a hoist caused the idea of licensing' in the ordinary sense of the word to be abandoned; but, as there was no question that a hoisting engineer should be physically fit, it was decided to require a medical examination, and at the same time to require the hoist engineer to state his experience, so the State would better knowledge of his general qualifications.The orders covering the question were therefore issued as follows;"

Jan 1, 1920

By S. H. Katz

Artisans and laborers in mineral industries where the air is dusty with particles of reel: are subject to a peculiar pulmonary disease known as miners' phthisis or stone cutters' consumption. In granite cutters the disease is specifically designated as granite pneumoconiosis. Very fine particles of the harder rocks are especially injurious when inhaled into the lungs. It is estimated particles about one micron (1/23000 part of an inch in diameter) are most injurious, because larger particles are more readily removed by the cilia and,wet surfaces of the respiratory passages before reaching the lungs, while smaller particles either do not readily lodge or are more easily eliminated. Silica, of which quartz and flint are composed, and which forms a large part of granite, is one of the hardest of the common rock-forming materials. It is also very insoluble when silica lodges in the lungs elimination is difficult. Rock constituents of granite other than silica are probably injurious but in a lesser degree, and this is also probably true of limestone and the softer rocks. Ultimately a worker who daily inhales much granite dust has considerable deposited in his lungs. If he continues at his trade the lung tissue becomes harder and less elastic, he finds himself short winded, and in extreme cases death may come either directly or indirectly as a result of lung failure.

Feb 1, 1921

By R. W. Stahl

Gas accumulation and dust suspension are the major safety hazards in coal stockpiling and reclaiming operations. This report presents a schedule of safety precautions and plant design features devised by the Bureau of Mines to reduce danger from these and other sources.

Jan 1, 1965

By Thomas Fraser

The Convertol process, recently developed in western Germany, is a new method of cleaning and dewatering coal-washery slurries. It is a modified bulk-oil process, in which a very small quantity of heavy oil is dispersed over the surfaces of the coal particles, followed by a screen centrifuge operation in which the water and dirt (clay, shale, and pyrite particles) are thrown out through the screen perforations and the clean coal particles are retained on the screen and discharged as a dewatered, clean coal product of 8- to l0-percent surface moisture. It is reported, also, that the process oil, all of which is retained in the clean-coal product, adds to the coking power of the coal and facilitates the production of briquets, reducing the proportions of binding material required.

Jan 1, 1953

By Robert H. Merrill

A method of determining the strength of a mine roof layer in place is described in this report. The method was tested on a limestone roof layer 50 feet wide, 100 feet long, and 20 inches thick. In place measurements were accomplished by introducing air under pressure into a separation between the layer and the overlying roof, and as pressure was increased, the corresponding strain and deflection of the roof layer were measured until the roof failed. The ultimate strength of the roof agreed with the tensile strength of the roof rock (modulus of rupture) as determined in the laboratory; the modulus of elasticity as measured in place did not agree with the laboratory-determined values; the deflection and tensile strain in the layer in place showed good agreement with the theory of a body-loaded beam clamped at both ends. This procedure for determining the strength of a mine-roof layer is safer and less costly than successively widening a roof to failure. For example, it would have been necessary to mine the room to a width of 114 feet and a length of 228 feet to produce failure in this roof layer. The method is not necessarily limited to limestone; any thinly bedded rock type can be tested by this procedure when there is an open parting over the mined area.

Jan 1, 1958

By Robert H. Essenhigh

A stirred reactor (SR) combustion system has been developed to gather information on the mechanisms of ignition and flame propagation of coal dust under conditions similar to those found in coal dust explosion flames. The prime scaling variable considered in this study is that of rapid particle heating (between 105 and 106°K/sec) which is accomplished by means of turbulent mixing during combustion. The SR combustors tested in this study have consisted basically of spheres hollowed in the centers of refractory housings. Coal and air mixtures have been injected into the spherical combustion chambers through a single jet, two opposed jets or four opposed jets. The diameters of the jets have ranged from 0.63 to 0.22 cm. The volumes of the combustion chambers have ranged from 1.0 to 0.2 liters. The reactors have been equipped with thermocouples embedded in the combustion chamber wall as well as a thermocouple located in the exhaust gas stream. In the latter versions of the SR, provisions were made for both solid sampling and gas sampling of the reactant stream exiting from the combustion chamber. Experiments have been carried out using pulverized bituminous coal. The coal has been reacted in an SR in mixtures of air and air/nitrogen. These experiments have provided information on the mode of ignition of the coal as well as yielding information on the kinetics of coal pyrolysis through the use of SR theory. Ash tests performed on the reacted samples collected from the SR indicated that the majority of the values of weight loss percentage were between 60 and 70 percent. The percentages of weight loss were relatively unaffected by changes in temperature which varied between 1100 and 1700°K and by changes in residence time which varied between 10 and 20 millisec. Volatile matter tests performed on the samples indicated that the volatile matter left in the char ranged from 3 to 20 percent of the original content. By assuming that all the mass loss was due solely to pyrolysis with no combustion occurring at the particle surface, Q-factors for each test have been calculated. The results of these calculations indicate an average value of Q equal to 1.88. This finding shows that the majority of mass loss can be attributed to pyrolysis. The fact that the extent of reaction varies only slightly over the range of test conditions has been examined in the context of the two component hypothesis of coal constitution. This approach leads to the conclusion that the reaction of the "easily evolved" component VMI is extremely rapid and that the majority of it is removed from the coal in times less than the residence time in the system. This means that the volatile residue remaining in the char can be considered to consist of component II, VMII. If the mass fraction of VMI = 0, then an activation energy of 18.0 kcal is obtained for the pyrolysis reaction. If the mass fraction is assumed to be 0.75, the activation energy increases to 31.2 kcal.

Jan 1, 1978

By J. T. McCartney

Thin sections of coal have been prepared for many years either by cutting on a microtome (1,2)5 or by grinding and polishing (2,1). Specimens of most coals had to be demineralized in hydrofluoric acid and softened in caustic solutions before they could be successfully cut with a conventional microtome. Some lignites could be cut without pretreatment. Jeffrey (1) obtained sections from coals of all ranks, although long and tedious pretreatment was required for anthracite. His sections were less than 1 cm.2 in area (probably much less for high rank coals) and about 5 microns thick. Thiessen (2) also cut sections of softened coals, mostly of low rank. His sections were a few square millimeters in area and about 3 microns thick. However, Thiessen preferred ground and polished sections for detailed studies because they were larger and had not been chemically attacked by softening media. He prepared ground sections as large as 4 cm.2 in area and usually 5 to 10 microns thick. Thousands of such sections, covering complete column samples of many coal beds, were studied for a number of years (4). With the development of the electron microscope and increased interest in quantitative optical studies of coals, a need for much thinner sections arose. However, no suitable technique for preparing such sections was known until Fernández-Morán developed a diamond knife for cutting ultrathin sections of hard materials (5). Workers at the Centre d'Etudes et Recherches de Charbonnages de France applied this new tool to the cutting of coal sections and have recently described their technique to the Burg, of Mines. Using their methods, with some modifications, researchers of the Bureau of Mines have succeeded in cutting ultrathin sections of coals ranging in rank from lignite to

Jan 1, 1961

By S. L. Windes

"INTRODUCTION For a number of years the bureau of Mines has been engaged in the detection, recording and interpretation of earth- and air-transmitted disturbances, man-made and natural, related to mining operations. For the measure¬ment of such disturbances, special equipment was developed (1, 2, 3, 4, 8) 3/ and results of the measurements have been reported (5, 6; 7,9).In general, the ranges of amplitude end frequency of vibration encountered and recorded in the earth-transmitted disturbances were 0.00005 to 0.1 inch and 5 to 5,000 cycles per second; in the air-transmitted disturbances, pressures ranging from 0.001 to 100 pounds per square inch and 0 to 20,000 cycles per second were recorded.One characteristic of the earlier tests was that either the arrival time of the disturbance to be recorded was predictable or the recording speed was slow enough so that the record covered extended periods of time (for example, 4 hours). As the investigations continued, it became apparent that a recording device was required that would respond to transient vibrations arriving at indeterminate times and at the same time provide a permanent record of displacement or acceleration versus time on a scale that would permit the analysis of waves having frequency components up to 10,000 cycles per second. A film or paper speed of 720 inches per second was found to be adequate, as this provides approximately 3/4 inch of record for each 0.001 second."

Dec 1, 1947

By S. M. Shelton, W. A. Calhoun, M. M. Fine, T. L. Johnston

"This report is () expansive test program by the Bureau of Mines to determine methods from various and ferrous manganese-grade product () widespread () and manfniferrous iron ores. Among the samples received for testing was one from the pits of the Barytes Mining Co., 1-1/ 2 miles northeast of Cartersville, Ga.. The property is approximately in the center of the Cartersville manganese district and shares a common corner with properties of the New Riverside Ochre Co. and the Etowah Development Co., both producers of manganifereus ores. The deposit is typical of the district and occurs in residual clays resulting from weathering of the Shady limestone and Weisner quartzite. 7/The property is developed by a number of open pits ranging to 60 feet in depth. In 1918 several carloads of manganiferous iron ore was mined from an alit on the property. Since then mining operations have been negligible. The ore is known locally as calico ore.A 4-ton sample representing -re as it occurs in the -pen pits vas furnished for testing. The sample consisted of a mixture of red iron oxides, wad, and clay, with small pebbles of manganese oxides and siliceous fragments scattered throughout."

Mar 1, 1943

By M. G. Pelipetz

High-pressure, high-temperature hydrogenation of coal has been known and practiced for many years. A full' understanding of the mechanism in this process by which coal is converted to oil and gas must rest on a critical interpretation of the manner in which external variables influence the rate and the course of the coal-hydrogenation reactions. Same Bureau of Mines studies on the effect of temperature, catalyst, and rank of coal on these reactions have been published. The effect of pressure was not studied in this earlier work, and the effect of reaction time was complicated by the interruption of long reaction periods in order to refill the autoclave with hydrogen. It is the purpose of this paper to present data from more recent autoclave experiments that extend the results of Storch, et al, on the kinetics of coal hydrogenation. These data must be explained by any comprehensive theory of coal hydrogenation; their detailed evaluation, however, will be deferred until a later publication.

Jan 1, 1949

By Edward F. Divers

The Bureau of Mines recently tested a sideboard device that is designed to act as an extension of conventional brattice, thus improving face ventilation of developing room-and-pillar-type coal mining. In these laboratory tests, an 8-foot-long rigid sideboard was mounted vertically along the left fender of a full-scale-model ripper-type continuous mining machine, rising to the mine roof to provide an air seal. It extended from the auger support frame pivot point outby along the fender. A novel water spray manifold was used to form an air seal between the sideboard and brattice. Tests showed improvement in face ventilation with the prototype device, and also demonstrated that water sprays can form an effective air seal over a fairly wide pressure range. Based on this preliminary study, subsequent improvements may make the sideboard concept much more effective, thus affording a simple, inexpensive technique to improve the effectiveness of face ventilation.

Jan 1, 1979

By C. W. Owings

When explosions have occurred in mines where rock dust has been used to some extent, generally to a very limited extent, the press has immediately characterized those mines as "rock-dusted." To persons familiar with the method of rock-dusting, it is apparent that if rock-dusting is done properly, if all mine surfaces are rock-dusted to within at least 40 feet of the faces of rooms and entries, and if the incombustible content of the dust is more than 65 per cent, there is little likelihood that an explosion of coal-dust will occur. The report that an explosion has occurred in a "rock-dusted" mine immediately conveys to the mind of the alert safety advocate the information that the mine is inadequately rock-dusted or that either dust sampling of the rock-dusted surfaces has not been done or, if done, the mine has not been redusted with sufficient promptness. Rules for Collection of Samples Collection of dust samples is by no means intricate, but a few simple rules must be kept in mind if the results are to be dependable. A sample must represent the true average conditions of the dust in the section or zone in which it is taken, and therefore 'the point at which the sample is to be collected must be selected with care. During an explosion much if not all of the dust on the ribs, roof, timber, and road in the affected region is blown into the air; the sample, therefore, should contain all loose dust and material on: the surfaces to a depth of about 1 inch, if that amount is present. If there is considerable sand locally along the track, care must be taken not to include enough of this material to vitiate the sale and distort the results; however, if the sand is distributed throughout the region being sampled it should be included. Dust should not be collected from recesses in the ribs, such as hitches cut for timber, as the character of the dust in such places is often different from that on the ribs proper. Samples should not be collected at points where the dusting machine has been loaded or at a point where the machine has stopped and discharged for a longer period than at other points on the entry or in the rooms. In short, the sample must represent AVERAGE CONDITIONS, and if there is any doubt as to the character of the dust it is far better to have too much combustible matter than too much incombustible matter in the sample, as it is best to err on the side of safety if it is necessary to err.

Jan 1, 1929