Search Documents

By Eugene V. Cilento, R. Clark Lantz, Kevin A. DiGregorio

"A microscope-based spectrophotometer has been developed to measure superoxide release from single pulmonary alveolar macrophages (PAM) or other phagocytes in culture. Results indicate that PAM respond to stimulation by phorbol myristate acetate (PMA). It appears that some PAM do not release 02 upon stimulation by PMA; however, those that do release 0, show differences in: (I) the total amount of 0, released, (2) the rate of release of 02 and (3) the time delay for release of 02. The significance of measuring 02 release from single cells is two-fold. It allows the simultaneous study of 02 release and electrical potential changes across the membrane of PAM and it allows the study of differences in 02 release among cells. Thus, the function of Normal PAM and the dysfunction of PAM exposed to coal dusts can be more closely studied on single cells.Pulmonary alveolar macrophages (PAM), free cells found in the lungs, protect the lungs by removing inhaled foreign debris and bacteria. The macrophages do this by engulfing and then internalizing the foreign matter (phagocytosis). Stimulation of PAM causes the release of super-oxide radical (02) which has been shown to be the primary metabolite involved in the killing of bacteria by phagocytes (3,8,12). The super-oxide radical is highly reactive and is spontaneously or enzymatically converted to other antibacterial oxidants, including hydrogen peroxide (H202), singlette oxygen ( 02), hydroxyl radical toil'), and hypochlorous acid (HOCl) (2, 3,8,11,12).Exposure of PAM to dusts may lead to dysfunction of this cell-type and to a greater risk of lung damage or infection upon subsequent exposure to toxic dusts. To date, much of the research with this cell-type has used cytotoxicity (cell death) as a measure of dysfunction. Although this is an important end point, PAM dysfunction may occur at doses below those which lead to cell death. In addition, dysfunction has been measured using large numbers of cells. In order to obtain a clear understanding of the mechanisms involved in dysfunction, measurements should be made on single cells. As mentioned earlier, one of the major roles of this cell type is its anti-bacterial actions. Therefore, asessment of release of superoxide radical in single cells is important in determining the functional behavior of PAM before and after exposure to dusts. Since measurements of 02 production have not been made on single cells the purpose of this study is to develop the methodology needed to study release of 02 from single cells.Recent studies have suggested that a relationship exists between the release of 02 and changes in the electrical properties of phagocytes. The change in membrane potential is thought to be the initial step in superoxide production (6,9). Stimulants which cause 02 release also cause changes in the transmembrane potential of phagocytes (9) and in the permeability of the cell membrane to ions (6). For example, stimulants which cause the release of 0, from neutrophils have also been shown to increase the membrane transport of Na+ , K+ and Ca+2 and stimulation of macrophages leads to increases in Na and perhaps Ca permeability with a subsequent change in membrane potential. In some cases, phagocytic activity has been shown to depend upon the extracellular concentrations of these ions (6). Holian and Daniele (7) have shown evidence that the redistribution ofcellular Ca in alveolar macrophages is an initial step leading to 0, release. In order to provide direct evidence that 02- production is related to electrical changes across the plasma membrane of phagocytes, these two phenomena must be analyzed simultaneously on single cells. Ultimately, measurements of 0, release using the methodology developed in this study will be combined with electrophysiological tech¬niques to study both superoxide release and membrane potential changes simultaneiously on single PAM, and to examine the effects of coal and mineral dusts on their physiological fu"

Jan 1, 1988

By Harold J. Bennett

This report deals with the processing and marketing of iron and steal scrap in the intermountain States of Arizona, Colorado, New Mexico, Utah, and Wyoming and the northwestern Plains States of Nebraska, North Dakota, and South Dakota. The quantity and quality of iron and steel scrap consumed in both the steel mills and iron foundries in these States in 1964 were decided by (1) the type of facilities used to produce an end product; (2) the availability of a dependable source of iron and steel scrap at competitive prices; and (3) the, ratio of the cost of iron in iron ore to iron in scrap. In recent years the quantity of scrap used per ton of steel ingot produced has decreased. The major individual. consumers of iron and steel scrap were the steel mills in Arizona, Colorado, and Utah, foundries in Utah and Arizona, and copper leaching, operations in Arizona, New Mexico, and Utah. About 2 million tons of iron and steel scrap was used by the iron and steel industry in 1964. Although there has been a decline in the amount of scrap used per ton of steel ingot produced because of changes in steelmaking methods, there has been a slight increase in the overall quantity of scrap used because of the increase in ingot production. It is estimated that the scrap consumption in the steel industry will increase by 19 percent by 1980. In addition to the scrap consumed by the steel industry, 273,000 tons of ferrous scrap were used by copper-leaching operations. Thirty-one percent of the ferrous scrap used by the steel industry in 1964 was purchased from dealers and other sources. The CF&I Steel Corp. (formerly The Colorado Fuel and Iron Corp.) at Pueblo, Colo., complemented its blast- and open-hearth-furnace operations with basic-oxygen converters in 1962. The basic-oxygen and open-hearth furnaces were charged with 30 and 90 percent scrap, respectively. Future use of the open-hearths would probably be used to supplement ingot production requirements. Because it was more economical to use less scrap and a high molten-metal charge, the United States Steel Corp. at Geneva, Utah, which uses the open-hearth process to make steel, charges the furnaces with 25 to 35 percent scrap. The Allison Steel Manufacturing Co. at Tempe, Ariz., uses a 100 percent scrap charge in its electric furnace. Although it was estimated that there were 327,000 tons of various grades of motor vehicle scrap generated in 1963, no estimates were made concerning the total quantity and grade of scrap available in the area. Most of the scrap used in the steelmaking industry originated within the area. It was advantageous to sell scrap generated in eastern Nebraska, North Dakota, and South Dakota to markets in the Midwest because of freight costs.

Jan 1, 1967

By V. A. Marple, K. L. Rubow, B. A. Olson

"A virtual impactor personal aerosol sampler (VIPAS) bas been developed for use in diesel-equipped mines to collect size-separated samples or diesel exhaust and mine dust particles in the respirable size range. This sampler consists or three stages: a 10-mm cyclone, a 0.8- µm cutpoint virtual impactor and two filter cassettes. The large non-respirable particles are removed in a 10-mm cyclone. The respirable particles from the cyclone pass through a 0.8- µm cutpoint virtual impactor with the particles larger than and smaller than 0.8 JI.ID (mine dust and diesel exhaust particles, respectively) collected on two 37-mm filter cassettes. The sampling How rate is 2 L/min so as to be compatible with the standard respirable dust sampler and personal sampling pumps. INTRODUCTIONThe mining industry has been increasing its use of diesel-powered equipment in underground mines, especially in coal mines. With this increased usage has come an increased concern regarding the health effects associated with inhaling diesel exhaust particles since they are in the respirable particulate size range. A Mine Safety and Health Administration (MSHA) advisory committee directed MSHA to develop a sampling protocol for diesel exhaust particles to assess worker exposure (MSHA, 1988). In addition, the National Institute for Occupational Safety and Health (NIOSH) has recommended that ""whole diesel exhaust be regarded as a potential occupational carcinogen as defined in the Cancer Policy of Occupational Safety and Health Administration"" (NIOSH, 1988).Past work, with cascade impactors in both the laboratory and in underground coal mine studies, has shown that the diesel exhaust particles are primarily in the less than 0.8 µm aerodynamic diameter size range whereas the coal dust particles are primarily greater than 0.8 µm (Marple et al., 1986; Cantrell, 1987; Rubow and Marple, 1988; Rubow et al., 1990a, b; Cantrell and Rubow, 1991). This work has been jointly performed by the University of Minnesota and Bureau of Mines researchers over the last 8 years. Typical particle size distributions for a diesel-equipped coal mine and an all electric coal mine are shown in Figure l. Note that the particles in the < 0.8-µ.m mode are the diesel exhaust particles (seen only in diesel-powered mines) and the particles in the > 0.8-µ.m mode are coal particles (seen in both the electric-powered and diesel-powered coal mines). Chemical mass balance analysis was also performed on these two size fractions to determine the degree of particle cross-contamination in the two modes. This analysis showed less than 10% cross-contamination, i.e., in coal mines Jess than 10% of the diesel exhaust particulate was collected in the coarse fraction and Jess than 10% of the mine dust was collected in the fine fraction (Cantrell, 1987; Rubow et al., 1990a)."

Dec 1, 1996

By Ronald S. Conti

This paper describes technology and training that has been identified for underground emergency responders. Historically, underground mine rescue teams have only received training in the course of actual emergencies, or in simulated mine environments, usually on the surface, with placards to identify objects and hazards. Also, while U.S. Federal Regulations require all underground miners to walk escapeways and conduct fie drills every 90 days in a smoke-free environment, this does not fully prepare them for the conditions that will be encountered in real escape situations. Therefore, it is extremely important that miners are provided with adequate technology and that training simulations are conducted in a realistic manner. A series of mine rescue training and mine emergency response development (MERD) exercises, and in-mine smoke training was developed, conducted, and evaluated by state and company teams, and by National Institute For Occupational Safety and Health (NIOSH) personnel. The training exercises were held at NIOSH&apos;s Lake Lynn Laboratory (LLL) and operating mines during the past several years. This training resulted in improved technology and training for mine rescue teams, fire brigades, first responders, and miners in general. For example, existing technologies were identified to help responders during exploration and recovery operations. These included various chemical light shapes, strobe lights, light vests, and laser pointers to identify team members. Most of these devices may be used to mark underground areas and certain mine materials. Strobe lights were used for mapping out escapeways and lasers were used to negotiate travel through smoke. Thermal imaging systems allow rescue personnel to see in darkness and through dense smoke, and allows the user to easily locate missing or trapped personnel and heated areas. A hands-free communication system showed potential for enhanced communications between team members, the fresh air base, and command center. A new team lighted-lifeline allows for flexibility in movements of team members during routine tasks and allows them to easily find their fixed position on the lifeline. Of all the technology evaluated by underground personnel, laser lights and lifelines were most beneficial in leading personnel to safety and out of the mine in smoke-filled passageways. A positive-pressure inflatable escape device (IED)/airlock, was used to isolate the "hazardous" environment from fresh air and allow rescue team members to traverse through. An inflatable feed- tube partition that can rapidly block large openings such as underground passageways or tunnels and simultaneously provide a feed-tube for high-expansion foam generators was also deployed during the simulations. These technological advancements have improved the state of readiness for rescue personnel and have increased the chances of survival for all personnel escaping from underground emergencies.

By John A. Davis, Karl L. Kithil

The principal deposits of carnotite, so far as now known, are con- fined to a well-defined area lying in the southwestern part of Colo- rado and the southeastern part of Utah (see Pl. I). Approxi- mately, this area is bounded as follows: On the east by a line ex- tending from a few miles east of the southwest corner of the State of Colorado, to a point about 6 miles west of Naturita, thence di- rectly north to the San Miguel River, thence along the course of this river and the Dolores River to Mesa Creek, thence toward the head- waters of Mesa, Blue, and Calamity Creeks on the south side of the Uncompahgre Mountains; on the north by a line extending from the last-named point westerly to the San Rafael Swell near Green River, Utah; on the west by a line extending from San Rafael Swell to the Henry Mountains, and on the south by a line extending from the Henry Mountains toward the southeast corner of the State of Utah. This area includes the main districts wherein carnotite has been found, claims have been located, and the ore produced. There are of course, extensive tracts within this area which do not contain carnotite in paying quantities. In places the carnotite beds have been entirely eroded or are not present, or lie so deep that mining is not practicable. The main deposits of carnotite within the area lie in different districts which in Colorado are as follows: Summit and Bush Canyons in Dolores and San Miguel Counties; McIntyre, Gypsum Valley, and Bull Canyon districts; the Paradox Valley, La Sal Creek, Roc Creek, Long Park, Hieroglyphic, Saucer Basin, and Hydraulic districts in Montrose County; Mesa, Blue, and Calamity Canyon districts and the Gateway area in Mesa County. The included dis- tricts in Utah are as follows: The Green River and San Rafael Swell district in Garfield County; the Thompson deposits in Grand County; the Dry Valley, Yellow Wash, and Lisbon Valley districts in San Juan County; the district around the Henry Mountains in Garfield County; and the deposits recently reported in Montezuma Canyon (south of Monticello) in San Juan County. Outside of the area described there are scattered deposits north of the Denver & Rio Grande Railroad at Coal Creek, near Meeker, Rio Blanco County; along Skull Creek and Red Wash, near Rangely, Routt County; on Horse Mountain, near Eagle, Eagle County, and in South Park, near Garos, in Park County, Colo. The claims leased from the Crucible Steel Mining & Milling Co. by the National Radium Institute are situated on the north side of East Paradox Valley, in the Long Park and Hydraulic districts. The National Radium Institute has mined no ore except from its leased claims in the Long Park district. For information regarding the general geology of the region, the probable origin of the ores, and descriptions of other carnotite deposits, the reader is referred to the literature on these subjects. The carnotite of the area described is deposited in a light-colored, cross-bedded sandstone that lies almost horizontal between the La Plata formation below and the Dakota sandstone (conglomerate) above, and is included in the McElmo formation, which is of Jurassic age. Underlying the white sandstone of the La Plata is the Dolores formation, or "Red Beds," which is plainly visible along and just below the rim rocks of the steep canyon walls in many of the carnotite districts. Along such canyons the ore crops out at different places, so that prospecting is comparatively easy. For ore on the benches and on the mesa prospecting is more difficult, especially where the ore lies at some depth and no surface indications are visible. The carnotite deposits are flat, lenticular, and irregular, varying greatly in extent and thickness. The carnotite itself forms incrustations on exposures of the white sandstone, in joints and fractures of the rock, and is deposited around and between individual sand grains, replacing the original cement. The Utah and Colorado carnotite is amorphous, and to the naked eye appears as a very fine yellow pow- der. It is often granular, and as a rule can be readily separated from the individual sand grains.

Jan 1, 1917

"Minimizing Particle Contamination During Generation of Fresh Dust for Inhalation Studies J. Abraham, MS, Mechanical and Aerospace Engineering, West Virginia University, 1995Correlating Lung Crackle Using Holographic Interferometry Ali Afshari, MS, West Virginia University, 1989Effect of Bit Wear on Dust Generation Mudassar Ahmad, MS, West Virginia University, 1992 The Effect of Surfactants on Suppression of Non-Wettable Particles Ali Alaboyun, MS, Mineral Engineering, The Pennsylvania State University, 1989 Geochemical Characterization of Kerogens, Shales, and Coal Refuse Associated with Allegheny Formation of Cases of Northern West Virginia Dick Andre, MS, West Virginia University, 1987Size and Mass Characterization of Airborne Particulate Matter in Underground Coal Mines Using Diesel-Powered Equipment Indranil R. Bardhan, MEM Report, The Pennsylvania State University, 1992Size and Mass Characterization of Airborne Particulate Matter in Underground Coal Mines Using Diesel-Powered Equipment I. Bardhan, R. V. Ramani, and J.M. Mutmansky, Mining Engineering, The Pennsylvania State University, University Park, PA, Final Report to the U.S. Bureau of Mines, April, 1994Particle Concentrations in a Hazelton Inhalation Chamber Shahram Bavani, MS, West Virginia University, 1985Use and Potential of Lazer Holographic Interferometry and Subsidence Model- Study of an Underground Room and Pillar Mine Richard Begley, MS, West Virginia University, 1984Development of a Mechanistic Model for Prediction of Subsidence in a Longwall Mine Richard Begley, PhD, West Virginia University, 1990Redesign of Micro-Orifice Uniform Deposit Impactor Steve Behm, MS, University of Minnesota, 1991Evaluation of a Two-Phase Spray System for Dust Suppression B. Belle, MS, The Pennsylvania State University, 1996Evaluation of a Two-Phase Spray System for Dust Suppression B. Belle and R.-V. Ramani, The Pennsylvania State University, University Park, PA, Final Report, September 9, 1996A Fracture Mechanics Study of Crack Propagation Mechanism in Coal: The Mechanics of Fine Fragment Formation Z.T. Bieniawski and R. Karl Zipf, Jr., Mining Engineering Department, The Pennsylvania State University, University Park, PA. Final Report, October l, 1988A Mathematical Model for the Prediction of Ambient Dust Concentrations in Mine Atmospheres R. Bhaskar, MS, Mining Engineering and Operations Research, The Pennsylvania State University, 1984Spatial and Temporal Behavior of Dust in Mines-Theoretical and Experimental Studies –R. Bhaskar, PhD, Mining Engineering, The Pennsylvania State University, 1987"

Jan 1, 1998

By John C. Edwards

Several experimental programs were conducted at the Pittsburgh Research Center to investigate the level of mine fire detection and alarm capability possible using state-of-the-art technology. These programs involved comparison of the response and alarm time of optical and ionization type smoke sensors to smoldering and flaming coal combustion in a smoke chamber. Coal combustion experiments conducted in the smoke chamber demonstrated that a CO concentration of 5 ppm above ambient corresponded to an optical density of 0.022m1. For the four smoke sensors for which a continuous analog signal was available, a smoke sensor alarm was defined as the average background signal plus ten times the peak-to-peak noise. This alarm criterion resulted in the association of the alarm for three of the four sensors with a smoke optical density of 0.022m-1. and 0.033m-1 for the fourth smoke sensor. The smoke sensors used in the smoke chamber studies were incorporated into large scale diesel fuel fire experiments conducted under normal ventilation conditions in the Safety Research Coal Mine (SRCM) at the Pittsburgh Research Center. These experiments showed that a diffusion mode smoke sensor alarmed earlier than a diffusion mode CO sensor; and, based upon the measurement of the optical transmission at the location of a pump mode ionization type smoke sensor that a pump mode ionization smoke sensor alarmed at an average smoke optical density of 0.021m" for the twelve experiments conducted. A series of 30 and 330 kW diesel fuel fire intensity experiments were conducted under zero airflow conditions in the SRCM. It was determined that :(I) thermal sensors are inadequate at 30 m from a 300 kW fire;(2) a diffusion mode ionization smoke sensor can be more effective for mine fire detection than a diffusion mode CO sensor;(3) recommendations can be made for sensor spacing in a mine entry based upon the measured CO buoyancy induced spread rates along the mine roof and the time for a developing coal fire to ignite a conveyor belt.

By George S. Rice, O. P. Hood

The need of protecting mines from the danger of inflow of natural gas from neighboring wells has become more apparent each year since it was found that oil and gas underlie the productive coal measures of Pennsylvania, West Virginia, Ohio, Indiana, Illinois, Kansas, Oklahoma, Colorado, and Wyoming, and, to some extent, the coal measures of other States. The proximity of the known gas and oil areas in the United States to the coal fields and the manner in which the fields overlap in certain States are shown in the map comprising the frontispiece (Pl. I). As the result of many requests received from various sources a conference to consider the protective measures necessary to insure the safety of mining operations in gas and oil fields was called by the Director of the Bureau of Mines to assemble in Pittsburgh, Pa., Feb- ruary 7 and 8, 1913. To this conference were invited a considerable number of gas-well, oil-well, and coal-mine operators within conven- ient distance from Pittsburgh, as well as State geologists and State mine inspectors from a distance. Gas and oil wells are also found near other kinds of mines, such as shale and limestone mines in western Pennsylvania, but these cases are so few that for this and other reasons it was deemed best to con- fine the present inquiry to the consideration of the questions involved in connection with coal mines. It was also not thought advisable to consider the protection of mines from other kinds of bore holes than those for gas and oil, such as coal-prospecting holes, drilled either with churn or diamond drills, or salt wells and artesian wells, because little trouble has been ex- perienced in mining operations from these classes of wells. There- fore the following papers and discussions concern almost entirely the following relations between coal mines and gas and oil wells: (1) Protection of coal mines froin gas and oil wells penetrating -through: (a) Open workings; (b) inaccessible spaces or goaves; (c) pillars, or coal which may be left as pillars. (2) The manner of drilling gas and oil wells passing through workable coal beds so as to provide protection for future mining. The preliminary inquiries of the engineers of the bureau had dis- closed that there was no uniformity in the methods of protecting mines against the leakage of gas from wells, that thousands of wells in coal fields are abandoned yearly without adequate plugging, and without surveys or records being kept to show the location of the holes, from which the casings are generally pulled. According to the State geologist of Pennsylvania, as many as 3,000 wells are being drilled annually in Pennsylvania, 2,000 of these holes being aban- doned within a single year. It is such unplugged, uncharted wells that are the greatest menace in mining. The quantity of gas that the wells produce, although not sufficient to be commercially avail-

Jan 1, 1913

Occupational illnesses are more difficult to identify than on-the-job injuries. Many illnesses related to occupational exposures may not be diagnosed until years after exposure; by that time, exposed workers may have changed jobs or left the workforce. Other approaches to identifying occupationally related illness are analysis of death certificate data (see chapter 2) and medical examination studies of workers known to have high exposures to hazardous agents. Figures 5-1, 5-3, 5-4, 5-6, 5-8, and 5-10 show, for each commodity, the percent of illness conditions reported to MSHA by nature of condition. Heart attacks that occurred on the job are reported without regard to work-relatedness. Figures 5-2, 5-5, 5-7, 5-9, and 5-11 show rates by year during 1986-1995 for selected conditions. Since there are many limitations on the accuracy of illness reporting, the frequencies and rates shown here should not be considered directly comparable across commodities. Figure 5-12 shows estimates for hearing loss by age among coal miners compared to a nonoccupationally noise-exposed population. These data come from a study by Franks [1996] of a group of audiograms obtained on coal miners by a commercial company. Using the NIOSH definition of hearing impairment, i.e., an average hearing threshold level for both ears that exceeds 25 dB at frequencies of 1,000, 2,000, 3,000 and 4,000 Hz, the figure shows that by age 30, more than 10% of miners suffer hearing impairment; by age 50, 90% of miners have hearing impairment. In contrast, only 10% of the nonoccupationally noise-exposed population suffer hearing impairment at age 51, and 50% of the nonoccupationally exposed population have hearing impairment at age 69. Figure 5-13 shows a similar analysis of commercial audiograms on male metal/nonmetal miners [Franks 1997]. At age 20, approximately 2% have hearing impairment using the NIOSH definition of hearing impairment described above. This increases to 7% at age 30, 25% at age 40, and 49% at age 50. In contrast, only 9% of the nonoccupationally noise-exposed comparison population have hearing impairment at age 50. Franks&apos; analysis showed a different pattern for female metal/nonmetal miners; they developed hearing loss at the same rate as would be expected for a non-noise-exposed female population.

Jan 5, 2000

By George S. Rice, W. L. EGY, H. P. Greenwald, L. M. JONES

CHAPTER I. INTRODUCTION AND SUMMARY. BY GEORGE S. RICE. PREFATORY STATEMENT. This bulletin describes the second series of coal-dust explosion tests conducted by the Bureau of Mines in the experimental mine near Bruceton, Pa. It covers a period from 1913 to 1918, inclusive, of more or less consecutive testing, during which many important conclusions were drawn regarding the way a coal-dust explosion may originate, the mechanism of an explosion, and the methods of pre- venting explosions and of limiting incipient explosions. The manuscript was prepared in 1918, but its publication had to be put aside during the World War for more pressing publications and it was not until this fiscal year 1922 that funds could be allotted for its printing. Meantime the general facts concerning methods of preventing explosions have been made known to the mining industry, with great advantage, it is believed, as explosions of coal dust in mines in the United States have become infrequent. This fact, however, must not lull the consciousness of mining men to the terrible potential danger that lurks in untreated coal dust. The experiments described in this volume should be of aid to them in planning to keep the ever present coal dust in an innocuous condition. The first series-reported in Bulletin 56, "First Series of Coal-Dust Explosion Tests in the Experimental Mine"-included only pre- liminary tests of the ability to start explosions of coal dust under the conditions in the experimental mine. After this fact had been determined and several violent dust explosions had been demon- strated before large audiences of mining men, the work had to be suspended in order that necessary repairs and extensions might be made in the fall and winter of 1911-12. Although the question of the possibility of coal dust causing explo- sions had been considered for more than a century, and much testing in laboratory apparatus and in small surface galleries had been done, coal-mining men generally did not believe that coal dust was explo- sive and considered that fire damp or gases of unknown composition were responsible for the mine explosions that had cost thousands of lives in the various coal-mining countries during the last century. As coal mines increased in number, size, and depth, explosions became alarming in their frequency. Finally came the Courriéres disaster in northern France, 1906, by which 1,100 lives were lost, and the following year in this country, the Monongah mine explosion, in West Virginia, which killed 361 men, and the Darr explosion, in Pennsylvania, which killed 239 men. These two disasters, both in December, 1907, led Congress to make an appropriation for an in- vestigation of the causes of mine explosions. The funds became available July 1, 1908, and the work was placed under the United States Geological Survey's technologic branch, with the late Dr. Joseph A. Holmes in charge. Before undertaking the investigations Dr. Holmes visited Europe, accompanied by the senior author of this bulletin, to study the methods foreign countries used to prevent mine explosions, to obtain details regarding tests being made in several countries, to procure safer explosives and better safety lamps for use in gaseous and dusty mines, and to study the methods used in coal-dust explo- sion tests in the recently completed galleries at Altofts, England, and Liévin, France, and in the older galleries at Gelsenkirchen, Germany, and Frameries, Belgium. At all of these stations the explosions tests were made in surface galleries. The Austrian gallery at Segengottes, near Brünn, Moravia, visited by the writer in 1911, is an underground gallery, but the testing done in it was limited, dealing with ignition of coal dust rather than with propagation. Although the results obtained in the foreign galleries had indicated that coal dust was explosive, mining men in the respective countries were of the opinion that the dust would not explode under mine con- ditions. This situation led Dr. Holmes to the conclusion that testing must be done in a real mine, to make certain that the conclusion would be reliable and would be accepted by the mining public as decisive.

Jan 1, 1922

By E. D. Gardner

The Bureau of nines, in cooperation with the mining companies of the Southwest, is conducting an investigating to ascertain the safest and most economical explosives to use in metal mines, and to ascertain the best methods of blasting under various conditions. A part of this investigation has been a study of drilling and blasting drift rounds in metal mines. This paper covers one phase of work on drift rounds and discusses the methods of loading the individual holes of the rounds. The blasting tests, on which this paper is based, were made at the Copper queen Branch of the Phelps Dodge Corporation at Bisbee, Arizona.

Jan 1, 1927

By Katherine Harding

This Bureau of Mines publication describes a practical approach to sampling that does not require elaborate statistical techniques. Simple steps are given for finding a cutoff point in the response from a repetitive survey. This procedure can be used to estimate the aggregate value of the characteristic being measured without waiting for a complete count from the survey. This is a useful technique when the reference periods are repeated at frequent intervals, such as monthly and quarterly, and when the statistical collecting agency is engaged in publishing timely data which must be accurate economic indicators.

Jan 1, 1971

By H. H. Fields, Joseph Cervik, G. N. Aul

Coal is a soft and brittle material. Drilling rates in the Pittsburgh coalbed using a drag bit exceed 3 ft/min at 2,500-pound thrust. However, maintaining the bit on a horizontal trajectory or parallel to bedding planes to attain lengths of 1,000 feet is difficult. This Bureau of Mines report presents a drill string configuration that can be guided through the coalbed. The angle of the borehole is measured periodically and by proper combinations of bit thrust and rotational speed (r/min), bit trajectory can be lifted or dropped to keep the bit in the coalbed. An example of a hole drilled to 2,126 feet is presented to show levels of thrust and rotational speed used to lift or drop the bit, the seemingly unexplainable events that occur, and the strategy used during drilling. Thrust levels during drilling range from 600 to 2,500 pounds. Hydraulic motors powered by a 30-hp, 440-volt motor provide ample power for drilling horizontal holes 2,000 feet long.

Jan 1, 1975

By William O. Vanderburg

This paper describing the practice at the Wolf Pongee concentrator at Federland, Colo., is one of a series on similar subjects being published by the United States Bureau of Mines. The author acknowledges the assistance of Loach, manager of the Wolf Tongue Mining Co., and of W. G. Roseborough, superintendent of the golf Tongue mill, in the preparation of this paper.

Jan 1, 1933

By Donald P. Schlick

This report presents a representative cross section of methods success- fully used to ventilate continuous-miner places as well as various factors that should be considered when selecting auxiliary ventilating equipment. Line brattice can direct fresh air to the active face reasonably well, provided that adequate area for installation is available. Continuous mining equipment, however, often restricts clearances to such an extent that proper installation of line brattice is impossible. Consequently, in many instances face ventilation is inadequate; therefore, many methods of auxiliary ventilation for continuous-mining equipment have been developed and have been discussed in this study.

Jan 1, 1963

By Robert H. Dickson

This paper describing the mining practices at the Verde Central mine at Jerome, Ariz., is one of a series being prepared by the United States Bureau of Mines on mining practices, methods and costs in various mining districts of the United States. ACKNOWLEDMENTS The costs contained in this paper were prepared by R. J, Huddleston, chief clerk, Verde Central Mines, Inc.

Jan 1, 1931

By Edward D. Thimons

The Bureau of Mines conducted a state-of-the-art study of techniques currently employed to close large openings in underground mines. A large opening was considered to be any opening over 10 feet high and having a cross section of at least 200 square feet. Five salt mines and one limestone mine were visited to observe various methods of sealing large openings. Because of the variations in conditions from mine to mine, no definite conclusions could be drawn as to which is the best method. In mines where waste material is available, stoppings built by piling waste material are efficient and economical. Where waste material is not available properly constructed brattice cloth stoppings are superior to those built from wood, concrete block, or urethane foams.

Jan 1, 1975

By John Gross

The modern practice of grinding ores so that often 80 per cent or more of the product is finer than 200 mesh makes it desirable to supplement sieve sizing so as to extend considerably the range of sizing. Moreover, the fact that the material finer than sieve size represents the major part of the work done in grinding emphasizes thick need in can investigation of crushing efficiency. A method based on the settling rate of particles in grater appeared to be most practical for sizing; finely ground ores. There are two possible methods of utilizing this principle: one based on free settling or sedimentation; and the other on separation by means of a rising; current of water, or elutriation. In sedimentation, mechanical entanglement causes material at the start to settle in a mass, and this persists throughout. As this feature is largely eliminated by elutriation, which permits a comparatively clean separation of the various sizes, the elutriation method was adopted.

Jan 1, 1929

By R. V. Ramani, P. M. T. White, D. Sutton

This review of literature is centered around ore evaluation and reserve calculations as generally used in the mining industry. Methods of data interpolation were reviewed with the object of determining a method that would best suit the evaluation of under- ground coal deposits. Further, computerized data library concepts as related to geological data were investigated together with a brief evaluation of the data requirements for the total project. Additionally, computer techniques for the processing of geological data with a view to generate management information for decision making were reviewed including hardware and software availability. 2.1 Interpolation and Extrapolation of Data The importance of accurate estimates of value parameters in terms of their geographical and geological distribution within a, mineralized body has long been recognized in the evaluation of metallic and non-metallic deposits. As the factors which affect mineral distributions and associations are better understood, accuracy, and reliability of estimation increases. The ideal objective is to develop a deterministic model with the capability of accurately predicting the value at any geographical location. The most important value parameters requiring determination in any orebody are the grade and the quantity of ore that can be mined at the stated grade. These two parameters are modified or qualified by others which include physical dimensions and physical and chemical characteristics of the ore value. Therefore, the

Jan 1, 1974

By M. A. Schellhardt

"INTRODUCTION The augmented demands for natural gas in many parts of the United States as a result of war have increased the need for information regarding the producing characteristics of natural-gas and gas-condensate-type wells capable of delivering large volumes of gas, as such information is important to the formulation of conservative and efficient operative and recovery practices.,For many years, the capacity of natural-gas wells to produce gas has received studied consideration by Bureau of Mines' engineers, and three reports 3/ on gaging gas-well capacities have been published. In Report of Investigations 2929, Pierce and Rawlins point out that for accurate gaging, the actual pressures at the face of the sand in the well and the relationship between such pressures and the rates of flow of gas through the sand must be determined. Their report describes a method of attacking the problem of determining the actual pressures at the sand by means of observations of pressures and volumes at the wellhead.In Report of Investigations 2930, Pierce and Rawlins explain how the fundamental relation"

Aug 1, 1944