Search Documents

By F. N. Kissell, C. D. Litton

This study ranks the factors impacting survival during a coal mine fire. It bas already been established that reducing time delays is the most important factor in saving lives. Consequently every event during afire is measured in terms d its duration, and the effectiveness d any action taken to improve survival is measured in terms d the time it saves. By ranking actions according to time saved these authors found that a comhination d actions was most effective. This combination was: • installing lifelines. • moderately decreasing air leakage and • decreasing the fire growth rate. Changing ventilation leakage alone was much less effective, as was altering the CO (carbon monoxide), sensor alarm threshold. These results confirm an earlier fault-tree study on escape from mine fires. The fault-tree study bad shown that, with the exception d delays, single factor changes have minimal impact. Significant reductions in fire fatalities only take place with multiple factor changes.

Provide reliable, early-warning fire detection instruments, telemetry, and control systems for noncoal underground mines. Approach Industrial-grade fire detection instruments and signal telemetry equipment were modified for long-term exposure to harsh underground mine conditions, then were installed in four mines to evaluate long-term performance and reliability. How It Works The elapsed time between the onset of a fire and its detection is critical because fires tend to grow in size and intensity with time. Early fire detection and warning permit the initiation of a mine's emergency plan (evacuation, fire fighting, etc.) while the fire is still small, or ideally, while it is still in the incipient stage. Fire detection and warning systems, utilizing sensitive heat, flame, smoke, and gas analyzers, provide the most rapid and reliable indication of a developing fire.

Jan 1, 1987

By E. J. Ostrowski

The Bureau of Mines experimental blast furnace, Bruceton, Pa., was operated to determine the feasibility of replacing part of the burden coke requirements with solid fuels injected directly into the smelting zone. This report describes preliminary experiments and information resulting from such an interchange. These experiments were made on an all-sinter burden, using two parts sinter to one part fuel. Anthracite fines were injected intermittently into the smelting zone of the furnace by compressed air through auxiliary tuyeres. The interval between injection periods ranged from 5 to 15 minutes. A maximum of 28 percent of the stock column coke bur-den was replaced. This percentage replacement caused furnace malfunction, but the overall percentage of these experiments indicated that 20 to 24 percent of the coke requirements could be replaced in this way. The metallurgical coke consumption was decreased by as much as 377 pounds (25.3 percent) per ton of pig metal produced. Buckwheat anthracite No.4 was used in this experiment; however, such solids as bituminous coal or coke fines also could be used. The frequency as well as the quantity of solid fuel injected has a direct bearing on furnace performance.

Jan 1, 1960

By H. R. O'Brien

"During the past year, the Pittsburgh experiment station of the Bureau of Mines has been investigating methods for the quantitative estimation of carbon monoxide in blood. This work was necessary because reliable methods of analysis are of the greatest importance in the bureau's research work on prevention and treatment of carbon monoxide poisoning among workers in mines and metallurgical plants. Two of the methods considered involve color comparisons. In one of these methods, differences in tint can be noted fairly readily, while in the other, they are much more difficult to detect. The latter, however, is otherwise considerably simpler. It was decided, therefore, in studying the possibilities of this second method, to use the most sensitive eyes in the laboratory force.Preliminary trials.The method under investigation was the Haldane carmine determination of carbon monoxide in blood. The plain oxyhamoglobin of the blood in dilute solution is a pale straw color, when exposed to carbon monoxide it becomes a cherry pink. In the analysis dilute indigo carmine is added to oxyhsmoglobin until the solution matches in tint the carbon monoxide hemoglobin. The eye wanted, then, was the one most sensitive to faint pinks. But just how to select the analyst was not clear At first the Williams test scale, used in the Navy, was considered, but on con¬sultation with Dr. L. L. Thurston, bead of the Department of Psychology at Carnegie Institute of Technology, the following procedure was adopted.Instead of standard tests made up of all colors, only those occurring in the analysis were used. Solutions were prepared of the two hemoglobins, from which twenty-four different pairs were made up and placed in test tubes like those expected to be used in the analysis. One of each pair differed from the other in percentage of carbon monoxide hemoglobin by amounts varying from 2-1/2 per cent to 20 per cent. Each pair was compared in a box built in our own shop. This was 20 inches long and 5 inches square in cross section. One end was covered with ground glass. Just inside this glass cover were provided two slots, each the width of the test tubes used. The tubes to be compared were dropped into these slots through two holes in the top of the box. The device was placed before a window away from the sun, and so arranged that the light conditions were the same on each slit or opening. The person to be tested was seated before the box, and as the two tubes were placed before him side by side, he marked whether A (left) or B (right) contained the more cherry pink. This procedure was continued till he had compared all the pairs."

Jul 1, 1921

By Oliver Bowles

"Properties and Uses.Iceland spar is a name given to a pure crystallized form of calcite (CaCo3) which is sufficiently transparent and free of defects to be used in the manufacture of optical instruments. While the actual requirements are small, the degree of purity and physical perfection demanded renders it somewhat difficult to obtain suitable material.The properties of value in Iceland spar are its transparency combined with double refraction. It is used in the manufacture of polarizing microscopes, saccharimeters, colorimeters and photometers. Its most important use is in the manufacture of Nicol prisms, which constitute an essential part of every polarizing microscope. The principle governing the construction of the Nicol prism is as follows:Ordinary light in passing through a crystal of calcite is resolved into two rays of plane polarized light vibrating in planes at right angles to each other and having different indices of refraction. Thus the two rays follow different paths through the crystal. The prism of Iceland spar is cut diagonally and cemented together again with a transparent cement having an index of refraction intermediate between the two rays passing through the prism. Canada balsam is employed for this purpose. The prism is cut at such an angle that the ray having the greatest index of refraction meets the surface of the balsam at an angle greater than the angle of total reflection, and it is thus deflected to the side of the prism, while the second ray passes through. Thus one of the rays is eliminated and polarized light vibrating in a single plane is obtained."

Apr 1, 1920

By A. L. Service

The four periods of test operation described in Report of Investigations 5219 indicated that planer mining of phosphate rock was feasible. Corrective measures proposed for design deficiencies indicated in test 4 had to be evaluated, however; and, before the attempt to design a prototype production model, it was considered advisable to test the original machine under more severe operating conditions. Planer A was modified, therefore, during the latter half of 1955, and one additional period of experimental operation was conducted in the Anderson mine of the Montana Phosphate Products Company near Garrison, Mont., during the first 4 months of 1956. Test 5 was made in a stope, where the phosphate bed had been offset in a number of places by minor faults. Considerable difficulty was found in negotiating the irregularities caused by these faults, and productionwise the test was not as successful as some of the previous ones. Information obtained, however, was valuable in designing model B.

Jan 1, 1959

By N. F. Le Jeuns

For a number of years the Bureau of Mines has conducted semi-annual surveys to determine the changes in motor gasoline being sold in the United States. It was pointed out in the previous survey that there was an apparent tendency toward greater uniformity in the character of gasoline marketed in the United States. This practically uniform tendency which continued from April, 1917 to January, 1923, has been interrupted in the, present survey, as shown by an examination of the column marked "Difference," as given in Table 1. The figures in this table were obtained by averaging the end points of the least volatile and most volatile samples of gasoline. For example, of 850 samples analyzed in 1919, the 10% ,(85 samples) having the highest end points and the 10% having the lowest end points mere grouped, and the end points of each group averaged. These averages are represented in the table as the "Maximum 10%" and the ?Minimum 10%? respectively. The same process was used on the other surveys.

Jan 1, 1923

Provide low-cost fire protection for big bulldozers. Approach A fire protection system, previously used on mobile logging equipment and adapted to surface coal augers, has now been adapted for use on large mining bulldozers. How It Works Heat sensors mounted in the engine compartment and hydraulic hose areas detect the fire, usually before the operator does. This causes the system to automatically discharge A-B-C class dry chemical extinguisher through a fixed piping system. The system can also be manually activated from either the opera-tor's cab or ground level. Location of the principal components of the system are shown in the drawing The heat sensors of the sys-tem consist of bimetallic strip switches which operate at about 10000F temperature. Switch operation results in release of compressed gas from a small storage cylinder. The gas expands to blow the dry chemicals out of the nozzles, in a spray that lasts about 15 seconds. The compressed gas used is usually nitrogen, although carbon dioxide is also used.

Jan 1, 1978

By Claude W. Sill

In the course of a series of investigations on vanadium deposits of the western United States, the Bureau of Mines collected many hundreds of samples for chemical analysis. As uranium is often associated with these vanadium minerals, they were also analyzed for uranium, which was pound to be absent in a large percentage of the samples. Since the usual methods for determining uranium are laborious and time-consuming it is very desirable to have some simple qualitative test that can be applied prior to a quantitative analysis to determine whether uranium is present or absent and thus save the time and expense of applying the quantitative analysis to the large proportion of samples containing no uranium. To be acceptable, the test should be specific for cranium, sensitive enough to detect small amounts of uranium, and. simple enough to make it worthwhile to apply. The available methods for detecting uranium lacked one or more of the desired characteristics. Eventually, however, a method was worked out that satisfied all the requirements. This method is probably more specific and sensitive than the usual qualitative methods for uranium, and its simplicity and speed of application make it ideal for testing samples prior to quantitative analysis.

Jan 1, 1945

By J. E. Chilton, Jr. Dubaniewicz

Many mines rely on toxic gas sensors to help maintain a safe and healthy work environment. This report describes a prototype monitoring system developed by the U.S. Bureau of Mines (USBM) that uses light to power and communicate with several remote toxic gas sensors. The design is based on state-of-the-art optical-to-electrical power converters, solid-state diode lasers, and fiber optics. This design overcomes several problems associated with conventional wire-based systems by providing complete electrical isolation between the remote sensors and the central monitor. The prototype performed well during a 2-week field trial in the USBM Pittsburgh Research Center Safety Research Coal Mine.

Jan 1, 1995

By Wm. W. Odell

A study of certain gas making and fuel problems peculiar to the gas industry of California has been made by the Bureau of Mines. The work was done at the request of, and in cooperation with The California Gas Research Council 2, for the purpose of obtaining basic information on the gas-making fuels available to California, and their applicability to the present and future needs of the gas industry in that State. The data obtained have been applied in outlining a construction program, and indicate the possibilities in efficiently utilizing fuels in making gas by other than the oil-gas process. This paper presents an outline of the study and a summary of the principal results obtained, with some of the more important conclusions and recommendations based on this data. Gas is produced in California by processes which are both unique and different from those common to other parts of the United States. The bulk of the manufactured gas is made in and distributed from two main districts which are centers of population - namely, the Los Angeles district and the San Francisco Bay district. The gas manufactured in the Bay district is, almost exclusively oil-gas, whereas that produced in the southern part of the State, where natural gas is available, is mostly mixed natural gas and reformed-gas, but oil-gas is the chief product when the supply of natural gas is inadequate. Practically all of the gas companies are equipped with oil-gas generating apparatus, and anticipate using it in the future. As the continued use of the oil-gas process to the exclusion of all other processes, depends upon a continued supply of oil at a low cost, and the prospect of obtaining such low-priced oil in the future is somewhat uncertain, the questions have arisen: What will the future gas-making process or processes be? When will it be necessary to make plans for the installation of different gas generating equipment, and what will that equipment comprise?

Jan 1, 1926

By R. M. Gammell

"INTRODUCTION The Farmer prospect was examined by W. R. Green, an engineer of the Bureau of Mines, in June 1944. As a result, studies of this property were included in a general preliminary investigation of the Etevens County lead-zinc deposits by the Bureau in 1945. The exploratory work was designed chiefly to supplement the surface examination by determining the nature of the mineralization below the zone of oxidization. The results of the small-scale diamond-drilling program undertaken at the property are presented in the following report.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization our resources to the end that they make the greatest possible contribution to security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work and prepares the filial report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

Mar 1, 1947

By Jr. Allan

"Although the advantages of large-capacity air receivers for underground mines are plainly evident from published information about various installations in the United States and abroad, details of their construction are not generally known in this country., Ordinary present-day air-compressor installations servicing mining machines are designed to supply air at a specified pressure in sufficient quantity to meet the peak demand of the mine,2/ although this demand may exist for only a few minutes out of 24 hours and, as usually happens, eventually exceeds the capacity of the compressor. Most of the receivers provided with these compressors (to a certain degree of standardi¬zation) are capable of storing a volume of air approximately equal to that compressed in 1 minute by the machine.3, 4/ As a result, during peak-load periods the compressor operates at full load capacity without maintaining kick-off pressure. At other periods of the work cycle, production of compressed air is intermittent.At least one large mine5/ has adopted large-capacity receivers to reduce wear on its air-compressing system caused by the sudden demand of peak loads. Under the old system, the compressors jumped suddenly from half speed to full speed; boilers furnishing steam to the compressors were taxed heavily to provide the increased requirements of power; and machines using the air, among which were four large hoists, were required to operate at 65 pounds per square inch rather than at the 90 pounds per square inch for which the compressors were regulated. Operation of air machines, especially drills, at pressures lower than those for which they were designed decreases their efficiency and increases maintenance costs. In addition, air that comes directly from the compressors has had little opportunity to cool and dry enroute.6./ As a result, quantities of compressor lubricant and water are carried into the machines that use the air. When expansion occurs in the cylinder or turbine of such engines, the temperature of the air drops, and this oil and water is precipitated. The water washes away lubricating oils in the machine, causing poor performance and high cost of maintenance; the compressor oil, in addition to being a poor lubricant for compresed-air engines, exerts a corrosive action on gaskets and rubber hoses.7/Reduction of peak demands on air compressors by large receivers lowers power costs by establishing more nearly constant load factors,8/ and in some cases by permitting the use of smaller compressor capacity.8,9/Load factor is the ratio of average demand to maximum demand; a low load factor costs money.10/Elimination of high-peak demands raises the load factor by making the average and the maximum demand more nearly equal. Further savings may be made possible by large receivers where their use permits charging to be done at night in regions having lower power rates during that period.11/Where ordinary receivers are used, compressor breakdowns cause immediate work stoppages in the mine owing to lack of air. Similarly, the capacity of a large receiver has been known to permit uninterrupted work in the mine until the compressors have been returned to service.9/Large-capacity receivers, either steel-tank or underground rock-chamber, offer a practical solution of many existing problems by providing a sufficient reserve of compressed air within the pressure range required for efficient operation of machines to level off peak demands on the compressor. The com¬pressors operate when the demand has reduced the pressure in the receiver below the regulating pressure and until all air used from the receiver has been replaced. It has been found possible in at least two mines,8.9/ one of which the author has visited, to entirely eliminate one compressor and to obtain more efficient performance from the remaining one by the construction of an underground coal-chamber receiver.8/"

Jan 1, 1950

By Wilbur I. Duvall

In this report, the Bureau of Mines presents a theoretical solution for the stresses and displacements in an infinite elastic plate containing a circular hole the boundary of which is loaded by applied radial stresses over four separated arcs. The problem solved is a two-dimensional approximation of the stresses and displacements developed by a large tunnel-boring machine anchored in a circular tunnel. Analysis of the solution shows that the tangential tensile stresses induced on the boundary of the circular opening can be minimized in the roof and maximized in the floor of the opening by proper spacing and loading of the four arcs.

Jan 1, 1967

By A. B. Hooker, E. J. Coggeshall

"INTRODUCTION Ignitions of gas at the coal face when a blast is fired electrically are often a tributed to the explosive; but sometimes the ignition cannot be explained satisfactorily in this way-in fact, ignitions have occurred when the detonator has failed explode.The possibility of such electrically by sparks from the blast between poorly insulated leading wires and detonator leg have been recognized. Several countries have provided safe types of single-shot blasting units; some have permitted the use of larger multiple-shot blasting units provided each unit is equipped with a time-limiting switch that prevents unnecessarily long application of voltage on the leading wires after the shot has occurred, the assumption being that the firing line will this be dead before damage to the wires and subsequent sparking can take place. An extensive research was made by a French commission relative to the characteristics of electric detonators and methods of firing. Along other tailings they investigated the probability of ignitions by sparks across the leading wired at the face, also the time and duration of the various events in blasting, such as ignition of the detonators, movement of the coal face, and application of firing current. They suggested, as a means of eliminating or reducing tilt possibility of gas ignitions from the blasting unit, that the timing switch of the blasting unit be designed to disconnect the blasting"

Oct 1, 1934

By Charles E. Whieldon

The importance of recovering more oil from known petroleum reserves has placed increased emphasis on the application of secondary-recovery methods. It is hoped that these reports will stimulate interest in improved waterflooding techniques, thereby discouraging premature abandonment of oil leases. A previously published report4/ described the highly successful results of waterflooding in the Weir sand in eastern Kentucky. A more recent report5/ evaluated the results of waterflooding in Roane County, W. Va. (See fig. 1.) Two waterflooding projects have been operated in Pleasants County, W. Va. (fig. 2), one by the Dearborn Oil & Gas Corp. in the Cow Run sand near Calcutta, McKim and Washington districts, and the other by George C. Schoonmaker in the Maxton sand at Bens Run, Union district. This report report describes the waterflood operation near Calcutta, W. Va.

Jan 1, 1960

By James J. Olson

The Bureau of Mines used micro fracture density analysis of quartz grains in thin sections and diametric pulse velocity measurements along preblast and postblast cores to determine the nature and extent of rock damage produced by small (0.25-,0.50-,1.0-, and 2.0-kg) charges of high intensity explosive (C-4) in granite. Pulse velocities from the postblast cores were significantly lower than velocities from the preblast cores and, with the core logs, provided clear identification of the upper and sometimes the lower limits of most severe damage. These zones ranged from about 1.68 ft for the 0.25-kg blast to 4.16 ft for the 2.0-kg blast. Microfracture densities from postblast cores were significantly higher and more variable than densities measured from preblast cores. The microfracture density measurements showed that microscopic damage was present far past the zones of most severe damage as delineated by the pulse velocity logs and core logs. An exponential relation-ship was observed between the micro fracture density levels and the charge weight.

Jan 1, 1973

Roof bolting is a slow, expensive, and absolutely necessary mining activity. Roof-bolting activities also account for the largest percentage of lost-time injuries in underground coal mines. Dull bits result in the application of excessive force, which bends drill steel; and changing starter and finisher steel was the most significant source of injuries associated with roof bolting. The tungsten carbide (WC) roof-bolt drill bits currently used in American, Canadian, and Australian coal mines are capable of drilling only one or two 4-ft holes and then they are resharpened once or twice to drill another one or two holes. Often, in medium-hard rock formations (sandstone), as many as 20 to 30 bits may be required to drill a single 4-ft hole. Objective To compare the performance, longevity, and cost of newly developed polycrystalline diamond compact (PDC) roof-bolt drill bits against WC bits. Research and Background Diamonds for industrial use have been scarce throughout history and continuous attempts have been made to produce synthetic diamonds. The first synthetic diamonds were manufactured in 1953. Economically produced synthetic diamonds are 1 to 10 µm in size, but in this size range, they are totally unsuitable for industrial applications. In 1972, General Electric Co. developed a process to sinter the artificially developed, minuscule diamond particles into usable products. In this process, several layers of diamond-particles-and cobalt mixture are overlaid on WC substrates and sintered at 2,350° F and 1,000,000 psi. The final product is known as PDC. Today, PDC's are available in many shapes, but their size is limited to 3/4 in, or less, in length or diameter, because pressures greater than 1,000,000 psi are required to manufacture larger PDC's. At present, diamond and PDC arc the hardest and strongest commercial materials available for wear surfaces. The PDC used in this study had a hardness 3.61 times greater than that of WC.

Jan 1, 1992

By R. V. Rahfuse

Noncaking 0- by 2 -inch subbituminous coal from New Mexico was gasified with air and steam at 205 prig using a stirred-bed producer to determine coal losses by entrainment in the gas for this low-sulfur, high-ash coal which contained 20 percent particles smaller than 1/16-inch sieve size. The use of fine-sized coal has particular importance because most production from mechanized mines is smaller than 2-inch size. This initial attempt showed technical feasibility for gasifying New Mexico subbituminous coal containing small-sized particles in fixed-bed producers without excessive coal loss by entrainment. Dust loss averaged about 2 percent of moisture-free coal, most of which was recovered from the gas. Ash clinkering was controlled by adding 1,010 lb/hr steam to reduce tempera¬tures in the combustion zone. Yield of low-Btu fuel gas, 150 Btu per scf, dry, amounted to 69,800 scfh from 1,490 lb/hr coal (as received) and 3,450 lb/hr air (dry).

Jan 1, 1974

By R. T. Johansen

The wettability of petroleum reservoir materials by water and crude oil has been recognized as an important factor in determining waterflood behavior. The problem of simulating and studying reservoir conditions and characteristics, to produce laboratory results congruous with field experience, has been examined by many methods. (1, 2, 3, 4).4/ The most generally accepted approach to this problem is determining wettability of the porous medium by imbibition methods; or, after solvent extraction, predetermining the wettability of the samples by coating the surface of the medium to render it preferentially oil-or water-wet (3, 5). The emphasis of wettability studies has been placed on the characteristics of the reservoir materials with little consideration being given to the fluids themselves. Therefore, the wetting tendencies of crude oils have been investigated by a recently developed method (6). Imbibition and the more general phenomena of capillary pressure are the most direct ways to measure wettability. The simplest type of capillary pressure observations involves the use of an interfacial-tension capillarimeter, which does not produce as separate values either interfacial tension or contact angle. Actually, these quantities do not have independent significance in reservoir engineering, and the property of wettability they are intended to evaluate is given, immediately by capillarimetric measurements.

Jan 1, 1961