Search Documents

To develop a business case that promotes adoption of noise controls by reducing barriers to industry acceptance and enhancing drivers that foster their implementation. Background Over 75% of the U.S. mining workforce is exposed to hazardous noise, putting them at risk of noise-induced hearing loss (NIHL). Consequently, coal miners suffer high rates of hearing impairment that increase to 70%-90% by retirement age. To address the noise problem for coal miners, researchers from the National Institute for Occupational Safety and Health (NIOSH) first determined that the continuous mining machine (CMM) ranked first among machines associated with reported coal noise overexposures. Further studies found that most CMM noise is generated by three component systems on the machine: dust collection, cutting, and conveying. Of these systems, the on-board chain conveyor was found to be a dominant noise source. Noise generated by the conveying system was addressed through the development of a urethane-coated flight bar chain. The coated chain, shown in Figure 1, has demonstrated an 8-hour time-weighted average (TWA) reduction of operator exposure by 3 dB(A). It has since been accepted by the Mine Safety and Health Administration (MSHA) as a "technologically achievable" noise control for CMM operators who are exposed to noise that exceeds the MSHA permissible exposure level. Having demonstrated the noise reduction performance of the coated chain, NIOSH has assembled information into a business case that can be used by operations considering adopting the chain at their worksite.

Dec 1, 2009

By A. C. Fieldner

The Bureau of Mines has recently conducted a study of results obtained in analyzing similar samples of coal and coke by 25 laboratories throughout then country, in comparison with results obtained in the Bureau's coal laboratory at Pittsburgh. The purpose of this work was primarily to obtain a comparison of the methods of coal analysis used by the laboratories of the American Gas Association. Therefore, four standard samples of coal end one of coke ware prepared in the Bureau of Mines coal laboratory at Pittsburgh, and portions sent to each laboratory. At the same time, a like number of standard samples were submitted to 12 commercial laboratories rot affiliated with the Association, for the purpose of comparing their analyses with the results is obtained by the U. S. Bureau of Mines and the American Gas Association. Tire comparison is based on the average of 24 analyses by the Bureau of Mines on each kind of coal, and the accompanying curves show the deviation from this average analysis, together with deviations from the check limits of the American Society for Testing Materials.

Jan 1, 1923

By Oliver Bowles

Wire saws have been used for many years in European travertine, marble, and slate quarries. This method of sawing found very limited use in America until 1927 when it was accepted as standard equipment in elate quarries in Pennsylvania where it has been remarkably successful. Details of its operation in slate have been published in a recent bureau report.3 The very limited extent to which the wire saw has been employed in limestone and marble quarries in the United States and the seeming lack of interest even in experimental work to determine its advantages are difficult to explain in vied of its wide use in cutting similar rocks in Europe and its unquestionable advantages in sewing slate in America. In order to encourage improvement in quarry practice the United States Bureau of Mines has endeavored to obtain information as to the extent to which wire saws are used in Europe together with data on the rate and cost of sawing. The information at hand is by no means complete either in territory covered or in details of operation; it nevertheless brings out certain significant features that may be of interest and advantage to quarrymen in the United States.

Jan 1, 1931

By Daryl E. Radcliffe

The Bureau of Mines studied the displacement of the roof in a portion of the Bear coal mine near Somerset, Colo, Horizontal-and vertical-displacement gages were installed in a five-entry section during normal room-and-pillar mining procedures. Monitoring of the roof continued until this section was mined out. Displacement measurements in combination with known time lapses between mining and bolting operations indicate that once support is achieved, the length of unsupported time does not appear to affect long-term roof stability in the mine under investigation.

Jan 1, 1978

By Jeffrey B. Osmint

The Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1991

New Continuous Personal Dust Monitors (CPDM) submitted to NIOSH for approval to sample coal mine dust must accurately measure respirable coal mine dust in mine environments. There are two steps in the process which may be done in any order. The manufacturer is required to submit the results of a comparative underground coal mine dust sampling study, where the candidate CPDM is compared to an approved coal mine dust sampling device (currently the Coal Mine Dust Personal Sampling Unit (CMDPSU)). This testing shall follow the guidelines outlined below and shall demonstrate through weighted regression analysis that the mean coefficient of variation with bias correction is equal to or less than 12.8%. The other step involves laboratory testing to determine the electronic and environmental stability. This testing must be conducted by a private, commercial, academic or other laboratory approved by NIOSH.

Jan 1, 2009

By R. R. Sayers

The terms "sanitation and }\Vgienen are often used interchangeably, but it is more "' usual to apply ttsani tat ion'' to th environment or surroundings, and nr.ygieneto the iiiividual, The subject,. h9wever, is so broad that only a few of the phases of sanitation will be di.acusae in ·this paper, vmile the various Fsea of hyg:tene will be deferred for later consideration. One of the bes.t .iaf ini tions of sanitation that I have hearci was given by ur. L. L • Lumsden, of the U, S. Public Heal th Service, who state.d that "'sanitation is t-he c.oir .. 'Don-sens$ application of the principles of cleanliness,

Aug 1, 1922

By Harold C. Pierce

"INTRODUCTION During the years 1941 to 1945, the United States produced less than one-half of one percent of all primary nickel, whereas the nation's consumption of the metal amounted to nearly three-fourths of the world's supply. Although postwar nickel consumption probably will be less than wartime consumption, trade- estimates for the next 10 years are well above the average established during the 1930-1940 decade. The greatest consumption is expected in nickel alloys, particularly nickel-alloy steels. 3/ The greater use of nickel cast irons and nickel-clad metals also signifies an expanding nickel market. In anticipation of the postwar demand for nickel, and realizing the seriousness of the ""have not"" position of the United States with respect to this metal, the Bureau of Mines, sent an engineer 4/ into the lower Copper River region of Alaska during the summer of 1944 to investigate the nickel deposits near the head of Canyon Creek. Samples from the Spirit Mountain nickel prospect were sufficiently encouraging to justify more intensive exploration. As a result, a program of surface trenching, systematic sampling, and detailed mapping of the property was adopted and directed by a Bureau of Mines engineer 5/ in the summer of 1945."

Aug 1, 1946

By Richard Havens

Samples of low-grade oxide manganese ores were procured from two southern Utah properties by examining engineers of the Bureau of Mines during an investigation of manganese mineral deposits of continental United States. A 2-ton lot of ore was obtained from the Blackbird group of mining claims in Paiute County, 11 miles southeast of Marysvale, Utah. The deposit was described as an intrusive sheet or sill of altered brecciated rhyolite cemented together by manganese oxide minerals. A 2-ton sample from the Black John property, situated 32 miles northeast of Kanab, Kane County, Utah, was taken from open cuts on the vein. The blanket-type vein deposit consisted of nodules and streaks of manganese imbedded in compact gray clay.

Jan 1, 1949

By R. H. Sprute

The Federal Bureau of Mines performed laboratory tests using direct current to dewater and densify fine-grained coal sludge in order to alleviate disposal problems and lead to recovery of high energy value often present in this waste. The laboratory tests described in the main body of the report were performed on thickened underflow (no flucculant added) from a northern Appalachian coal preparation plant. Solids in this slurry was very fine with 65 percent of the particles less than 0.1 mm in diameter. A variety of application procedures tested is exemplified by a test in which a soupy slurry (55 percent dry-weight moisture content) was converted into a firm dense material with a 20-percent dry-weight moisture content. These results were achieved in 3 hours with current density of 3.7 amp/ft2 and a power expenditure of 35 kwhr/yd3. The treated material has an average heating value of 10,400 Btu/lb. Varying current density, electrode configuration, and placement depth makes application of the treatment flexible. Two other types of sludge were tested briefly--thickener underflow from a southern Appalachian coal preparation plant with flocculant added, and sludge from an acid mine drainage treatment plant. The underflow responded well to the treatment, but response of the sludge from the acid mine drainage treatment plant was poor.

Jan 1, 1976

By F. W. Cox

Exhaust emissions were measured from 25 aircraft turbine engines using Jet A fuel. Analytical apparatus, procedures, and results are described. Carbon monoxide, carbon dioxide, nitric oxide, nitrogen dioxide, and aldehydes were measured at engine operating modes representing power levels used in airline operation. Carbon monoxide, hydrocarbon, and aldehyde emissions were highest at idle and lowest at takeoff; oxides of nitrogen were lowest at idle and highest at takeoff. Of the total oxides of nitrogen emitted, nitrogen dioxide constituted from 10 to 100 pct, depending on the exhaust gas temperature. Engines retrofitted with smoke-reducing burner cans produced less carbon monoxide, hydrocarbon, and aldehyde emissions, and slightly more oxides of nitrogen then engines with standard burner cans.

Jan 1, 1972

By Frank K. McIntosh

The Wood mine area was investigated by the Bureau of Mines in -1941 by a magnetic survey and a gravitational survey. Surface trenches were excavated, and diamond-drill holes were bored at the strongest anomalies developed in common by the two surveys. In the last century', several widely separated bodies of chromite with some magnetite had been exploited in a 'serpentine belt near its contact with schist. At one time this district held a virtual monopoly on the production of chromite. Known ore bodies now are exhausted. Owing to the relatively high specific gravity of chromate compared to normal rocks, a gravitational survey was run to determine which magnetic anomalies were worthy of diamond drilling. Linear feet of trenching totaled 1,710 feet. Ten holes were diamond drilled, which totaled 2,272 feet. The log of the drilling is shown in the text in a tabulation of drill-hole data.

Jan 1, 1948

By Joseph A. DeCarlo

This publication presents a tabulation of oven-and beehive-coke plants in the United States as well as pertinent statistical data on the number, capacity, kind, and condition of the ovens. Coke is an essential raw material in pig-iron production and the coal-chemical materials produced during the coking process are used to manufacture fertilizers, paints, plastics, synthetic rubber, explosives, detergents, nylon, pharmaceuticals; dyes, and many other products necessary to the high standard of living in this country. In table 1 the oven-coke plants in the United States on December 31, 1959, are listed. This shows the name and address of the company, location of the plant, classification or type of ownership, number and type of ovens, annual coke capacity, and the coal-chemical materials produced. The "furnace" plants I are those owned by iron and steel companies and most of them are integrated with blast furnaces to facilitate transportation of raw materials for steel making. Furnace plants represented 87 percent of the total coking capacity and their average annual capacity was 1. 3 million tons. The "merchant" plants are those associated with chemical companies, gas utilities, as well as those that produce metallurgical, industrial, and residential-heating grades of coke and coal-chemical materials for sale on the open market. These coke plants are smaller than furnace plants and in 1959 their average coke capacity was only 520 thousand tons annually. On December 3l, 1959, there were 54 furnace and 20 merchant oven-coke plants in existence in the United States.

Jan 1, 1960

By C. A. Allen

"The problem of signaling to the hoisting engineer from a moving cage in the shaft has been considered by many mine operators for a number of years. There are several methods in use in different mining districts, and so far as the writer is aware they have been further developed in Utah than in any other state. The latest installations are of interest because they use a very low-voltage circuit for the shaft wires and also because the wiring can be so arranged that the hoist can be stopped from the cage, if so desired.The first installation in Utah was in the shaft of the Centennial-Eureka mine under the management of C. E. Allen. It was placed in operation in the summer of 1899, end has been in continuous and satisfactory operation for 21 years. The arrangement consists or two bare wires down the shaft carrying a current at 60 volts potential, with a device on the cage for making connection between the two wires. This device is simply a short piece of wire which is thoroughly insulated from the cage and is operated by a short lever. Whenever the cage rider wishes to signal the engineer he pulls down the lever, forcing the short wire out against the two bare wires, thus making a circuit which rings the bell in the hoist-room. A similar device was planned in the Grand Central shaft at Mammoth, Utah, but was later abandoned. The cause of failure was reported to be that the shaft was very wet."

Jun 1, 1920

By John Zetterstrom

Increased activity in the beneficiation of taconite, particularly the magnetic variety, has shown the need for more information on the rate of oxidation of magnetite to hematite. This oxidation occurs in the pelletizing step of the beneficiation process. Magnetic taconite is an intimate association of magnetite and a siliceous gangue. It must be ground to approximately 70 to 30 percent minus 325 mesh to liberate the magnetite from the gangue. With sufficient liberation, magnetic concentration will yield a product high enough in iron and low enough in silica for blast-furnace use. The magnetic concentrate must be agglomerated before it can be used in a blast furnace. Agglomeration is the general term applied to all methods of compacting or consolidating fine iron-oxide materials, sintering and pelletizing being the two most common methods. Sintering is clone on a Dwight-Lloyd or Greenawalt sintering machine. Pelletizing consists of balling fine, moist oxide in a rotating drum, followed by baking at .a temperature below that of incipient fusion to develop a permanent bond within each pellet. The magnetic concentrate from taconite is too fine for good sintering practice but fine enough for good pelletizing practice.

Jan 1, 1950

By Andrew B. Cecala, Edward D. Thimons

"The Bureau of Mines has recorded a number of different background dust sources that significantly contaminated the air breathed by bag machine operators. These background sources, observed at five different plants over the past 2 years, can expose bag machine operators to more significant dust concentrations than the filling process itself. To keep bag operator exposure within acceptable dust levels established by the Mine Safety and Health Administration, U.S. Department of Labor, the significance of these background sources must be realized, and the sources must be identified and controlled. The purpose of this work is to identify common background dust sources and show the significant effects that they have on the bag operator's overall dust exposure. INTRODUCTIONThe purpose of this report is to identify some common background dust sources in and around the bag-filling area. Although these background dust sources are of ten unrecognized, they can be more significant sources of contamination than the dust generated from the bagging process.The bagging of mineral products into 50- and 100-lb paper bags is common throughout the entire mineral processing industry. Bagging is performed by a bag operator who sits in front of a two- or four-station fill machine. The bagger's function is to attach empty bags to the fill nozzles as filled bags are ejected from the machine. If the product being bagged is extremely fine (smaller than 200 mesh), the bag operator's dust exposure is usually one of the highest in the plant.The bag operator is exposed to two primary dust sources. The first is product blowback during the bag-filling cycle. This occurs as excess pressure is released from around the fill nozzle during filling. As the excess air forces its way out of the bag, product is forced out with it. This blowback of product leaving the bag creates a considerable amount of dust. The second major source is the ""rooster tail"" of product thrown from the bag valve and fill nozzle as the bag is ejected from the fill machine. Since the bag is pressurized as it leaves the machine, product spews out of the valve for a few seconds."

Jan 1, 1986

By Linda L. Chasko, Charles P. Lazzara, Ronald S. (deceased) Conti, William J. Wiehagen

Fire has long been a concern for underground mine workers. A mine fire can occur at any time and can result in a partial or total evacuation of mine personnel and the loss of lives. Fires can grow rapidly. Time is the critical element. Prompt detection, timely and accurate warnings to those potentially affected, and a proficient response by underground miners can have a tremendous impact on the social and economic consequence of a small underground fire. Fire preparedness and response have components of technology and people. These components can work synergistically to reduce the time it takes to bring the system back in balance. This report deals with the preparedness of miners to respond to underground mine fires. It is intended to aid the mining industry in understanding the various roles of emergency responders and the training techniques used to increase their skill levels. The report also presents a technology overview to assist in effective response to mine fires.

Jan 12, 2005

Pillars with width-to-height ratios of less than 1.0 are frequently created in underground hard rock mines. The strength of slender pillars can be estimated using empirically developed equations. However, the equations can provide variable results when the width-to-height ratios approach 0.5. This paper investigates some of the issues affecting pillar strength at low width-to-height ratios in hard brittle rock. The investigation includes an evaluation of empirical pillar strength data presented in the literature and observations of pillar performance in underground limestone mines in the eastern United States, supplemented by numerical modeling in which failure processes and sensitivity of slender pillars to variations in rock mass properties are evaluated. The results showed that the strength of slender pillars is more variable than that of wider pillars. The numerical model results demonstrated the increasing role of brittle rock failure in slender pillar strength. The absence of confinement in slender pillars can result in a fully brittle failure process, while wider pillars, fail in a combined brittle and shearing mode. The onset of spalling in slender pillars occurs at or near the ultimate strength, while this is not the case for wider pillars. Slender pillars are shown to be more sensitive to the presence of discontinuities than wider pillars, which can partly explain the increased variability of slender pillar strength. Two examples are presented that illustrate failure initiation by brittle spalling and the sensitivity of slender pillars to the presence of discontinuities.

By W. M. Weigel

"Sand is one of the most useful and, fortunately, one of the most common mineral commodities. By far the largest proportion of the production is used in construction, including all forms of building, concrete and paving, sand for this purpose is produced in every State in appreciable amounts. Excluding send used for railroad ballast, molding sand stands not in tonnage produced, followed by glass sand.Special sands. In addition to the above, many grades of sands, with special characteristics, are used in industrial processes, and may be classed in a group as ""special sends"". This includes filter sand, sand blast sand, engine sand, abrasive send, fire or furnace send, special flooring sand, roofing sand used as a finish for prepared roofings and pottery placing sand sand blast and filter sand have been discussed in previous reports.Very few send companies depend upon the production of any one of these grades, as their source of revenue. They are generally especially prepared from the bank run of sand by different methods of screening or washing, or may, in some instances, be by-products from the production of ether grades. Many companies not now producing them might be able to supply local demands by a slight addition to their plant. In nearly all cases, they command a better price than the usual grades of building sand.Definitions and Properties.Engine sand, or traction sand, as it is sometimes called, is used to prevent the slipping of the driving wheels of locomotives, or other self-propelled vehicles, on wet or slippery rails. Its greatest use is, of course, for railroad locomotives, but street cars use considerable amounts and mine locomotives require its use. As the send must be very dry when used, most consumers have their can drying equipment, so it is often shipped damp, with its natural water content on what resulting from washing by the producer."

Oct 1, 1924

By R. L. Montgomery

Heats of solution of cerium metal and cerium (III) chloride in hydrochloric acid were measured. The standard heat of formation of the aqueous cerium (III) ion at 25° C is -166.1 ± 0.3 kcal/mole. Heats of solution of cerium (III) chloride in hydrochloric acid are consistent with the existence of a complex CeC1++ having a stability constant of 1 and a heat of complexing of 5.4 kcal/mole.

Jan 1, 1962