Search Documents

By Eugene T. Sheridan

The annual survey of the fuel-briquet industry by the Bureau of Mines, United States Department of the Interior, revealed that 21 fuel-briquet plants in 11 States were in operation and reported production in 1956. The demand for fuel briquets in the United States has gradually declined since 1948, and the number of operating plants has decreased from 36 to 21. Also, the annual productive capacity of the industry has decreased, although not a proportionate amount because most of the plants that were abandoned were small and in most instances had a designed capacity of less than 25,000 tons per year. In 1956 the 21 active plants had an annual capacity of 3.7 million tons (table 2), which was only 20 percent less than the total capacity of the 36 plants in 1948. This indicates that most of the larger plants have remained active, even though operating at reduced rates, and the average capacity of the industry has increased from 130,000 tons per plant in 1948 to 177,000 tons in 1956. Since 1948 operating rates have decreased from 67 percent to 41 percent of annual capacity.

Jan 1, 1958

By A. B. Coates

During the last three years the use of ethylene glycol dinitrate4 (E.G.D.) as at low-freeze (L.F.) agent in place of nitropolyglycerin has become common in the manufacture of explosives of the dynamite type. The usual proportion of D. G. D. in the explosive "oil" is 25 per cent; the remainder, 75 per cant, is regular nitroglycerin. These proportions were probably selected as a continuation of the practice of 25 per cent nitropolyglycerin and 75 per cent regular nitroglycerin.

Jan 1, 1929

By John C. Franklin

A radon survey was made at five different locations in the Twilight mine near Uravan, Colo., to determine chances in radon concentrations in an inactive mine. Data were taken with a continuous monitor set for 1-minute count periods and readings were taken 24 hours a day for 9 days. The 12 readings per station each hour accurately showed how t w radon concentration varied during the day. From the data collected from the intake portal to station 4, the average radon emanation rate was estimated at 18 picocuries per second per square foot (pCi/sec/ft3). A daily cycle in radon concentration was detected that apparently was related to barometric pressure change.

Jan 1, 1976

By J. P. Walsted

The lack of an iron-smelting industry in the Pacific Northwest places the ferrous metals industries under an economic handicap. No iron-smelting enterprises, now dormant, had been operated successfully. Iron made at both of hoes installations proved to be satisfactory for normal pig-iron uses. Electric power and reductants acre available in the area. Power from the dames now completed and. those being constructed insures present and future needs for basic industries. Subbituminous coal, close to the main supply of iron ore, insures ample reluctant for all smelting requirements.

Jan 1, 1954

By N. L. Wimmler

"INRODUCTIONSedimentary deposits of titaniferrous magnetite occur at various localities in the eastern foothills of the Teton Ranse in Deer Lodge County, Mont. The Choteau deposit was examined by a Bureau of Mines engineer in August 1942. An exploration project was recommended.Core drilling exploration was begun in June 1945; it was concluded in August 1945, Seventy-six holes were drilled. This report presents the data obtained by the Bureau of Mines exploration.ACKNOWLEDGMENTIn its program of exploration of mineral, deposits, the Bureau of Mines has as its primary objective, the more effective utilization of our mineral resources to the end that they make the greatest possible contri¬bution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, Chief, conducts preliminary examination, performs the actual exploratory work, and prepares the final, report. The. Metallurgical Branch, R. G. Knickerbocker, Chief, analyzes samples and performs beneficiation tests. Both of these branches are under the supervision of Dr. R. S. Dean, Assistant-Director. The field work was supervised by Earshel W. Newman, engineer in charge of the Helena Field Office. D. B. Hoiekvam was the project engineer; he provided most of the data used in the preparation of this report."

Dec 1, 1946

By R. W. Holliday

To determine the copper and nickel content of reported ore occurrences in the Chippewa mine near Rockmont, Douglas County, Wis., the Bureau of Mines reopened and sampled the old shaft and workings during the summer and fall of 1953. Occurrences of native copper near Rockmont and others near Gordon, also in Douglas County, Wis., are in lava flows, which extend from the Keweenaw Peninsula of Upper Michigan southwest across Wisconsin and into Minnesota. Sporadic attempts have been made to find additional economic copper deposits in these flows since profitable mines were developed in Upper Michigan nearly 100 years ago. The Rockmont and Gordon areas were explored extensively more than 50 years ago. More recently, from August 1944 to duly 1945, an occurrence near Gordon was investigated by the Bureau.2/

Jan 1, 1955

By G. A. Howes

This is one of a series of circulars dealing with the cost of equipping and developing mining properties in the United States and Canada, prepared and published by the Bureau of Mines in cooperation with various mining and exploration companies. This group of circulars is designed to supplement an earlier series which covered the methods and costs of mining and milling at a large number of producing properties. ACKNOWLEDGMENTS The authors desire to thank Robert A. Bryce, president of Macassa Mines (Ltd.), for permission to use the data presented in this paper, and to acknowledge the cooperation of A. J. Keast, under whose direction as manager the plant was installed and equipped and the shaft was sunk to a depth of approximately 2,000 feet.

Jan 1, 1932

By R. J. Fantel

To determine the availability of phosphate rock from domestic re- sources, the Bureau of Mines evaluated the potential production of phosphate rock from the demonstrated resources of 130 mines and deposits. The evaluation included an estimation of resources, engineering methods, and capital and operating costs, and an economic analysis to determine each operation's average total cost of production over the life of the mine, including a 15-pct discounted-cash-flow rate of return on all investments. Quantified but not evaluated in this report are substantial phosphate resources at the inferred and hypothetical resource levels. The 130 mines and deposits contain 6.4 billion tons of recoverable phosphate rock product, about 20 pct from producing mines. At total production costs of under $30 per ton in January 1981 dollars, about 1.3 billion tons of phosphate rock product is potentially available, over 90 pct from producing mines. This study suggests that production from low- cost, high-grade phosphate mines now in operation will decline during the next decade, and new higher cost, Lower grade mines will have to be developed to satisfy demand into the next century, In addition to the demonstrated resources evaluated in this study, 7 billion tons of inferred-level and 24 billion tans of hypothetical- level phosphate rock are potentially recoverable, which, in part, includes material containing high amounts of magnesium, Much of this material could likely become available in the near future.

Jan 1, 1983

By D. B. Gawthrop, A. Taylor, G. St. J. Ferrott

"This paper presents data obtained as part of an investigation of the explosive properties of ammonium nitrate. During the course of the work: it was found desirable to investigate the sensitizing action of nitrostarch in mixtures of ammonium nitrate containing low percentages of this material. Data were derived as to the sensitivity to decomposition by heat and the completeness of detonation and,of detonation of straight ammonium nitrate, as compared with ammonium nitrate-nitrostrarch mixtures containing 1 to 10 per cent of nitrostarch.The ammonium nitrate was a sample of coated material obtained from the salvage of amatol shells. Its analysis was as follows:"

Feb 1, 1930

By Nabil A. Bibawy

An improved method for preparing gravimetric standard gas mixtures of helium-4 in nitrogen has been developed by the U.S. Bureau of Mines. A single-pan 12-kg analytical balance that has a sensitivity of 3 mg is used to prepare the mixture. The balance will accommodate a cylinder having a volume of approximately 4 L that weighs approximately 5 kg. The method has been improved to a precision of ±O.04 pct by performing four successive dilutions, by improved handling of gases in the manifold, and by using an improved analytical method to select high-purity gases.

Jan 1, 1990

By J. W. Stevenson

The Bureau of Mines investigated the influence that atmospheric pressure changes exert in a gassy coal mil on a ventilating air current with a system of bleeder entries. During the season when abnormal barometric fluctuations usually occur, recording instruments monitored the air current ventilating an active coal-producing area. It HL he rate of coal production caused a more significant change in methane concentration than did barometric change. The hazard that accompanies methane release due to expansion of the gob gases during atmospheric lows was minimized by the effective bleeder system.

Jan 1, 1966

By J. M. Singer

The objective of this investigation was to determine minimum air velocities and entrainment rates for coal and rock dust dispersion in wind tunnel experiments under conditions that simulate dispersion from surfaces in coal mines where airflows are induced by weak gas explosions. Dust deposits were bed-or ridge-shaped; particle sizes were 6 to 80 microns (cohesive deposits) or 100 to 150 microns (free-flowing deposits); and wind tunnels were 7.62 cm wide by 5.08 cm high by 300 cm long, and 2.4 m wide by 1.5 m high by 215 m long. The investigation showed that minimum air velocities (directed at mid-height) of separate, layered, or mixed piles of coal dust and rock dust were within the range 5 to 30 m/sec, independent of size of wind tunnel. This finding considerably facilitates scaling of data to mine-size passageways. Free-flowing deposits dispersed relatively slowly by single-particle detachment; cohesive dusts dispersed faster by the breaking and lifting of large clumps along weak failure flames; particle dispersion occurred in flight. Layered or mixed deposits of coal and rock dust did not disperse selectively. Semiempirical expressions were derived relating minimum air velocities and dispersion rates to dust-pile geometry, cohesion, porosity, and bulk density.

Jan 1, 1972

By J. G. Stuart, A. W. Cipkins, R. H. Thompson

Preliminary safe distances for blasting wiring from typical electromagnetic sources are presented. The distances are for underground coal mines and electromagnetic sources in the frequency range below 10 MHz. The distances are based on measurements performed at 3 locations in each of 3 coal mines. The measurement apparatus, measurement procedure, measurement results and the rationale used in the calculation of the safe distances are all described. The safe distances presented are dependent on the measurement results and their interpretation. More measurements are clearly necessary to establish the validity of the suggested distances.

Jan 1, 1985

By John D. Bardill

This report covers the magnetic survey in the Redford-Clayburg area , which was part of a general survey of magnetite deposits in New York started in 1943 . Other areas being surveyed include the Star Lake district , St. Lawrence County; Russia Station district , Clinton County; Brewster district , Putnam County; and the Sterling district , Orange County. Only a relatively small portion of the area was covered by reconnaissance and detailed surveys . Results were promising enough to warrant additional work. Magnetic surveys of this type serve as a basis for selecting areas for diamond drilling by the Bureau of lines .

Jan 1, 1947

By D. H. Baker

THIS REPORT presents the technique and equipment used in determining the hardness of titanium sponge. Detailed descriptions are given of the methods used in preparing test samples for chemical analysis and hardness testing, the method of melting and surfacing test ingots, and the technique of reading Brinell-hardness impressions. The arc-melting furnace described, for which engineering drawings are included, will produce from 70 to 90 double-melted buttons each 8 hours of operation. Experimental data are also presented depicting the effect on hardness of the methods of surfacing specimens, temperature of test specimens, and the effect of time at test load. These data show that surfacing of the specimen involves no critical machining operations but that the test surface must be paralleled by a relatively flat surface for contact with the anvil of the Brinell tester. The heating of a specimen to 150° C. during surfacing does not materially affect the results if the ingot is cooled to room temperature before the hardness impressions are made. The optimum time at load appears to be approximately 30 seconds, but load times of as much as 1/ ½ minutes will not cause major errors.

Jan 1, 1959

By W. P. Diamond, B. M. Bench, C. M. McCulloch

This Bureau of Mines report describes photolineaments obtained from stereoscopic examination of vertical aerial photographs and by the Ronchi grating study of aerial photoindex sheets. The photolineaments are compared with the trends of oriented fracture systems procured by measuring the compass direction of joints in bedrock. The relative reliability of the methods is shown, and the results are presented in graphical, tabular, and written form. Analyses of field measurements of strikes of bedrock joints in the project area indicate for the most part two intersecting sets of major joints oriented N 76° W - N 15° E, and N 57° W - N 27° E. The analyses of lineaments determined by stereoscopic examination of aerial photographs show dominant trends of lineament zones of weakness to be an average of N 65° W - N 20°E. Analysis of lineaments found by Ronchi grid viewing of aerial photoindex sheets indicate dominant trends of N 70° W - N 27° E. The three methods give similar findings and verify the work of previous authors. The Ronchi grid method is a useful guide, but it cannot be substituted for the two more painstaking methods.

Jan 1, 1977

By L. B. Berger

In this investigation, the ampoule type of carbon-monoxide (CO) detector which is manufactured under license of U. S. Patent 1,644,014 (October 4, 1927) was tested for sensitivity and reliability. This detector was devised primarily for examining the air of manholes and sewers for possible dangerous contamination with CO before workmen enter these places, but due to the simplicity of the device it may have a more general usage for examination of atmospheres which are known or suspected, to be contaminated with CO. Some of the suggested uses are the examination of the air in garages, tunnels, mines, around blast furnaces, gas plants, and in the home.

Jan 1, 1930

By Harry Freund, Kenneth H. Hammill, Francis C. Bissonnette

"Gallic acid is a sensitive, stable, colorimetric reagent for the determination of tantalum in the range of 2 to 40 µ g.Ta/ml. The method consists of the fusion of tantalum oxide with potassium pyrosulfate and solution of the cooled melt in saturated ammonium oxalate, followed by development of a yellow complex with an ethanolic solution of gallic acid. The tantalum-gallic acid complex absorbs over a broad region in the blue and near ultraviolet. Adverse effects due to interfering ions and solution conditions, such as oxalate concentration and pH, can be minimized by a suitable choice of wave length.by a suitable choice of wave length.A new and sensitive colorimetric method is provided that has been used successfully at the Northwest Electrodevelopment Laboratory of the Federal Bureau of Mines for determining minor amounts of tantalum.INTRODUCTIONThe development of corrosion-resistant alloys at the Northwest Electrodevelopment Laboratory prompted a review of the analytical chemistry of columbium (niobium) and tantahnn. Not only are these elements difficult to determine in small amounts, but tantalum especially lacks both sensitive and characteristic color reactions. Various phenolic compounds have been suggested as colorimetric reagents for tantalum, Quentin and Wagner (10, p. 24B) 1/ recommend the use of tannin. The use of pyrogallol was suggested originally by Krivoshlykov (6, pp. 59-60), whose method recently has been subject to a number of modifications (3, pp. 249-254; 5, pp. 1340-1344; 1, pp. 1803-18oi; 4, pp. 345-350). The yellow coloration produced by pyrocatechol in an oxalate solution containing tantalum may also be used to estimate tantalum ( 11, pp, ll-1-4-148) . The use of hydrogen peroxide has been recommended also (7, pp. 164-165; 9, pp. 926-931).Aside from a lack of specificity and sensitivity, the major failing of phenolic reagents is their susceptibility to air oxidation. The oxidation products are highly colored and absorb in the same spectral region as the tantalum complex. Holding reductants are not completely satisfactory in minimizing this effect. Increasing the acidity, while retarding the oxidation, has an adverse effect on the tantalum sensitivity."

Sep 1, 1956

By R. L. Hopkins, H. T. Rall

A continuous method has been developed for preparing thiolacetic acid . Acetic anhydride and hydrogen sulfide are passed concurrently over an amine ion- exchange resin , under 20 - psi pressure . The thiolacetic acid , a product of the reaction , is flashed continuously from the crude reaction mixture and is purified by fractional distillation . The yield of thiolacetic acid is in excess of 80 percent based on the acetic anhydride charged . INTRODUCTION In the synthesis of reference compounds needed in the identification of sulfur compounds in petroleum , thiolacetic acid has become an important reagent because of its use in the synthesis of thiols by addition to appropriate olefins : R - CH = CH₂ + CH3 - COSH R- CH2 - CH2 - S - COCH R - CH2 - CH₂ - SH + CH3COONa NaOH (1 ) The commonly used procedures for its preparation , as described by Clark and Hartman (1 )4 and by Ellingboe (2 ) , are based on the batchwise reaction of acetic anhydride with hydrogen sulfide :

Jan 1, 1964

By Robert F. Holub

The U.S. Bureau of Mines (USBM) has tested a personal dosimeter for measuring radon decay products that is manufactured by Tom Scurry Associates. The tests were made to determine the accuracy of the dosimeter system for record keeping of radiation exposures to radon decay products encountered in mining. The radioactivity-detecting head is based on a design developed by the USBM, and the associated air pump was developed by the manufacturer. The dosimeter system was tested in the USBM radon chamber. The detecting head uses CaF:Dy thermoluminescent phosphors and is mounted on a self-regulating air pump. Batteries supply power sufficient for an 8-h shift. The dosimeter system is worn on the miner's belt. Dosimeter calibration tests were performed by the USBM. In addition, the pumps were tested and evaluated under continuous flow conditions. The results of these tests indicate that the Tom Scurry Associates Model DOSI600 dosimeter is suitable for general use in mines where record keeping for natural radiation exposure is required.

Jan 1, 1995