Search Documents

By Paul R. Amyotte, Omotayo Kalejaiye, Kenneth L. Cashdollar, Michael J. Pegg

The Siwek 20-L chamber is widely used throughout the world to evaluate the explosibility of dusts. This research evaluated the quality of dust dispersion in the Siwek 20-L chamber using Pittsburgh coal, Gilsonite, and purple K dusts. A Pittsburgh Research Laboratory (PRL) optical dust probe was used to measure optical transmittance through the dust cloud at various locations within the chamber. A total of 540 tests were performed, with triplicate tests at five nominal dust concentrations and six locations. The two standard dispersion nozzles (rebound and perforated annular nozzle) were compared. The transmissions corresponding to the normal ignition delay period were used to: (a) determine variations in spatial uniformity of dispersion obtained with both nozzles; (b) make comparisons between the experimental transmission data and those calculated from theory for the three dusts; and (c) make comparisons with transmission data measured in the PRI, 20-L and Fike 1 -m3 dust explosion chambers. The uniformity of dispersion for the three dusts was similar with both nozzles, despite the differences in nozzle geometry and mode of operation. Transmission data of the three dusts were all significantly lower than those calculated from theory. This was discovered to be, in part, due to significant reduction in particle size that occurred during dispersion. By measuring particle sizes before and after dispersion, values of 60%, 50%, and 20% reduction in particle size (based on the surface weighted mean diameter) were obtained for Pittsburgh coal, Gilsonite, and purple K, respectively. Transmission data from the PRL 20-L, Fike 1 -m3 and the Siwek 20-L chambers indicated comparable results in terms of uniformity of dispersion. However, transmission data from the Siwek 20-L chamber were significantly lower than those of the PRL and Fike chambers. Again, this was attributed, in part, to the significant reduction in particle size that occurred during dispersion in the Siwek chamber. The design of the outlet (dispersion) valve of the Siwek 20-L apparatus charge vessel was largely responsible for the particle break-up. The contribution to particle break-up by the dispersion nozzles and the high level of turbulence in the chamber were found to be minimal. This is a significant finding in that the dust particle size tested for explosibility in the Siwek chamber is considerably smaller than the original dust sample.

By Thomas M. Barczak

The effect of load rate on the load-carrying capabilities of wood cribs is investigated in this Bureau of Mines study. The modulus of deformation (stiffness) of wood crib blocks has been shown to increase with increases in rates of load application, causing larger load reactions for increases in convergence rates. Since wood cribs are tested in the laboratory at convergence rates that are orders of magnitude faster than typically would occur underground, wood cribs tested in the laboratory will react larger loads than the same cribs would react underground for the same displacement. Tests conducted in the Bureau's mine roof simulator on green wood crib blocks indicate that the increase in stiffness for increasing load rates diminishes at displacement rates beyond 0.1 in/min, making crib load nearly independent of load rate for rates faster than 0.1 in/min. Seasoned wood specimens were not as con-sistent in load-rate dependency. Some possible explanations of observed load-rate behavior on wood crib specimens are also postulated in this paper.

Jan 1, 1988

By B. S. Covino

The Bureau of Mines, U.S. Department of the Interior, is conducting research to devise substitute corrosion-resistant materials by using ion implantation to form alloyed regions near the surfaces of metals. These alloys were prepared by implanting 25-kev Cr+ and/or Ni+ ions into iron. Their resistance to corrosive attack was evaluated by determining their anodic polarization behavior under potentiodynamic conditions in a solution containing sodium chloride, boric acid, and sodium borate. These electrochemical studies have shown that the general corrosion resistance of ion-implanted alloys was comparable to nominally equivalent bulk alloys. The pitting-corrosion resistance of the ion-implanted alloys was superior to that of iron, although not as good as that of most of the bulk alloys tested.

Jan 1, 1980

By A. M. Stubbs

The Bureau of Mines has devised a procedure to selectively extract and recover chromic oxide (Cr203) from waste high-temperature shift catalysts that contain approximately 6 pct Cr and 62 pct Fe, both in oxide form. The Bureau's procedure consists of roasting the waste catalyst with sodium hydroxide (NaOH) or sodium carbonate (Na2C03) followed by water leaching. The chromium from the leach liquor was recovered utilizing an oxidation-reduction reaction with pH adjustment to form a hydrous chromic oxide (Crp3oXHp) precipitate. The roast-leach procedure produced chromium extractions greater than 89.7 pct, with product recovery in excess of 99 pct from the leach liquor. The costs of the NaOH and Na2C03 roast processes, including sizing and equipment-related recommendations, were determined by the Bureau's Office of Process Evaluation. The economic evaluation indicates that producing a Crp3 product, at the present time, is not competitive with the present-day cost of imported chromites. The estimated average operating cost for both processes was $5.44/1b of recovered Cr203 concentrate. However, this procedure offers a potential alternative to the disposal of this waste through landfiIl.

Jan 1, 1988

By Joseph W. Martin

The Bureau of Mines investigated the backscattering of low-energy gamma rays as a method for rapidly determining the incombustible content of coal mine dust. In this method, 60-kev gamma rays from americium-24l penetrate the dust and are reflected by elements in the dust to a thin crystal scintillation detector. The number of backscattered gamma rays is proportional to the incombustible content. Tests of 40 dry, mine-dust samples containing 50 to 100 percent inert material show an average error of 2 percent. Calibration of the apparatus is necessary for each rock dust to account for variable composition. Results for samples containing more than 6 percent moisture are subject to error, but the values are lower than values obtained by chemical analysis, and thus fall on the safe side. Development of a small portable meter based on the backscatter principle appears feasible. Such a meter would find application within coal mines to check the effectiveness of rock dusting procedures.

Jan 1, 1968

By K. Robert Dorman

This Bureau of Mines report describes laboratory and field experimentation in building mine ventilation stoppings, air-door frames, and fan bulkheads with a civil construction technique. Shotcrete is applied to a free-standing, three-dimensional wire-truss panel, which is easily cut and rapidly erected. In mines where shotcrete equipment is available, this technique should be faster and cheaper than conventional block-and-mortar or monolithic concrete construction.

Jan 1, 1980

By James S. Browning, W. H. Eddy

Laboratory batch and small - scale continuous flotation tests were conducted on a ferruginous barite - fluorspar ore from near Sweetwater , Tenn . , to determine the feasibility of producing commercial - grade fluorspar and barite concentrates . The lignin sulfonate - sodium fluoride - fatty acid method of floating fluorspar produced acid - grade concentrates . Flotation of the barite from the fluorspar tailing using petroleum sulfonate yielded concentrates suitable for use as a weighting agent in oil -well drilling muds . The continuous flotation tests , treating about 150 pounds of ore per hour , yielded fluorspar concentrates that assayed 98.3 percent CaF2 and barite concentrates that assayed 91.2 percent BaSO4 . The recovery of the two minerals was 91.2 and 85.2 percent , respectively .

Jan 1, 1964

By Foster Fraas

Electrostatic separation depends on a number of electrical and mechanical properties such as conductance, contact potential, dielectric constant, and particle shape. In routine testing it is desirable that the application of each of those properties be investigated. The conductance property is best utilized in a separator having an ionic field, whereas the contact potential requires a separator with a pure static field. Dielectric constant and particle shape also influence the response in these two fields. There is no separator on the market that can be adjusted for all these requirements. The separator described in this paper is satisfactory for this purpose and is provided with a dielectric electrode, which permits formation of high-intensity static fields.

Jan 1, 1951

By W. J. Wenger

Analytical, geographical, and geological data on 67 samples of crude oils from Utah are presented, along with some correlations and interpretations. Most of the, geologic formations that produce oil in other areas are also productive in Utah; and as in many other locations, the Permian, Pennsylvanian, and Mississippian formations account for the major amount of the total oil produced in the State. Some anomalies and unusual phenomena are noted. Although most Utah oils are low in sulfur, a sample containing the highest percentage of sulfur ever recorded by the Bureau of Mines is among the oils discussed in this paper. Most of the oil from the major producing formations in Utah is low in sulfur; the same formations produce high-sulfur oils in adjoining Rocky Mountain States. Some Utah oils are both waxy and asphaltic, an unusual combination of characteristics. Correlation index curves for some oils are shown suggesting compositional differences in oils from different producing formations. Production statistics trace the rapid rise of oil production in the State after the first commercial discovery in 1947 and indicate a decline in amounts produced since 1959, the year of peak production in Utah.

Jan 1, 1971

By John Durkin

Field studies have been conducted in a large number of coal mines throughout the U.S. to determine the effectiveness of electromagnetic techniques in locating men trapped underground following a mine disaster. Data from these tests have been used to generate models of expected signal and noise distributions as found above mines throughout the coal fields. These distributions have aided in placing the expected performance of a through-the-earth electromagnetic communications technique into a probabilistic framework. Results indicate an expected 45% probability of detecting a miner's signal from a depth of 1,000 ft, a depth which exceeds 903 of the coal mines within the U.S. and a 90% probability at a depth of 500 ft, a depth which exceeds 50% of the mines.

By Kenneth J. Miner

Pittsburgh bed and Lower Freeport bed coals were tested in the U.S. Bureau of Mines two-stage froth flotation pilot plant, which utilizes a new flotation process to remove pyritic sulfur. The process consists of a first-stage coal flotation step to remove coarse, free pyrite and other refuse in the tailings. The clean coal froth concentrate is then repulped and treated with a coal depressant, a pyrite collector, and a frother to selectively float the remaining pyrite in a second stage. Results in the pilot plant were excellent, comparing well with those obtained in laboratory batch tests. That is, about 70 percent of the pyrite present in the Pittsburgh bed coal and about 90 percent of the pyrite present in the Lower Freeport bed coal were removed with excellent final clean coal recoveries.

Jan 1, 1973

By D. R. Flinn

The Bureau of Mines has studied the electrochemical parameters important to the preparation of coatings of the platinum-group metals. Using molten mixtures of sodium and potassium cyanides in an inert atmosphere, techniques have been developed that permit the preparation of baths for platinum, rhodium, and iridium electrodeposition. Cyclic voltammetric and slow sweep rate linear polarization techniques have been utilized to determine optimum potential and current values for preparation of plating baths and for the electrodeposition of coatings. Techniques are described for the deposition of platinum and rhodium coatings at near 100 percent anode and cathode current efficiencies, and for iridium at approximately 80-percent efficiency. Palladium deposition from these molten cyanide baths remains un-satisfactory. The chemistry of the palladium-containing cyanide bath is discussed. Examples of scanning electron microscope photomicrographs of typical platinum coatings are presented. Techniques are described for the preparation of platinum coatings on large objects.

Jan 1, 1982

By Brian G. White

Two examples of en echelon mining-induced fractures seen in hard-rock mines provided a basis for inferring that fracture zones and bedding plane separations immediately surrounding mine openings are promoted by oblique shear into the openings. It is hypothesized that initial fractures or separations form at the corners of openings as a result of high stress and physical constraint on the rock's ability to deform elastically toward the opening. These conditions result in a locally preferred direction of shearing. The shearing, in turn, generates tensile stress that initiates a progression of systematically offset fractures approximately parallel to the direction of greatest compressive stress. The fractures or bedding separations create tabular rock layers that amplify shearing displacement through bending and dilation. Such shearing effectively reduces and redistributes the compressive stress, but significant dilation is an inevitable consequence. The combination of dilation and shearing and the progressive development of fracture zones have important implications with respect to ground support. The concept of mining-induced fractures forming as a result of shear is illustrated by two examples from coal mines. First, fractures seen at longwall faces probably result from shear associated with subsidence. The fracture zone that develops approximates or possibly defines the draw angle of subsidence. As the face advances, fractures extend downward along the lower edge of the fracture zone, while upper extensions of the fractures are pressed closed. Fracture zones in entry roofs provide a second practical example. Here, mining-induced fractures typically follow bedding planes. The shear zone model suggests that the first bedding separations develop near the edges of the roof and successive separations progress upward and toward the center. However, if the direction of greatest stress is inclined with respect to the roof, a fracture or bedding separation zone may propagate from one side only and also extend higher. Because coal ahead of the face provides some support against lateral shear deformation, bedding separation is inhibited near the face. Rock bolts installed close to the face ultimately become more strained and bent than bolts installed a few meters from the face, and bolts installed through the more remote part of a separation zone may ultimately experience the greatest tensile and bending strains. This model is supported by field data documenting progressive bolt failures that rapidly propagated downward across the roof during face advance.

Spectrochemical methods were developed to determine beryllium in the concentration range 0.0015 to 4.0 percent in siliceous mineral beneficiation products. Two methods are described. They are (1) a fusion-pellet-spark procedure (spark method) and (2) a sustaining alternating-current arc procedure (arc method). In the spark method the sample is fused with lithium tetra-borate and vanadium pentoxide. The resulting bead is crushed, mixed with powdered graphite, and briquetted. This is analyzed spectrographically using controlled high-voltage spark excitation. In the arc method the sample is diluted with germanium metal, graphite, and vanadium pentoxide. Weighed charges are packed into cupped graphite electrodes and subjected to excitation with a sustaining alternating-current arc. Vanadium serves as internal standard for both methods. Effects due to matrix variations in samples and standards are eliminated either by fusion with lithium tetraborate in the spark method or by dilution with germanium and graphite in the arc method. Beryllium determinations show deviations from accepted chemical values of approximately 5 and 8 percent for the spark and arc methods, respectively. Analyses can be made more rapidly by the arc procedure with a sacrifice in precision and accuracy. Either method can be applied to the determination of beryllium in silicate rocks.

Jan 1, 1962

Reduce face methane concentrations and help prevent miners from working under unsupported roof while moving the curtain. Approach Use water sprays on the continuous mining machine to move and direct air to the face, and also provide appropriate installation guidelines for the most effective use of the system. I n laboratory tests and under actual mining conditions, the spray fan has proved an effective means of ventilation. Recent observations in the field, however, have shown that not enough technical information is widely available on proper installation of the spray fan. This Technology News is designed to rectify that situation by providing a concise guide for spray fan installation. How the System Works Good ventilation is essential for methane control. The spray fan system repositions regular water sprays to help the normal exhaust face ventilation do a more effective job. The various water sprays help in many ways: 1. Side sprays bring clean air along the side of the miner into the off-curtain corner.

Jan 1, 1983

By D. Bienstock

A rig was constructed to burn 100 to 125 lb of coal per hour at 4,000° F in a cyclone burner with oxygen-enriched air preheated to 1,500° F to ascertain the problems in the coal-fired MHD generation of power. Potassium carbonate was added to the coal at several concentrations up to 1.23 g-moles/kg of coal (17 lb K2C03/100 lb coal). Boiler-tube materials maintained at wall temperatures of 800° to 1,500° F were exposed to the combustion effluent of 1,800° to 2,500° F. Practically complete removal of sulfur dioxide from the stack gas was achieved with the seed addition. Nitric oxide formation followed theoretical expectations at combustion temperatures with some decomposition of the NO occurring as the gas cooled flowing through the system. Nitrates in the fly ash were less than 1.7 percent of the total fixed nitrogen. With aqueous extraction of the fly ash a maximum recovery of 75 percent of the potassium was obtained. Haynes 25 was unattacked at a wall temperature of 1,500° F in combustion gas at 2,500° F; the stainless steels 310, 316, and 446 were resist-ant at a metal temperature of 1,100° F in gas at 2,100° F.

Jan 1, 1970

By A. F. Colombo, R. T. Sorensen, D. W. Frommer

The Bureau of Mines developed a flotation method for concentrating spiral tailing produced from pilot plant tests on the Champion mine ore fines . The feed material contained about 49 percent Fe and 15 percent SiO2 and was posed mostly of specular hematite , muscovite , and chlorite . Bench- scale , batch flotation research developed a reagent suite composed of tall oil - fatty acid , fuel oil , sulfuric acid , sodium fluoride , and sodium silicate for recovery of iron minerals in the froth product . Concentrate made with the reagent suite contained 87.3 percent of the iron and analyzed 65.6 percent Fe and 1.9 percent SiO2 . Continuous flotation tests were made with a nominal feed rate of 400 lb /hr , but without middling recirculation . Using nearly the same amount and complement of reagents as in the batch tests , three similar continuous tests gave concentrates averaging 63.9 percent Fe and 3.1 percent Sio while recovering about 86 percent of the iron .

Jan 1, 1964

By D. J. Parker

Owing to its flexibility, convenience, economy, ands availability, electric power is peculiarly adapted to the needs of the coal -mining industry. Because of such obvious advantages, the application of electricity has in recent years become more and more extensive and is now a most important factor in the Nation's coal prediction. With the introduction of this type of power into coal mines certain new, specific, and well-recognized hazards resulted. The question arises, therefore: Has the industry met these hazards squarely and. effectively? With respect to some individual companies, the answer happily is in the affirmative; with respect to the industry as a whole, there is much room for improvement.

Jan 1, 1933

By Charles A. Kumbe

"INTRODUCTION The Sullivan Mine was examined by Thomas L. Chapman, an engineer of the Bureau of Mines, in March 1943. Samples taken from the few mineralized exposures justified further investigation of the property. To determine whether extensive exploration of the property would be warranted, the Bureau did a small amount of trenching and underground work during April 1943, 3/ under Bureau project 1462.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its, primary objective the, more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratary project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurigical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests.The investigations of the and Metallurgical Branches of the Bureau, as reported in this paper, were supervised by J. Hedges, district engineer for Arizona, and S. R. Zimmerly, regional engineer for the Western Region, respectively."

Feb 1, 1947

By R. S. DeCesare

Operation of the Bureau of Mines raw refuse continuous separation pilot plant is described, including modifications made to plant equipment for improved performance. Products recovered from refuse, many of which have been evaluated by other laboratories and private firms, are discussed. Sampling procedures used in the pilot plant and detailed data obtained from processing refuse from 13 municipalities are presented in appendixes. Fuel evaluations made on combustible fractions of refuse from the various municipalities are also presented. Information and data obtained at the pilot plant have been used to assist many municipalities in solving their urban refuse problems.

Jan 1, 1980