Search Documents

By W. P. Haynes, J. W. Mulvihill, G. B. Taylor, S. Katell

Capital and operating costs have been estimated for separating methane and hydrogen in gas - separating plants designed to produce 90 million scf per day of product gas containing a minimum of 90 percent methane . After a preliminary literature review of various separation techniques , three different processes --moving - bed adsorption using active carbon , oil absorption , and liquefaction -- were chosen for the cost estimates . Three different methane feed gas concentrations , 5 , 20 , and 50 percent ( cases 1 , 2 , and 3 , respectively ) , were chosen as representative methane concentrations for the separation estimates . Capital and operating costs were lowest for the moving - bed adsorption process in all three cases investigated . Operating costs declined from $ 0.24 to $ 0.06 per 1,000 cu ft of product gas , and capital costs declined from $47,490,800 to $7,411,200 as the percentage of methane in the feed gas increased from 5 to 50 percent .

Jan 1, 1964

Case 1: A driller-helper was pulling a winch cable toward a stack of drill steel when the cable contacted a 12,000-volt power line. The helper was killed, and the driller at the rig controls was severely injured. [ ] Case 2: A crew was preparing to remove a pump from a well when the hoist boom contacted a 4160-volt power line. The hoist operator was electrocuted. [ ]

Jan 1, 2005

By T. Ruff

Researchers at the National Institute for Occupational Safety and Health, Spokane Research Laboratory, studied technology and methods that could reduce accidents involving surface mining equipment that collides with other vehicles or workers, or drives over an unseen road edge. These accidents are partially attributed to the lack of full visibility around these large pieces of equipment. Blind areas can be extensive and this report presents plots of blind areas for five pieces of surface mining equipment. Several technologies designed for detecting obstacles in blind areas and providing a warning to the operator were evaluated on off-highway dump trucks. These proximity warning systems included radar, sonar, GPS, radio transceiver tags, and combinations of radar and cameras. A summary of test results is presented in this report, along with guidance on effective proximity warning technology, installation and maintenance considerations, and recommendations for effective implementation. This study found several commercially available systems that could effectively warn an equipment operator of an impending collision. Several new technologies also show promise for reducing these accidents. In most applications, it is recommended that sensor-based systems be combined with video cameras to provide important alarming functions along with an actual view of the blind area.

Jan 6, 2007

By Francis X. Cannaday

The purpose of this investigation was to find whether the moduli of elasticity obtained were the same for the following methods : ( 1 ) Deformation of a borehole in a prism subjected to uniaxial stress ; ( 2 ) deflection of a thin beam of uniform cross section uniformly loaded ; ( 3 ) sonic - pulse velocity measurements , and ( 4 ) strain measurements on a prism under uniaxial stress . The rock tested was chosen for its good elastic behavior and relatively good homogeneity and elastic isotropism . The same rock was used for all methods . Results indicate that for given environmental and stress conditions the moduli obtained by each of the four methods check one another within the limits of experimental error and that the differences introduced which are characteristic for each method are smaller than physical variations within the rock tested .

Jan 1, 1964

By J. G. Walters

In 1928, the Coal Carbonization Section of the Federal Bureau of Mines, in cooperation with the American Gas Association, began a survey of the carbonizing properties of American coals. A standard test method for evaluating the carbonizing properties of coals that met the following conditions was developed: To yield products similar to those obtained in commercial operations. To produce yields sufficient to permit analyses and tests of quality. To be laboratory size. To be convenient to operate. To permit reproducible control of test conditions and results. This test method has become known as the Bureau of Mines-American Gas Association (BM-AGA) test (53),3/ and more coals of greater variety have been tested in this apparatus than in any other of similar scale.

Jan 1, 1961

By Jerry B. F. Champlin

NIOSHAn accelerated testing procedure developed by the Bureau of Mines for evaluating commercially available corrosion inhibitors is described. Ultra-sonic agitation of the corrodent solutions and the hot-finished mild steel test coupons was used to evaluate the effects of several variables on the effectiveness of two corrosion inhibitors. Small changes in the weight of the test coupons in both controlled and inhibited corrodents, before and after exposure, affected the precision and accuracy of the results. Minute amounts of oxygen in the systems were found to be causing the relatively large deviations in the corrosion developed in the controlled tests. Microscopic examination of the test coupons revealed that both surface preparation and internal strains resulting from fabrication methods materially affect corrosion behavior.

Jan 1, 1965

By B. C. Parks

This paper is a report on the relationships between petrographic composition, chemical composition, physical properties, and thermal behavior of banded bituminous coal. It describes the relationships between petrographic composition, behavior in various laboratory tests, and carbonizing properties of different petrographic types of coal that occur in relatively thick benches in a single bed of high-volatile A bituminous coal - the Hernshaw bed of Boone County, W. Va. Thin-section microscopic analysis and free-swelling index determinations of the thin-section samples were made of a standard column sample. A standard face sample, a representative channel sample, and representative samples of two prominent petrographic benches of bright and dull coal were subjected to chemical analyses and free-swelling-index, plasticity, dilation, agglutinating, low-temperature carbonization, and BM-AGA retort tests. A float-and-sink separation was also made of part of the standard face sample. The fractions from this gravity separation were subjected to petrographic and chemical analysis and free-swelling-index, plasticity, and dilatation tests.

Jan 1, 1959

By Howard C. Pettibone

Mine safety personnel reported occurrences of excessive "glove-fingering" and other problems with resin-grouted roof bolt installa tions. To study these problems, the Bureau of Mines designed a test plan to (1) obtain baseline information on several resin cartridges and (2) investigate the variables involved in the installation of a resin bolt. Three brands of resin representative of the industry in January 1983 were selected for cartridge evaluation. The installation variables selected for study were the method of installation, the hole depth, and the hole annulus. These variables were studied by installing a series of bolts in concrete blocks using different values for each variable. Results of the research show overspinning the resin may cause problems, but they can be avoided by using the spin times recommended by manufac-turers. Excessive glove-fingering is not a problem if the manufacturer-recommended installation procedures are followed.

Jan 1, 1987

By Philip C. Good

Preliminary studies showed that direct hydrolysis of H2SiF6 to SiO2 and HF at elevated temperatures was subject to many mechanical difficulties, and that corrosion of construction materials was a serious problem. Elimination of SiO2 from the HF product was generally poor. An alternative procedure, hydrolysis of lime-neutralized H2SiF6 by steam at 950° to 1,100° C, yielded a product very low in SiO2. Condensates containing up to 300 g/1 HF were prepared.

Jan 1, 1968

By John W. Thatcher

A demountable X-ray tube vacuum spectrograph was designed by the Bureau of Mines for the determination of long-wavelength X-ray spectra from the light elements. This instrument was operated for both secondary and combined primary-secondary excitation of the aluminum K-series. There was an increased analytical sensitivity for elements in period 3, and an indication that with improved X-ray tubes or direct election excitation of the sample, X-ray determination of elements in period 2 is also possible.

Jan 1, 1965

By R. A. Guidotti

The Federal Bureau of Mines studied the thermal decomposition of the nitrides of the Group V A metals (CbN, Ta3N5, and VN) with the goal of preparing high-purity metals. Solid-state purification and arc and electron-beam melting were examined. Electron-beam melting proved to be the most efficient means of nitrogen and oxygen removal. Columbium and tantalum of 99.9-pct purity were prepared by this technique; in the case of vanadium, however, nitrogen could not be reduced below the solid-solution level.

Jan 1, 1976

By Phil Patton, Bill M. Stewart, Curtis Clark

Handling materials in underground mines continues to be a major safety problem. To help reduce materials-handling injuries, the National Institute for Occupational Safety and Health (NIOSH) at the Spokane Research Laboratory is developing, modifying, and testing equipment to replace the necessity of doing lifting tasks manually. To reduce single-event lift injuries, equipment having mechanical automatic weight sensing and balancing control was investigated. The Coleman manipulator was selected for testing. Modifications to the Coleman manipulator to make it more suitable for underground mine use included mobilization, self-containment, all-purpose gripper attachment, and support jacks. To reduce or eliminate the need to clean off manually the materials that commonly plug grizzly openings (timbers, wire mesh, roof bolts, and other debris), a track-guided pincher arm device was developed. The TGPA attaches to an impact hammer head, and the pincher arms are controlled by the operator of the hammer. Oversized rock can be broken with the pincher arms in the up position; the arms can then be lowered to grab and remove debris. Sweeping action to remove cohesive fines bridging grizzly openings is also greatly improved. This device is especially useful in recessed grizzlies. An industrial gun was tested to evaluate its effectiveness in breaking oversized rock. Boulders up to 76 cm in diameter were successfully broken to minus-33 cm. Although methods to control fly rock need to be developed, an industrial gun may be a safe and inexpensive alternative to breaking oversized rock in certain underground mining situations.

By J. N. Geyer

In coal mining it is essential to maintain the roof over working places and roadways in the safest condition possible. To this end every effort should be made to win the coal with the least injury to the immediate roof strata, as broken strata certainly present a greater hazard than a sound roof. The chief causes of injury to the roof in mining are inherent in the method of development and recovery and the blasting practices followed. The first, which may produce severe stresses in the roof, weakening it over comparatively large areas has been discussed in previous papers3 and will not be treated here. The second cause is local in effect, but with the same general method of blasting being employed throughout a mine having uniform roof conditions, similar effects on the roof may be expected. In the Bureau's investigation of accidents caused by falls of roof and coal it has been necessary to make a careful study of blasting practices and their effect on the immediate roof. The purpose of this paper is to show the effect of the observed methods of blasting on different types of roof and to point out methods that have been proved to be least harmful to the roof strata. The data used in preparing this paper have been compiled from reports made by Bureau engineers engaged in the study of falls of roof and coal, and embrace mines opened in the Pittsburgh coal in Ohio and Pennsylvania and the Pittsburgh and Sewickley coals in West Virginia.

Jan 1, 1933

By H. O. McDonald

The Bureau of Mines reviewed the chemical vapor deposition (CVD) literature of the group IVB, VB, and VIR elements. This review was utilized in the Bureau's research to provide erosion-, abrasion-, and corrosion-resistant coatings for valve components used in coal gasification units. This report attempts to bring together the many CVD references that have been published since 1966. Each of the group IVB, VB, and VLB metal coatings were reviewed, and some of their preparation methods, uses, and properties are given. A total of 160 references were found for the nine elements. Isotope separation, stronger steels, solar absorbers, alloys, superconductors, optical fibers, and coatings to increase the life of materials are some of the new uses for CVD.

Jan 1, 1979

By O. C. Blade

"INTRODUCTION This report on the properties of motor fuels sold through service stations in the United States is a continuation of a series of reports made in accordance with a cooperative agreement between the Coordinating Fuel Research (CFR) Committee of the Coordinating Research Council (CRC) 3/ and the Bureau of Mines of the United States Department of the Interior. The first of these reports presented data on motor gasolines sold during the winter of 1935-36.4/ Further reports were issued describing motor gasolines sold during the succeeding sum¬mers and winters to and including the summer of 1941.4/ No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed.!The present report presents analytical data for 4,544 samples, represent¬ing the products of 124 companies. The samples represented in this report were obtained during December 19146, January and February 19-(. As in previous surveys, the companies covered Ly the survey include both large and small suppliers. Conforming to former reports, the data cover three groups of samples - regular-price, premium-price, and third-grade gasolines.As the number of analyses submitted for samples of third-grade gasoline are not considered adequate to represent this type of motor fuel, data for the analyses have not been averaged, but the individual items are tabulated. The number of samples, items, and brands comprising each group is as follows: Regular-price, 2,368 samples, 319 items, and 113 brands; premium-price, 2,172 samples, 289 items, and 106 brands; third-grade, 4 samples, 4 items, and 4 brands. The meanings of these terms as used in the surveys are as follows:"

Aug 1, 1947

By T. L. Iapalucci

To determine the behavior of chlorine in coal combustion, the Bureau of Mines burned 10 chlorine-containing coals, high-, medium-, and low-volatile, in a laboratory-scale pulverized-coal combustor. At carbon-combustion efficiencies of 94 to 98 percent, 1.6 to 7.1 percent of the chlorine or an average of 4 percent of the chlorine in the coal was retained in the ash; the balance, predominantly hydrogen chloride, was evolved in the combustion gas. Sulfur retention in the ash ranged from 2.3 to 10.7 percent or an average of 6.3 percent, Addition of alkali and alkaline earth carbonates to a medium-volatile coal containing 0.27 percent chlorine by preferentially reacting with the chlorine increased the Cl/S atom ratio in the ash, Lithium carbonate addition at 0.43 percent and K2C03 at 1.59 percent increased the C1/S ratio in the ash from 0.2 to 0.6.

Jan 1, 1969

By Frank C. Andreuzzi

The Federal Bureau of Mines conducted a demonstration project to reclaim 125 acres of abandoned strip-mined land in Lackawanna County, Pa., for public recreational, historical, and educational use as a park. The Bureau was involved in the development of the general site plan, and engineered and supervised the basic land rehabilitation. The park's Facilities include outdoor recreational activities, picnic grounds, children's play areas, primitive overnight camping, and winter sports. A major attraction is the Anthracite Museum constructed by the Pennsylvania Historical and Museum Commission The project may serve as a prototype for reclaiming existing and future surface-mined lands.

Jan 1, 1976

By P. V. Fillo

This paper describes Mohave Mining and Milling Co. methods of mining and milling manganese ore in Arizona. It is one of a series of publications prepared by the Bureau of Mines on methods and costs in various mining districts in the United States. Production of manganese ore, as such, in Arizona began in 1915. Before this time manganiferous ores had been mined primarily for silver content and used as a smelter flux. From 1916 to 1918 approximately 69,000 long tons of manganese and mangsniferous ores were mined. After World War I production dropped to almost nothing until World War II, during which period more than 24,000 long tons were produced. A lull in mangonese mining occurred after World War II, having production rates of only a few hundred tons annually through 1952.

Jan 1, 1963

By H. M. Harris

The Bureau of Mines investigated chlorination of domestic ilmenites in a fluidized coke bed at temperatures of 950° to 1,150° C. Objectives were to develop an effective process for producing TiC14 suitable for TiO2 pigment and to reduce pollution by collecting and treating waste byproduct chlorides. The reactor for these tests was a 10.2-cm-diam quartz tube heated externally by electrical resistance heaters. It contained coke beds of from 35.6 to 82.5 cm in depth that were fluidized by 13 to 25 l/min of chlorine. Ilmenite concentrate powders were introduced at the bottom of the fluid-bed reactor, using the chlorine gas stream as a carrier. Test results showed that greater than 90 pct of the ilmenite reacted at optimum conditions and recovery of TiC14 ranged from 95 to 99 pct of stoichiometric. A temperature-controlled cyclone was used to remove high-boiling-point chlorides such as MnCl2, MgCl2, and FeCl2, and also collected fine unreacted ilmenite and coke dust. Impure TiC14 and FeC13 were separated by collecting the, iron chloride in a condenser con-trolled at 200° C. Titanium tetrachloride vapor was cleaned by passage-through a salt-column filter followed by condensation in water-cooled and refrigerated condensers. Liquid TiC14 was purified further by well-known industrial methods to meet specifications for pigment-grade chloride. Integrated tests were conducted in which chlorine, produced by dechlorination of FeC13 with oxygen, was recycled and used directly in a fluidized-bed chlorinator.

Jan 1, 1976

By G. L. Gates

The Bureau of Mines studied the scales formed in producing wells in the Wilmington field, California. The scales were primarily barium sulfate and resulted from the mixing of injected sea water and formation waters; there was excess sulfate in the injection water and the formation waters contained appreciable barium. After breakthrough, the produced brines were supersaturated with barium sulfate. Laboratory tests indicated that barium sulfate precipitated quickly When the supersaturated brines were agitated with crystals of barium sulfate and fairly rapidly when more sulfate solution was added. Precipitation occurred slowly on standing or under nonturbulent conditions. Both the apparent and equilibrium solubilities of barium sulfate in these brines were determined and compared with equilibrium solubilities in distilled water and sodium chloride solutions.

Jan 1, 1965