Search Documents

By Wilbur A. Haley

The demand on the nation's reserves of high-quality coals suitable for metallurgical purposes is resulting in the rapid depletion of some of the thicker coal beds. These beds are thick enough to permit the use of modern mechanized mining equipment. Many of the thin beds are not being mined at present. In limited areas where the coal is less than 36 inches thick some beds are mined by various conveyor methods. Usually, the room-and-pillar system or some modification of it is used, and often no attempt is made to extract pillars. Consequently, an appreciable quantity of a valuable resource is lost. Many steel companies and coal operators consider reserves of low-and medium-volatile coking coals to be critical, especially in areas where the thin beds are not being mined by modern mining methods. To improve recovery and to promote more-extensive mining in thin beds, methods and devices that are new to American coal mining but applicable to the mining of thin coal beds should be tried. As one of the functions of the Bituminous Coal Mining Section of the Bureau of Mines is to promote improved mining practices and efficiency in the interest of conservation, research in that line is necessary. In 1945 coal planers were observed in operation in Germany by a Bureau engineer member of Solid Fuels Mission to Germany. Planer designs and history of early developments and operations were published. In 1949 an improved planer was again studied by Bureau engineers, and its adaptability to certain conditions in the United States, especially thin beds of friable coal, was considered practicable. After the war the planer was improved, in design and for several years has been operating successfully in the Ruhr. Because of the conviction that the device would be successful, both from the standpoint of conservation and operational prodl1ctivity, under certain conditions in the United States, the Bureau of Mines, through the Bituminous Coal Mining Section, entered into a cooperative agreement with the Coal Division of Eastern Gas & Fuel Associates and Mining Progress, Inc. The purpose of the agreement was to conduct an experiment in modified longwall mining, using a new-type German-built coal plow or planer, known as the Loebbe Habel, supplied by Mining Progress, Inc. The experiment was made to determine if this type of mining equipment operated on a longwall face could be adapted to some of the thinner American coal beds. Such an experiment also would afford many opportunities to study the possibilities and principles of this type of equipment as well as the many factors involved in the mechanical mining of a longwall face.

Jan 1, 1952

By D. J. Parker

Before the various States began to enact workman's compensation laws accidents were considered inherent in many industries, and little or no effort was made to prevent or reduce them. The hazard was accepted by the employee with the job, and the avoidance of accidents by mental alertness or physical agility was largely his responsibility. After the employee had given evidence of enough skill inn performing his allotted task efficiently the responsibility of the employer apparently ceased with respect to the personal safety of the employee. However, following the enactment of workmen's compensation laws, at least two facts that had not before been fully appreciated soon became apparent: (1) The majority of accidents can be prevented if the management firmly determines to prevent them; (2) frog a monetary point of view alone accidents are decidedly expensive, both to employer and to employee. It is now evident that savings effected by conscientious safety effort add substantially to net profits of operation.

Jan 1, 1934

By R. G. Knickerbocker, C. T. Baroch, A. W. HACKWOOD

The difficulties inherent in the production of alumina by the formation of potassium alum and its subsequent thermal dehydration and decomposition have been overcome , to a large extent , in a process developed at the Boulder City Station of the Bureau of Mines . This process is applicable to the reserves of alunite known to occur in several Western States and , possibly , to certain clay and low-grade bauxite deposits known to exist in this country . The operations sequence of the process is shown in the flow sheet (fig . 1) . Only those steps included within the heavy line are considered in this report . Four different procedures for dehydration of alum were investigated ; ( 1 ) Spray drying , ( 2 ) rotary - kiln drying , ( 3 ) dry grinding in a thermal ball mill , and ( 4 ) dehydration in the vertical- column flash dehydrator . Based upon fuel requirements and other practical considerations , the vertical- column dehydrator , or some modification of its operating principle , offers the botter possibility for commercial use .

Feb 1, 1946

By Frank D. Lamb, Lloyg H. Baning

"The crushed-stone industry has long been troubled with the problem of producing a more or less cubical product for use as concrete aggregate. Its seriousness varies widely for each producer, depending upon the character of the rock employed for raw material and the ultimate use of the crushed stone. For many construction uses, such as the macadam or bituminous-concrete- type road, flat pieces are not objectionable and may even be preferable to more cubical rock. However, most specifications for concrete require that the stone must be reasonably free from flat and elongated pieces.The rigid specifications set by many contractors have resulted in the rejection of coarse aggregate that, except for the presence of an excessive amount of flat and elongated pieces, would be entirely acceptable. In many instances, if an efficient, economical method of removing flat and elongated pieces were available, local producers could meet the requirements of the contractor and thus eliminate the necessity for importing more cubical material.A brief investigation of the problem of removal of flat and elongated pieces from crushed aggregate, carried out at the Eastern Experiment Station of the Bureau of Mines, indicated that it is mechanically possible to remove flat pieces from crushed rock.TEST EQUIPMENTA number of mechanical devices are used by the coal industry for separating slate from coal; these depend upon the difference in shape of the crushed slate as compared with the coal. Such devices as shutter screens, spiral separators, and the Norman picker would be suitable for removing flat pieces from crushed rock in the same manner as they are used by the coal industry. None of these devices was immediately available for testing purposes, so an attempt was made to construct a simple device that could be used in commercial operations."

Sep 1, 1944

By H. H. Schrenk, L. B. Berger, Robert L. Beatty

"INTRODUCTION Toxic oxides of nitrogen 5/ are formed or liberated in many industrial process and may constitute a definite hazard to the health of persons exposed to the atmospheres thus produced. Oxides of nitrogen occur in the gases involved in the use of explosives, in the gasoline products of welding operations in the exhaust of internal-combustion engines, in the vicinity of electrical discharges, in the combustion of nitrated materials, and in chemical process involving nitration or the use of nitric acid, Itis evident that oxides of nitrogen may constitute an occupational hazard in many industries, and therefore it is important that those concerned with the control of such hazards be equipped with a technique suitable for the determinations of oxides of nitrogen in the concentrations of,hygienic significance."

Feb 1, 1943

By Joan T. May

The Federal Bureau of Mines investigated the potential for recovering aluminum from copper-dump leach liquors by use of single-contact ion-exchange technology. A strongly acidic ion-exchange resin was used to extract aluminum from a typical dump leach liquor and from synthetic leach liquors. Aluminum was stripped from resin with a HS04 or NaCl solution. Bench-scale experiments indicate that a single-contact ion exchange is technically feasible, but that the process is limited by the relatively low loading capacity of the resin and the excessive amount of stripping agent required. A further limitation is that significant amounts of magnesium and iron are loaded and stripped along with the aluminum.

Jan 1, 1976

By W. R. Hardwick

This information circular describes mining methods and practices at New Cornelia Branch, Phelps Dodge Corp., Ajo, Ariz. It is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. The New Cornelia mine (fig. 1) is at Ajo, a town in southwestern Arizona (fig. 2) on Arizona State Highway 85 in the western part of Pima County. The [oncentrator] and smelter are near the mine (fig. 3). Copper ore is mined, crushed, ground, and concentrated, and the concentrates are smelted. Copper is cast in anode form and sent to the Phelps Dodge Corp. refinery in El Paso, Tex.

Jan 1, 1960

By C. W. Dwiggins

This report describes the development, theory, and application of techniques and instruments for quantitatively determining nickel, vanadium, and iron in oils, using direct, X-ray emission spectrographic methods (5, 6).3 The methods developed apply to petroleum and other oils as well as some specific fractions of oils. The quantities of nickel, vanadium, and iron in various petroleums are of practical and theoretical interest. Even traces of nickel and vanadium may poison cracking catalysts, and X-ray methods have been used for determining nickel in such catalysts (7). At least parts of the nickel and vanadium occur as metal-porphyrin complexes, a fact which may have considerable bearing on knowledge of the origin of petroleum.

Jan 1, 1962

By J. B. Littlefield

The term "konimeter" is used generally to designate a type of dust-sampling instrument that collects the dust from a small volume of air by impingement on a glass plate prepared aced with an adhesive film. The konimeter was first developed by Sir R. N. Kotze about 20 years ago and was followed a few years later by the circular-type konimeter, by which a number of samples may be collected on a glass disk. The present discussion will be confined to the circular type, as it is used most. Various techniques have been developed for using the konimeter, and many materials, such as petrolatum, mineral oil, and glycerine jelly, have been used in preparing the adhesive film. In South Africa, Australia, and Canada, where the konimeter has been employed most widely, dust samples are treated by ignition and washing before being counted. In Canada the dust samples are collected on a disk of special heat-resistant glass prepared with a film of mineral oil; the disk is then heated to a dull cherry-red in a muffle-furnace to remove the film and organic matter, cooled, and washed with a few drops of 50-percent hydrochloric acid followed by distilled water and alcohol, and then heated again to remove residue left by evaporation of the alcohol. After this treatment, the dust samples are counted under a magnification of 150 diameters with dark field illumination.

Jan 1, 1938

By Boyd Guthrie

Methods of distilling topped crude oils and distillates under vacuum, accompanied by good fractionation, have taken a place of major importance in the refining industry. In the refining of petroleum products it is generally desirable to produce a distillate of good quality, and this objective is attained by fractionation of a high degree. The laboratory and commercial practice have proved that by varying the amount of fractionation the quality of the distillate can be changed, and refiners are cognizant of the advantages of good fractionation. Distillation under high vacuum, however, is a relatively new practice in petroleum refining, and only during the last few years has there been an indication that this method may become a general practice in the industry. Vacuum distillation offers many advantages over older methods of distilling petroleum products. Vacuum combined with steam distillation, for example, is replacing straight-steam distillation because the quality of the products of vacuum and steam distillation surpasses that of those produced by straight-steam distillation. Although the injection of varying amounts of steam in a vacuum unit is common practice, the amount of steam used is becoming loss as the vacuum within the unit is increased. This report describes the construction of a visible-action laboratory batch still and fractionating column and gives certain data pertaining to the operation of the apparatus under vacuum for the production of lubricating distillates. The apparatus was designed and built to produce lubricating distillates under as nearly ideal conditions as possible, in order that a subsequent study of the characteristics of the distillates could be made. For example, a study could be made of the distillates obtained up to the point of cracking of the charge if a topped crude were charged to the still; if the still was used as a rerun unit for lubricating distillates a study of nearly the entire charge could be made. Only topped crude has been charged to the still so far, and therefore this paper is limited to the results obtained from the distillation of such a charge. The results so far obtained indicate that such an apparatus is valuable in a study of different crude petroleums as sources of lubricating distillates.

Jan 1, 1932

By S. L. McGill

The U.S. Bureau of Mines has determined the microwave heating rates for a suite of minerals and reagent-grade compounds. Maximum temperature achieved for the samples and the time required to reach temperature are reported. Heating rates of powdered samples are presented as a function of incident powers up to 3,000 W at 2,450 MHz. Descriptions of the microwave cavities, test cells, and a thermocouple assembly used to measure temperature in the microwave field are given. Many minerals of value heated in the microwave field, whereas host rock or gangue materials did not. In general, heating rates increased as incident power was increased. Exceptions to this were some very good (CuO, Fe304, and PbS) and very poor (CaC03 and SiO2) microwave-absorbing materials that showed negligible changes with increased power. Applications demonstrating the use of microwave energy in mineral processing that are described herewith include oxidation-reduction reactions, mineral liberation, and mercury retorting-vaporization. Microwave data on mineral heating rates will provide insight to possible chemical and mineral processing applications as well as assist in predictions of processing parameters.

Jan 1, 2010

Increase the productivity of domestic mining operations by improving the performance of rock drilling systems. Approach Investigate the use of chemical solutions at zero surface charge concentrations as drilling fluid additives to enhance penetration rates and extend bit life. Background Bureau researchers have investigated the use of chemical additives to enhance drilling performance and have found that the most efficient drilling occurred when the drilling fluid was able to maintain a zero surface charge (ZSC) on the rock surface. Laboratory drilling studies using 5/8-inch diameter diamond-impregnated coring bits on rock types such as quartzite, granite, taconite, and marble. Cationic compounds were used as the surface charge neutralizing additives during these tests. The drilling studies demonstrated enhanced drilling performance, however, only at the singular additive concentration that produced the ZSC condition. Bureau researchers made a breakthrough when they found that polyethylene oxide, although a nonionic polymer, was able to maintain the ZSC condition over a wide range of concentrations. Success using polyethylene oxide as the drilling fluid additive during subsequent laboratory tests prompted testing under field conditions.

Jan 1, 1991

By M. L. Whisman

Three samples of waste lubricating oil were re-refined by processes developed by the Bureau of Mines and reformulated with additives to meet designated requirements for viscosity and service. Quality-defining bench-scale tests were used to compare and evaluate the quality of these three motor oils, eight commercially re-refined lubricating oils, and three new lubricating oils. Most of the re-refined oils studied could not be distinguished from new oils by the bench tests used to define quality. There was some evidence, however, that one and perhaps more of the re-refined products investigated might not meet all of the quality standards of new lubricating oil, suggesting the need for better quality controls by re-refiners.

Jan 1, 1974

By Richard D. Miller

This Bureau of Mines publication contains analyses and related source data for 224 natural as samples from 18 States. Of the total, 191 sam¬ples were collected during calendar year 1981. The remaining 33 samples were collected during previous years, but releases, granting permission to publish were not received until 1981. All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by the mass spectrometer and special helium apparatus described previously (1-2).3 The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the general public. Twenty-five publications have presented the results of 12,827 gas analyses made prior to 1981. The first three bulletins (1-3) contain analyses and related data on 5,218 gas samples collected from 1917 through 1960; these bulletins have been supplemented annually by information circulars (4-17, 19-24) containing 7,609 analyses of samples collected since 1960.

Jan 1, 1982

By F. D. Everett

The Federal Bureau of Mines reviewed the status of tungsten deposits of Utah in 1959. Industrial requirements of tungsten during emergencies have exceeded the domestic supply, and a knowledge of the sources of this strategic element may be helpful in the future. Tungsten occurs as the mineral scheelite in deposits that have been developed or explored on approximately 60 properties in 10 of the Great Basin ranges of Utah, none of which were being worked in 1957-59. Ores from most of the productive areas are similar in that they are contained in tactite deposits on or near the contact of calcareous and acidic intrusive rocks. The tactite ores consist predominantly of the silicate minerals garnet, epidote, and diopside and the carbonate rocks limestone or dolomite. Scheelite, where present, is disseminated irregularly in the tactite. Tungsten ores from Utah mainly have been produced from small deposits worked in World Wars I and II and the Korean campaign. The ores were either hand sorted to a grade ranging from 0.5 to 1.0 percent tungsten trioxide (W03) or were beneficiated in small mills to higher grade concentrates. The largest reserve appears to be in the area of the Notch Peak intrusive in the House Range, Millard County. A large part of the reserve in the House Range is mineralized tactite containing 0.2 to 0.3 percent W03. Research on flotation by the Bureau of Mines has indicated a method of concentrating scheelite in tactite ores that average 0.25 percent W03, with at least 85 percent recovery. The concentrate assays more than 5 percent W03 and can be processed into artificial scheelite ready for industrial use.

Jan 1, 1961

By W. R. Hardwick

This paper describes block -caving methods and practices of the Bagdad Copper Corp. in Yavapai County , Ariz . It is one of a series being prepared by the Federal Bureau of Mines on mining methods , practices , and costs in various mining districts of the United States . The story of the Bagdad caving operation is of particular interest because the ore body was not as thick as at other mines where the method had been successful . At Bagdad the caving method worked very well as a smallscale operation of 300 tons per day but was abandoned when production was increased to 2,000 tons per day . The Bagdad mine is in western Yavapai County , Ariz . , about 22 miles northwest of Hillside , a station on the Phoenix -Ash Fork branch of the Atchison , Topeka & Santa Fe Railway system ( fig . 1 ) . Copper ore now is mined by open -pit methods . The ore is concentrated , and the concentrates are trucked to Hillside and shipped by rail to a custom smelter . Some molybdenum sulfide is produced as a byproduct . This report gives a brief history of the district , describes the ore de- posit , and outlines the methods of prospecting , exploration , and estimation of ore . Development and former underground mining , including stope preparation , stoping , and transportation , are described . Extraction of ore , production rates , miscellaneous operations related to mining , wage and contract systems , and method of concentration are described . The final section discusses mining costs . The underground mine was visited by the author several times between 1937 and 1942 , and some information has been drawn from personal notes . The property again was visited in June 1957 , and maps and plans for this paper were furnished by the company at that time ; they have been edited to conform with Bureau of Mines format . The underground mine could not be visited then because it had been closed in 1948 when open -pit mining was begun .

Jan 1, 1959

By L. C. IlsLey, R. A. Kearns

As the use of electricity becomes more and more general in mining opera- tions, interest in regulations governing its application becomes greater. During the past year the electrical section of the Bureau of Mines has made a study of State regulations now in force relating to the use of electricity in coal mines. Technical Paper 271, entitled "State Mining Laws on the Use of Electricity in and about Coal Mines", has been published as a result of this study. The present paper represents a compilation of all laws relating to accident prevention with respect to electrical circuits. This group of regulations is perhaps the most important of any that relate to safety in coal mines. Its importance is shown by reference to accident statistics in Bulletin 115, (Fay, A.H., Coal-Mine Fatalities in United States, 1870-1914, Bureau of Mines, 1916), which show that about 77 per cent of the fatalities due to electricity in and about coal mines were caused by direct or indirect contact with trolley or other power circuits. In actual number this means that of 710 men killed by electricity, 546 were killed by contact with electric wires. Undoubtedly, a large percentage of these accidents might have been prevented had the wires been properly guarded. The compilation follows:

Mar 1, 1921

In connection with tin strategic minerals investigations of the Bureau of Mines and the Geological Survey under authority of the Strategic Materials Act (Public 117, 76th Cong., 1st sess.) a study is being made of tin deposits in the United States in an effort to improve the situation with respect to domestic supplies. These studies include sampling and exploration of some of the larger deposits with the objective of establishing emergency reserves, if possible to do so. Two exploration projects have been completed, and the over-all results obtained are set forth in this progress report. RESOURCES Tin was first discovered on this continent in 100 in the Temescal Mountains of what is now southern California. In the ensuing century, occurrences of tin have been reported in no less than 17 States and Alaska. Although most of these are of scientific interest only, tin-bearing veins and placers in California, Alabama, North and South Carolina, Virginia, South Dakota, Wyoming, Texas, New Mexico, and Alaska have been extensively explored, and largo sums of money have been expended in recurring attempts to exploit them.

Jan 1, 1941

By K. P. V. Lei

The Bureau of Mines investigated molten salt electrorefining 'n helium atmosphere cells as a means for the production of ductile vanadium. 'Electrolytes composed of NaCl-VCl2, LiCl-NaCl-VCl2, BaCl2-KCl-NaCl-VCl2 KCl-LiCl-VCl2, and CaCl2-NaCl-VCl2 were tested. Two electrolytes, KCl-LiCl-VCl2 and CaCl2-NaCl-VC12, were selected for laboratory-scale production tests. A molten salt electrorefining process was developed for the production of ductile 99.6 percent vanadium from a commercial 90-percent grade. Using the CaCl2-NaCl-VC12 electrolyte, an 87-percent recovery of ductile vanadium was made; an 85-percent recovery was made with the KCl-LiCl-VCl2 electrolyte.

Jan 1, 1967

By H. D. Pallister

A review of? reports and literature on the pyrite deposits at Pyriton, Ala., indicated that a large tonnage of pyrite, some of which contained a small amount of copper, had been mined and shipped to fertilizer plants throughout the South. The information contained in this literature tended to demonstrate that the ore occurred in separate lenses of greater or less extent and of varying thickness and richness in pyrite as well as in copper. The outcrop being parallel with the Atlantic Coastline Railroad and just south of it makes the deposits readily accessible for shipment. Slopes could be sunk as they were in the past in the ore body if it were of sufficient grade and thickness, and the ore could be hoisted up the slope and milled close to the slope mouth with an ample supply of water from Talladega Creek, which follows the outcrop closely.

Jan 1, 1949