Search Documents

By Robert H. Peters

Groundfall accidents have been the leading cause of fatalities in the underground coal mining industry for many years. Statistics from the Mine Safety and Health Administration (MSHA) indicate that approximately half of the victims of these fatal accidents were in an area where no devices had been installed to support the mine's roof. This report was prepared by the U.S. Bureau of Mines to summarize the opinions of 268 coal miners, 29 rust-line supervisors, and 30 MSHA inspectors concerning why people go under unsupported roof, and how to prevent this behavior. Interviews were conducted at six minesites.

Jan 1, 1991

By R. C. Adams

This report describes the feasibility of mining the oil shale deposits of the Piceance Creek basin in Colorado by an integrated open pit system. The study is based upon a comprehensive analysis of pertinent environmental, economic, and engineering factors. Ten mining cases are investigated, and the mine design and cost estimates for each case are presented in this report. Nine of the cases represent three cutoff grades, defining oil shale ore as equal to and above 15 gallons per ton (gpt), 20 gpt, and 25 gpt at three ore production levels of 500,000 tons per day (TPD), 1,250,000 TPD, and 2,500,000 TPD. The tenth case is an alternate design of the 500,000 TPD production rate at the above 15 gpt cutoff grade. The report consists of Volume I, a technical and cost comparison of the ten cases; Volume II-Part I, a detailed explanation of the estimating methods used; and Volume II-Part 2, a more detailed discussion of the technical and cost features of the ten cases than is presented in Volume I.

Jan 1, 1976

By George S. Rice

In 1911 the Director of the United States Bureau of Mines instructed the chief mining engineer of the bureau , during an investigation of coal-mine safety conditions in Europe, to ask the directors of the various mine-experiment stations whether they would favor a European conference . The majority of the officials in immediate charge of experiment stations favored the plan , and Victor Watteyne, inspector general of Belgium, suggested that the United States call such a conference to be held immediately after the Eighth International Congress of Applied Chemistry, which was to assemble in New York on September 3, 1912 . Accordingly, invitations were issued by the United States Government to those countries having mine-experiment stations , namely, Austria-Hungary, Belgium, France, Germany , and Great Britain, and to those that contemplated the establishment of such stations , Canada and Mexico . All but Great Britain and Canada accepted ; Mexico designated a representative , who later found it impossible to come. The Government of Great Britain in declining, expressed regret at its inability to accept ; an informal statement was made that the opening of the experimental gallery at Eskmeals , England , occupied the attention of the officials in charge . Delegates were appointed by their respective Governments as follows: Austria-Hungary, Julian Czaplinski , royal mining engineer. Belgium, Victor Watteyne , inspector general of mines . France, J. Taffanel, director of the Lievin experiment station . Germany, Carl Beyling, bergassessor, director of Dortmund experiment station. United States , Charles E. Munroe, consulting explosives expert and George S. Rice, chief mining engineer of the Bureau of Mines . Subsequently Mr. William O'Connor , a mining engineer and mine operator of Wales , who opportunely appeared at the Pittsburgh station with letters of introduction from the South Wales Institute of Engineers and from prominent mining officials of Great Britain , was unanimously invited to take part in the meeting as an unofficial representative of Great Britain . Messrs . Beyling, Taffanel , and Watteyne were met in New York on September 3, by George S. Rice, who accompanied them to Washington, where they were welcomed by Director J. A. Holmes , of the Bureau of Mines , and where , with the delegates to the Eighth International Congress of Applied Chemistry , they were presented to President Taft . Mr. Taffanel was unfortunately called back to France just before the scheduled time of the conference on account of a mine disaster ; the other delegates , including Mr. Czaplinski , convened at Pittsburgh on the morning of September 14. Mr. Rice, representing the Director of the Bureau of Mines , acted as temporary chairman , and called the meeting to order.

Jan 1, 1914

By C. E. Gregory

In terms of a Research Proposals supported by a Grant Agreement dated 30 June 1973, the author was commissioned to prepare an annotated bibliography of mine fires. The main objective was to conduct a comprehensive program of library research and search of official files to prepare a list of articles dealing with actual occurrences of mine fires. This bibliography as now completed includes an annotated reference from each article or report cited, underlining the cause, extent, methods used, procedural errors made, results achieved, ventilation effects, and lessons learned from the operation of subduing the particular fire.

Jan 1, 1974

By Parry. V. F.

"INTRODUCTION Coal is a compressed mass of heterogeneous, macerated, metamorphosed plant remains that have collected in the earth's crust. Probably no two beds of coal have identical properties, and different parts of the same bed may vary considerably when measured by some of the many empirical tests that have been developed to classify or differentiate the properties of coal. Because of this great variability in properties, the commercial processing of coal to produce coke and byproducts has developed largely as an art based on experience, rather than as a science. Much empirical chemical research, however, has been and is being conducted on coal carbonization, and this work is of practical value in obtaining larger yields of gas and byproducts and in the improvement of the physical properties of the coke.Both ultimate and proximate analyses have been used for correlating purposes. 3/ In the United States the proximate analysis is used for the classification of coal according to rank and grade. The proximate analysis can be employed usefully in the coal—carbonization industry because separation of the combustible matter of coal into volatile matter and fixed carbon is, in fact, a small carbonization test conducted on 1 gram of coal heated in a platinum crucible.Small—Scale Laboratory Coking Tests,Many empirical tests have been devised for determining the coking properties and measuring the yield and quality of gas and byproducts obtainable from various coals. These tests, made on samples ranging from 25 grams (about 1 ounce) to 5 kilograms (11 pounds), furnish information that is roughly proportional in practical value to the size of the sample carbonized. However, the cost of the carbonization test also increases with the amount of the sample, so that for preliminary surveys of a number of coals, samples of 25 to 1,000 grams usually are employed."

Dec 1, 1939

By S. F. Mauser

This report describes the study of factors which affect medium voltage (661 - 1000 volts) trailing cable splices used in underground coal mines. Improvements in quality, dependability, and design of splice kits and shop splices are presented in the study results and recommended guidelines and regulations. Recommended research programs are included which describe approaches for development of the recommended guidelines and regulations for medium voltage trailing cable splices. The basis for the conclusions and recommendations presented in this report is included in three appendices which describe a survey, splice examination, and general requirements development prepared during the progress of this study.

Jan 1, 1977

By William W. Adams

Accidents to men employed in the quarrying and related industries of the United States were more numerous, absolutely and relatively, in 1937 than in 1936. Fortunately, the entire increase was in the category of nonfatal injuries, as accidents causing death declined in number and in proportion to the number of man-hours worked. Employment increased. More men were employed, more man-days and man-hours were worked, and the average employee had more hours of work than in 1936. Reports covering all commercial operations showed that 84,094 men were employed an increase of 5.1 percent over 1936. The number of man-hours of work performed by the industry was, 158 millions, an increase of 7.6 percent. Seventy-seven men were killed by accidents, a, reduction of 14 from the year before, and 6,348 men were injured and disabled for more than the remainder of the day on which the accident occurred, 11 percent more than in 1936. The fatality rate of 0.49 per million man-hours of exposure in 1937 compared favorably with the rate of 0.62 for the previous year, whereas the non-fatal-injury rate of 40.10 was 3.2 percent higher than the rate of 38.87 for 1936.

Jan 1, 1940

By J. W. Miller

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and, from the data developed, to determine: (a) Which coals, either as mined or after beneficiation by conventional preparation, are suitable chemically under present standards for producing metallurgical coke. (b) Which coals require special and more intensive treatment in preparation than is now practiced. (c) Which coals cannot be considered potential sources of metallurgical coke, regardless of preparation. This report is one in a county series and describes the preparation characteristics of the coals of Logan County, W. Va. According to present-day standards for metallurgical coal, many believe that the sulfur content of the coal should not exceed 1.25 percent? Coal with more than this amount has been used for making metallurgical coke, especially when blended with coal containing less sulfur. In this series of reports 1.25 percent sulfur is used as a gage to determine whether or not a coal will be suited for metallurgical coke.

Jan 1, 1957

By R. L. Derick

On a regular basis, mine personnel should obtain air samples directly from active underground areas as well as remotely from sealed locations. These samples provide mine officials with data relative to the makeup of the various atmospheres. Should conditions underground change, these results can provide a baseline that can assist officials in determining the extent of change. Relating the concentrations of individual gases to time, applying gases to equations, and examining their change over time are tools that have been successfully used to determine if a heating event exists and, if so, the extent of the emergency. These atmospheric status equations have either been developed for the mining industry or adapted from other industries. They serve as tools to assist personnel in determining the condition of underground mine atmospheres. As long as the problem area continues to be ventilated, certain gases, gas ratios, and equations can be used to determine if a fire exists, what type of material could be burning, and what quantity of coal is burning. Once the mine or the involved section has been temporarily sealed, gases, ratios, and gas-derived equations can assist personnel in determining how conditions within the sealed volume are changing over time. To alleviate potential explosions when fresh air is once again introduced into the sealed volume, equations and a diagram have been developed to predict the likelihood of an explosive atmosphere. Similarly, prior to commencing recovery of a mine or section, equations exist that can assist in determining if the fire will rekindle when air is reintroduced. This paper serves as an overview to remind and/or instruct readers about gas-sampling methodologies and gas analyses to assist in determining the status of underground atmospheres.

By R. V. Ramani

This volume is the second of a four-volume final report on research carried out under a contract from the U.S. Bureau of Mines on the development of a computer simulation model for surface mine reclamation planning. The other volumes are titled as follows: Volume I: Ore Reserve Estimation, Volume III: Mine Coordinate Generator System, and Volume IV: User's Manual for OPMHS/2. The dragline model described in this report simulates the movement of the dragline bucket across the digging face, the swing load, the dump, and swing back. It is programmed to handle chopdown, key cut, main cut, and rehandling operations. Provisions have been made for simulating equipment and mining delays. Any mining method can be specified in terms of numbered blocks, the dragline positions for the mining block and the dumping location for the block. Accounting procedures permit the calculation of production rates, rehandle volume, dig and delay times. The model can be used to study the effects of varying mining conditions, cut width, and spoiling sequence with special reference to toxic spoil, overburden and bench removal procedures. The basic input data for the model include machine parameters, the geology and material characteristics, the mining parameter, and the delay characteristics of the equipment.

Jan 1, 1985

By K. L. Paciorek

The primary objective of this program was to determine the toxic fume and fire hazard of elastomeric noise abatement materials with a limited effort expended on the evaluation of specific treatments applied to mine timbers. Under the conditions employed, for a dimethyl silicone rubber, formaldehyde presented the major toxic threat; acrolein was the main toxic species for both polyester and polyether urethanes and an acrylonitrile-butadiene-styrene resin; in the case of flame-retardant styrene-butadiene rubber compositions, hydrogen chloride, and in the case of PFA-treated timber, furfural, were the major toxic compounds. Of the materials studied, the flame-retardant styrene-butadiene rubbers presented the greatest toxic hazard. The generated data have been reduced to toxic load tabulations amenable to employment for potential hazard assessment.

Jan 1, 1982

By J. R. Thoenen

During the past 6 years the Mining Division of the U.S. Bureau of Mines has prepared many information circulars containing valuable technical data covering the operating details of mining and ore-dressing plants throughout the United States, Canada, Mexico, and other countries. These papers, written for the most part by operating officials in the field, have been designed to comprise a reference library for the operating engineer. In order to make the information contained in these publications more readily available to the busy engineer the enclosed series of reference tables has been compiled. The tabular arrangement is by subject rather than alphabetical order, thus avoiding the bulk of an alphabetical index.

Jan 1, 1935

By T. F. Anstett

The Bureau of Mines evaluated the potential availability of chrysotile, amosite, and crocidolite asbestos from 42 properties in market economy countries. This resulted in the development of tonnage-cost relationships indicating the quantity of grades 3 through 7 asbestos at various average total costs of production at 0% and 15% rates of return on invested capital. The availability of grades 2 and 8 was also evaluated, but since each is produced at only one property, no analytical results were given. Total demonstrated recoverable chrysotile fiber potentially available of grades 3 through 7 from the 42 properties evaluated follow: 1.59 million t, 21.00 million t, 16.74 million t, 15.54 million t, and 19.27 million t, respectively. The total amount of crocidolite is 1.69 million t. Owing to the good potential for discovery and development of new deposits, long- term availability of fiber of all three types is not in jeopardy. However, many of the crocidolite properties evaluated in the northern Cape crocidolite field of South Africa have relatively small demonstrated resources, and new deposits will have to be exploited by the late 1990's to sustain projected levels of production.

Jan 1, 1985

The request for proposal from the U.S. Bureau of Mines outlined the purpose of this study in the following terms. "High grade near surface deposits are largely a matter of history. Most of the current mineral production in the united States is from large low grade ore deposits mined by large scale methods. It appears likely that exhaustion of near surface deposits and public resistance to open pit mining will tend to reverse the present trend toward open pit mining and lead to increased reliance on large scale underground mining. In view of the long lead time needed to improve basic technology, an in-depth study of the major underground mining methods is needed. "This study is intended to provide a systematic review and analysis of large scale non-coal underground mining technology with particular emphasis on current practices and problems, needed technological improvements, existing or potential environmental conflicts, and possible modifications or innovations that will assist in the satisfaction of projected national mineral supply requirements."

Jan 1, 1974

By Gregory J. Chekan

This Bureau of Mines report presents three methods for designing bulkheads to impound water underground: (1) thin and thick plate design; (2) South African plug design; and (3) single and double bulkhead seal design. Related areas critical to the long-term effectiveness of underground water impoundments are also addressed. These include bulk-head anchorage, concrete specifications and placement, the grouting of permeable strata, and the sizing of barrier pillars. A case study involving hydrostatic tests conducted on a single bulkhead seal constructed in the Safety Research Coal Mine of the Bureau's Pittsburgh Research Center is presented in an appendix.

Jan 1, 1985

By P. A. Cox

Guidelines are provided for the design of explosion-proof electrical enclosures that will meet MSHA certification requirements according to Part 18, Title 30, of the Code of Federal Regulations, and fulfill their intended service underground. The guide covers only those aspects of design which affect enclosure strength, ruggedness, endurance and flame path, i. e., the enclosure ability to properly contain an internal explosion. Internal static and explosion pressures, external impact and thermal heating load are treated as well as the proper selection of materials and welding procedures.

Jan 1, 1985

By W. W. Roepke

The Bureau of Mines has developed an interactive computer program that enables mine operators and others to identify the effect of cut-ting system changes on relative dustiness at the face. The program, which simultaneously evaluates machine parameters, coal seam parame-ters, and operator-controllable parameters, was developed for use on any microcomputer using BASIC programming language. The program allows the user to change one or more of the cutting system parameters at a time to see how these changes affect relative dustiness. A complete program listing and flowchart are included along with operating in-structions and sample outputs. An example showing how to use the program is also included.

Jan 1, 1985

Minerals are vital to any industrialized civilization. Annually, the United States uses more than 4 billion tons of new mineral materials, or about 40,000 pounds per person-about half being mineral fuels and the other half being metals and nonmetallics. Stable and economic domestic mining, mineral, metal, and mineral reclamation industries are essential to the economy. The value of United States energy and processed materials of mineral origin exceeds $200 billion annually. Although a number of minerals are imported, especially some designated as "strategic and critical," most U.S. mineral supplies are derived from the domestic mines and processing facilities that you will be seeing, reading about, and visiting as you use this visitor guide. We hope you enjoy your experiences. This pamphlet, a guide to mining and mineral operations that may be observed or visited and some other points of interest relating to minerals, is intended to aid tourists and students who are interested in mining. Some may wish to study our Nation's romantic past; others may plan to enter the minerals industry as a career; still others may have a primary interest in conservation practices. The pamphlet is also intended to aid State and local officials, Chambers of Commerce, and mining firms in answering some of the many questions of tourists and students.

Jan 1, 1977

By Leslie D. Marrus

This project and final report represent an effort to collect, analyze, and verify reliability and performance data on currently available medium -to-high seam models of continuous miners being used in underground coal mining. The analysis determined availability, mean time and tons between failures, amounts of down time associated with various failures, labor and part costs required to correct failures, and various indices of maintainability. Machine performance and reliability are discussed relative to cumulative tons (machine age) produced and production rates (machine loading). It was determined that performance can be significantly improved given preventive maintenance programs that will increase machine availability.

Jan 1, 1976

By Oliver Bowles

"Asbestos" is a name applied to a group of naturally fibrous minerals. Because it has the fibrous characteristics of silk or cotton and at the same time will not burn and has other advantageous properties as well, asbestos has specialized uses for which no adequate substitutes are yet available. Asbestos furnishes a major raw material for a great variety of essential products, the manufacture of which constitutes a vast industry. Asbestos generally occurs in irregular veins scattered throughout rock masses. Most of the fiber-bearing rock is mined in huge open-pit or underground workings. The fibers are separated from the rock and sorted into groups, according to length, in large, complex mills. The longer fibers are stripped to textile plants, where they are further fiberized and prepared in special machines and are used for spinning into yarn and weaving into unburnable cloth that has many important uses. The shorter fibers, which are much more abundant than the long ones, are used in asbestos-cement building materials in heat-insulating products and for a multitude of other applications. These processes and uses are covered in considerable detail in later sections of this report.

Jan 1, 1959