Search Documents

By G. L. Humphrey

Although thermodynamic data for ferrous oxide are among the most important in extractive metallurgy, adequate values have not been available until quite recently. The older data suffered not only from the usual experimental difficulties but especially from lack of the knowledge that ferrous oxide of stoichiometrical composition does not exist as a single, thermodynamically stable crystalline phase under any circumstances. This paper reports new experimental data on the heat of formation of ferrous oxide by two methods (combustion calorimetry and solution calorimetry), employing material of unequivocal composition. The results are compared with values obtained from data for the hydrogen reduction, carbon monoxide reduction, and disproportionation reactions of ferrous oxide, and a best value is selected. A table of heat and free energy of formation values of ferrous oxide to 2,000°K is given. These values are combined with available data for water, carbon monoxide, and carbon dioxide to obtain theoretical heats and free energies of reduction corresponding to the selected heat of formation. Hydrogen and carbon monoxide reduction equilibria are compared, and the differences in trend with temperature and the percentage utilization of the reductants are considered.

Jan 1, 1952

By George T. Krempasky

This report is one of a series of Bureau of Mines Information Circulars dealing with mining methods and costs throughout the United States. It describes drifting, crosscutting, and raising operations at several mines in the Coeur d'Alene mining district, Shoshone County, Idaho. Ore bodies in the Coeur d'Alene district are generally in steeply dipping tabular ore zones, are irregular in shape, erratic in occurrence, and have been extensively mined along the strike and down dip. Because of the extended attitude of the deposits a great deal of development work is required. Drifting, crosscutting, and raising methods are described in this report. Shaft sinking is the subject of another report in the same series.

Jan 1, 1960

By D. Harrington

Notwithstanding all the effort maa.e to introduce wet drills to prevent dustiness of air of metal-mine workint;s pl2.ces, there has during the pa.st few years arisen in Australia and South Africa an impression that wet drills, in­cluding the Leyner typa, actuali"y cause und..ue quantities of finely divided ore and rock to rise into the air, these fine particles being chiefly attached to · P=i-rticles of fog or spray escc:.ping frow holes using water drills. This fs saia. to have created consternation in the ranks of the min operators who have com­piiei With drastic wet dri llin rf,ubtions, 2nc:i. purchased and operateC1. various types of wet drills at no inconsiderable expeniiture in both money and effort.

Mar 1, 1922

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 4,680 samples, representing the products of 130 companies. The samples were collected during December 1953 and January and February 1954. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor-Gasoline Survey reports published during the past ten years is given on page 5.

Jan 1, 1954

By M. J. Ferrante

Relative enthalpies of CuBr from 298.15 to 1,301 K were measured at the Bureau of Mines to provide thermodynamic data needed for the advancement of mineral technology. The temperatures of transition were measured by differential scanning calorimetry (DSC) and the standard enthalpies of transition[ (IlH~r) by drop calorimetry. The combined results gave reversible transitions at 657 K with llH~r= 1.10 kcal/mol, at 741 K with lm~r == 0.51 kcal/mol, and at 759 K with an enthalpy of fusion (AH~) of 1.22 kcal/moL ] An anomalous increase in heat capacity preceded the first crystal transition at 657 K. Tabulated values are listed for the standard relative enthalpy, heat capacity, entropy, and Gibbs energy function from 298.15 to 1,500 K. Standard relative enthalpies are also given in equation form and combined with thermodynamic data from the literature to derive values of standard enthalpies of formation and Gibbs energies of formation.

Jan 1, 1984

By G. L. Oldright

This paper is the twelfth of a series on smelting in the lead blast furnace and the fifth dealing with blast-furnace gases. It was noted in Report of Investigations 2957 that the gases evolved from the top of the lead blast furnace at Tooele were similar in composition to those from the top of an iron blast furnace. It was noted in Report of Investigations 3095 that at Kellogg, where a smaller percentage of coke on charge and shorter stock column were employed, the gases evolved were much less reducing. At times there was a considerable amount of oxygen in the top gases at the second plant. More SO2 was also evolved from sulphides in the charge. Then operations were conducted as at Kellogg, the gases were alternately reducing and oxidizing. This paper deals with the gases evolved in smelting a charge containing more zinc than at either of the other two plants with about the same amount of coke as was used at Kellogg,: To compare other factors influencing the composition of the gases, it may be noted that at Tooele the approximate height of the charge column was 15 feet, at Kellogg 9 feet and at Trail 13 feet. The furnaces have about the -same cross-sectional area- tog. The furnaces at Tooele are about 6 inches wider at the tuyeres, being 54 inches wide against 48 for the other two plants. At Tooele and Kellogg the furnaces are fed at the top from bottom-dump cars. At Trail the charges are dumped from Decauville cars (bottom cars which dump when tilted), which run on tracks placed on both sides of the blast furnaces. The hoods through which the waste gases are conducted are directly above the shafts of the furnaces. The flues for removing the effluent gases lead off from under the charge floor at Tooele and Kellogg. (Charging and distribution of the feed in the furnace covered later in a rate paper of series.)

Jan 1, 1934

By Robert H. Ridgway

This circular outlines salient facts regarding the manganese-ore industry in the United States and the world. It is founded chiefly upon published information available in the literature of the subject. The Bureau of Mines has in its files additional, more detailed data upon many of the topics presented very briefly here, and will endeavor to assist the mineral industries and public by giving further information in response to individual inquiries. The Bureau will welcome comments, criticisms, and contributions of data that may assist in making later additions of this circular more accurate, or in developing more fully its mineral files pertaining to manganese. In reporting the production of manganese-bearing ores in the United States the following classification has been adopted by the Bureau of Mines: (1) Metallurgical-grade ores, under which have been classified manganese ores containing 35 percent or more of manganese used in the manufacture of iron and steel, ferruginous manganese ore containing 10 to 35 percent of manganese, manganiferous iron ore containing 5 to 10 percent of manganese, and manganiferous zinc residuum; (2) battery ore; (3) fluxing ores, under which are classified ores that may contain a few ounces of silver and are rich enough in manganese to make them valuable chiefly for fluxing purposes in nonferrous smelters; and (4) miscellaneous ores, under which are classified the ores shipped to brick manufacturers, glass makers, and manufacturers of manganese chemicals.

Jan 1, 1933

By Wing G. Agnew

The first six Reports of Investigations in this series , pertaining to the investigation of stemming at the Mount Weather Testing Adit, dealt with ( 1 ) the dust produced by blasting , ( 2) the effect of stemming upon gases generated by blasting , ( 3 ) the relative advantages and disadvantages of different types of stemming and no stemming when used with 60 - percent ammonia gelatin dynamite , (4) the length of stemming material through which a primer will fire and detonate a charge of dynamite , ( 5) comparison of dust and gases produced when blasting charges of dynamite in drill holes , bombs, and mud - cap shots , and ( 6 ) the relative advantages and disadvantages of different types of stemming and no stemming when used with 40 - percent ammonia gelatin dynamite .

Oct 1, 1943

By J. W. Town

The Bureau of Mines made continuous-circuit beneficiation studies to determine the optimum conditions for concentrating phosphate minerals from the intermediate-and marginal-grade ores of the Phosphoria Formation in southeast Idaho. Intermediate-grade ore was represented by a sample from Georgetown Canyon and marginal-grade ore from the Gay mine near Fort Hall. Two flow-sheets were developed: The first involved roasting, attrition scrubbing, sizing to remove a concentrate, grinding of the oversize, des liming, and flotation; in the other flowsheet roasting was eliminated. Controlled attrition scrubbing was used to remove clay and silt-size quartz particles imbedded in the phosphate pellets without breaking the pellets. The minus 35-plus 200-mesh fraction was removed by sizing as a finished acid-grade concentrate. The plus 35-mesh material was ground in a rodmill to minus 35 mesh and recycled to the attrition scrubber. The minus 200-mesh fraction was des limed at about 800 mesh to remove clay slimes and floated with 3 to 4 pounds of emulsion per ton of feed. The aqueous fatty-acid oil emulsion consisted by weight of 3 parts No.2 diesel oil, 3 parts crude tall oil, and 0.5 part water-soluble petroleum sulfonate.

Jan 1, 1967

By Gerald W. Elger

To determine the feasibility of removing nonferrous metal impurities from automobile scrap by thermal treatment in a rotary kiln, the Bureau of Mines conducted four series of tests with synthetic scrap mixtures heated at various temperatures under oxidizing and reducing conditions. The treated scrap mixtures were melted in an electric-arc furnace and cast into small ingots for impurity evaluation. Analyses showed that the ingots were essentially free of residual metal impurities except for copper. Test data indicated that in an oxidizing atmosphere the percentage of copper removed increased with treatment temperature. Percent of copper removed in a reducing atmosphere was found not to be temperature dependent. A significant finding was that copper was embrittled under some of the operating conditions and was mechanically removed by fragmentation.

Jan 1, 1968

By H. E. Powell

A laboratory mineral-dressing investigation was conducted by the Federal Bureau of Mines on four limonitic and four sideritic iron ores from the North Basin of the east Texas iron-ore district. The samples, composited from drill cores, were considered representative of the iron-ore reserves of the area. The objectives of this research were twofold: (1) To devise a mineral-dressing method whereby the yield from currently mined east Texas iron ores might be increased and the grade improved, and (2) to extend such treatment to include the lower grade ferruginous materials that are not amenable to beneficiation by simple washing and, therefore, are not being exploited. Of the mineral-dressing methods used in this investigation, magnetic separation of roasted are was shown to be the most effective. Results show that, by this method, a laboratory recovery of 82 percent of the iron is attainable at a grade surpassing that obtained by current plant practice and that both limonite and siderite are amenable to concentration by the process. The existence of large deposits of iron are in eastern Texas has been recognized for over 100 years. These ores were first exploited during the Civil War and were mined intermittently until about 1911. From that time until 1944 when the Defense Plant Corporation financed the erection of three blast furnaces to use these east Texas ores, production was almost at a standstill.4/

Jan 1, 1960

By Stella Sigler

This publication contains analyses and related source data for 153 natural gas samples from 16 States. Of the total samples, 149 were collected during calendar year 1993. The remainder were collected earlier, but releases granting permission to publish were not received until 1993. None of the analyses have been previously published in annual reports. All samples were obtained and analyzed as part of U.S. Department of the Interior, U.S. Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1994

By James W. Townsend

[The Harrington-Hickory mine in the Star raining district, Beaver County, Utah, has produced approximately 20,000 tons of lead-zinc-silver ores since 1910. Production previous to 1910 is not known. The mine is owned by the New Majestic Mining Co. The property was rehabilitated and operated by James D. Williams under a 10-year lease with option to purchase from April 1943 to May 1949, Loans from the Reconstruction Finance Corporation in the aggregate of $41,000 wore used in construction of an access road, rehabilitation of the mine, and purchase of equipment for full-scale operation. The improved, all-weather access road extends from loading ramps on the Union Pacific Railroad at Milord to the urine storage bins 5 miles west o f town. The mine is serviced electrically by a. 5,000-volt line owned by Telluride Power Co. Mine transformers step the voltage down to 440/220/110 for surface and underground service.]

Jan 1, 1953

By J. M. Kuchta

Concentrated hydrogen peroxide (H202) is a highly reactive oxidizing agent that liberates heat when it decomposes. The heat liberated may be sufficient to ignite combustibles with which the peroxide comes in contact. For this reason, concentrated hydrogen peroxide should be handled only by personnel familiar with its many unique properties.6 Hydrogen peroxide is used as a bleaching agent in the manufacture of textiles; this is its major single use in the United States. It is also employed as a reagent in chemical synthesis, as a source of free radicals to start polymerization, as a foaming agent in the manufacture of porous substances, and for its effect on biological processes. Moreover, highly concentrated hydrogen peroxide is a compact source of energy that can be utilized both as a monopropellant and as the oxidizer in a bipropellant system, During World War II, large quantities of highly concentrated hydro- gen peroxide were used as propellants, particularly in Germany. Since then, production of the peroxide has increased rapidly; in the United States alone it has more than doubled since 1950.7 Because of its widespread use, increasing interest has been shown in the hazards of handling the high- strength peroxide.

Jan 1, 1961

By R. R. Lowery

The Bureau of Mines developed hypereutectic aluminum-silicon alloys which 11.7.d better mechanical properties than the unmodified hypereutectic alloy. A commercial aluminum-20 weight-percent silicon LIr alloy was selected as a ary base for improvement. The primary silicon. grains were reduced from ASTM 4-5 to ASTM 8.5 by the use of phosphorus and phosphorus compounds. The remaining eutectic matrix was refined by sodium metal additions of 0.2 weight-percent. Solid solution strengthening of the alpha aluminum was obtained by adding 2 percent copper and 0.5 percent magnesium. Also, 1 percent nickel was added to harden the alloy. Optimum thermal treatment consisted of a solution treatment for 10 hour:, at 480° C with hot water quench, followed by aging for 6 hours at 175° C. The final alloy exhibited a Rockwell B hardness of 75 ±2 in the heat-treated condition. The ultimate tensile strength was 39,5O0 psi with no recordable elongation. The coefficient of linear thermal expansion was 20.4 x 10-6 per °C in the temperature range 20° to 300° C. No wear resistance data were collected.

Jan 1, 1966

By John B. Goodman

This report summarizes the work done by the Koppers Company, Incorporated, in cooperation with the Bureau of Mines on the commercial evaluation of the primary low-temperature tars produced from Texas lignite in the Rockdale, Tex., plant of the Aluminum Company of America in conjunction with the Texas Power and Light Company. The interest of the Bureau of Mines in this project is twofold. First, through its cooperative agreement with the Texas Power and Light Company the Bureau has assisted in the technical design and practical operation of the prototype, externally heated, entrained-state carbonizer for producing char for electric-power production and for primary low-temperature tar. Second, the first successful operation of the prototype carbonizers employing the Bureau of Mines-Parry process on lignitic coal in 1953-54 led to the production of large quantities of primary lignitic tar, concerning which too little was known or had heretofore been published in this country.

Jan 1, 1959

By Wallace W. Roepke

The Bureau of Mines tested new designs of drag bit cutters with sintered diamond inserts instead of standard tungsten carbide tips. The bits were tested for orthogonal cutting forces, primary dust generation, and incendivity, with a standard plumb-bob type conical cutter (600 included tip angle) as the reference. Preliminary wear and impact-failure testing were also done. The results were mixed. Two new designs had forces similar to those of the reference bit, but one new design had about twice the normal force. This same design had almost twice the specific energy during shallow cutting but generated an equal or slightly lower amount of primary dust than did the reference bit. Incendivity was eliminated for two radial designs. One conical design had ignition only after more than 15 impacts, but the other conical design was incendive. Impact failure occurred, but not so quickly as anticipated. Over 7,500 impacts on a sandstone face, with a total cutting distance of more than 1,981.2 m, only scuffed the leading edge of the sintered diamond cutting face but put hairline cracks in the substrate mounting pad. Additional design and testing are needed to develop an optimum cutter, but prospects look good for this material.

Jan 1, 1983

By E. R. Palowitch, A. W. Deurbrouck

The Bureau of Mines reviewed available data on the effect of crushing high - sulfur coals for the liberation of impurities in the light of increasingly stringent air pollution regulations . The survey , which provided information on Appalachian region coals only , indicated that such important coalbeds as the Upper and Lower Freeport and the Upper Kittanning show significant sulfur reductions when crushed to 14 - mesh top size . For many other coalbeds amenability to sulfur liberation by crushing was indicated , although too few samples were available to draw firm conclusions .

Jan 1, 1966

By D. L. Sawyer

The Bureau of Mines studied alumina extraction from uncalcined, kao-linitic clay at temperatures from 1000 to 2500 C using 20-or 27-wt-pct-HCI concentrations and with an acid-to-clay ratio of from 0.8 to 1.4 times stoichiometric. Autogenous digestion pressures ranged from atmospheric pressure to about 900 psia. Extraction of 96 pct of the alumina was obtained by HCI leaching at temperatures and leaching times that varied from 1000 C for 120 h to 2000 C for 15 min. Hydrochloric acid stoichiometry of the reaction A1203'2Si02'2H20 + 6HCI + 2AICl3 + 2Si02 + 5H20 was studied at different temperatures and leaching times in a 750-mL tetrafluoroethylene-polymer-lined autoclave. A combination of high temperature and 20 wt pct excess HCI promoted rapid and almost quantitative extraction of alumina (99 pct in some tests). Additional Bureau data obtained with 35-mL tantalum bombs and leach-ing tests with added fluoride are also provided. At high temperatures, the addition of fluoride did not result in a significant improvement over HCI alone and was deleterious to the filtering properties of the digest residue.

Jan 1, 1985

By PHILIP A. ZANG

The rapidly increasing use of motor vehicles in the United States has introduced an entirely new problem in the proper ventilation oftunnels , subways , and other confined spaces through which such machines must pass . This problem was brought to the attention of the Bureau of Mines by the New York and New Jersey State Bridge and Tunnel Commissions with reference to the ventilation of the proposed vehicular tunnel under the Hudson River . This tunnel , consisting of twin tubes 29 feet in diameter and 8500 feet long between entrance and exit , presented an unprecedented problem in ventilation both on account of its length and on account of the traffic density , which is expected to reach a maximum of 1900 vehicles per hour . An exhaustive study by the tunnel engineers of all available data on the amount and composition of automobile exhaust gas disclosed very little information on the percentage of carbon monoxide in motor exhaust gas from the average run of automobiles and trucks under actual operating conditions on the road. It was well known that carburetor adjustment and other operating factors changed the percentage of the poisonous constituent , carbon monoxide , from practically 0 to 12 or 13 per cent ; but no safe estimate could be made of the most probable figure without further investigation .

Mar 1, 1921