Search Documents

By George H. Popper

The Bureau of Mines has evaluated the extent of phosphate resources available for recovery by the experimental borehole mining method in the Southeastern Coastal Plain of the United States- Phosphate re- sources at overburden depths greater than 30 m are as a rule currently unsuitable for recovery through conventional mining methods because of economic, environmental, or technical considerations. In the identified deposit areas, borehole mining operations are projected to yield a more favorable rate of return and to be environmentally more desirable than conventional surface mining. Borehole mining resource estimates presented in this study are preliminary and designed to serve as a basis for future resource evaluations, as the current data base is relatively sparse and incomplete. The resulting resources have, therefore, been classified as hypothetical and speculative and are subject to up- dating as additional exploratory data become available. Hypothetical and speculative resources amenable to borehole mining are estimated to total about 385 billion metric tons (rat) of phosphate matrix with a minimum in situ grade of 5 pct P205. With projected borehole mining capabilities and current conventional beneficiation procedures, this resource would make available approximately 64 billion mt of phosphate rock product at an estimated grade of 30 pct P205.

Jan 1, 1985

By K. Robert Dorman

Spray-applied polyurethane foam was used to insulate the walls of heated rooms excavated in permafrost. The experiment was designed to determine whether polyurethane foam can be sprayed successfully on frozen ground under freezing conditions and to measure the effectiveness of the insulation in maintaining--at elevated temperatures for an extended period--a room excavated in frozen ground. Two manufacturers' foams were investigated in the laboratory. Subsequently, one of the foams was employed to insulate two small rooms, one in frozen gravel and one in frozen silt, in an experimental tunnel belonging to the U.S. Army Cold Regions Research and Engineering Laboratory (USACRREL) near Fairbanks, Alaska. Following insulation, heat was introduced into the two rooms. Heat migration across the insulating barrier into the walls, in addition to wall closures, was monitored over an 8-month period. The results show that polyurethane foam can be successfully sprayed on frozen ground in below-freezing temperatures. Given this type of insulation, together with winter cold to supercool the surrounding ground, it should be possible to maintain a shaft or heated room in permafrost for several years.

Jan 1, 1970

By John W. Buch

In 1947, a Korfmann universal shearing machine was installed in a mine in the Southern field of the Pennsylvania anthracite region. The machine was obtained from Germany by the Bureau of Mines after the close of World War II as a part of a program of experimental work to increase the output and lower the cost of anthracite, which the Bureau of Mines initiated in 1944 when an agreement was made with an anthracite-producing company for use of one of the company's mines as a testing ground for certain mechanical equipment procured or developed by the Bureau. A major objective is to develop a mechanical mining method that will increase the rate of advance and reduce the coat of development of coal gangways in steeply pitching seams. In addition to the time to be saved in driving these openings by machine, it is felt that further economies will be affected by making it possible to concentrate producing sections into smaller compass and that savings will ensue in supervision, maintenance, and time required for mining a section. A higher percentage extraction also is an objective. Test work covered by this report was concentrated on the power characteristics, maneuverability, effectiveness, and general qualities of the Korfmann machine in cutting coal, the cutting tests representing the first use of a machine of this kind in steep-pitch mining in the United States.

Jan 1, 1951

A symposium on the health hazards of respirable dust in the mining and milling of talc was held on May 8, 1973, in Washington, D.C. The results of medical effects on both human and animal subjects were presented. Methods for identification and classification of talc minerals were also presented. Analytical techniques discussed included X-ray diffraction, scanning electron microscope observation, electron probe, and optical microscopy.

Jan 1, 1974

By G. D. Coe

Float-and-sink tests indicate what results are obtainable by gravity separation and rare therefore an invaluable adjunct to most coal-cleaning processes. However, it is difficult to make a direct interpretation of float-and-sink data on coal, and several systems for interpreting them have been proposed. Of these, that developed and used extensively by Bird3/, Yancey4/, and Gandrud5/ is considered by the author to be the most satisfactory. It makes use of four interrelated curves (hereafter referred to as be "washability curves"). These curves were explained by Bird in a paper6/ published in 1923, but his explanation has been regarded by some as not sufficiently

Jan 1, 1938

By Larry R. Wilson

The development effort described herein was directed toward the design and development of a flexible communication system to provide two-way section communications between any telephone on an MCM-101 telephone FDM exchange and a miner provided with a uhf walkie-talkie transceiver. The system also provides normal communication between miners within a working section through the uhf coupler interface repeater.

Jan 1, 1976

By E. P. Carman

In this report, the Federal Bureau of Mines presents a summary of the occurrence, properties, and uses of some natural bitumens, using the layman's or dictionary definition of bitumens - that is, naturally occurring hydro-carbons. Emphasis is on the less common solid and semisolid bitumens, particularly those occurring or used to some extent in the United States. This comprises data from many sources and references to these sources for more detail than is given in this summary. This paper was prepared primarily to answer questions about some of the less known bituminous materials. The word hydrocarbons could just as well have been substituted in the title for bitumens, but bitumens was used, since an abstract of the paper was presented at a meeting where the major emphasis was on bituminous materials. The reader will realize that coals, of which only the more unusual such as the cannel coals and torbanites are discussed in this paper, are primarily mixtures of bituminous materials and carbon. The amount of bituminous material, or volatile matter, in coals is greatest in the lower rank coals and the unusual types described in this paper, and decreases as coal rank increases. However, since no method other than destruction of the original coal substance by heat is known that will separate the volatile matter from the carbon, it appears reasonable to classify the coals with other bituminous materials, particularly since bituminous coal - the most widely used coal - by its name indicates the combination of bituminous materials and carbon.

Jan 1, 1961

By K. P. Wang

SIGNIFICANT general developments took place in the Far East during 1964, with far-reaching repercussions on the mineral and industrial economies of individual countries and the region as a whole. Japan, during this, "the Year of the Open Door," ushered in the era of industrial maturity, greater independence in economic policy, and expanded technical assistance to less developed countries. Symbolic of its dynamic economic growth is the fact that Japan out-produced the Federal Republic of Germany in steel during 1964 to take over a third-ranking world position. Mainland China, recovering from the "Leap Forward" debacle, made significant gains in industrial output. Mainland Chinese trade with Japan was on the upswing, and discussions were held between the Chinese and the Soviets for possibly resuming Soviet aid in industrial and mineral development. Meanwhile, United States aid to Taiwan was being phased out because of progress achieved. Rapprochement between South Korea and Japan was imminent late in 1964, a factor which may well affect South Korean mineral development. The Indonesian-Malaysian confrontation created economic difficulties in both countries. The war in Viet-Nam seriously disrupted industrial activities, particularly in the south.

Jan 1, 1966

By R. S. Olsen

The Bureau of Mines is engaged in research to recover aluminum from kaolinitic clay and other nonbauxitic domestic resources. As part of this work, calcined Georgia kaolin was prepared by a process that prevents slime formation and makes the leached residues fast settling and easy to filter. The leaching reaction for calcined kaolinitic clay in a 5 pct stoichiometric excess of boiling 23-to 26-pct HCI was found to be zero order. Rate constants based on the weight-fraction of aluminum in the clay were found to be between 0.095 and 0.15 min-1 depending on feed preparation and leaching parameters. The mathematical relationships between aluminum extraction and time for both batch and continuous, stirred-tank operations were derived and verified experimentally.

Jan 1, 1983

By Robert A. Speirer, Richard G. Burdick

Methods of detecting geologic faults and other linear features by means of processed LANDSAT satellite images have gained prominence during the past several years . There have been numerous programs written to pick these " lineaments , " but they have been almost universally tailored to large computers . This Bureau of Mines report describes a detection method developed for use with a minicomputer . The method comprises a suite of programs that scans an image for all " potential " lineaments . From this partially analyzed data , the final lineaments are picked by another routine . The method was field tested in an area of south- central Wyoming , and results indicated good agreement between computer- picked lineaments and ground features . Most of the known geologic faults in the area were picked by the method . Such features as roads and trails were also picked but were easily distinguished from faults during field inspection . The method is relatively new but promises to be a viable reconnaissance technique for the mining industry in geologic structural analysis .

Jan 1, 1965

By Lewis M. McNay

Description of methods employed and cost data are given for surface-mined land reclamation in Moraine State Park, Butler County, Pa. This project was conducted under the authority of the Appalachian Regional Development Act; a total of 177 acres of land was rehabilitated for specific land use purposes. The use of large equipment expedited the project work, and similar results could be anticipated on similar reclamation programs.

Jan 1, 1970

By D. G. Puglio

This Bureau of Mines study covers 25 underground mines that were active in the Upper and Lower Freeport and Lower Kittanning coalbeds in 1976. The coal ranges from low to medium volatile in rank; its primary use is for steam generation. Seven mines emit more than 100,000 cfd of methane gas; those mines are the deepest and largest producers. The methane gas content of three core samples of the Lower Kittanning coalbed was estimated by the direct method. A sample from a depth of 320 feet contained 0.5 cu cm of gas per gram, at 620 feet there was 0.8 cu cm of gas per gram, and at 1,060 feet there was 11 cu cm of gas per gram. These results suggest that methane control problems will be encountered in the future as deeper coal is mined.

Jan 1, 1979

By Paul L. Russell

This property has been examined several times in the last few years , and findings have been reported . In the fall of 1942 , the author supervised sampling both lode and placer deposits . The ore was beneficiated , and the results obtained are incorporated in this report . stia The Morgan Group , which comprises seven unpatented mining claims and the Black Cat placer claims , was purchased by the Manganese Products Corp. from H. D. Hill of Hatch , N. Mex . , and Dr. A. C. White of Hot Springs , N. Mex . Arthur L. McRowe , 876 27th Avenue , San Francisco , is president of the corporation , and David Fewer, 824 Times Building, Long Beach, is treasurer . J. T. Murray is in charge of operations .

Feb 1, 1947

By W. P. Yang, L. B. Berger, G. W. Jones

"Any burning carbonaceous material, unless supplied with enough oxygen for complete combustion, will liberate carbon monoxide. Since tobacco in its many different forms consists largely of carbonaceous material, and duo to the conditions under which it is smoked (burned), carbon monoxide should be liberated. That this is true has been shown by Armstrong.***** who found that undiluted smoke from cigars contained in some tests more than 3.00 per cent carbon monoxide, the amount present depending upon the size and closeness of packing of the tobacco during manufacture and on the rate of burning.****** Cigarets gave much less CO, varying from 0.06 to 1.40 per cent. The rate of consumption and carbon content of the tobacco are not g.ven, so that a correlation of the values reported to conditions in closed spaces where people might be assembled are difficult, if not impossible.The Bureau of Mines is interested in the general question of carbon-monoxide hazards from tobacco smoke, mainly with regard to mine ventilation. In non-gaseous mines, especially metal mines, the question arises, whether, if groups of miners are permitted to smoke while working at unventilated faces or entries, would the accumulation of tobacco smoke in these places create an' additional hazards the to carbon-monoxide poisoning. The results should, in addition be of general interest in connection with ventilation of building and inclosed places where people may be assembled and smoking is permitted. The investigation described in this report was made with the above idea in view."

Oct 1, 1923

By Lloyd Williams, James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limes tone- dolomi te beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Nov 1, 1964

By W. L. Staker

The Bureau of Mines investigated the use of shredded automobile scrap for copper cementation. Air agitation was used to improve the cementation rate and prevent excessive buildup of copper on the iron. The pieces of scrap were too large to be properly evaluated in the laboratory; therefore, a pilot scale test unit was constructed and the process tested at field locations. Pregnant solution was obtained from industrial leaching operations, processed in the test unit and the barren solution and cement copper were returned to the plant process stream. The test results showed that the air-agitated launder containing auto-mobile scrap was an effective means for recovering copper from leach solutions. A continuous l4-day test run was made without a noticeable decrease in cementation efficiency. The most suitable scrap product was obtained from incinerated automobile hulks shredded in a hammer type of shredder. However, it was necessary to remove small pieces such as nuts and bolts because they interfered with the discharge of the copper product.

Jan 1, 1976

By Richard F. Link

A statistical technique, useful to analyze assay and other data characterized by location in three dimensions, is described in this Bureau of Mines report. If present, trends in the data are defined for the purposes of improving ore estimation, predicting ore beyond existing workings, and aiding geological interpretation. The technique is to fit linear and quadratic polynomial equations to the data through the statistical method of regression analysis. The fitted linear equations have the geometric form of hyperplanes; the fitted quadratic equations have the geometric form of ellipsoids or elliptic hyperboloids of one or two sheets. To visualize these three-dimensional forms, contour maps of a series of plane sections through the fitted surfaces are plotted. Both the fitting of the polynomial equations and the plotting of the con-tour maps are done by electronic computer to facilitate calculations and to obtain accurate results. Computer programs are described in appendixes. Methods employed are illustrated by an example analysis) based on data from a part of the Fresnillo mine) Zacatecas, Mexico.

Jan 1, 1966

By E. Morrice

This report of the Federal Bureau of Mines presents a laboratory procedure, with the requisite equipment, for electrowinning ingot (liquid) cerium metal from a fused-fluoride bath, the metal purity being about 99.9 percent. Physicochemical studies, including bath properties and electrochemistry, are included, with a speculative model of the mechanisms involved. An historical review of the methods used for electrowinning misch metals and yttrim-group metals, as well as individual rare-earth metals, is presented. The electrolytic preparation of metal from fused salt and nonaqueous media is summarized, along with the unsuccessful attempts at depositing the metals from aqueous solutions.

Jan 1, 1961

By Wilton Johnson

Native asphalt was produced in 1981 by five companies in three States, Alabama, Texas, and Utah. Texas was the leading State in production of native asphalt. Total production increased in 1981 to 1.26 million tons, while value increased 10.5% to $27.7 million. Bituminous limestone, used primarily for street and road repair, was produced by Whites Uvalde Mines and Uvalde Rock Asphalt Co., both in Uvalde County, Tex., and Southern Stone Co., Colbert County, Ala. Gilsonite was produced by American Gilsonite Co., Uinta County, Utah, and Ziegler Chemical and Mineral Corp., Weber County, Utah. This material was used for purposes other than road repair.

Jan 1, 1982

By Stephen W. Lambert

The Bureau of Mines examined the wellbore of a vertical gas drainage well in the Mary Lee coalbed to determine the results of specific completion procedures in coal. A jet-slotting tool was used to cut four vertical slots through the casing about 1 ft below the coalbed. Even though stimulation treatment pressure was excessive, hydraulically induced channels were contained entirely within the target coal zone. Sand-filled, induced channels were horizontal, inclined, and vertical, and were propagated in directions similar to bedding planes, rock joint, and coal cleat directions measured in the mine. Variable gas flow rates, recorded during the productive life of the well, were attributed to chronic downhole pump malfunction and the slotted casing below the production zone.

Jan 1, 1978