Search Documents

By A. C. Johnson

This paper is one of a series being prepared by the Bureau of Mines on exploration, development, mining methods and costs at various mines in the United States. It describes such methods at the Lincoln tungsten mine of the Wah Chang Mining Corp., Lincoln County, Nev. The purpose of these reports is to promote development and conservation of our mineral resources by disseminating technologic information on mining methods, practices and costs. The Lincoln mine in Lincoln County, Nev., in the southeastern part of the [tate], was acquired by the Wah Chang Mining Corp., in April 1951. Mining methods and costs are of special interest at this property because of the low costs and good production record achieved through a well planned program of exploration, development, and exploitation. Operations were discontinued in July 1957 after the Federal Government suspended the tungsten purchase program.

Jan 1, 1959

By Homor N. McDonald, G. Dale Coe, Will H. Coghill

"INTRODUCTION Sporadic beneficiation tests have been made on the Birmingham (Ala.) red iron ores for the last 55 years. Now, gravity-concentration plants are in operation, of tables are in use. A major problem, as seen by the present writers, is to obtain a coarser concentrate and add to the recovery without increasing the quantity of slime. The oily practicable solution found so far is to recover, by means of concentration (hydraulic) classifiers, the coarse concentrate normally lost in the table middling and, by a similar method, to recover middling particles from the table tailings The size and shape of the coarse concentrate Particles combine to cause them to report in the table middling rather than in the table concentrate. Similarly, mineral is lost in the tailing. Because of this, the nature of the ore, the deportment jerking table, plant tests on classifiers and tables, and the suitability of small concentration classifiers to treat table zonal middlings are discussed herein.The work was done by the Southern Experiment Station, Bureau of Mines, in cooperation with the University of Alabama, Tuscaloosa, Ala."

Jan 1, 1935

By Russell R. Trengove

In order to extend or delimit the known ore reserves adjacent to the Comet Coalition property on the western slope of the Highland Peak Range about 8 airline miles west of Pioche, Nev., the Bureau of Mines undertook an exploration project of diamond drilling. Production figures from this property, formerly known as the Schodde, are not available, but it has been reported that small amounts of rich silver and gold ore were Shipped by wagon to a smelter in the Salt Lake valley during 1900-1910. Small shipments were reported for the period 1915-1927, also. A study of the Pioche District by the Federal Geological Survey in 1942 and 1943 was the basis for the exploration program of the Bureau of Mines in 1947 This program consisted of diamond-drilling three holes. The total footage was 2,967 feet. No. 1 hole was drilled 1,260 feet, a record depth for diamond drilling in the Pioche District. Silver-bearing lead-zinc sulfide ores are found in the Combined Metals limestone, known locally as the C.M. bed, These deposits have been formed by replacement of the limestone that is inclosed in the Pioche shale.

Jan 1, 1949

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Colombia has been prepared from the best available information in Washington, but is released subject to correction and amplification; if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State. SYNOPSIS OF LAW Minerals in Colombia belong to the owner of the soil unless otherwise provided in the law. The following lands and deposits, however, are described as fiscal property of the State: Class 1. The public lands, mines, and salines which belong to the individual States (now Departments) prier to the adoption of the present constitution (1886).

Jan 1, 1929

By David Schlain

IN 1942 the Bureau of Mines began to develop the Kroll process for use in the large-scale production of titanium. Titanium and titanium alloys are now commercial metals. These metals are relatively expensive, but It is now evident that they will have important industrial uses and that in many instances these will be related to their remarkable corrosion resistance. This bulletin presents the known corrosion properties of titanium and its alloys in useful form. In marine environments titanium is highly resistant to corrosion and does not pit, or undergo crevice corrosion, stress corrosion, or corrosion fatigue. Titanium is also highly resistant in many salt solutions, including most chlorides. It is very resistant to corrosion in nitric acid solutions. It is also resistant to white fuming nitric acid. However, it may react violently with red fuming nitric acid. In phosphoric acid solutions titanium has rela¬tively good resistance to corrosion, but it has less resistance to sulfuric acid and still less to hydrochloric acid solutions. Titanium corrodes very rapidly in hydrofluoric acid Solutions. It is very resistant to corrosion in many organic chemicals. However, it has only moderate resistance to formic acid solutions and poor resistance inn oxalic acid solutions. Titanium does not corrode in dichloroaretic acid but, corrodes rapidly in 100 percent trichloroacetic acid at 100° C. Titanium is resistant to barium, calcium, magnesium, ammonium, and sodium hydroxides. Titanium is inert in wet chlorine, bromine, or iodine gases. However, in dry chlorine gas titanium reacts rapidly enough to ignite. It also reacts rapidly with dry bromine gas, but, it is resistant to dry iodine gas. When titanium is exposed to red fuming nitric acid solutions with high nitrogen dioxide content and low water content, it corrodes, undergoes stress-corrosion cracking, and becomes pyrophoric. This occurs more readily with some titanium alleys, such as titanium-8 percent manganese. A fresh titanium surface immersed in water or in an aqueous solution and in contact with an oxygen-rich atmosphere under sufficientt pressure is unstable and will ignite spontaneously. Inherently an active metal, titanium has a tendency to become less active in environments containing oxidizing agents such as air, oxygen, chlorine, or ferric, cupric, or platinic ions. Titanium is more noble than most structural metals in roost, environments and its excellent corrosion resistance is generally not, affected by contact with these metals. However, some of the other metals corrode faster because of contact with titanium. Titanium undergoes anodic polarization readily, so that even when it is the less noble member of a galvanic couple it may corrode less because of the contact. Titanium alloys often have corrosion properties and electrochemical characteristics similar to those of commercially pure titanium. Titanium alloys containing noble metals, zirconium, molybdenum, vanadium, tantalum, or copper sometimes have better corrosion resistance than pure titanium.

Jan 1, 1964

[In selecting deposits of exploration projects, tabular deposits or large mineralized masses are favored because they may be explored systematically and because they afford the best opportunity for blocking out reserves in advance of mining, whereas irregular, small pipes and scattered]

Jan 1, 1941

[In selecting deposits for exploration projects, tabular deposits or large mineralized masses are favored because they may be explored systematically and because they afford the best opportunity for blocking out reserves in advance of mining whereas irregular, small pipes and scattered]

Jan 1, 1941

By Charles D. Litton

A new prototype ionization-attachment fire detector was developed by the Bureau of Mines for detecting combustion-generated submicrometer particulates. It is much more sensitive than the conventional ionization smoke detector, and it has the following added features: 1. A primary charging current of unipolar air ions is generated by a gold-coated, radioactive center electrode of a cylindrical diode. 2. Submicrometer particulates are flowed axially through the unipolar cloud where they acquire charge. The charged particles impinge upon a third electrode, located downstream, resulting in a current which is directly proportional to the particulate concentration. 3. Additional electrodes analyze the particulates in terms of their mobility and thus determine their size distribution. 4. A filter and cyclone assembly protect the ionization chamber against ambient dust. An analysis of conventional ionization smoke detector performance is also presented in terms of source strength, chamber geometry, and applied potential.

Jan 1, 1977

By John F. Papp

International and U.S. chromium material flow, losses, and environmental releases and transfers from mining through industrial processing, end use, and recycling are identified and quantified. Average (1983-92) U.S. consumption has been: metallurgical industry, 87 pct; chemical industry, 10 pet; and refractory industry, 3 pct. Average chromium content of aluminum, cobalt, copper, nickel, and titanium alloys and alloy, carbon, and stainless steel alloys was estimated. Anthropogenic chromium consumption was estimated for the cement and copper industries. N on-commodity cycle anthropogenic chromium mobilization resulting from U.S. fuel and fertilizer use was estimated. Commodity cycle anthropogenic world chromium loss from mining and primary consumer industry was estimated to be equivalent to about 56 pct of chromium contained in chromite ore production and represented a loss rate of 181 kt-Cr/Mt-CrOre. Chromium released to the atmosphere from natural and from anthropogenic sources were comparable in magnitude. Chromium released to soil was mostly from anthropogenic sources, and aquatic releases were all anthropogenic. Domestic product chromium losses exceed process losses by more than a factor of 10 showing the importance and potential environmental impact of post-consumer recycling. The location of historical and current domestic chromium industry processing sites in 23 States were reported. Chromium releases and transfers to the environment were estimated from 1973 through 2002 by primary consumer industry. A decrease in chromium releases and transfers to the environment was anticipated.

Jan 1, 1995

By Jimmie C. Rosenbruch

The Federal Bureau of Mines evaluated the prospects for using geothermal energy to generate electricity for mines in remote areas. Given the development of a geothermal resource for this purpose, the subsidiary uses of space heating and agriculture were then examined to see if other industries might be viable given a cheap source of heat energy. Sites investigated were located in three areas of Alaska: Kobuk in the northwest, Unalaska in the southwest, and Stikine River in the southeast. Each site was relatively close to mineral deposits whose prospects for development would be enhanced with cheap power.

Jan 1, 1975

By Gordon T. Austin

The combined value of production of natural abrasives, which include tripoli, special silica stone, garnet, staurolite, and emery, decreased about 24% in 1992. The decrease in the value of tripoli production was the result of a decrease in total production. Emery decreased owing to a decrease in the volume of the material produced. Special silica stone experienced a significant increase in unit value and decrease in the quantity produced. Garnet showed a 6 % increase in quantity and a 36 % decrease in unit value. Staurolite decreased about 27 % in the quantity produced and value compared with those of 1991. The fused aluminum oxide industry showed a slight increase in the quantity produced and a 4 % increase in the value of production. The silicon carbide industry saw a 7 % increase in the quantity produced and a 10 % increase in the value of production. Combined, the industries increased 4 % in quantity and 6 % in value compared with those of 1991.

Jan 1, 1992

By Lance R. Barron

Over the past decade, the U.S. Bureau of Mines (USBM) has studied longwall gate road stability at four mines in the Book Cliffs and Wasatch Plateau Coalfields of Utah. These operations are characterized by multiple-seam mining, abruptly varying cover depths to 914 m (3;000 ft), and massive rigid, sandstone units in the main roof or floor. Such conditions encourage severe bumping, roof instability, and occasional floor heave problems.' Various gate road configurations have been employed to alleviate' these problems. Although the mines have comparable basic conditions, the lithologies and qualities of the immediate roof, floor; and seam ate different in each mine and often vary in a single mine. Gate road systems that mitigate hazards in one mine may prove inappropriate in another or for different areas of the same mine. This report relates the geology of the coalfields; describes the location, geologic setting, specific mining conditions, operating history, and the USBM field study and results or conclusions for each mine; summarizes the relative performance of the gate road systems; and emphasizes the need for site-specific geotechnical data to evaluate gate road conditions and performance.

Jan 1, 1994

By Staton L. Tainter

"The Johnny Bull and Silver Knight claims were selected for exploratory diamond drilling after having been examined by the Bureau of Mines 3./The property was considered attractive for two reasons: (1) A prominent outcrop, recognized as an extension of the Tennessee vein, persisted over a distance of 2,000 feet across the claims; (2) its proximity to the known ore shoots in the Tennessee-Schuylkill mine, one of the largest zinc-load producers in Arizona.Actual drilling was started September 18 and was terminated December 8, 1943. Eight holes, aggregating 2,979.5 feet, were drilled with two machines. ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resource to the end that they make the greatest possible contribution to national security and economy. I is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R.G. Knickerbocker, chief, analyses samples and performs beneficiation tests."

Jan 1, 1947

By Frederick K. Allgaier

This report presents the final data from a 5-yr Bureau of Mines study designed to determine the surface subsidence characteristics resulting from longwall coal mining in a geologic environment common to the Western United States, It includes a description of the geologic setting of the study site, the mine plan, measurement techniques, and results of the monitoring program. Measured subsidence values were obtained over four adjacent longwall panels- Major subsidence characteristics such as longitudinal and transverse profiles, angles of draw, time-related subsidence development, and critical width are discussed. The maxima subsidence value of 5.8 ft was 68 pct of the mining thickness. The average angle of draw was 30°, Subsidence at the center of the first panel continued for 46 months following undermining. The lengths of the longwall panels precluded a definitive determination of the critical width and maximum possible subsidence.

Jan 1, 1988

By Sabri Ergun

NEW theoretical data are presented for the intensity of X-rays diffracted from randomly oriented aromatic and alicyclic molecules and diamondlike structures such as are found in coals, cokes, and carbonaceous materials. Data have been computed using the Debye interference function. Computations for the smaller molecules have been made with the Univac 1204 computer: those for large structures, with either the IBM 704 or Bendix G-20 computer. A brief theoretical introduction of the Dobye interference function is given, and an outline is made of the treatment of experimental data so that the experimental interference function can be obtained.

Jan 1, 1965

By Everard Leland

This paper, describing the mining practices at the Pilares mine, Pilares de Nacozari, Sonora, Mexico, is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts. At present (1930) practically all the mineral production from the Nacozari district is from the Pilares mine of the Moctezuma Copper Co., a subsidiary of the Phelps Dodge Corporation. The ore is mined for its copper but contains associated silver in small quantities.

Jan 1, 1930

By L. C. IlsLey

Cooperation between the United States Bureau of Mines and the Safety in Mines Research Board of Great Britain, continuous, since 1924, s made possible this and other papers on safety subjects. Grateful acknowledgment is made to representatives of the board for their assistance in arranging visits to several mine-safety stations, and to F. R. Wynne, Deputy Chief Inspector of Mines, for arranging visits to mines in Great Britain and certain other countries in Europe. During the summer of 1927 the writer had the privilege of visiting the mine-safety testing stations An Great Britain, Belgium, Germany, and France, in the order named. All of these countries have large coal mines, many of which are rated as gassy. Therefore, a the installation of electrical equipment is contemplated each of these countries is confronted with the same safety problem as is the United States that is, the development of electrical equipment that will not, ignite gassy atmospheres should they through neglect or accident surround the equipment. The means employed by these countries in safeguarding gassy mines should therefore be of general interest to safety engineers of American coal mines, and a brief survey is given for each of the four countries mentioned. The fourth or last of these surveys covers conditions in France.

Jan 1, 1929

By D. C. Dahlin

The Bureau of Mines has investigated podiform chromite deposits in three ultramafic bodies in the Caribou Mountain and lower Kanuti River areas of central Alaska. The investigation, reported in two parts, was done as part of the Bureau's mission to help insure an adequate supply of minerals to meet the Nation's needs. Part I describes an extensive field investigation and mineralogical studies by personnel from the Bureau's Alaska Field Operations Center. This report, part II, describes the mineralogy of 11 samples that were high-graded from surface exposures at 10 sites and presents the results of laboratory batch beneficiation tests designed to concentrate the chromite. The 11 samples, peridotites and chromitites that consisted of variable amounts of chromite or chromium-bearing spinets, olivine, and serpentine, were beneficiated by grinding and sizing, gravity concentration, and electrodynamic separation. Three high-chromium chromite concentrates, two high-iron chromite concentrates, and one high-aluminum chromite concentrate were produced. Three other concentrates were marginal, and two were submarginal. Chromium recoveries ranged from 54 to 92 pct. These results indicate that the areas may be significant chromium resources. Potential platinum association with the chromite was also investigated. Analysis of these 11 samples indicates that the areas are not good platinum resources.

Jan 1, 1983

By David W. Tongue

This report describes the engineering work leading to the design of an underground coal mine piping system to transport approximately 2,000,000 cubic feet per day of methane gas to the surface from degasification holes drilled horizontally into the coalbed in existing coal mines. Safety instrumentation for detection of gas leaks and provisions for automatic emergency shutdown are included in the design. It also includes specifications for a safe system of handling gas, water, and drill cuttings during drilling of the horizontal holes and recommendations for compressor and metering facilities at the surface. The main pipeline is recommended to be constructed of polyethylene plastic pipe joined by a butt fusion method while lateral lines and separator and meter piping at the horizontal holes are recommended to be screwed steel piping. The materials used are to be resistant to the forces of impact exerted by falling rock. The pipelines are to be suspended from the ceiling with pipe hangers. All steel components are protected from chemical corrosion by applying protective coatings and the vertical casing to the surface is protected from electrolytic corrosion by a rectifier station. Methane gas detectors monitor the mine atmosphere to detect the presence of gas leaks and a pneumatic plastic tubing line provides for control of the safety shutdown system. Both the recommended design and the required construction procedures are in compliance with the applicable Federal codes for coal mine safety.

Jan 1, 2012

By Joseph A. Hrabik

The Bureau of Mines compared the feasibility of mining deep phosphate deposits by a borehole mining system with mining by proven conventional techniques. An economic comparison of the borehole mining system with conventional dragline and bucket wheel excavator mining systems was completed at various mining depths and production rates. Hypothetical phosphate deposits, with various overburden thicknesses and reserve tonnages, were defined. Geologic conditions necessary for the application of the borehole system were identified. Discounted cash flow analyses based on derived capital and operating costs were used to generate rates of return and product prices. Borehole mining was found to be more economical where overburden thickness was 150 ft or greater; however, at 50- and 100-ft thicknesses, conventional surface mining was more economical. Overburden thickness has a great effect on the economic feasiblity of the conventional mining systems but less effect on the economics of borehole mining. Economies of scale are only realized in conventional mining, since larger equipment is employed to achieve greater production, whereas increased production from borehole mining is achieved using additional equipment units. A comparison of the environmental effects of borehole and conventional surface mining systems showed that borehole mining is environmentally more desirable.

Jan 1, 1983