Search Documents

By Jeanne A. Smith, Suzanne D. Smith

Annoyance, fatigue, and musculoskeletal pain have been reported during prolonged exposures to propulsion-generated vibration in military propeller aircraft1. The objective of this study was to determine the vibration mitigation properties of selected seat cushions and the effects of occupant seating posture during exposure to higher frequency multi-axis vibration associated with military propeller aircraft. Methods A Navy E-2C Hawkeye crew seat was mounted onto the Six Degree-of-Freedom Motion Simulator (SIXMODE). Six seat pan cushion configurations were tested during exposure to an E-2C vibration signal collected in the field1. Seat pan cushions 1 – 5 were used with the original E-2C seat back cushion. Cushion configuration 6 included seat pan cushion 5 with a prototype seat back cushion. Triaxial accelerometer pads were mounted onto the seat pan and seat back cushions to measure the vibration entering the human. Data were collected for seven subjects seated upright with their backs in contact with the seat (back-on) and not in contact with the seat (back-off). Spectral analysis techniques were used to analyze data at the two dominant frequencies associated with the propulsion system (propeller rotation frequency (PRF) ~18.5 Hz, and blade passage frequency (BPF) ~73.5 Hz). Overall accelerations were also calculated between 1 and 80 Hz. Vibration Total Values (VTVs) were calculated using the weighted seat pan and seat back (back-on only) accelerations and compared to the comfort reactions given in ISO 2631-1: 19972. Results In general, the highest accelerations observed at the seat pan occurred in the fore-and-aft (X) direction at both the PRF and the BPF for all cushions and both postures. The most pronounced effect was at the BPF in the X direction, where all configurations showed significantly lower seat pan accelerations than configuration 1 (original E-2C cushion) with the back-on posture. Configuration 5 was the exception with the back-off posture (Fig. 1A, Repeated Measures ANOVA, P<0.05). The most pronounced effect of posture occurred at the PRF in the X direction, where all cushion configurations showed significantly lower seat pan accelerations with the back-off posture (Fig. 1B). All configurations except configuration 2 showed similar VTVs as compared to Configuration 1 (Fig. 2, P<0.05). Configuration 2 tended to show the lowest weighted acceleration levels. The overall VTVs (back-on only, Fig. 2B) showed significantly higher accelerations as compared to both the back-on and back-off seat pan point VTVs (Figs. 2A &

Jan 6, 2006

By E. P. Ferrero

Analyses of 38 crude oil samples from 25 fields in Algeria, Libya, and Nigeria are presented in this report. The 38 crude oils are listed alphabetically by country and field. Also shown are the geographic and geologic sources of the samples analyzed, the companies that supplied the samples, the general characteristics and analytical and computed data, and the production for the fields from which the samples were obtained.

Jan 1, 1966

By E. P. Ferrero

Analyses of 38 crude oil samples from 25 fields in Algeria, Libya, and Nigeria are presented in this report. The 38 crude oils are listed alphabetically by country and field. Also shown are the geographic and geologic sources of the samples analyzed, the companies that supplied the samples, the general characteristics and analytical and computed data, and the production for the fields from which the samples were obtained.

Jan 1, 1966

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing clay mining, crushing and grinding methods, and costs, at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The, cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in many instances cause embarrassment to the individual operator as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulation shall ensue. The following report deals specifically with the methods employed by the Evans Pipe Co., Uhrichsville, Tuscarawas County, Ohio. The author wishes to acknowledge the assistance of the following company officials: T. J. Evans, II, president; T. J. Evans III, vice president and general manager; and L. P. Young, general superintendent.

Jan 1, 1936

By Peter N. Gabby

In 1992, the Bureau of Mines conducted a mineral resource investigation of the 27,034-hectare Steel Mountain/Yuba River study area and the 16,544-hectare Breadwinner study area. There were approximately 535 lode and placer claims in or partially in the Steel Mountain/Yuba River study area, and 84 lode and placer claims in or partially in the Breadwinner study area. In the Atlanta and Rocky Bar mining districts, both adjacent to and in the Steel Mountain/Yuba River study area, 30,232.4 kg (972,000 02) of gold and 62,838.3 kg (2,020,000 02) of silver had been produced. Most of this production came from outside the study area. Placer properties adjacent to (and a few in) the Breadwinner study area had production of 93.1 kg (2,992 oz) of gold and 20.0 kg (642 02) of silver. Twelve properties in the Steel Mountain/Yuba River study area have potential for resources; eleven have alteration and/or mineralization similar to that found at Atlanta with potential for gold, silver, and tungsten resources, and one has alteration and mineralization associated with polymetallic vein type deposits with potential for gold, silver, copper, lead, zinc, and tungsten resources. Adjacent to the study area, large bars of gold-bearing gravel can be found along the Middle Fork Boise River. Four properties in the Breadwinner study area have potential for mineral resources; one has alteration and mineralization associated with skarn, polymetallic vein, and, possibly, copper-molybdenum and molybdenum porphyry types of deposits; two have alteration and metal assays associated with polymetallic vein, and possibly copper-molybdenum and molybdenum porphyry types of deposits; and one has alteration and mineralization similar to that found at Atlanta. These four have potential for gold, silver, copper, lead, zinc, molybdenum, and tungsten resources Adjacent to and extending into the Breadwinner study area are large bars of gold-bearing gravel along North and Middle Forks Boise River.

Jan 1, 1993

By Claud Johnson, Kristine M. Krajnak

Vibration transmitted to the upper limb by the chronic use of hand tools can result in cold-induced vasospasms finger blanching and cyanosis, similar to that seen with Raynaud’s phenomenon (4). These vasospasms, commonly referred to as vibration white finger (VWF), are in part the result of an increased sensitivity of peripheral arteries to the vasoconstricting effects of norepinephrine (e.g., (1-3)). However, alterations in vasodilating factors could also contribute to vasospasms. The goal of these studies was to determine if exposure to a single bout of vibration alters concentrations of the vasodilator, nitric oxide (NO), in a rat tail model of vibration. To determine if vibration exposure alters NO, we exposed animals to a single bout of vibration and measured concentrations of the synthetic enzymes, nitric oxide synthetase (NOS)-1 and NOS-3 in the ventral tail artery. We also directly assessed arterial concentrations of NO using a nitrate/nitrite assay. Methods General apparatus. Animals were placed in Broome-style restrainers, and their tail was secured to a vibrating or stable platform. Rats were exposed to a single 4 h bout of tail vibration (125 Hz, acceleration of 49 m/sec2 r.m.s.) or restraint control. Animals were euthanized with an overdose of pentobarbital (100 mg/kg) and the ventral tail artery was dissected and frozen. Experiment 1: Male Sprague Dawley rats (6 weeks old, n = 32) were used for all exposures. All animals were maintained in AAALAC accredited facilities, and all procedures were approved by the NIOSH Animal Care and Use Committee, and were in compliance with the CDC Regulations for the Care and Use of Laboratory Animals. Animals were euthanized 1 or 24 h after the completion of the exposure. Western analyses were performed on total proteins (80 µg/lane) isolated from the C16-18 artery segments. Band densities were detected by chemiluminescence and quantified using Scion Image, and analyzed using 2-way ANOVAs. Experiment 2. Nitrate/nitrite concentrations.. Male Sprague Dawley rats (n = 24, 6 weeks of age) were maintained and exposed as described above. All animals were euthanized 24 h after the exposure and the ventral artery was collected. Nitrate/nitrite concentrations were measured in ventral artery tissue homogenates using the nitrate/nitrite colormetric Assay Kit (Caymen). Results Analyses of band densities revealed that there was an effect of time (F(1, 17) = 6.03, p < 0.03) on NOS-1 protein in arteries exposed to vibration, with NOS levels being lower in arteries collected 24 h after the exposure than arteries collected 1 h after the exposure. Although NOS-1 proteins concentrations were slightly lower in control arteries collected 24 h after an exposure than arteries collected 1 h after exposure, post-hoc contrasts indicated they were not significantly different than 1 h controls. In contrast, NOS-1 band densities from arteries collected 24 h after the exposure were lower than those collected 1 h after the exposure (p < 0.01; Figure 1). NOS-3

Jan 6, 2006

By D. J. Parker

On Thursday, March 18, 1937, the country was shocked by news of a terrific explosion at the New London, Tex., school, which caused the death of 280 pupils rind 14 teachers. The explosion occurred at about 3:05 p.m. in the largest of the 11 school buildings on the campus. Figure 1 shows this building, market; "Main high school building?, with respect to other buildings, pipe lines, oil wells, and gas lines on the property.

Jan 1, 1937

By D. J. Parker

On Thursday, March 18, 1937, the country was shocked by news of a terrific explosion at the New London, Tex., school, which caused the death of 280 pupils avid 14 teachers. The explosion occurred at about 3:05 p.m. in the largest of the 11 school buildings on the campus. Fire 1 shows this building, marked "Main high school building", with respect to other buildings, pipe lines, oil wells, and gas lines or the property.

Jan 1, 1937

In 1987 Wyoming became the largest coal producing state in the country. The state is known for its extensive coal resources and extremely thick coal seams. Wyoming&apos;s coal reserves total about 69.3 billion tons, or 14.2 percent of the U.S. coal reserve. Coal seams range generally from 10 to 80 feet in thickness, although one seam is 220 feet thick. The coal-bearing areas of Wyoming underlie approximately 41 percent of the state&apos;s total land area. Wyoming&apos;s coal ranges from lignite to high volatile bituminous. Most of the coal produced is subbituminous from the Powder River coal region near Gillette. The presence of coal in Wyoming was discovered before 1834 on the Belle Fourche River. The state&apos;s first mine opened in Carbon County in 1865, and with the completion of the trans- continental railroad, the demand for coal increased. Currently approximately 80 percent of Wyoming&apos;s coal production is shipped out-of-state to meet the growing demand for low- sulfur coal to fuel electric generating plants. Wyoming received conditional regulatory approval November 26, 1980. Its Abandoned Mine Land Program was approved February 14, 1983.

Jan 1, 1992

By E. Owens, R. Gudavalli, D. Wilder, T. Xia

As mechanical shock and vibration environments evolve, it is important to understand their potential effect on human operators. Human beings are sophisticated mechanisms comprised not only of passive components with mass, damping, and stiffness characteristics, but also of components that can actively affect apparent mass, stiffness, and damping. Because the lumbar spine can exhibit local, short-column buckling, stability of the human trunk depends on the responsiveness of the neuromuscular control system.1-2 We have been evaluating the ability of patients with back pain to respond to a series of sudden loads. We believe the results have implications for isolation design and standards development. Methods 153 patients, aged 21 to 55, presenting with back pain agreed to enroll in a research study that randomly assigned them to one of three treatment arms: high velocity low amplitude spinal manipulation, low velocity variable amplitude spinal manipulation, or wait for 2 weeks and then be randomized to one of the above groups. Response to sudden load testing was one of a battery of baseline evaluations performed upon entry into the study and prior to treatment. EMG electrodes were attached to the skin over the paraspinal muscles of the standing participant bilaterally 3 cm from midline at the L3 level. While standing upright on a force plate (Bertec), participants were fitted with a strap around their back and hooked to a load cell in front of their chest. An accelerometer was rigidly attached to the load cell. Impact was applied to the chest using a cord attached to a falling weight. The weight’s fall distance was varied between 9 and 13 inches to account for the size of the subject. The subject was blindfolded and wore headphones playing white noise to prevent cueing of when the weight was dropped to apply the load. Hence, although the participant knew a load was about to be applied, he or she did not know the instant it would occur. Just before the weight was dropped, a 4 second data collection process was started for the two EMG electrodes, load cell, accelerometer, and force plate. The load drop was repeated 6 times, at irregular intervals, over a period of 2 minutes. The raw data thus collected was reduced to obtain several values: 1) length of time from the pull on the harness to the beginning of the response of the left and right paraspinal muscles (LES, RES), 2) time and magnitude of the maximum response, 3) force and acceleration experienced at the chest, and 4) the time and magnitude of the center of pressure location (COP). A general linear model was used to evaluate the results. Results For the EMG data, of the 1,824 observations made, 90% of them indicated a response. Prior to the sudden load, resting muscle activity was different between left and right sides (p=0.0001) and between males and females (p=0.0001). Female subjects began to respond to the sudden load within 92 to 110 ms and males from 101 to 109 ms. Females exhibited more variation in starting

Jan 6, 2006

By Paul J. Guay

This report presents the results of evaluating a longwall mining system specifically designed to extract a very deep web (60 inches or deeper) from a longwall panel. The report includes a productivity and cost analysis comparing the new mining sys-tem with a high capacity conventional longwall operation taking a 30-inch wide web. The analysis shows the new system will increase annual production 44 percent and decrease cost per ton off the face 21 percent. The report also includes conceptual drawings and specifications for a high capacity four-drum shearer and a unique shield type of roof support specifically designed for very wide web operation. The advantages and problems associated with wide web mining are discussed in general and as they relate specifically to the equipment selected for the new mining system. The study concludes by recommending that surface coal loading tests be conducted as the follow-on work.

Jan 1, 1978

By Martin D. Conyac

A mineral resource survey of rock types and geologic structures indicates that the Mt. Henry RARE II area has low potential for the discovery of metallic minerals. Potential for coal and geothermal resources is negligible. Essentially, the Mt. Henry RARE II area has had no claim-staking activity, nor has any mine been developed in it. SETTING Size and Location The 23,000-acre (9,308 ha) "1t. Henry RARE II area (No. 1-666) lies within the Kootenai National Forest approximately 36 mi (58 km) north of Libby, Montana, in the Purcell Mountain; of Lincoln County. Irregularly shaped, the area measures roughly 5-1/2 mi (8.9 km) north-south by 8 mi (12.9 km) Past-west, and lies about 1-1/2 mi (7.2 km) south of the Canadian border.

Jan 1, 1982

By D. W. Butner

This Information Circular , one of a series published by the Bureau of Mines , reports on the methods and costs of mining and concentrating zinclead ore at the Highland Surprise mine in the Pine Creek area of the Coeur d'Alene region of Idaho . The mine is owned and operated by the Highland Surprise Consolidated Mining Co. , which supervises operations of the Nevada Stewart group of claims , which is adjacent on the northwest . These properties are at the extreme eastern end of a zone of fracturing that strikes northwest across the Pine Creek area . In fractures along this zone are the principal Pine Creek mines ; these are the Highland Surprise , Nevada Stewart , Sidney , Denver , V and Idaho , Liberal King , and Northern Light . Country rock at the Highland Surprise is argillite of the Prichard formation (Belt series ) . Fracturing has permitted the movement of mineral- izing agents that have replaced adjacent walls and crushed country rock with sulfides . Ore minerals are sphalerite and galena with accessory pyrite , chalcopyrite , pyrrhotite , and siderite . Three principal ore shoots were found on the Highland Surprise property . The Highland ore shoot was mined from outcrop to the 400 level . The Surprise ore body has been developed to a depth of 1,400 feet on the dip of the vein . The outcrop of the Surprise ore shoot was 150 feet long and 2 to 4 feet thick ; on the 1,150 ( lowest ) level , the ore shoot is 320 feet long and 10 to 17 feet thick , with good zinc content . Surprise ore shoot No. 2 occurs 250 feet west of No. 1 and has been mined from the 500 to the 1,000 level . From 353,000 tons of ore mined between 1910 and 1948 , the property has a recorded production of 256,000 ounces of silver , 7,500 tons of lead , 24,000 tons of zinc , and 412 tons of copper . Both shrinkage and cut and fill stoping methods are used at the Highland Surprise , but shrinkage is unsuitable for mining below the 700 level , because faulting has weakened the walls . Development of the Surprise ore , as well as exploration laterally and along the strike , is prosecuted steadily . A prospect heading is being pushed westward toward Nevada Stewart ground from the 700 level . The mill has a rated capacity of 275 tons per day and operates near capacity . Selective flotation makes zinc concentrate that is shipped to the Anaconda smelter and lead concentrate that is trucked to the Bunker Hill smelter at Kellogg .

Mar 1, 1950

By Ralph P. Carter

It is apparent that coal will play an increasingly important role in satisfying the nation&apos;s energy requirements for the remainder of this century. Both deep mining and surface mining will be practiced to develop known U.S. coal reserves, but until significant improvements in the productivity of deep mining emerge, surface mining is likely to be predominant. This report addresses the problems of coal extraction and surface mine reclamation in the 11-state Midwestern coal resource region, where surface stripping of high-sulfur, bituminous coal has been a well-developed industry for most of this century. Midwestern coal markets have declined in recent years. In part this is a result of widespread conversions to more convenient and (apparently) economical liquid and gaseous fuels, but the decline in Midwestern coal use is also attributable to the impact of current air pollution control regulations that prohibit emissions of sulfur oxides and particulate matter. A part of the regional demand for Midwestern coal has been transferred to the Northern Great Plains where extensive low-sulfur coal reserves are currently being developed.

Jan 1, 1974

By S. S. Peng

Successful longwall mining requires a good roof control. A good roof control implies that: (1) no excessive pressure is build up in the face powered supports, and (2) chain pillars are designed in such a way that panel entries are well protected and interactions between adjacent panels are minimized. A clear understanding of strata behavior around longwall panels due to face movement is, therefore, the foremost requirement for achieving better roof control. This dissertation is designed to analyze the effects of strata behavior on longwall panels due to the mining activities. The following topics are studied: (1) the weighting, phenomena and their effects on front abutments, and (2) the chain pillar stability and pillar design under various roof conditions. Three dimensional finite element analysis was employed. The effect of parameters such as overburden depth, mechanical properties of the immediate roof and main roof, panel width, and size of chain pillar on (t) and (2) were analyzed. Four typical models were utilized to simulate various phases of panel extraction under various combinations of the above parameters; model one is to simulate the beginning of panel mining; model two is to simulate the situation that longwall face has passed more than half of panel length; model three is to simulate the completion of panel production; and model four is to simulate the second panel mining. The following formulae have been developed by applying multiple regression model to analyze the finite clement results: (1) a formula that classifies the type of root strata at the face area. (2) formulae that predict the first weighting and periodic weighting lengths. (3) a formula for design of the chain pillar size. Case studies were performed to check the validity of the formulae proposed. Comparison of the formulae proposed for the chain pillar design with other formulae were also performed.

Jan 1, 1984

By J. W. Jensen

EXTENSIVE research and development was performed on the manganese-copper vibration-damping alloys to determine the relationship between the properties of the alloys and variations in composition, fabrication, Mid heat treatment. Mn-Cu alloys with unusually high specific damping capacity, 20 to 25 percent at a stress of 5,000 psi, have also the following useful properties: Tensile strength, 90,000 to 110,000 psi; yield strong, 60,000 to psi; elongation, 20 to 25 percent; hardness, 90 Rockwell B; and fatigue limit at, 28,000 to 30,000 psi. Both standard and special methods of testing were employed to obtain data on strength, modulus, hardness, resistivity, dilatation, micro-structure, crystal lattice, and damping capacity. The extensive tabular and graphical data on these properties are presented for alloys containing 50 to 85 percent as quenched d solution) and after various aging treatments. Expansion coefficients for all Mn-Cu solid solutions are graphed and a dilatometer study of contraction during aging is reported. Although high damping capacity is associated with aging to precipitate a-Mn from solid solution, with a cubic-tetragonal transformation and with the occurrence of antiferromagnetic ordering in Mn-Cu alloys, a tenable theory of the damping mechanism has not been reached.

Jan 1, 1965

The production and processing of crude petroleum and natural gas are the dominant economic sectors of the Middle East, providing more than 80 % of the region&apos;s foreign exchange. In 1992, the 15 countries that constituted the region accounted for 29.5 % of world crude petroleum output, 20 % of world natural gas plant liquid production, and 5 % of world dry natural gas production. Only Cyprus and Lebanon were not crude petroleum producers. A fairly wide range of non fuel minerals is also produced in the region. The most significant are boron minerals, bromine, chromite, gypsum, phosphate rock, potash, strontium, and sulfur. However, the variety of minerals produced, output levels, and the size of the overall non fuel mineral economy of the region is dominated by Iran and Turkey. Turkey, with a diverse mineral production and strategically situated between Europe and the Middle East, was first in world production of run-of-mine boron minerals, second in strontium behind Mexico, and fourth in pumice. It was also a significant world producer of chromite, magnesi&apos;lm compounds, mercury, and sodium sulfate. Turkey was also the Middle East&apos;s largest cement and steel producer. Iran continued to expand output of most mineral commodities following the war with Iraq from 1980 to 1988. It was a significant world producer of gypsum and strontium and on its way to becoming a major iron and steel producer in the region. Despite a very small domestic mineral industry, Israel was second in world production of bromine and a significant producer of phosphate rock and potash. In terms of processed minerals, Israel was a major world diamond cutting center and exporter of cut diamond. Jordan ranked sixth in world production of phosphate rock. Saudi Arabia was eighth in world production of sulfur.

Jan 1, 1994

By H. H. Schrenk

[There is a need for method of determining: benzene vapor in air which is simple and accurate and suitable for making industrial hygiene surveys. The most widely used method in this country is the modification of the Elliott and Dalton6/ procedure. This depends on the nitration of the benzene to reduction to phenylenediamine with all excesses of standard titanous chloride; solution, and titration with e standard ferric ammonium sulphite solution. This method has the disadvantages of being what time consulting: and cumbersome it requires considerable apparatus, and a special modification is necessary in the presence of toluene.]

Jan 1, 1935

By Laurence G. Trudell

A geologic framework for interpreting stratigraphic and geographic variations of the Green River Formation in the Piceance Creek Basin is developed from lithologic data accumulated by the Bureau of Mines from oil-shale coreholes. From detailed Bureau of Mines descriptions of samples from nine coreholes and supplementary lithologic data from seven additional sampled sections, three cross sections were constructed along lines transecting the basin. Plotted as lithologic columns with corresponding oil yields and resistivity logs, the sampled sections are correlated on a time-stratigraphic basis. Distribution and correlation of nahcolite and halite zones are shown, and the approximate base of leaching of these saline minerals is indicated. General lithologic characteristics of members and zones are discussed and interpreted. Large-scale lithologic logs illustrate the nine Bureau of Mines core descriptions, and the complete description of Bureau of Mines-Atomic Energy Commission Colorado Corehole No. 1 is included in an appendix. The time-correlated cross sections provide a necessary framework for understanding the depositional history of the Green River Formation and will facilitate evaluation of oil shale and other mineral resources in the Piceance Creek Basin.

Jan 1, 1970

By H. H. Schrenk

There is a need for a method of determining benzene vapor in air which is simple and accurate and suitable for making industrial hygiene surveys. The most widely used method in this country is the Smyth modification of the Elliott and Dalton procedure. This depends on the nitration of the benzene to m-dinitrobenzene, reduction to phenylenediamine with an excess of standard titanous chloride solution, and back titration with a standard ferric ammonium sulphate solution. This method has the disadvantages of being somewhat time-consuming and cumbersome; it requires considerable apparatus, and a special modification is necessary in the presence of toluene. Recently Cook and Ficklen have published a method based on the oxidation of benzene with hydrogen peroxide in the presence of iron salts. This method requires the use of solid carbon dioxide to freeze out the benzene. The reaction Which produces the color is complex; and only approximate quantitative estimations can be made, except in a very narrow range.

Jan 1, 1935