Search Documents

By Victor R. Spironello

The Bureau of Mines has studied slags associated with ferrous melting, to evaluate substitutes for the auxiliary flux mineral, fluorspar. A waste material recovered from alumina reduction cells, "used potlining," was tested in an 18-in-ID basic-lined cupola and in a 1/4-ton, pilot-scale, basic oxygen furnace (BOF). One potlining fraction, No. 1 cut, is a carbonaceous (graphitic) material and represents the bulk of the entire cell lining. The other fraction, No. 2 cut, is a refractory backup. These materials contain significant quantities of fluorine and other elements fn various compounds. The potlining fractions were blended in ratios believed representative of available materials. Both lump and pelletized forms provided extremely fluid slag. No adverse effects were found on furnace performance, chemistry or strength of the metals produced, or the environment. Fluorine recovery in the slag and fluorine losses to the scrubber water and solids were about the same as when fluorspar was used. There was apparently no lining loss from the cupola, but there was lining attack in the BOF. Since the fluidizing ability of potlining is due in part to sodium and other elements such as aluminum and silicon, less fluorine is needed in the slags when potlining is used.

Jan 1, 1983

By George J. Conroy

This Bureau of Mines report summarizes the results of a study of mine inspection records covering 2,200 mining installations over a 3-year period ending December 1974. Tables show the relative frequency of violations of certain provisions of the Coal Mine Health and Safety Act of 1969 in particular areas of concern, such as circuit breakers, grounding, and permissibility. Examples of past use of the data and analyses are presented.

Jan 1, 1976

By Clinton C. Knox

To demonstrate the feasibility of unwatering ore reserves previously indicated in the virgin Melrose zinc-lead field in Kansas and Oklahoma, the Bureau of Mines .carried through a pumping project on the Park Walton farm in 1943. Due to success of the undertaking, attention was turned to exploration of other indicated ore deposits and promising areas within that part of the field benefited by .the drainage project, By the middle of 1946, four private mining companies were active in the field; and a considerable output of lead and zinc concentrate had been obtained from the new Park Walton mine and mill. The Park Walton Ore deposit was unwatered by installing deep-well pumps in three holes previously drilled by the lessee. Pumping was continued by the Bureau of Mines at a rate of 2,500 to 1,000 g.p.m. for about 6 months; during this time the local static artesian water-level, originally averaging 108 feet below the surface in the old drill holes was lowered to the 316-foot level, which justified beginning the initial shaft sinking and mine developments. In all, about 750,000,000 gallons of water was pumped by the Bureau of Mines at an operating cost averaging $0.024 per 1,000 gallons.

Jan 1, 1948

By Gary A. Halvorson

Plots were established on regraded abandoned mine spoil to determine if nearby good quality spoil could be used in place of topsoil for the reclamation of these sites. Gypsum, calcium chloride, and power plant ash were also tested to determine the effectiveness of these materials in reclaiming these sites. Two sites were selected on which very little vegetation was growing on highly sodic spoil material. Gypsum, calcium chloride, and ash were added to the spoil at a rate designed to reduce the (sodium adsorption ratio) SAR in the surface 15 cm to 10 or less. The good quality spoil (replacement soil) was then laid on the swface at rates of 0, 5 or 15 cm of material. The plots were seeded to a mixture of smooth bromegrass (Bromus enennis Leyss.), crested wheatgrass (Agropyron desertorum (Fisch. Ex Link) Schult.) and alfalfa (Medicago sativa L.). The addition of 5 or 15 cm of replacement spoil significantly improved vegetative growth on these sites. Chemical treatments had no effect on vegetative growth. Weathered ash showed no adverse effects on plant growth or soil properties.

Jan 1, 1991

By Martin H. Stanczyk

Bench scale, laboratory batch attrition grinding tests were made of a coarse commercial kaolin in a stainless steel, 5-inch-diameter attrition grinding machine to study the effect of a number of basic operating variables on particle size reduction and electric energy consumption. The results of the investigation showed that the more important operating variables influencing the efficiency of kaolin comminution and energy consumption requirements were type, size, and shape of grinding media, grinding media to clay weight ratio, peripheral rotor speed, clay slip pulp density, degree of pulp dispersion, and the angular arrangement of the rotor and stator bars. The tests also indicated that variables having less influence on grinding efficiency and energy consumption were pulp temperature, design of rotor cage, rotor clearance, rotor-stator bar interval, addition agents, pulp level, degree of pulp aeration, and chamber liners. The research showed that grinding media had the greatest influence on abrasion of machine parts and that spherical-shaped grinding media were superior to sharp angular or long bladed media with respect to media degradation, machine abrasion as well as grinding efficiency.

Jan 1, 1968

By E. R. Bauer

This report describes a U.S. Bureau of Mines investigation into the removal of gate road chain pillars in conjunction with longwall retreat mining. The research objective was to determine, through evaluations of the loads imposed on the gate road pillars and supplemental support elements in the entries, how the pillars, supplemental support, and entries were affected by the longwall abutment pressure. To achieve this goal, vibrating wire stressmeters and hydraulic flatjack pressure cells were installed in the support elements to monitor stress change caused by abutment pressure as a function of longwall face advance. The findings documented in this report are the result of information collected from instrumentation and observation at the mine. Pillar and support loading measurements and stability observations revealed that the roof and the sup- port elements remained stable during panel retreat, while the face progressed at a normal rate of advance. The ability to safely and efficiently mine chain pillars during panel retreat increases resource recovery and can provide several other benefits described in this report.

Jan 1, 1993

By Robert L. Lagace

This report describes the results of a system study of the factors influencing mine rescue attempts based on the use of electromagnetic VF rescue transmitters by trapped miners and helicopterborne search receivers by mine rescue personnel. The findings cover four main task areas. The first - mine emergency/disaster considerations - concentrates on characterizing the events and key parameters of mine fires and explosions related to trapped miner location and rescue activities. The parameters include critical time periods, affected areas, survival times, response and rescue times, and survival rates. The second - hardware considerations - concentrates on characterizing the relevant properties of VF rescue transmitters, oxygen-type self-rescuers, VF search receivers, helicopter performance, and signal detectability and sensor sweepwidths for helicopterborne sensors. The third - search theory probabilistic model develops a method to identify the most important regions to be searched, and to allocate helicopter-based search effort so as to maximize the number of miners detected in time to be rescued. The fourth - sensitivity analyses and application of the search model - exercises the search model on representative mine emergency/disaster scenarios to assess the impact and effectiveness of helicopter-based searches. Conclusions and recommendations are presented, together with a set of search scenario planning guidelines.

Jan 1, 1982

By Richard L. Fowler

An automatic steering control system was designed, installed and tested on a coal mine shuttle car. The system utilizes sensors and associated signal processing electronics developed under a previous phase of this contract. The automatic steering system performs the routine guidance functions of turning corners and straight-through tramming. The shuttle car driver retains full authority of speed, braking, load and unload functions and at any time may exercise his option with manual override or steering. Steering information is generated from signals derived from the existing Lateral Guidance sensor subsystem, and all operational features of the previously developed open-loop system are retained. Above ground system tests were conducted in a simulated mine constructed of wood panel ribs. Results were in good agreement with prior hybrid computer simulations undertaken to validate the basic control system over a broad range of conditions and to select system parameter values. The automatic steering system was successfully demonstrated in the above ground simulated mine to USBM technical representatives. Designed to meet USBM permissibility requirements, the system is ready for a Phase II underground testing program. Testing in actual underground mine environment is expected to provide additional data regarding recommended performance improvements and implementation techniques.

Jan 1, 1975

By Rupert O. Yantz

This report, authorized under contract Number H0111403 Amendment Number One, entitled, "Exploration of Illumination Concepts for Underground Coal Mines", contains the results of an investigation of methods, procedures, and technology for providing working place lighting in underground coal mines and construction of a prototype, man portable, mine illumination system and a prototype, machine mounted, mine illumination system for use in high and low coal entries of underground coal mines.

Jan 1, 1972

By Robert C. Steckley

A study of joints in Marathon County, Wis., was made to determine the orientation of regional paleotectonic stresses and to develop a method of using optical diffraction analysis (ODA) in studying joint orientations and spacings. Standard geologic and petrofabric techniques employing the use of a geologic compass and a Schmidt net were used in gathering, describing, and reducing joint orientation data. Analysis of selected outcrops with ODA indicates that ODA can be applied to study both joint orientations and spacings. ODA is shown to be a rapid method that can be used to complement standard petrofabric techniques, especially in the study of joint spacings.

Jan 1, 1972

By Annie G. Smelley

As a part of research conducted in its mission to effect pollution abatement, the Bureau of Mines, U.S. Department of the Interior, is developing a dewatering technique that allows for disposal of clay wastes, for reuse of water now lost with clays, and for reclamation of mined land. The technique utilizes a high-molecular-weight nonionic polyethylene oxide polymer (PEO) that has the ability to flocculate and dewater materials containing clay wastes. In laboratory experiments, coal-clay waste, potash-clay brine slurry, phosphatic clay waste, uranium tailings, and talc tailings were successfully consolidated. Coal-clay was te was consolidated from 3-. 6 to 57 percent; potash-clay brine slurry was consolidated from 3.8 to 35 percent; phosphatic clay waste from 15.6 to 49 percent; uranium tailings from 15.4 to 67 percent; tailings from talc production from 9.7 to 53 percent; and an acidic Ti02 slurr slurry from 1.68 to 30 percent.

Jan 1, 1980

By Kenneth H. Johnston

The Weber pool in Washington County, Okla. (fig. 1), covers an area extending from 2 miles east and slightly north of Bartlesville, Okla., to a point approximately 2-1P tiles northeast of Dewey, Okla. The pool is a part of the area designated by the Standing Committee on Oil Field Nomenclature, Kansas-Oklahoma Division, Mid-Continent Oil & Gas Association, as the Bartlesville-Dewey field. In the following discussion of the geology, development, and exploitation of the Weber pool, the writers, by means of structure maps, cross sections through various parts of the reservoir, and tabulated development data and production statistics, have recorded salient information on a field that was developed before .1910 in an Area that has been repressured since 1926. The total oil production to January 1, 19.0., from the 2,639 developed acres considered in this report, was approximately 14 million barrels, or a recovery of about 5,3;2 barrels per acre, or 227 barrels per acre-foot. The production of the estimated 18 million barrels of recoverable oil remaining in the Bartlesville sand reservoir will require the initiation of additional secondary-recovery practices on some of the leases and the application of a more systematic repressuring program on others.

Jan 1, 1950

By Horst Peter Wölfel

The goal of biodynamic models is to simulate the vibration behaviour of the human body. In combination with experimental studies biodynamical models can be a powerful tool for the analysis of the effects of vibration exposure on health [1] and comfort. This paper gives an overview of the state of the art of biodynamic whole-body vibration models of humans, addressing both numerical models and hardware dummies. Method Two approaches are distinguished, the phenomenological and the anatomical, as illustrated in Figure 1. [ ] Phenomenological models aim to reproduce the vibration behaviour of humans with respect to particular physical quantities, chiefly the driving-point impedance at the interface to the seat, and partly with respect to other transfer functions. Discrete systems of masses, springs, and dampers with several degrees of freedom whose topology and parameters are determined by structure- and parameter identification methods are used in the sense that the functions derived from measurements are reproduced as well as possible. This paper provides an evaluation of this methodology and defines its range of application as well as its limits.

Jan 6, 2006

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1986 was $405.2 million, a slight decrease from that of 1985. Alabama was second in the Nation in production of bauxite, crushed marble, and ferroalloys; third b fire clay; fifth in masonry cement and lime; sixth in total clays; and seventh in recovered sulfur. Alabama ranked 19th nationally in value of nonfuel minerals produced. Cement, clays, lime, sand and gravel, and stone were the major commodities produced.

Jan 1, 1988

By Roger L. Baer

Marine disposal of mill tailings has been practiced worldwide for over a century. However, only recently have the environmental effects of marine disposal been systematically studied. Some early attempts at marine disposal of tailings resulted in adverse impacts to marine life. However, recent advances in tailings disposal methods have included the introduction of engineered submarine tailings discharge systems, advanced environmental assessment and monitoring methods, and oceanographic modeling systems. Successful submarine tailings disposal (STD) has occurred at several mines. The U.S. Bureau of Mines (BOM) has undertaken studies of the disposal of mining and milling wastes in the marine environment. The BOM Alaska Field Operations Center, Juneau, initiated a review of the technology, regulations, and economic aspects of STD. The review illuminated the need for organization of literature on the subject, therefore the Bureau compiled this extensive bibliography on marine disposal of mill tailings. The bibliography presented here contains 1483 references and is also available through diskette in the Word Perfects format. A review of the references indicates that literature on submarine disposal inadequately covers the subject. The majority of the references listed only peripherally relate to the subject. Published literature on the engineering and environmental aspects of STD is severely limited.

Jan 1, 2011

By J. R. McVey

A 10-channel automatic data acquisition system has been designed and environmentally packaged for use with underground strain-gage applications and associated instruments. The system uses commercially available components and is assembled in two plastic enclosures. Environmental control is provided through a specially designed (compressed-air) air-conditioning system and water-resistant cabling. Accuracies of 0.01 pct and resolution of 1 µV have been obtained in underground tests.

Jan 1, 1973

By John P. Borovsky

A 3-year study was conducted to evaluate the problems and benefits of using vegetation to stabilize tailing from a potential Minnesota copper-nickel milling operation. The project consisted of three separate investigations: a waste characterization study, a greenhouse study and a field study. With few exceptions, the physical and chemical characteristics of the tai ling were found to lie within the range of properties of Minnesota soils. The tailing lacks organic matter; is deficient in nitrogen, phosphorus and potassium; and may contain elevated levels of soluble salts and heavy metals, particularly copper and nickel. Numerous grasses, forbs and woody plants will tolerate the tailing as a rooting medium. Peat incorporation and topsoil dressing provided few benefits to the revegetation process which were not provided by a fertilizer application. With fertilization, grass/legume production in the tailing was comparable to local agricultural yields. Concentration of heavy metals in grasses grown in the tailing were generally below suggested tolerance limits for plants and animal forage. Legumes tended to accumulate higher concentrations of copper and nickel, and metal uptake of most plants was positively correlated with rate of fertilization. Tailing drainage water contained elevated levels of heavy metals, and establishment of vegetation had little effect on the quantity and quality of tailing drainage water. However, topsoil dressing significantly increased drainage water volume when compared to unvegetated control plots. Copper-nickel tailing revegetation recommendations were developed.

Jan 1, 1983

By R. F. Chaiken

The Bureau of Mines has carried out experimental and theoretical studies with prilled and pulverized ammonium nitrate-fuel oil (AN-FO) mixtures containing varying amounts of fuel oil in an attempt to quantify the effects of stoichiometric composition, nonideal detonation behavior, and expansion volume on the production of CO, NO, and N02 fumes. Experimental fume measurements were obtained in the Bureau's large closed gallery facility (7.2 X 104 liter expansion chamber) and in the standard Crawshaw-Jones apparatus (90--liter expansion shamber) using a prepackaged charge configuration containing about 450 g of explosive.4 The theoretical calculation of toxic fumes was achieved with an equilibrium detonation code called "TIGER,," Contrary to initial expectations, the NOx (= NO + N02) fumes from the large gallery test were found to be in essential agreement with the Crawshaw-Jones results. It was also concluded that (1) "TIGER" calculations offer a good approach to the prediction of toxic fumes; (2) there is a basic problem in extrapolating laboratory measurements of CO fumes to mine conditions--this being due to postdetonation oxidation of CO to CO2; and (3) the detonation velocity decay rate of an explosive is a useful experimental parameter for correlating toxic fumes production with nonideal detonation behavior.

Jan 1, 1974

By J. J. Forbes

Since 1910 the Bureau of Mines has given training in the care and use of oxygen breathing apparatus under conditions that may exist during mine fires and after mine explosions. In 1929 the Bureau supplemented this instruction by initiating a course in advanced mine rescue training to prepare mine officials and others to organize men for mine rescue and recovery operations. The course of instruction has been developed and expanded since its inception to keep abreast with new ideas, methods, and equipment. Four miners' circulars were issued to be used in the training course. The first of this series (Miners' Circular 33) deals with mine gases and the various methods of detecting them; the second (Miners' Circular 34) gives instructions for sampling and analyzing mine atmospheres; the third (this circular) describes methods and equipment for protection against mine gases; and the fourth (Miners' Circular 36) explains procedures in sealing and unsealing mine fires and in conducting recovery operations, These circulars have been revised from time to time to keep them up to date.

Jan 1, 1954

By C. W. Owings

One phase of Bureau of Mines health and safety work is promotion of the use of safe and effective dust-collecting devices in connection with rock drilling in coal mines. To insure that adequate equipment of this type is available to the coal-mining industry, the Bureau of Mines conducts investigations and issues approvals for dust-collecting equipment that meets the requirements of a schedule established for testing dust collectors intended for use in connection with roof drilling for roof bolting and for other rock drilling. 6/ Performance tests are conducted under the provisions of this schedule by engineers of the Branch of Health Research. This circular describes briefly the requirements and procedure for approval and lists drill-dust collectors that have been granted approval as of January 31, 1956. The addresses of manufacturers of approved devices are listed alphabetically at the end of this circular.

Jan 1, 1956