Search Documents

The Tenth International Conference of Directors of Safety in Mines Research was held in the United States from September 28 through October 2, 1959, at Hotel Webster Hall, Pittsburgh, Pa. The Conference was organized by the Federal Bureau of Mines. In accord with the program outlined at the Ninth Conference (1956, Heerlen, Holland), the papers submitted dealt with the following three subjects: 1. Safety of coal mine explosives 2. Explosion hazards in mines 3. Ignition and fires in mines Seventy papers were presented. There were eight technical sessions followed by an extended tour of the Bruceton facility of the Bureau of Mines on October 2. Simultaneous translation was provided in the three official languages of the Conference--English, French, and German.

Jan 1, 1962

By R. W. Watson

A belt-wearable self-contained self-rescuer (SCSR) manufactured by the CSE Corp. and designated the "SR-1OO" was evaluated for safety in the underground mine environment by the U.S. Bureau of Mines. The evaluation consisted of laboratory tests on the chemicals contained in the unit and field trials to simulate the mine environment. This report summarizes the test results and compares the results with those from earlier tests with chemical and compressed oxygen self-rescuers. It was concluded that the new SCSR did not pose any different or more severe hazards than the earlier units. In view of the mine-proven safety record of the SCSR's now in service, no reason could be found to disallow use of the belt-wearable unit.

Jan 1, 1991

By Rimas Pakalnis, Doug Milne, Marc Ruest, Lewis Martin

Whereas many researchers and mine engineers have conducted tests on cable bolts using various grouts, water: cement ratios, and physical modifications of the cable to determine the load-carrying characteristics ofa bolt, few studies have been conducted on cable bolts fitted with internal instruments. Those studies that have been done have concentrated on cable response averaged over significant (6.1 m) cable lengths. Researchers at the Spokane Research Laboratory (SRL) of the National Institute for Occupational Safety and Health in Spokane, WA, are investigating the physical properties of cable bolts by replacing the conventional king wire with a modified king wire on which strain gauges have been installed. A numerical analysis was performed to match laboratory results. Loads calculated by the model were then compared to loads measured in the laboratory on 1.83-m-long cables grouted into two 0.91-m-long pull-tube assemblies. Load along the cable was monitored with 20 strain gauges installed along the length of the cable. This paper documents test results on these modified cable bolts. The instrumented cable bolt provided reproducible point measurements of cable load as opposed to load measurements averaged over long cable lengths. Such point measurements can assist in interpreting the influence of cable confinement, grout quality, rock mass stiffness, and other factors. The instrumented cable bolt is a practical field and research tool because it can predict point loading along the cable. The instrument has been successfully field tested at FMC's Granger Mine, Granger, WY; the Meikle Mine, Carlin, NV; the Stillwater Mine, Nye, MT; and the Getchell Mine, Golconda, NV. By monitoring load and displacement of the rock mass using these instrumented bolts, more-effective ground support can be selected and installed, which will lead to safer working conditions for miners.

Jan 4, 2004

By Mark I. Copeland

The Bureau of Mines investigated the effect of up to 1 wt-pct of copper and silicon on the heat treatment response and hardness, tensile, and impact properties of hot-rolled medium-carbon steels. The steels were prepared by induction melting and fabricated into plates by forging and rolling. The tensile strength of 0.2-wt-pct carbon steels containing 0.3 wt-pct silicon was affected significantly by copper in both the hot-rolled and heat-treated (600° C) conditions, whereas the tensile strength of the 0.3-wt-pct carbon steels was less affected. A 600° C treatment was considered optimum as a post-rolling treatment to strengthen the steels by copper precipitation. Strengthening of 0.2-wt-pct carbon steels by silicon was reduced by increasing copper contents.. Optimum impact strengths occurred at about 0.3 wt-pct silicon in 0.2-wt-pct carbon steels containing 0.6 and 0.8 wt-pct copper. The impact strengths were lowest for 0.2-wt-pct carbon steels containing over 0.8 wt-pct copper and greater than 0.3 wt-pct silicon, especially in the heat-treated condition. Copper and silicon solutes and copper precipitates strengthened the steels. This effect was augmented slightly by strengthening through grain refinement by these solutes.

Jan 1, 1973

By F. Sillers, R. T. C. Rasmussen

"INTRODUCTION This is the fourth report of investigations dealing with the cooperative tests between the Bureau of Mines and industry on the use of electrolytic manganese in steelmaking. The first report dealt with the use of electrolytic manganese in the manufacture of stainless steel 3/ the second with its use in acid electric steel practice, 4/ and the third with its use in low-carbon basic open-hearth steelmaking. 2/ A résumé of those investigations E7 appeared in the magazine STEEL. 5/ The present report deals with the use of electrolytic manganese in the manufacture of four types of stainless steel and the new Timken 16-25-6 alloy. The Bureau of Mines supplied The Timken Roller Bearing Co. with 62,000 pounds of electrolytic manganese for use in the tests.The electrolytic manganese was produced at the Bureau of Mines pilot plant, Boulder City, Nev., by the process developed by the Bureau and described in Bulletin 463, Operation of Electrolytic Manganese Pilot Plant, Boulder City, Nev., by J. H. Jacobs. J. W. Hunter, W. H. Yarroll, P. E. Churchward, R. G. Knickerbocker, R. W. Lewis, H.A. Heller, and J. H. Linck. The workcarried out under the direction of R. S. Dean, formerly assistant director, Bureau of Mines, and R. G. Knickerbocker, formerly chief, metallurgical branch, as part of a long-range program involving the development, manufacture, and use of manganese from domestic ores. Preliminary arrangements for the plant tests were made by the late A. A. Dow. 7/"

Jun 1, 1947

By E. J. Gleim

A list of permissible mine equipment, tested and approved by the Bureau of Mines previous to January 1, 1942, was published in Bureau of Mines Information Circular 7207.3/ The list of that date was complete as to equipment then available and in current use. Information Circular 7240,4/ published as a supplement thereto, listed equipment approved curing the calendar year 1943. The present list is another supplement covering approvals issued during the calendar year 1943. The items are numbered to indicate the consecutive order in which each type of machine or device was approved in its particular classification. Thus, Information Circular 7207 gave 19 drills and drilling machines on the Bureau's active list. No additional approvals were given in 1942, but the three issued in 1943 bring the total to 22. Item 102, under Loading Machines and Conveyors, also appeared in Information Circular 7207, and items 120 and 124 appeared in Information Circular 7240. These numbers are repeated here to show that approvals were granted during 1943 for additional voltages on machines previously listed for one voltage only. Equipment listed in these circulars is approved by the Bureau of Mines only when found upon inspection and test to comply with minimum standards of safety as outlined in schedules prepared on the basis of many years of experience in dealing with safety problems of the coal-mining industry. The use of such equipment in mines known to be gassy, as well as in those that may become so, is earnestly recommended in the interests of safety. This circular is published so that the industry may be kept

Jan 1, 1944

By Paul S. Goodman

Volume I This report presents the first national survey of miners' attitudes and opinions about their-work. The goal is to present attitudinal data that bears on coal production. Interviews were conducted in 26 mines with 2,000 miners. High levels of cooperation were exhibited by management, union and the employees. Data are presented about miners' attitudes about general aspects of their work such as pay, supervision, their jobs, etc. Another section of this report reviews opinions about specific aspects of work performance. Recommendations are presented.

Jan 1, 1985

By David A. Hill

This volume contains a summary of the results of past analyses on U.S. Bureau of Mines Contract No. 80122061 which are relevant to electromagnetic location in mine rescue situations. The analytical results indicated that detection of a trapped miner equipped with a special transmitter is feasible in most situations. Location of the miner by surface measurements is also generally feasible within certain errors. The feasibility of miner detection and the accuracy of miner location have been examined theoretically for a wide variety of situations. Agreement with experimental results is generally good in cases where measurements are available. Personnel involved in the investigation include J.R. Wait (Principal Investigator), D.A. Hill (Co-Principal Investigator), K.P. Spies, A.Q. Howard, and Lana Slusher (Administrative Assistant).

Jan 1, 1974

By R. R. Lowery

This project was proposed to provide information on the hazards associated with arc melting of thorium. A general air-sampling analysis was made to determine the separation, concentration, and distribution of thorium daughter (decay) products throughout arc melting, machining, and forging processes of a thorium handling facility. The value of well coordinated health physics program is stressed in connection with potential health hazards and personnel protection. Building, equipment, and exhaust ventilation requirements for such a facility are discussed. Special handling methods are described for thorium. INTRODUCTION The Bureau of Mines at the Albany Metallurgy Research Center has been involved in handling the naturally radioactive metals, uranium and thorium, for several years. Cooperative work for the Atomic Energy Commission has been carried out with thorium metal, and as a result the concerned laboratories of the Center have accumulated experience on the hazards associated with this metal. This report details the radioactive hazards arising from the arc melting, machining, and forging of thorium.

Jan 1, 1962

By H. W. Wainwright

.1. The purification pilot plant and the equipment, solution, and gas cycle used for removing hydrogen sulfide and carbon dioxide are described. 2. As sulfur recovery is necessary in any large Fischer-Tropsch plant, pilot-plant runs were made at 300 p.s.i.g. to study the efficiency of tri-ethanolamine solutions in removing selectively hydrogen sulfide from gases containing varying amounts of carbon dioxide. 3. Aqueous solutions of TEA of 20, 30; 35, and 50 percent were investi¬gated. Data indicate that 30 to 35 percent is the optimum concentration if both selectivity and economy are considered. Slightly better selectivity is obtained with the.20 percent solution, but steam consumption is greater owing to the higher solution rates. Results from our pilot plant runs indicate that a 50 percent solution not only produces an acid gas of lower hydrogen sulfide content but also requires high solution rates to effect hydrogen sulfide purification. 4. Data from 37 runs using TEA are presented in tabular form. In addition, the data are correlated and presented in three sets of curves. By using these curves, it is possible to calculate the compositions of the purified and acid gases for various raw gas mixtures. 5. In cooperation with the Southern Natural Gas Co., investigations were carried out at 300 p.s.i.g. on the simultaneous removal of hydrogen sulfide and carbon dioxide, from gases using various concentrations of diethanolamine. 6. Data from 17 runs employing 20, 30, and 40 percent DEA are reported in both tabular and graphic form. 7. A comparison of the data from one DEA run made at 200 p.s.i.g. with those from the runs operating at 30O p.s.i.g. shows float the absorption capacity of the solution, and, hence, the steam requirements per gallon are about the sage for both pressures. .The only real advantage of the higher pressure is the additional volume of gas that can be treated. 8. The quantity of steam needed to reactivate fouled TEA and DEA solutions increased as the reactivator pressure was increased about 1,0 to 1.1 pounds of steam was required for each gallon of circulating solution when the reactivator was operated at 5 p.s.i.g. 9. A curve is included that shows the effect of the hydrogen sulfide con-centration in a lean 35 percent TEA solution on the hydrogen sulfide content of the purified gas and on steam consumption for reactivation. 10. Both TEA and DEA reduced the organic sulfur content of the raw synthesis gas considerably. Analyses of the lean amine solutions showed a gradual build up of sulfur compounds, indicating that the compounds formed by the amines and organic sulfur do not break down under the ordinary operating conditions of the reactivator. 11. Considerable operating difficulty was encountered in the pilot plant owing to foaming of the amine solutions. Laboratory experiments in which the effectiveness of certain antifoam agents was studied showed Alkaterge C to be most promising for the particular conditions studied.

Jan 1, 1952

By Frank B. Fulkerson

Of the about 60 million pounds of aluminum used in the Pacific Northwest in 1960, 40 million pounds or two-thirds was used by 10 companies. One of these companies made airplanes and missiles; one manufactured roofing, siding, and tubing; three produced truck tractors, truck bodies, or truck trailers; two made architectural metal products; one made irrigation and industrial products; one was a general foundry; and one was a shipyard. These companies contributed to regional growth by developing markets outside the area; some have worldwide sales. Aluminum consumption increased at an average rate of 7 percent annually from 1954 to 1960. Airplane manufacture, formerly preeminent in aluminum use, no longer was in first place in 1960. By industrial group, the leading users were manufacturers of building products, 30 percent; airplanes and missiles, 22 percent; truck tractors, truck bodies, and truck trailers; 17 percent; general foundries, 5 percent; ships and boats, 4 percent; mobile homes, 4 percent; other transportation equipment, 3 percent; and irrigation equipment and all other products, 15 percent.

Jan 1, 1962

By J. L. Konchesky

In gasifying pulverized coal with steam and oxygen, the particle size of the coal fed to a gasifier should be as small as economically possible. A potential way to achieve this advantage is to reduce the particle size of the coal by passing the coal-steam mixture at high velocity through a heated tube coil before the mixture enters the gasifier. To evaluate this method the Federal Bureau of Mines flashed coal-water slurries in externally heated metallic tube coils to determine the extent of size reduction. The first of two different laboratory-scale apparatus reduced the average particle diameter of subbituminous C coal from 190 to 110 microns at an outlet velocity of 330 feet per second (f.p.s.). At the same outlet velocity, a second apparatus reduced the average particle diameter from 250 to 140 microns. An increase in velocity produced more finely divided coal, but variation in temperature and pressure had no effect except as they affected velocity. Virtually the same size reduction was noted for five ranks of coal at equal velocities. The rate of increase in particle-size reduction with increase in velocity decreased with a decrease in particle size. The pulverizing mechanism was concluded to be abrasion of the particles with each other and with the tube wall.

Jan 1, 1961

By S. H. Ash

THE ANTHRACITE region of Pennsylvania contains over nine-tenths of the total anthracite deposits of North America and produces all but an insignificant proportion of the total output of anthracite in the Nation. The whole economy of the northeastern section of the United States depends, to a large extent, on the mining of Pennsylvania anthracite, which is shipped to New Jersey, New York, and New England and is a principal source of energy and heat for that entire region. The responsibility of the Federal Government for developing an engineering method that will prevent inundation of the Pennsylvania anthracite mines and keep them in operation has long been recognized. To obtain a reliable picture of the anthracite-mine-water problem and to solve that problem, it is necessary to have factual data on the volume and the quality and character of the mine water handled by the pumping plants in the anthracite region, as well as the kinds of pumps utilized and problems concerning their operation.

Jan 1, 1953

By Maria I. De Rosa, Charles D. Litton

The National Institute for Occupational Safety and Health (NIOSH/PRL) conducted a series of large-scale experiments to evaluate the effectiveness of optical flame detectors, photoelectric smoke detectors, and combined ionization and photo­electric smoke detectors for rapidly detecting mining equipment cab fires. The detec­tor alarm times were then used to trigger the discharge of a fire inerting system inside the cab to suppress cab material fires. This paper discusses the types of fire detectors tested, the experiments that Were conducted, and the results that were obtained. Con-" elusions are that rapid detection of equipment cab fires can be achieved to trigger the discharge of a fire inerting system inside the cab to protect the operator in the cab.

INTRODUCTION The pager phones used in many underground coal mines are battery- operated, party-line telephones with provisions for loudspeaker paging. The system is two-wire, non-polarized, and is operated by self-contained batteries. Many of the individual units are certified as permissible. Requirements for installation are specified in state and federal regulations, such as in the Code of Federal Regulations, Title 30, Mineral Resources, Part 75. The major federal regulations that affect communication in coal mines are noted below, with a brief description of the subject matter in each of the relevant paragraphs. Refer to the cited paragraphs of Title 30 for explicit details of these regulations. (This brief description is for reference purposes only.) Minimum Requirements (paragraphs 75.1600, 75.17 13-2, and 75.1003-1) Approved telephone or two-way communication will be provided between the surface and each main shaft landing and each working section ; to the nearest medical assistance; and shall be protected from contact with trolley wires or trolley feeder wires. Installation Requirements (paragraphs 75.5 16-2, 75.52 1, and 77.508-1 ) Communication wires will be supported on insulated hangers, attached to messenger cables, or buried, to protect against mechanical damage ; installed opposite trolley wires; and insulated near power conductors . . . each cable will have lightning arresters within 100 feet of going below ground . . . and arresters will be provided wherever telephone wires enter a building. Wire and Cable Requirements (paragraphs 75.5 16-2, 75.5 17, and 75.52 1) Communication cable means two or more insulated conductors, covered by an additional abrasion-resistant covering; power wires and cables shall be adequately insulated and fully protected; and lightning arresters shall be connected to low-resistance grounds, more than 25 feet from neutral grounds.

Apr 1, 1975

By Dana C. Reinke

A job analysis is a written list of the tasks associated with doing a particular job. In drilling, describing the steps associated with adding rod to the drill steel would be an example of a task associated with the job. How to hammer casing or fish a lost drill bit out of a hole would also be job tasks. Develop a written list of job tasks. Ask drillers in your company if the tasks listed are correct and accurately reflect how to perform the job. While each driller may do the job a little differently, some tried?and?true methods are required to perform certain tasks safely and correctly. You may find a separate analysis is needed for different drilling jobs (e.g., a residential well or a monitoring well). Also remember to include the tasks of both the helper and the driller.

Jan 1, 2005

By R. E. Kennedy

"INTRODUCTION In a previous publication4 results were given of numerous experiments made on the in-flammability of gas mixtures consisting of methane, hydro a. carbon monoxide, nitrogen, and carbon dioxide. Data were obtained and tables prepared giving the inflammable limits of each of these combustibles when mixed with various proportions of carbon dioxide and nitrogen. By the use of these data and the application of Le Chatelier's law, it was found possible to calculate the limits of inflammability of any gas mixture containing any or all of the above gases.Various mixtures of the five gases given above were prepared and their limits determined experimentally and then calculated. Good agreement was found between the determined and calculated results when complex gases encountered in mine safety work were tested. Of special significance was the accurate calculation of the limits of inflammability of gases from mine fires, gases from mine explosions, detonation products of explosives, blast—furnace gases, automobile exhaust gas, and other gases of a similar character.Using the method given in the above report, Yeaw5 investigated a number of industrial gases including oven, coal, producer, blue, carbureted blue, and dry quencher gases, and found the determined and calculated results to agree remarkably well, thus giving further proof of the value of such a means of determining dangerous conditions when combustible gases are encountered in practice.GASES FROM A POTASH MINEGases were recently encountered in a potash nine in New Mexico, containing the com-bustibles, methane, hydrogen, and ethane. In one special case a mild explosion occurred when these gases were mixed with the right proportions of air and ignited it therefore became necessary to know the inflammability of these mixtures in order that the proper precautions could be taken to prevent explosions."

May 1, 1932

By H. L. Burmeister

This is one of a series of publications by the Bureau of Mines dealing with mining methods and costs at representative operations in the United States. The report describes all phases of the mining methods for the open-pit operation and milling practices employed at the Vermont Asbestos Mines in Lamoille and Orleans counties, Vermont. A brief history of discovery and development of these asbestos deposits is given, and the ore deposits are described. Methods employed in exploration, sampling, and estimation of tonnage and grade are outlined. A breakdown of available cost figures is summarized in the last section. All asbestos ore produced in this area has been won by the use of surface-mining methods. Two quarries, the Lowell and the "C" Area, are in operation. The quarries combined are producing and the mill is processing approximately 3,500 tons of ore per 3-shift day The average 40,000 tons of crysotile asbestos fiber produced at this plant annually accounted for 96 to 98 percent of the total fiber produced in the United States in 1958. The mine is located (fig. 1) approximately 4 miles north of Eden Mills village on the southeastern flank of Belvidere Mountain (fig. 2).

Jan 1, 1962

By James H. Aase

[This study provides data on the physical and hydrological makeup of the ,t hakes waterway system and forecasts quantities, traffic patterns, and ping cost of prospective bulk mineral commerce projected to be transported it. Factors affecting the shipping cost of iron ore, bituminous coal, imestone were quantified and integrated into a computer program that can d to estimate costs under varying sets of conditions. Combined ship of iron ore, bituminous coal, and limestone in 1995 were estimated at million tons. The cost of operating the U.S. vessel fleet for trans-ng an indicated 80 percent of this traffic tonnage was projected to be $163. 5 million.]

Jan 1, 1970

By D. K. Denton, J. M. Girard, D. F. Scott, T. J. Williams

Personnel from the Spokane Research Laboratory, National Institute for Occupational Safety and Health, examined an underground pillar at the Homestake Mine, Lead, SD. Investigations involved strain relief and seismic tomography studies in the mine, and ultrasonic velocity measurements on pillar core in the laboratory. Measured octahedral normal stress was 37 MPa (5,366 psi); seismic P-wave velocities averaged 5.2 km/s (17,060 ft/s); and ultrasonic velocities at a pressure of 39.6 MPa (5,750 psi) averaged 6.3 km/s (20,669 ft/s). The difference between in-mine and laboratory velocities is attributed to the attenuation of seismic energy by mine fractures larger and more numerous than those in the samples of core measured in the laboratory. Using these results, researchers hypothesize that pillar rocks have the ability to withstand stress an order of magnitude greater than they currently sustain.