Search Documents

"INTRODUCTION These inspection standards have been prepared for use as a guide for the Federal inspection of anthracite mines. They are a revision of ""Tentative Inspection Standards for Anthracite Mines,"" published as Bureau of Mines Information Circular 7231 in January 1943 and used as a guide for Federal inspections. Numerous changes in the original standards have been made, due in part to recognition of shortages of some types of safety equipment due to the war, in part to need of additional standards to cover certain mine conditions and practices, and in part to conditions not foreseen when the original standards were prepared.Throughout these standards reference is made to determining the methane content of the mine air by using a permissible flame safety lamp. The Bureau has approved various electrical devices for the detection of methane, but it is recognized that new devices for determining the percentage of combustible gases as well as the percentage of oxygen, might be perfected for general use in mines, and therefore it may be necessary to revise certain standards to include the use of such equipment if and when the device is accepted as being permissible.About one-fourth of these standards are marked with an asterisk (*) as being of particular importance in preventing accidents in many coal mines; however, failure to carry out the suggestions made in such of the other standards as are applicable may also lead to loss of life.With continuing change in mining methods, some of these standards may become inapplicable, and further revision will be advisable. Therefore, question regarding these standards and suggestions regarding new standards should be brought to the attention of the Bureau, so that changes may be made from time to time. Numerous changes proposed by mine operators and by State mining departments have been incorporated in these standards."

May 1, 1944

By M. Dattilo

The U.S. Bureau of Mines has been conducting research on the use of waste-derived zinc as a partial replacement for pure zinc in the electrogalvanizing process. The end product of this process is automotive sheet, which has enhanced cosmetic protection over previously used cold-rolled (CR) steel. In this study, primer-coated specimens of CR and electrogalvanized (EG) steel were subjected to the on-vehicle environment and monitored periodically by electrochemical impedance spectroscopy (EIS) during immersion in 1M NaCI solution. The results of these tests were compared with immersion-only conditions. Scanning electron microscope (SEM) and energy-dispersive X-ray (EDX) techniques were also used to evaluate the corrosion processes and compare them with atmospheric exposure specimens. EIS was found to measure the corrosion associated with on-vehicle exposure, thus providing an excellent screening technique for evaluation of the performance of EG automotive sheet steel.

Jan 1, 1990

By Robert Lee Stahl

Comprehensive field tests were made by the Federal Bureau of Hines at the Conda open pit mine near Soda Springs, Idaho, to determine whether surface geophysical techniques could be used to detect and delineate faults in phosphate deposits. The tests included seismic refraction, magnetometry, electrical resistivity, and airborne photography. Of the several geophysical techniques tested in the field, horizontal resistivity profiling was the most effective method for diagnosing faults. The method is quick, inexpensive, accurate, and can be easily used by mining company personnel to detect and delineate faults.

Jan 1, 1975

By Daniel G. Di Canio

Reference information and user instructions for Version 3.0 of the Accident Cost Indicator Model (ACIM) software package are presented. ACIM estimates the tangible costs of occupational injuries, illnesses, and fatalities in the United States mining industry.

Jan 1, 1983

By A. R. T. Denues

This investigation was made under a cooperative agreement between the United States Department of the Interior, Bureau of Mines, and the Pittsburgh Testing Laboratory. Funds were supplied by the Chile Exploration Co., whose executive offices are in New York City. The support, cooperation, and services of these agencies made the work possible and are acknowledged gratefully. The writer wishes to express his particular indebtedness to the staff of the Explosives Division of the Bureau of Mines for services and assistance, particularly Dr. Wilbert J. Huff, consulting explosives chemist, J. C. Holtz, J. E. Tiffany, and A. B. Coates; to F. O. Gardner, treasurer of the Pittsburgh Testing Laboratory; to G. B. Holderer, consulting engineer in connection with liquid-oxygen explosives for the Chile Exploration Co.; to the Enos Coal Mining Co. of Oakland City, Ind., particularly to G. H. Utterback of the staff of the mine for providing facilities that made field tests possible; and to full-time assistants J. W. Rothhaar and J. G. P. Weinheimer and to W. S. Hiller, part-time assistant, who were employed under the cooperative agreement.

Jan 1, 1940

By Edwin M. Thomasson

HELIUM SHIPMENTS in 1964 exceeded the volume shipped during the previous year for the 15th successive time. Shipments from Bureau of Mines helium plants were 667.4 million cubic feet,2 about 6 percent more than in 1963. Production at Bureau of Mines plants totaled 784.5 million cubic feet. An additional 3,193.1 million cubic feet, which was produced by private companies participating in the helium conservation program, was purchased by the Bureau and stored underground for future use. The Bureau of Mines continued to sell helium at $35 a thousand cubic feet, the price established in 1961. Substantial railway freight rate reductions for tank car shipments of helium went into effect during the year, resulting in a lower delivered price for helium. As the Nation moved ahead in the space age, it became increasingly apparent that helium would continue to play an essential role in research, in technology, in defense, and in industry.

Jan 1, 1965

By G. Huang, S. Vytla

Computational fluid dynamics (CFD) is a continually developing numerical technique by which complex fluid flow problems can be solved on computers. To be able to transfer CFD expertise to analyze and design a face-ventilation system, a comprehensive validation study of current CFD tools against mining-related benchmark experiments is required. In the last four years, such studies, funded by National In¬stitute for Occupational Safety and Health (NIOSH) under Grant #R01 CCR415822, were conducted in the Department of Mining Engineering at the University of Kentucky. A wide array of ventilation schemes and mining configurations were considered. Recently, an additional study was performed in cooperation with the NIOSH Pittsburgh Research Laboratory. This study was dedicated to the methane behavior in the empty (containing no equipment) face area with a blowing curtain and a 10. 7-m (35-ft) setback. In this paper, the authors present and discuss the computer-simulation data and compare them with data collected during the laboratory studies at the NIOSH lab.

By I. Liebman

The Bureau of Mines conducted experiments on coal dust explosion suppression. The investigation took place on a beltway in the double-entry of the Bureau's Experimental Mine. Using conditions that simulate those in a working mine, the investigation showed that a coal dust explosion can be readily initiated in a conveyor belt entry. Also, the explosion can spread into adjacent entries through opened crosscuts (stopping destroyed by explosion) to propagate for long distances even though the adjacent entries are rock dusted in compliance with regulations. Passive water barriers (water-filled tubs) were found to be effective in suppressing explosions on a beltway; however, barrier efficiency was reduced by opened crosscuts. The study indicated that the beltway barrier should be the distributed type consisting of continuous rows of water-filled tubs covering long distances along the entry. A plan is outlined for the installation of a water barrier system in a working coal mine for the protection of a beltway.

Jan 1, 1981

By Samuel P. Harteis

Many mining operations rely on retention bulkheads to provide a barrier between impounded water and active mine workings. However, bulkhead failures can cause catastrophic flooding that puts the underground workforce at risk. Underground observations and evaluations of existing bulkheads indicate that a systems approach is required when building an underground water or slurry retention system. In addition to engineering the bulkhead, the designer must ensure the quality control of materials and workmanship of the bulkhead, the reaction of the mine strata when exposed to water under pressure, and methods to monitor the performance of the retention system. Researchers from the National Institute for Occupational Safety and Health (NIOSH), with the assistance of the Mine Safety and Health Administration (MSHA), conducted an extensive review of bulkhead permits submitted to the MSHA Technical Support office in Bruceton, PA. In addition, the researchers visited accessible bulkhead installations at undeground mining operations to gather information related to construction practices, maintenance issues, and monitoring and emergency response procedures. Several key items were identified that must be considered when permitting the installation of an underground fluid retention system.

Jan 1, 2008

By Ronald Branstetter

Gaseous and particulate exhaust emissions from 20 diesel engines in service at five underground mines were measured with high accuracy instrumentation. The engines that were tested were checked for faults or maladjustments. The vehicle and engine maintenance organization was studied at each mine and an idealized maintenance program was devised. Faults were induced in a new diesel engine to determine their effect on the characteristics of the exhaust emissions. The results, conclusions and recommendations from this investigation are presented in this final report.

Jan 1, 1983

Relatively few longwall mines in the U.S. operate under multiple seam conditions where the two seams are less than 200 ft apart. This paper describes the experience of six that do. These operations are located in PA, WV and UT, and include examples of both undermining and overmining. Some operate above or beneath their own workings, others are in historic mining districts and must contend with abandoned mines that are decades old. The lessons that these mines have learned cover a broad range of topics, including: • Whether to stack gateroads or place them under old gob areas; • How to size pillars and select artificial support to cross longwall stop lines; • How to use yield pillars to minimize multiple seam stresses and coal bump potential, and; • When to anticipate the creation of pathways for gas, water, or oxygen between current and abandoned gobs.

By O. C. Blade

[In its general study of crude petroleum, tic Bureau of Mines has published several reports that include analyses of samples of crude petroleum from Oklahoma fields3/. This report discusses briefly the properties of crude oil samples collects in come of the producing fields in the State ACKNOWLEDGMENTS This investigation was conducted by the Bureau of Mines in cooperation with the State of Oklahoma. No study was made under the general supervision of R. A Cattell, chief engineer, petroleum and Natural-Gas Division, Bureau of Mines Washington, D. C., and N. A. C. Smith, supervising engineer, Experiment Station, Bureau of Mines, Bartlesville, Okla., and under the direct supervision of Ludwig Schmidt senior petroleum engineer Bureau of Mines, Bartlesville, Okla.]

Jan 1, 1939

By O. C. Blade

In its general study of crude petroleum, the Bureau of Mines has published several reports that include analyses of samples of crude petroleum from Oklahoma fields3/. This report discusses briefly the properties of crude oil samples collects in come of the major producing Yields in the State. ACKNOWLEDGMENTS This investigation was conducted by the Bureau of Mines in cooperation with the State of Oklahoma. The study was via e under the general supervision of R. A Cattell, chief engineer, petroleum and Natural-Gas Division, Bureau of Mines, Whishington, D. C., and N. A. C. Pith, supervising engineer, Petroleum Experiment Station, Bureau of Mines, Bartlesville, Okla., and. Under the direct supervision of Ludwig Schmidt, senior petroleum engineer, Bureau of Mines, Bartlesville, Okla.

Jan 1, 1939

By George L. Gates

[When clays are mixed with water to -.,tee mud fluids for use in trilling wells for nil and --ac b ;l-,e rotary method the liquid mixtures have certain physical characteristics that vary with the quantity and size of their inherent solid particles. All naturally occurring clays contain variable quantities of particles of different sizes ranging from relatively coarse (sands) through -,.tedium (silt) to fine materials of colloidal dimensions. Tie colloid content is extremely important 2.s a desirable _.'ale constituent of mud fl-z to fit well drilling. ';'it:-out colloids the souk?;,' in a mud fluid wouldr rapidly, end ti-c-and. wall-building qualitites of the' fl,-,id would l ..o r re 1 impaired. Mud .fluid.^ with insufficient quantities of colloids also are lacking in "lubricating" g listen, and it is, to ° min casing in, -)re holes drilled with such fluids.]

Jan 1, 1941

By B. W. Haynes

This Bureau of Mines report describes the laboratory processing of manganese nodules and the results of tailings characterization obtained during the cooperative program with the Department of Commerce's National Oceanic and Atmospheric Administration (NOAA) and the Bureau. Five technically feasible first-generation nodule processing methods were operated at bench scale to generate sufficient tailings and slags for physical and chemical analyses. A description is given for the laboratory operation of the individual unit operations of each process. The laboratory-generated tailings and slags were tested for physical properties, mineral content, elemental and ion content, and leachability for all five processes. The results of leachate testing using the Environmental Protection Agency extraction procedure (EP) toxicity test, the American Society for Testing and Materials shake extraction test, and the EPA-U.S. Army Corps of Engineers seawater elutriant test showed very low to negligible leaching of metals from the tailings and slags. Results of the EP toxicity test demonstrated that the wastes are nonhazardous as defined in the Resource Conservation and Recovery Act (Public Law 94-580).

Jan 1, 1985

By S. J. Rodgers

This report presents guidelines on methods of dust control in conventional coal mining operations. The normal mining cycle and equipment used in a room and pillar conventional section are described. Main ventilation, section ventilation and face ventilation are discussed in detail. Proper installation of line brattice, maintenance of proper air flows at the face and split ventilation are stressed. The effects of maintaining the end of the line brattice near the face are described. The advantages and disadvantages of blowing and exhausting face ventilation are presented. The use of water sprays on cutter bars and loading machines is described. The design of a nonclogging water spray system developed under a Bureau of Mines contract is presented. Other methods of reducing dust exposure are discussed and include alternative procedures for shot firing and administrative controls.

Jan 1, 1983

By Kenneth C. Ko

An engineering investigation was carried out on the technical and economic feasibility of implementing flexible liner/backpacking support systems In an advancing tailgate longwall mine. The system for a model mine consists of a circular tube constructed of liner plates and flyash backpacking. Flyash is pneumatically stowed into the tailgate. Small amounts of cement may be mixed to improve the support capability of the fill In difficult local ground conditions. Water is added inside the nozzle immediately prior to spraying. Results of theoretical analyses and a field test show that the designed system is technically feasible, can be cost-competitive, provides more stable ground conditions, and can Increase productivity and coal recovery, when compared with existing retreat longwall systems. In certain mine layouts, the new system can reduce the direct mining costs by a significant amount. The system would be particularly applicable to deeper coal beds with bad ground conditions.

Jan 1, 1980

By Gregory R. Wagner

The Program of Mine Safety and Health Research described in this document reflects the continuing commitment of the Spokane and Pittsburgh Research Laboratories to focus on the most important areas where research can make a difference in reducing risk and improving safety and health for miners. It is the first program of work conducted since Congress mandated closure of the former U. S. Bureau of Mines (USBM) in the Department of the Interior and supported integration of the health and safety research function of the former USBM into the National Institute for Occupational Safety and Health (NIOSH). Organizational changes made FY97 a challenging year of transition. Ongoing research was reviewed and revised to reflect the new, more limited, health and safety mandate of the research laboratories. The mining industry, mine worker representatives, and interested government agencies provided broad input to assure that the research performed would focus on the most critical safety and health problems confronting mining today and which are expected to be faced in the future. The two laboratories worked to evolve coordinated programs of safety and health research, each with a special focus. The work of the Spokane Research Laboratory is directed toward issues of special importance to the Western mining industry, particularly those safety hazards found in metal/nonmetal mining and surface mining. The work of the Pittsburgh Research Laboratory will continue to focus on Eastern mining, particularly underground coal mining. Traditional areas of expertise for understanding and preventing fires and explosions and for controlling the hazards of dust and noise will continue to reside in Pittsburgh. Each laboratory is developing new capabilities in the analysis of relevant safety and health information to assure that program priority-setting decisions are informed by the best available data. Recognizing the continuing importance of communicating the results of research to all who are capable of improving safety and health conditions in mining, each laboratory has developed an activity for information dissemination and coordination with stakeholders. In the midst of organizational self-examination and change, the research staff in Pittsburgh and Spokane have never wavered from their continuing commitment to conduct the highest quality scientific research-solution-oriented scientific work meant to reduce the risk of injury, disease, and death from occupational hazards in mining. The pages that follow give insight into some of the program activities and accomplishments from FY97. I hope you share my pride in the many accomplishments of the NIOSH mine safety and health research program during this year. This report comes at a time of increasing stability for the mine health and safety research program. The organizational changes in Spokane and Pittsburgh have been concluded, and NIOSH has succeeded in recruiting a new, permanent associate director for mining to lead this critically important national program. Congress has contributed to an optimistic future by providing expanded funding for NIOSH mining-related research for the next fiscal year. On a personal note, I greatly appreciate the opportunity I have had to serve as the NIOSH Acting Associate Director for Mining during this transitional year. The commitment and intelligence with which the mining research staff pursued their mission was matched by their patience and understanding in moving into a new organizational environment. All of us committed to improved safety and health for this Nation's miners owe them our respect and appreciation.

By Edward L. McHugh, Louis J. Denes, Jami M. Girard

A prototype portable hyperspectral imager that operates in the visible and near-infrared ranges of the electromagnetic spectrum was field tested at an open-pit mine. The tests were sponsored by the Spokane Research Laboratory, National Institute for Occupational Safety and Health, as part of an investigation of remote sensing technologies for use in detecting and monitoring conditions in surface mines that could lead to catastrophic slope failure. The spectro-polarimetric imager, built at the Carnegie Mellon Research Institute, employs an acousto-optical tunable filter (AOTF) to control wavelength, a phase retarder to measure polarization signatures, and a digital camera and computer to capture data. The spectral range of the instrument is 450 to 1000 nm at 10-nm intervals. High-resolution hyperspectral images of highwalls, outcrops, hand samples, and drill core were collected in the field. Spectra from the images closely matched those of specific minerals present and were used to classify the images. The field tests were designed to examine the feasibility of using spectral imaging to assist in compiling objective geologic maps of mine highwalls and other hazardous slopes. Results illustrate the capability of the method to discriminate materials within the image, validating the concept of simplified spectral imaging. A contributing factor in many slope failures is the presence and distribution of mechanically incompetent, clay-rich altered rock in slope faces. Spectral features of clays and other minerals are more distinctive in the short-wave and mid-infrared part of the spectrum; the capabilities of the instrument need to be extended into this range to apply the AOTF-based technology to common geologic materials. A field-portable hyperspectral imager could find broad application in remotely identifying diverse materials from solids and coatings to gases.

By P. S. Haury

"INTRODUCTION Many ore deposits were discovered in the Wallapai Mining District, which covers the Cerbat Range in Mohave County, Ariz., during the early period of mining there from about 1865 to the 1890's. A considerable amount of production was obtained from shallow lead carbonate ores that carried considerable gold and silver.Mining was revived in 1906 and again during the First World War, and soma of the mines were deepened into the underlying sulfide zone. Substantial quantities of metal were recovered from two mines, the Golconda and the Tennessee-Schuylkill, that were, developed to depths of 1,600 and 1,400 feet, respectively. The Golconda is credited with $6,500,000 gross productions. 2/ This mine was not operated after 1917. The Tennessee-Schuylkill is still operating after a yield of about 300,000 tons of ore that averaged 4.33 percent lead and 7.74 percent zinc and contained an appreciable amount of gold and silver.Many of the old mines were reopened in 1942 or 1943 under the stimulus of premium prices for lead and zinc. A large proportion of this work was finished with loans from the Reconstruction Finance Corporation. It was believed that a good deal of lead and zinc could be recovered from the mines if a custom mill for concentration of the ores was available locally."

Aug 1, 1947