Search Documents

By O E. Jr Crenwelge

Recently promulgated regulations governing blast induced ground vibrations in the mining industry contain a frequency criterion as one option for verifying compliance. This criterion is based upon an oversimplified method which assigns the entire peak particle velocity amplitude to one frequency. Depending upon the nature of the vibration time history, it is possible that this frequency may not even be one of the predominant frequencies of the signal. In addition, the criterion does not specifically define the data analysis approach to be used by the industry for obtaining either the amplitudes or the frequencies of the vibration components. And because personnel in this industry generally have little understanding of vibration phenomena, a number of different approaches are currently being used for satisfying the criterion. This paper presents a method for obtaining both the Fourier amplitude-frequency spectrum and the integrated predominant amplitude-frequency components for the vibration record. The method is both physically and mathematically correct and is in common use in a number of other industries. Therefore, it should be of help to regulators, blasters, and consultants charged with developing, enforcing, or implementing ground vibration criteria.

Jan 1, 1988

By Lon D. Santis

This paper presents data and theorem to calculate the risk of experiencing undesirable lightning related events while blasting or while engaged in other lightning sensitive activities. The paper provides an overview of lightning hazards in blasting operations and a brief history of lightning related blasting accidents. Lightning continues to be the primary cause of premature initiations of explosives in mining; on average, over two such incidents are reported to the Mine Safety and Health Administration (MSHA) each year. The energy contained in lightning discharges and how this energy sets off explosives in mining is presented. Three categories of lightning warning methods: public media, lightning detectors, and atmospheric electrostatic field measurement are discussed. The remainder of the paper presents recently acquired data on the spatial characteristics of lightning development. This data is used to estimate the risk assumed by blasters under certain conditions. Risk estimations are made for electric and nonelectric blasting if persons are evacuated when cloud-to-ground (c-g) lightning approaches within a certain distance. For example, about 0.6% of all c-g lightning strikes have no other c-g lightning strikes within 25 miles in the previous 30 minutes. The paper shows that a typical blaster using nonelectric initiation in a high lightning density area with a 100% accurate lightning detector set to alarm at 25 miles would have a lightning caused unplanned detonation every 14,000 years.

Jan 1, 1998

By Robert C. Fouchard, Gordon Chalmers, David E. G. Jones, Ivana Alilovic, Phillip D. Lightfoot

There have been numerous international instances over the last several years in which pumping emulsion explosives has resulted in accidents, apparently as a result of increased thermal sensitivity under these conditions. The key questions for the explosive industry are (1) what are the parameters that influence the sensitivity of emulsion explosives and, (2) how do these various parameters interact. To address the sensitivity of emulsion explosives to various parameters, a study was undertaken using an accelerating rate calorimeter (ARC) and a heat flux calorimeter (HFC). The effects ofthe addition of ammonium nitrate (AN) prills and different grades of aluminum (Al) on the thermal behaviour of emulsion explosives were determined. Additionally, changes in pressure, atmosphere (inert or oxidizing) and sample vessel material were assessed for their impact on thermal sensitivity. Addition of AN prills, fine granular Al or atomized Al did not affect the onset temperature for exothermic decomposition, so that the maximum “safe” temperatures for emulsions containing these additives will be similar. There were differences in the rates of self heating, however: AN prills decreased the rate of self heating, whereas atomized Al increased it. The emulsion formulations containing atomized Al produced small holes in titanium vessels. This phenomenon did not occur in Hastelloy C vessels, providing a reminder that materials of construction need to be carefully considered for equipment used to manufacture or handle emulsion explosives.. Both ARC and HFC experiments gave lower onset temperatures in air than in argon. We attribute this to oxidation of the oil phase by air. This result is significant for dry-running pumping conditions, where emulsion is heated in the presence of excess air.

Jan 1, 2000

By D G. Dressler, Paul Yeager

A previously little-known facet of seismic frequency spectrum analysis is gaining significance. The frequency spectrum of seismic waves promulgated from blasting is a significant factor in causing blasting complaints and threshold (architectural type) damages.

Jan 1, 1987

Blasting is a very cost effective method of rock fragmentation but its uncontrolled application often results in excessive damage to the perimeter of an excavation. Several perimeter control techniques are available but tracer blasting is commonly used in Canadian underground mines for overbreak control. This involves tracing a column of Ammonium Nitrate-Fuel Oil (ANFO) with a detonating cord. In order to investigate the techno-economic effectiveness of tracer blasting in perimeter control, a field experimentation was conducted which involved blasting in sublevel caving and sublevel sloping operations, experimental drifting, benching and pipe tests.

Jan 1, 1997

By H Y. Fang, H Sutherland, R M. Koerner

Due to the increased number of complaints by property owners to blasting related industries an apparent need for a clearer understanding of blasting-related damage is needed. We feel that direct structural crack monitoring during such blasts is the appropriate measurement technique. Instrumentation and interpretation of results for taking such measurements are described in this paper. Typical results from blasting and other environmental effects are also described which can eventually be related to Fracture Mechanics principles in the hope of clarifying such disputes in an equitable manner.

Jan 1, 1976

By Inc. The HDH Group

The Alternative Risk Market is defined as the segment of the insurance market that is made up of self insurance, risk purchasing groups, risk retention groups and captives. It is commonly referred to as the alternative to the traditional market, even though more the majority of companies today are insured through the alternative risk market than the traditional market.

Jan 1, 2007

By Minoru Kawamura, Koichi Kurokawa, Yukio Kato, Kenji Hashimoto

It is well known that ground vibration by blasting is mainly related to a distance and charge weight. However, it is not known the correlation between ground vibration and performances of explosives; for example, shock wave energy, bubble energy, detonation velocity and ballistic mortar value etc..

Jan 1, 1991

By Shih Wen Wang, Ronald R. Rollins

A blast casting model is proposed to predict the burden velocity in bench blasting. This blast casting model is the first theoretical model that 1) explains the throwing procedures and mechanisms, 2) uses the explosion pressure as the primary source in throwing rock fragments, 3) applies them to field conditions successfully. Also the predicted burden velocities are based on the rock properties, the explosive properties, and the drilling and initiation patterns. This blast casting model is programmed into a computer software "ROCKFRAG". The comparisons between "ROCKFRAG" predicted values and two field test data are in good agreement.

Jan 1, 1992

By Dirk van Zyl

Rock fabric information is often available from drill hole information and bench face mapping. An approach is presented to predict fragment size distribution of blasted material from this information as well as that obtained after the blast. The following information available from a mineral exploration drilling program was used in the prediction of fragment size distribution: largest piece, percent particles larger than 1 inch and RQD. Photographs of bench faces were used to estimate the fragment size distribution. Fracture spacings were evaluated along a series of parallel lines on the photograph. Photographic techniques were also used to obtain the grain size distribution of blasted material. m is paper describes the methodologies applied in some detail.

Jan 1, 1986

By Gordon F. Revey

In construction and mining work, situations occasionally occur where hard rock or concrete must be excavated at locations near critical structures or utilities. Fearing damage from blasting, contractors and engineers often explore the viability of using mechanical methods or expansive concrete to facilitate the excavation work. However, for moderate to large excavations, the prolonged duration and high cost of using these methods is often impractical. In these situations, under the right conditions, controlled blasting and blast-management methods can be used to speed up the work and lessen costs. The process of determining whether or not blasting is practical is often complex, particularly when risks are high.

Jan 1, 2002

By Bengt Ljung

Manual charging of long upward drilled holes in mines is a heavy and risky job today. Mechanization of this work has been requested for some time by miners, their supervisors, industrial safety organizations and the trade unions, all of whom are interested in improving the working environment. This paper presents newly-developed charging systems intended primarily for charging in connection with sublevel caving and sloping. These systems have been field-tested during 1977 in the LKAB mines in northern Sweden. The results of these field tests and the results of laboratory work conducted to help eliminate the risks involved in charging explosives are also discussed. The equipment being tested (see fig. 1 and 2) consists of a charging vehicle with articulated steering, the PT-60, which has been equipped with a hose feed system mounted on the hydraulic extension boom. From a sheltered position, the operator brings the detonator and primer to the hole opening, after which the hose is pushed in mechanically to the end of the hole. Measuring equipment indicates when and if the end of the blasthole is reached. The operator then withdraws the hose mechanically as charging takes place.

Jan 1, 1978

By Miguel Araos

The aim of this study was to understand clearly how VOD of emulsion-based gassed explosives is influenced by parameters such as nitrate salt composition in the oxidizing phase, product density, blend composition, gassing rate, type of sensitization, etc. Also some VOD testing was performed on watergel-based gassed explosives in order to compare the results with those obtained for emulsions. VOD measurements were conducted in the surface blasting facility at the Research and Development laboratory of ENAEX SA (Calama, Chile). Despite the fact that the influences of some parameters on VOD of emulsion-based gassed explosives are easily predicted, there was found to be an unexpected correlation. Although it is commonly believed that the VOD of gassed explosives depends on the density, this study found that the VOD depends on the both size and the amount of gas bubbles incorporated into the product as well as type of sensitisation, regardless of whether the explosive was straight emulsion or a blend. Density is just a consequence of the incorporation of voids into the explosive. Future work in this area may examine variation of other parameters, in order to obtain a greater knowledge of detonation properties and therefore to design more efficient explosives.

Jan 1, 2002

By Miie Shields, Ed Billington

Trail blasters for the National Park Service (NPS) live and work in remote mountain terrain throughout the western states, where any support or resupply may be sporadic and ditlicult and mountain weather affects every activity. Mechanical “aids” are the pick, shovel, rock-bar, wheelbarrow, and a Pionjar or Cobra dritl. The blaster is usually faced with an extraordinary range of work, t?om delay blasts in weathered rock using driiole depths of 18” (46cm) to as little as 4” (1 Ocm), through reducing boulders and talus fields to useable tread, blasting stumps, snags and log-jams, to the explosive disintegration and casting of animal czcasses. One day he/she might provide a 500cf (14 cu meter) anchor excavation for a suspension bridge, the next day directionally fall 60” (1.5m) diameter snags in a camp area, and the following day blast a 3-foot-wide (1 meter) tread bench across a steep bedrock slope. To be effective, the blaster must design each and every blast around desired end result, crew and public safety, maximizing effective use of limited quantities of explosive, and the minimnation of environmental effects. Since almost all drillhole blasting occurs in the weathered zone of the rock, blasting is more the art than the science of judging rock density, hardness, cohesion and prefracturing, and selecting explosives, drill and delay patterns, and loading techniques responsive to those conditions. For these reasons the NPS issues its own Blaster’s License, with a basic requirement of at least 40 hours of NPS blaster training and 3 years of supervised Blaster in-Training experience. The focus of this pre-license requirement is on safety and using explosives as a precision tool, versus just “blowing things up”.

Jan 1, 2002

By MSHA website

“Conditions at underground and surface coal mines can change dramatically during the winter months,” said Joseph A. Main, assistant secretary of labor for mine safety and health. “We must be ever mindful of the seasonal changes that can affect our work environments.”

Jan 1, 2011

By Zoltan Susanszky

Technical development in blasting requires improvement of industrial explosion techniques in two fields. One is to apply increasingly exact and economical solutions with more effective explosives, the other is to restrict as much as possible the environmental effect of explosions.

Jan 1, 1978

By E E. Cloete, R I. McCrindle

Permitted explosives were previously nitroglycerine based and cap sensitive. Due to safety, health and environmental requirements, water-containing explosives, such as watergels and emulsions, were used instead. However, in order for these explosives to perform at their designed level during blasting, a more powerful stimulus than is delivered by detonators on their own is required.

Jan 1, 1999

By J Lyall Workman, Peter N. Calder

Large hole rotary drilling is one of the most common methods of producing blastholes in open pit mining. Large hole drilling generally refers to diameters from 9 to 17 inch (229 to 432 mm), however a considerable amount of rotary drilling is done in diameters from 6½ to 9 inch (165 to 229 mm). These smaller diameters are especially prevalent in gold mining and quarrying.

Jan 1, 1996

By Y Omura

If dynamite is used in hot metal mines, it may be subject to decomposition, and the increase in nitroglycol vapour under the high temperatures causes bad headaches of workers. Also the explosives containing ammonium nitrate are very dangerous when mixed with sulfide ores at a high temperature!. Therefore we developed a heat-resistant water gel explosive which is safe to be handled at these hot metal mines.

Jan 1, 1983

By Paul Worsey, Terry Nixon

The development and testing of a simple mechanical stemming aid (Patents pending) resulting from a Joint venture by Incubator Technologies Inc. and the University of Missouri-Rolla and funded by the U.S. Department of Energy is described. The aid comprises a solid unit placed in the stemming above the explosive column and is designed to improve blasting efficiency and reduce drilling and blasting costs. It works with back filled drill cuttings or any other suitable stemming material.

Jan 1, 1988