Search Documents

By P. Prakash

A dual-drive planetary mill, which has a rotating shaft that sweeps a circle of diameter 750 mm, has been designed. The planetary mill is powered by a 5 hp motor to rotate the main shaft and a 3 hp motor to rotate the jars. The charge dynamics inside the horizontal-axis planetary ball mill was established using three-dimensional DEM simulations. The simulation results provided data to determine the impact energy distribution and the effect of process parameters such as mill speed and filling. It has been observed that the mean impact energy per unit time increases with rotation-to-revolution ratio, whereas the average number of inter-particle impacts per unit time decreases. The mill was also used to synthesize a variety of powders. Here three case studies of reaction milling are briefly presented: (i) cementite and silicon carbide, (ii) oxide dispersed strengthened (ODS) steel, and (iii) magnetite from blue dust. In each case, the powder was produced by mixing and then milling the corresponding pure components. The phase evolution, particle size distribution, and morphology of particles during milling were studied for various samples collected at different milling times using laser size analyzer, SEM, TEM, and Mössbauerspectroscopy. The results established a convenient way to produce powders of high technological and commercial value.

Sep 1, 2012

By S. Banisi, O. Farshid, M. R. Rozebehi, A. Bahar, A. Arghavani, M. Mahdavi

At the rougher flotation circuit of the Miduk copper concentration plant (Kerman, Iran) five column cells (CISA) with the diameter of 4m and height of 12m using static mixer type (MicrocelTM) spargers have been installed. Based on the initial design, columns should accept a feed rate of 625 t/h with 80% passing size of 90 µm and solids concentration of 28% and produce 88% of the plant concentrate (i.e., 22 t/h) containing 32% copper. Due to mechanical and processing problems this objective was never realized and theses columns were remained out of operation from the commissioning time (2005). A new attempt with the aim of returning these cells into operation started in 2013. The results of an extensive study indicated that spargers plugging due to the entrance of small amount (2 kg) of coarse particles (up to 2.5 cm) because of usual problems at the plant environment was the main reason of columns non functionality. With a change in the recycle pump inlet design to the column, which prevented the entrance of coarse particles to the spargers, the operation of the column significantly improved. It was found that in order to have a stable operation of the columns at the rougher stage the feed rate for each column should be reduced from 125 (design) to 70 t/h. The air superficial rate had to be also reduced from 1.9 (design) to 0.6 cm/s. A period of 10 days of continuous operation showed that the carrying capacity was 0.23 (g/min/cm2) which was significantly lower that of the design value (i.e., 0.58). The gas hold up was found to be lower than 10% beyond which columns started to move to the turbulent state indicated by "boiling" froth. The average life time of spargers was determined to be 20 days which considered to be very short. The average recovery and concentrate grade of these columns were found to be 68% and 32%, respectively. The high wear rates of spargers, unusually high level of maintenance and supervision needed and instability of the operation made the plant managers not to use column cells as the roughers.

Jan 1, 2014

By John A. Herbst, Ming Song, Xiangjun Qiu

"It has been known for sometime that as wear occurs in tumbling mills there is an associated change in mill throughput. These changes have traditionally been simplistically, attributed to “mill volume effects”. New high fidelity simulation (HFS) tools (involving DEM, CFD and Breakage models) are now giving new “microscale” insights into the complex interactions that occur between evolving lifter/liner profiles and breakage. An illustration of this analysis is shown in Figure 1 below.Here we see that after a new lining is installed (Region I) the wearing process reduces the liner thickness resulting in a larger power draw and an associated higher throughput until Region II is reached. By this point the lifter height is reduced significantly changing charge motion (less cataracting) the power begins to decline, but the comminution efficiency increases with this type of “calmer” breakage environment therefore the throughput continues to increase. In Region III the lifter is no longer providing the minimum required charge lifting action, the power and the throughput both drop off significantly. In the last two stages the behavior is especially complex because throughput is not linearly related to power since grinding efficiency is changing.The study described here shows that these new HFS tools allow the design of wear part profiles which will maximize mill productivity over the entire life of liner/lifter systems. A simple example of such a design procedure is shown involving the selection of a sinusoidal profile for a 34 ft diameter SAG mill.The paper discusses how the principles exposed in this simple example can be applied to search for an optimal profile in which non-standard modifications are allowed to compensate for throughput or wear shortcomings of standard profiles."

Jan 1, 2003

By Trevor Saldanha, Stephen Grano

A key uncertainty in flotation modelling is determining, a priori, the proportion of each mineral which will develop a certain rate constant for different feeds of variable liberation and hydrophobicity. First and foremost is the ability to predict the proportion of minerals that will not be recovered, even at very long flotation times, and which therefore report to the tailing stream as the non-floatable fraction (i.e., having a zero rate constant). Recent empirical evidence has shown there are at least two factors which contribute to heterogeneity in flotation rates and, in particular, the appearance of a non-floatable fraction - heterogeneity in the distribution of adsorbed collector amount on a particle-by-particle basis, even for the same liberated mineral in the same size fraction, and the existence of a critical contact angle below which the bubble-particle union is unstable. In this paper, inferred measures of the critical contact angle for liberated particles are compared with stability model calculations. This has demonstrated that the dependency of the critical contact angle with particle size and mineral specific gravity are explicable by bubble-particle stability considerations. This argument is further extended to the flotation behaviour of composite particles, as a function of liberation class, in which the wetting perimeter of the attached bubble on the composite particle surface is constrained by the presence of a surrounding hydrophilic domain for the case of simple binary composites. Reasons for the different flotation behaviour of composite particles having different textures, as noted in the literature, are also discussed in terms of the stability of the bubble-particle union.

Jan 1, 2014

By C. Tokoro

Co-precipitation of dilute toxic anions with ferrihydrite is an important removal mechanism in wastewater treatment system. Although, numerous qualitative studies have been published on removal characteristic from wastewater of dilute anions by co-precipitation treatment, detail mechanism or quantitative characteristic is not well understood. This paper discussed the co-precipitation mechanism of As(V) and Cr(VI) with ferrihydrite by comparative experiments between co-precipitation and simple adsorption. In this study, co-precipitation experiments and simple adsorption ones were distinguished closely. In the former, precipitation of hydroxides and adsorption of anions develop simultaneously, but in the latter, anions adsorb onto prepared hydroxides. Although high affinity anions for hydroxides (e.g. As(V) for ferrihydrite) showed quantitative difference of removal ratio between co-precipitation experiments and simple adsorption ones, low affinity anions (e.g. Cr(VI) for ferrihydrite) showed quantitative agreement in spite of deferent forms of ferrihydrites between them, that is, amorphous ferrihydrite was formed in co-precipitation experiments, but goethite was formed in simple adsorption ones. In order to discuss the mechanism of co-precipitation phenomena, three experimental studies have been carried out: (i) adsorption isotherm measurement in the co-precipitation experiments of As(V) or Cr(VI) with ferrihydrite, (ii) zeta potential measurement of co-precipitated or simple ad-sorbed ferrihydrite with As(V) or Cr(VI), and (iii) XRD analysis of co-precipitated As(V) for ferrihydrite. All experimental results suggested the main mechanism in co-precipitation phenomena of As(V) was not only a surface complexation (simple adsorption) but also a surface precipitation.

Jan 1, 2014

By R. Shiva Kumar, G. Sreedhar, S. Sharma

Some of the Indian origin iron ore deposits located in Bellary, Karnataka province are having peculiar characteristics of Iron ore deposits (Hematite) having Iron above 64% and 30-40% lump (-30+6mm) recovery which are not suitable to use in blast furnace due to not meeting the specification of Tumbler Index and Abrasion Index. In general for high grade Iron ores, process flow sheet involves crushing and screening (dry/wet). In the contest of high grade Iron ores located at Bellary sector of Karnataka state in India, lump generated from this process could not attain the required physical properties (Tumbler Index, Abrasion Index) and metallurgical properties , even though the grade of the lump ore is above 64% Fe. Washing techniques like Drum scrubber and Log washer play major role in improving the metallurgical properties of Iron ore lumps by removing the light and hard layers of clay, silica coated over the lumps. In this study the effects were compared of drum scrubbing and log washing on iron ore lumps. It is found that by incorporating simple washing technique i.e. drum scrubbing or log washing, Tumbler Index of Iron ore Lumps could be increased from 74% to 78% which is acceptable for use in Blast furnace. From the Drum scrubber and Log washer tests, it is clear that Log washers have an edge over Drum scrubber in removing hard coated clay on surface of Lumps. This simple washing technique facilitate us to utilize the lumps directly in blast furnace and eliminate the unnecessary crushing and grinding of the ore so as to meet the specifications of Sinter fines and pellet feed.

Jan 1, 2014

By Erico Tabosa, Kym Runge, Peter Holtham

"The distribution of turbulence in an industrial scale mechanical flotation cell and its effect on flotation kinetics was studied using a fully instrumented 3m³ cell. The cell was operated at a copper concentrator in Australia with different combinations of airflow rates, impeller speeds and sizes and cell aspect ratio providing a wide range of hydrodynamic conditions. An analysis of the overall flotation cell performance showed that the overall copper recoveries were very similar for the conditions tested. However, by decoupling pulp effects from froth effects it was possible to evaluate whether the changes made affected the pulp zone and/or froth zone responses. The analysis showed that the overall recovery has the potential to be up to 7% higher, if not limited by froth recovery. The cell hydrodynamics were characterised by the overall energy dissipation rate and, to understand the distribution of turbulence within the cell, localised measurements were made using a piezoelectric vibration sensor. By comparing the metallurgical performance of the cell with the different hydrodynamic conditions it was found that the collection zone flotation rate constant was not directly related to overall energy dissipation, as is commonly observed at laboratory scale, where energy is usually only changed by varying impeller speed. In this study, energy dissipation rate was varied using not only impeller speed, but also the size of the impeller and the cell aspect ratio. In these circumstances, the best correlation was found to be between the collection zone flotation rate constant and the distribution of turbulence, i.e. the size of the turbulent zone."

Jan 1, 2014

By H. Z. Kuyumcu

Coking of coal blends using high volatile coals with poor coking abilities to produce a high quality coke for blast furnace application can be achieved by compacting the coal blend prior to the carbonization process. Here densification up to a relative material density of 80 %, i.e. a compact density around 1100 kg/m3, has proven to be advantageous. Coal is compacted by stamping, if the so-called stamp charging process applied. Compacting of the coal by pressing is practised in case of the cokemaking with so-called heat-recovery ovens. Stamped and pressed coal cakes require over the cake volume uniform high density and mechanical stability. Besides the aspects of the coal selection, the efficiency of the process is mainly determined by the operating parameters compacting time and compacting energy for coal cake making. At the Department for Mechanical Process Engineering & Solids Processing of the Technical University Berlin the two sub-processes of densification and strengthening during stamping and during pressing are theoretically and experimentally investigated using specially developed lab-scale compacting test units and a strength test device. Describing cake density in terms of coal properties for a given coal and measured compacting energy input then leads to a compacting equation with the so-called Stampability as the integral model parameter for the stamping process. For the pressing process the cake density can be calculated with the measured compacting pressure and the Compressibility factor, respectively. Investigations were carried out to provide evidence of a significant influence of coal type, coal surface moisture, coal granulometric and mechanical properties on the densification process. The overall objective of the work is to establish a comprehensive mathematical model on the compacting behavior of large coal bulk quantities and the optimization of the compacting processes by stamping and by pressing. Keywords: coal compacting, agglomeration, stamping, pressing, cokemaking

Sep 1, 2012

By Remmerswaal, U. Boin, M. B. G. Castro

"To design sustainable products that can be recycled with high resource efficiency, low environmental impact and economic feasibility, the choice of materials and materials combinations, made in the design stage, is fundamental. The products we design, manufacture and use now will be the resources of the future. Designers are able to select materials for a product according to the many functional requirements they must fulfil. But they have a limited knowledge of the recycling processes and its requirements regarding quality of the secondary material streams. Resource Engineers have to manage the processing of these streams, that are becoming more complex with the increasing variety of materials and decreasing size of components. After mechanical separation of the materials streams resulting from shredding of EOL (endof- life) products, there is always a degree of contamination, from two possible causes:Incomplete liberation: the bonds between different materials combined in a component are not completely destroyed by shredding, resulting in some particles containing two or more materials attached;Separation efficiency: the mechanical separation processes are not able to separate perfectly the many material particles; there are always a number of foreign particles in the recovered streams.Sometimes, those contaminants cannot be removed by the industrial metallurgic recycling processes, and a more serious problem occurs when the contamination levels compromise the recycling of the material stream by lowering its quality (i.e. the properties of the recycled material will be lower due to the contamination). As a consequence, the material must be diluted in virgin raw material and/or used in a less demanding application (downgrading), causing resource depletion and increased energy use, waste production and recycling costs. In order to make the best choice of materials combinations for a product, a systematic approach is necessary, that can close the gap between the knowledge areas of Product Design and Recycling Technology."

Jan 1, 2003

By V. F. Petrov

Cyanide is widely used gold lixiviant for hydrometallurgical processes. The resulting tails contain complex toxic compounds. With reference to this, the protection of the environment should be the major issue. A complete detoxification of cyanides before disposal, a partial detoxification to the allowable concentrations and a disposal of tails at a polygon followed by the detoxification of excess water into the environment are offered as an environmentally friendly way of disposal. However, a complete detoxification of the cyanidation tails does not give the required results due to the presence of toxic compounds, cyanides and thiocyanates in tailings ponds. This is due to adsorption-desorption process occurring between solid and liquid phases. A partial detoxification is used to down cyanide to the allowable concentrations, which are safe to the environment. The storage of tails without detoxification is mainly used at low concentrations of toxic compounds in the disposed tails. With reference to this, water recycling is practiced by Russian plants in order to reduce as much as possible or almost eliminate toxic effluents into the environment. Fresh water is applied if necessary and to make up for water losses, with 8-12% of total water supply. This allows for the stability of water balance and the decrease of consumption of the reagents applied. The conditioning technologies of water recycling followed by regeneration of free cyanide and metals recovery as saleable concentrates are specially developed due to adverse impact of water recycling on gold recovery processes due to high concentration of base metals (copper). These technologies are also profitable. In order to detoxify cyanide in the tails for tailings dam, effective and inexpensive technologies involving a seasonal use of detoxified reagents were developed. For example, a technology with aldehydes use which is applied by a series of operations. Effluents disposed to the environment are detoxified using chlorination followed by almost a complete destruction of toxic cyanides and thiocyanates. Before disposal, chlorinated water is settled to precipitate the resulting hydroxides of metals and complete chemical reactions such as a full decomposition of hypochlorite ions. In order to protect ground water, watertight screens from local water-resistant materials are used. The samples of these materials were previously tested and chosen according to their maximum ability to adsorb toxic compounds in the tailings pond. If local water-resistant materials are not available, whole welded impermeable polymer screens are used. The options mentioned allow the storage of cyanidation tails in accordance with national ecological standards. Keywords: cyaninides, thiocyanates, wastes, environmental safety, recycled water-supply, detoxification, storage

Sep 1, 2012

By Paul W. Cleary

"Particle scale simulation of industrial particle flows using DEM (Discrete Element Method) offers the opportunity for better understanding the flow dynamics leading to improvements in equipment design and operation that can potentially lead to large increases in efficiency, throughput or product quality. DEM has been used for modelling many industrial applications, particularly milling. This includes ball and rock motions and power consumption in ball mills, AG and SAG mills, vibrational segregation, flows in rotating drums, operation of dragline excavators and hopper flows. In mineral processing, DEM has been concentrated on mills because of their critical importance. However DEM also offers the opportunity to improve many other parts of mineral processing operations. These areas often do not receive the attention that the key comminution equipment commands, but can become critical when they fail or under-perform. Importantly their assessment/improvement using DEM is often much more feasible because of smaller problem sizes and the absence of poorly understood physics such as breakage. In this paper we describe DEM simulations of four important pieces of non-comminution equipment that are commonly found in or near mineral processing plants (these are shown in Figure 1):"

Jan 1, 2003

The Indian steel industry is growing at a rapid pace and expected to be the 2nd largest steel producer in the world after China. To cope up with this growth and to sustain it, the industry needs to focus on effective utilization of domestic metallurgical coals. While the importance of indigenous coal has increased, its supply from the domestic sources is declining. This is primarily due to high ash content in Indian coals leading to its difficulty in washing to a low level competitive to imported coals. Non-availability of a suitable beneficiation technology to bring down the ash to such a low level is the other reason. Effective utilization of current technologies has enabled Tata Steel to bring down the ash to 13-16% from its captive collieries. However, further lowering the ash using the conventional beneficiation technologies is difficult and unsustainable. New technologies should be developed for bringing down the ash further. A thrust area research program has been undertaken at Tata Steel for producing clean coal with 8% ash maintaining the yield currently achieved in its washeries. The technologies attempted are based on chemical beneficiation of coal. In leaching process, suitable chemicals are used for extracting ash minerals from the coal. As an alternative process, the combustible part of the coal is being extracted using a suitable organic solvent through an organo-refining process. Both the processes have been successfully developed in the laboratory and are being demonstrated in pilot scales. Various beneficiation processes practiced at Tata Steel including the efforts made for developing new processes for achieving clean coal with 8% ash have been discussed in this paper. Keywords: metallurgical coals, washing, beneficiation technologies, chemical beneficiation, leaching, solvent, and organo-refining process

Sep 1, 2012

By Atul Kumar Bhatnagar

TATA STEEL is the pioneer in coal beneficiation in India. The first coal beneficiation plant was set up in 1951 at West Bokaro and subsequently in 1953 in Jharia. Over the years more beneficiation capacity was added by setting up new coal washeries in both West Bokaro and Jharia, the coal divisions of Tata Steel. currently the beneficiation capacity available is 8.5 mtp aappx Being a captive supplier supplying the coking coal as per demands of our steel works is challenging in the sense that the intent is to leverage the captive raw material advantage and select the best strategy for maximizing value up to steel making. The beneficiation plants were designed to produce clean coal up to 17% ash. With the demand of increasing productivity at the blast furnace the clean coal ash was lowered. subsequently the processes were audited and efficiency improved. The next challenge was to improve the throughputs in the existing plants to maximize the clean coal production. The upgradation was designed in house and implemented to upgrade the plant from nameplate capacity of 2.1 mtpa to 4.5 mtpa while the yearly production targets were also achieved. The presentation will detail the different phases of improvements, process followed, challenges faced, and the results as achieved in the process. Keywords: coal beneficiation, India, coal washeries, beneficiation plants XXVI INTERNATIONAL

Sep 1, 2012

By S. V. Petrov

Oxidised ores possess a significant share among raw materials which are treated by traditional plant technology. As usual, the chemical composition of these ores is rather simple. They can be treated by standard cyanidation. In this case, the resulting wastes have an alkaline reaction. Their toxicity (in case of ROM ores treatment) is mainly due to the presence cyanides and thicyanades. The tails are dexotified before disposal. However, chemical reagents used cannot provide a complete removal of toxic matters. In this case, this disposal poses a real problem because these tails contain a significant amount of CN and SCN and their behavior during a long disposal should be studied. A sample with a simple composition taken from cyanidation tails was studied. The sample presents itself the quartz low-grade sulfide gold-bearing ore. Sulfide sulfur content is 0.15 per cent,and heavy metals content is 0.023 per cent. Method of testing is described further. The samples were tested under moderate and subarctic climates based on the difference in temperature, moisture and the degree of oxygen saturation of air. The pH of water extract, which was prepared using distilled water, was also determined besides measuring the concentration of cyanides and thiocyanates. This demonstrates the stability of sulfide-bearing minerals in the disposed tails. The tests time was 820 days. It was found that the alkalinity of the samples tends to lower under oxygen-containing conditions in proportion to temperature increasing. Under conditions without oxygen, the pH lowering is minimal. Mineralogical and chemical properties of the ore material give positive alkaline balance during testing. The solid sample contains enough alkaline agents to compensate dangerous to the environment reactions of sulfides oxidation.pH value maintaining under alkaline conditions witnesses to the possibility of a safe disposal of this tails type. The largest amount of cyanide is removed under acid-containing conditions at positive temperatures. The higher the temperature is, the more intensive destruction is. At the moment, of finishing the tests at 20ºC temperature, the residual concentration of CN- was 0.06-0.10 mg/L, at 4ºC, the residual concentration of CN- was 0.2-0.3 mg/L and at -18ºC was 0.4-0.6 mg/L. Under conditions with the lack of oxygen, cyanides can be removed within the first 200 days. Then, this process fully stops. A stabilized cyanides concentration is 3.0-4.0 mg/L. The presence of sulfides increases the content of cyanides at the initial stage of testing. Then, the concentration of SCN at the temperatures above 0ºC decreases rapidly under oxygen-containing conditions. At the rise of temperature, a narrowing of peak at the curve and an increase of the destruction process are observed. At the end of testing, the concentration of thiocyanates in the moisture of wastes was 0.2-0.3 mg/L at the temperature of 20ºC and 0.5-0.6 mg/L at the temperature of 4ºC, respectively. The concentration of thiocyanates contained in a frozen sample and media which have the lack of oxygen stabilizes at a certain level owing to sulfides and does not practically change further. It was found that detoxification of oxidized cyanidation tailings with a simple composition which were disposed as filtration cakes can be possible. In this case, the concentration of cyanide in the moisture of disposed wastes can have a close value or equal to actual concentration during cyanidation. In order to meet the requirements of high ecological safety standards and successful detoxification process of toxic compounds in the tails under the action of natural factors, the conditions of air aeration with oxygen for the whole volume of tails are required. Keywords: cyanides, thiocyanates, storage, detoxification, flotation cakes

Sep 1, 2012

By M. V. S. Cavalcante

The quality of iron ore pellets, represented in terms of parameters such as cold compressive strength (CCS) and Tumble Index (TI), has a strongly influence on the productivity and energy of reduction furnaces like the blast furnace and on the quality of hot metal or liquid iron. The main objective of pelletization operations is to produce iron ore pellets of desirable specifications and ensure high levels of plant productivity and energy efficiency. Advanced process control of an industrial iron ore pellet induration process using a soft sensor for pellet quality and fuzzy-logic based control algorithm is described in this paper. The pellet quality soft sensor consists of a rigorous mathematical model of the induration process and a statistical model for the pellet quality parameters. The mathematical model is based on the fundamental principles of heat and mass transfer between gases and pellets, kinetics of drying and condensation of moisture, combustion of coke, calcination of limestone, and melting and solidification of pellets. The predictions of wind-box temperature profiles are in close agreement with the measured profiles. The time-temperature profiles of the pellets during induration, along with raw material characteristics and induration process operating conditions, are used as inputs to the quality model to predict cold compressive strength and the Tumble Index. The predictions of the quality soft sensor along with the rules based on fuzzy-logic derived from simulation results and operator experience are then utilized to control the induration process to achieve precise control of the quality parameters and to optimize the induration process in terms of fuel efficiency and productivity. The mathematical model is also utilized as a soft sensor for temperature, moisture and composition profiles of pellets and gases. Results of implementation of this model-based control strategy on an industrial scale induration process will be presented. Keywords: iron ore, pelletization, simulation, process control, optimisation

Sep 1, 2012

By Dilip Kumar Mohanty

In today?s world, Sustainability is the key issue before the mankind. With the ever-increasing population & unimaginable boost in industrial growth to cope up with a steady increase in demand and fast change in life style of a human being, the natural resources are exploited to such an extent that the very existence of living beings in this earth planet is threatened. In such devastating situation, the concept of Sustainability emerges out as a great savior. This concept focuses on minimum/ judicious use of natural resources, thereby preserving the resources for future generation while meeting the bare minimum requirement of the present generation. For an emerging economy like India, Mining and Mineral based industries form the back bone of our economic development. Thus, sustainability of mining and mineral processing industry has a far reaching impact on sustainable economic development of our nation. While at a macro-economic level, we have to strike a balance between economic development vis-à-vis socio-economic & environmental impacts, Industries have to ensure judicious and frugal use of natural resources by making use of energy efficient plants & machineries and adopting befitting technology for reduction & recycling of waste. In the context of the above, it would be interesting to look into the sustainability measures taken up by National Aluminium company (Nalco) at its Crushing & conveying plant at Panchpatmali Bauxite Mine, which is incidentally Asia?s largest Bauxite Mine. In the backdrop of the above stated facts, in this paper the authors make an attempt to bring out the sustainability issues in areas of energy conservation, environmental impact/pollution vis-a-vis mitigation measures adopted in crusher & conveyor plant of Panchpatmali Bauxite Mine & CSR / peripheral developmental activities undertaken by Nalco to mitigate the socio- economic impacts. Keywords: sustainability, energy efficiency, recycle, csr, peripheral development

Sep 1, 2012

By T. C. Rao

This presentation identifies how mineral (coal included) processing profession should look at the challenges (threats) being faced by mineral industry. Presently, the focus is more on supply and demand on minerals. In addition, the R&D activities in the chain of mine-to-metal are paying more attention (if not only on) the processes being adopted, development of new equipments and modeling and simulation. But the profession is grossly ignoring aspects such as impact of the processes on other resources, of the ways we extract, use and dispose them socio-economically and efficiently. A business model which may encompass all these dimensions are essential for the sustainable development of mineral industry and a possible approach in this direction is presented. To start with, for the sustainable growth and existence, the profession must be aware of the prospective impacts of their activities on critical factors such as ? political (changing government policies), geographical (environment, land, water and habitat), which have major bearing on the survival and growth of the industry. Mineral Processing professionals have to join hands with mining engineers to answer some relevant questions related to the impact of mineral industry on society. Mining can become economically viable only if mineral processing engineers come out with innovative solutions to reduce capital and operating costs. The solutions have to be adoptable and practically feasible so that industry looks at us for directions. In fact, we have to move towards beneficiation of nano particles striving towards zero waste. Some of the gaps in the knowledge of procedures being followed in the design and operation of processing plants are highlighted. Enhancing the knowledge base for solving unexplored possibilities, solutions to evolve sustainable development measures which demands innovation both at academic and practicing levels is the need of the future. Well-structured academic programmes are to be formulated so that the graduates of these programmes can make an effort to look at processes/concepts with a new insight and approach; the profession should excite the young brains with challenges. R&D funding agencies have to have a long-term perspective on mineral processing so that closer interactions between academic institutes, industry and R&D organizations are sustainable and that innovations are at least a few years ahead of needs of future challenges. Keywords: sustainable growth

Sep 1, 2012

By Z. B. Pan

The innovative point of this new technology can be described that under normal pressure and 70°C, using a new combined activating and oxidizing agent, the minerals bearing arsenic and organic carbon are oxidized effectively. This technology can be applied in commercial scale. The high carbon and arsenic bearing gold ore is taken from Gansu, where hundreds of tons gold deposit. The ore has 0.51% of arsenic and 1.75% of carbon (1.07% of organic carbon). The gold occurs mainly in native with particle size 0.02~0.6 mm and a few are enwrapped by pyrite and arsenopyrite. The traditional cyanide leaching process gains a very low gold leaching rate with only 5%. Through systemic experimental study, the technological flowsheet of flotation process for concentrating gold, then pre-treating the gold concentrate followed by cyanide leaching the gold concentrate are used. With 4.92 g/t gold of head sample, the gold concentrate with 46.52g/t gold grade and 96.53% gold recovery is gained by flotation process. Followed by pre-treatment for 6 hours, the gold concentrate is leached with cyanide after filtration and washing. The total gold leaching rate is up to 95.44%.

Jan 1, 2014

By Q. W. Jiang

This paper presents a new process for producing industrial magnesium sulphate using waste water from titanium white plant and magnesium oxide from calcinations of magnesite ore as raw materials. With the laboratory experimental equipment, the waste liquid and magnesium dioxide react effectively at ambient temperature and under atmosphere pressure. Via the press filter, a clear liquid predominately containing magnesium sulphate is obtained. It is further evaporated and crystallized by cooling, separated by centrifuge and dried. Consequently a high quality of industrial magnesium sulphate is achieved as the final product. In the course of process, as the majority of valuable component (SO42-) is recovered in the final product, most of impurities from waste acid is being removed into the by- product. With the simple operational process, it is possible for titanium dioxide plant to resolve the environmental problem completely and benefit from the industrial magnesium sulphate product as well. The filter cakes containing valuable elements such as Mg, S, Fe, Mn, V, Ti are by-product proposed to be used for manufacture of agriculture fertilizer particularly for peanut planting.

Jan 1, 2014

By Yuhe Tang

High Gradient Magnetic Separator with Horizontal Magnetic Line is a new type High Gradient Magnetic Separator product. It has many specific advantages, such as water-air joint discharging technique, double pulses pulp dispersion technique, multi-magnetic gradient for collecting matrix with different diameter rods, better discharging rate with the especial matrix dispose, high separating accuracy and wide applicability. In this paper, the author makes a description of High Gradient Magnetic Separator with Horizontal Magnetic Line, and puts its emphasis on analyzing industrial production data using high gradient magnetic separator with Horizontal Magnetic Line to separate weakly magnetic minerals. It is found that as the rougher for weakly magnetic minerals separation, High Gradient Magnetic Separator with Horizontal Magnetic Line has more stable metallurgical performance and cheaper running costs than other types of High Gradient Magnetic Separator when the properties of the ore change greatly and there is in the case of embedded fine particle size distribution. Keywords: high gradient magnetic separator, self cleaning technology, horizontal magnetic line, water air discharging technique

Sep 1, 2012