Search Documents

By Harold Gibson, Ulrich Schwarz-Schampera, Ralf Freitag, Hendrik Mueller

INTRODUCTION Germany has a long history in marine research in the Indian Ocean. The first German scientific cruise started in 1964, followed by a series of state-sponsored research cruises between 1983 and 1995 leading to the first finding of polymetallic sulfides in the Indian Ocean. The research included regional bathymetric, geological, structural, volcanological, petrological and hydrothermal investigations along the Carlsberg Ridge and the Central Indian Ridge (CIR). Early environmental base line studies covered oceanographic and sedimentology aspects. In 2010, BGR took the initiative for the preparation of a license application for the exploration of polymetallic sulfides with the International Seabed Authority (ISA), and prospecting started in 2011 along the southern Central (CIR) and the northern Southeast Indian Ridge (SEIR) in the southwestern Indian Ocean (cruises INDEX 2011 on board R/V Sonne), INDEX 2012 (R/V Fugro Gauss), INDEX 2013/1-2 (R/V Sonne) and INDEX 2014 (R/V Pelagia). After three years of resource-oriented and environmental base line studies, BGR, in order for the Federal Ministry for Economic Affairs and Energy (BMWi), applied for an exploration license which was approved by and subsequently signed with the ISA in 2015. The license gave permission to start a detailed exclusive resource-oriented exploration program in the license area. The program includes the outline of potential ore deposits and a resource assessment but also extensive and detailed base line studies for the sustainable protection of the marine environment in the license area. The license contract has a fifteen years lifetime and may allow the application for a subsequent mining license. The exploration aims at the identification of inactive polymetallic sulfide deposits, formed below former discharge zones of hot hydrothermal fluids on the ocean floor (“black smoker” systems), by advanced and modern exploration techniques.

Jan 1, 2018

By Roger Amato

The 1982 United Nations Convention on the Low of the Sea includes provisions under Article 76 for extending a coastal State's jurisdiction beyond the 200-nautical-mile (nm) Exclusive Economic Zone (EEZ) and for establishing the seaward limits of sovereign rights over natural resources. Article 76 prescribes a set of methodologies for determining these outer limits based on physiography and sediment thickness. The methodologies were applied to each of the five continental* margin areas of the United States - Atlantic, Pacific, Gulf of Mexico, Alaska, and Pacific Islands-using existing digital hydrographic and geologic data. Figures 1 and 2 show the results of applying the methodologies to the Atlantic, Pacific, Alaskan, and Gulf of Mexico continental shelves. Figure 1 depicts the preliminary limits of each of the Article 76 determinations for the Atlantic and Gulf of Mexico continental shelves. The Atlantic limits were described by Carpenter, Thormahlen, and Amato (1995) at the 26th Underwater Mining Institute.1 The limits for the Alaskan continental shelves are shown in Figure 2. Additional areas beyond the 200 nm EEZ are highlighted. These include a small area north of the U.S. - Canada boundary, containing 7,000 km2, a large area north of Point barrow (395,000 km2), and a third area north of the Aleutian Islands (178,000 km2). The shelf between the first two areas appears to have sediments thick enough to qualify for the 1 percent method (Irish Formula); however, year-round ice cover has prevented acquisition of seismic or drill data. The entire northern Alaska shelf is prospective for petroleum The Gulf of Mexico (Figure 1) has two small areas beyond the EEZ known as "doughnut holes." One is south of Louisiana and includes part of the Sigsbee Escarpment, an area believed to have potential for oil and gas. Oil was found on Sigsbee Knoll in cores from Deep Sea Drilling Project's Leg 1 cruise in 1968. The Sigsbee areas contains about 6,000 km2. The second area is south of the Florida panhandle and contains about 12,000 km2.

Jan 1, 1996

By Audrey Boissier, Marie-Anne Camon, Cecile Cathalot, Yves Fouquet, Laurent Bignon, Arnaud Agranier, Ewan Pelleter, Sylvain Bermell, Florian Besson

INTRODUCTION In October 2014, on behalf of the French government, Ifremer, along with the International Seabed Authority (ISA), signed a contract to start a detailed exploration program for seafloor massive sulfide (SMS) deposits in the work plan located on the slow spreading Mid-Atlantic ridge (MAR). The contract has a fifteen-year lifetime and the related exploration program must include the outline of SMS deposits and a resource assessment, as well as detailed environmental base line studies in the contract area. The exploration for SMS deposits generally includes detection of hydrothermal plume anomalies, acquisition of surface and near-bottom geophysical data, sampling operations from the research vessel (e.g. dredges, cores), and dive operations. The environmental studies include, among others, short and long-term oceanographic measurements, water column studies, biodiversity evaluation close and far from SMS deposits, characterization of natural hydrothermal plumes and related sedimentation. The HERMINE research cruise held from March 13th to April 28th 2018 (R/V Pourquoi Pas?) was the first cruise dedicated to exploration of active and inactive SMS and to the quantification of natural chemical input to the water column. The HERMINE cruise strategy was built up around three main objectives: (i) regional exploration including the detection of plume anomalies and the research of SMS deposits, (ii) local exploration of a SMS district and (iii) integrated study of a natural hydrothermal plume. This 3-in-1 cruise required us to optimize the switch between dives and surface operations. Day-time was devoted to dive operations whereas night-time was mostly dedicated to CTD/Rosette operations. The Nautile HOV (Human Occupied Vehicle) was well suited to the working time schedule of the cruise because it was time efficient in shorter (i.e. < 10h) dives due to fast descent and ascent speed, fast submerged forward speed, high maneuverability and the ability to carry heavy science payload as well as large volume of samples. Regional Exploration The first seventeen days of the HERMINE cruise were devoted to regional exploration, i.e. the detection of new plume anomalies and the research of new sulfide mineralization in the French work plan (10 000 km2; 6 clusters).

Jan 1, 2018

By Youngtak Ko

The northeastern Pacific shows the highest nodule abundance among the oceans in the world, and thus has been drawing international attention for deep-sea manganese nodule development. The objectives of this study are to construct database using geostatistics and geographic information system (GIS), to quantify rating value using probability and statistical methods, to suggest suitable sites for manganese nodule development, and to verify results using three statistical approaches. The copper and nickel contents of the nodules were determined by chemical analysis. Factors related to slope, aspect, water depth, and topography were obtained from multi-beam echo sounding data. The transparent layer thickness was determined using a sub-bottom profiler. The probability method was used to calculate each factor&apos;s rating, and the layers for different factors were summed to produce the development potential index (DPI). Result maps were constructed for manganese nodules development. The distribution pattern of DPI showed to be controlled of nodule abundance and metal contents. Verification was performed by comparing the results with sampling data in three ways: success and prediction rate, linear regression, and test of independence.

Sep 14, 2011

By James R. Hein

A new data set of cobalt-rich ferromanganese (Fe-Mn) crust chemistry has been completed for the first detailed sampling of a latitudinal crossing of the Pacific equatorial zone of high biological productivity. Samples were collected in January-March, 1999, during the AVON 2 cruise aboard the R.V. Melville, Scripps Institute of Oceanography. Samples were collected from 4.6° N to 9.2° S latitudes along two ridges, the Marshall Islands-Gilbert Islands ridge (4.6° N to 3.5° S) and the Howland Island-Tokelau Islands ridge (1° N to 9.2° S). The two ridges are offset east-west in the region of overlapping latitudinal sampling by about 466 km. We determined the concentrations of 48 elements for 147 samples from 39 dredge hauls taken on 33 seamounts and island flanks that occur between the Marshall Islands to the northwest and Samoa to the southeast. Element concentrations can be examined as varying spatially and with water depth in the ocean and we examine those relationships based on statistical analysis of the chemical and spatial data. The mean Fe/Mn ratio of 1 and mean Co content of 4645 ppm are typical of West Pacific hydrogenetic crusts; but the mean Co content is low compared to those of some equatorial North Pacific sites, such as the Marshall Islands and Johnston Island EEZs. In contrast, the mean Cu concentration (1540 ppm) is 35% higher than the mean concentration for Pacific Ocean Fe-Mn crusts (998 ppm). Another striking difference is the 40% higher Ba concentrations (mean 3107 ppm) compared to typical Central and West Pacific crusts (mean 1876 ppm); but Ba concentrations are lower than those in California continental-margin Fe-Mn crusts (mean 4085 ppm). A final significant difference in Fe-Mn crust chemistry is Zr concentrations, mean 921 ppm (maximum 1523 ppm), which is about 30% higher in this data set compared to the previously determined mean value of 613 ppm for Central and West Pacific crusts. Zirconium has a strong positive correlation with Ba and a weak positive correlation with Mn.

Jan 1, 2003

By Sven Petersen

The southern Mid-Atlantic Ridge (SMAR) is one of the least-explored spreading centers in the world with respect to hydrothermal activity. In the past 8 years research focused mainly on the ridge segments close to Ascension Island, discovering hydrothermal fields as far south as 14°20?S (Haase et al., 2007; German et al., 2008; Tao et al., 2011). However, the vast majority of the SMAR ridge axis has never been thoroughly investigated for hydrothermal activity. In the spring of 2013 we used segment-scale AUV deployments as well as conventional CTD surveys to identify areas of hydrothermal activity along 16 mid-ocean ridge segments between 13° and 33°S, thereby covering close to 5 % of the global ridge axis in a single cruise. During cruise MSM25 of the German research vessel Maria S. Merian, we tested longrange (>100 km lines per dive) AUV deployments of GEOMAR?s AUV ABYSS (a Remus 6000 vehicle) along the spreading axis for their capability to locate active venting in a fast and efficient way on regional surveys. Since the missions covered long distances,

Sep 14, 2011

By Darryl Thorburn

The Cook Islands are 15 islands located in the Southwest Pacific (between 8-23°S latitude and 156-167°W longitude). The total land area is about 200 km2. However, because its islands are widely scattered, the EEZ of the Cooks encompass an area about 2 million km2. The Cook Islands government exercises sovereignty and jurisdiction over its EEZ according to international law and convention as a member state under UNCLOS1. Accordingly, the Cook Islands government exercises full control over resources in its EEZ, including minerals on the seabed. Decision making on allocating licences for exploration and ultimate mineral recovery is by the Cook Islands government and will be set out in relevant statutes. Seabed minerals investigations within the EEZ of the Cook Islands and adjacent waters were first carried out by, USSR, US, and New Zealand research vessels in the late 1960 early 1970?s and indicated the presence of high concentrations of manganese nodules. This early work was followed by a number of Government funded surveys in and adjacent to the Cook Islands EEZ These surveys have identified a world class resource of manganese nodules within the Cook Islands EEZ (CI EEZ), containing significant

Sep 14, 2011

By Randolph A. Koski

Since 1985, numerous constructional sulfide-sulfate deposits in the form of mounds, pinnacles, chimneys, and sheets have been located between 40°45&apos; and 41°05&apos;N latitude in Escanaba Trough, the sediment-covered axial valley of the Southern Gorda Ridge. Single-channel seismic data indicate that three volcanic edifices up to 6 km in width penetrate as much as 500 m of turbidites that fill the valley; pillow and sheet flow lavas are exposed on the sea floor where these volcanoes breach the sediment surface. Observations from deeply towed camera systems and submersibles show that the largest hydrothermal deposits occur along the step-faulted northern flank of the central volcanic edifice and on the peripheries of steep-sided, sediment-capped hills, approximately 1 km wide and 100 m high, that rise above the valley floor. The sulfide deposits are highly oxidized, eroded, and partly buried by unconsolidated sediment; aprons of sulfide talus extend downslope from the mounds. Two types of sulfide have been sampled by dredging and submersible. The predominant mound and chimney material is pyrrhotite-rich massive sulfide with low amounts of Zn, Pb, Cd, and Ag. Coarse-grained zones with high porosity mark the location of myriad fluid channelways. Thin crusts of barite associated with pyrrhotite-rich sulfide have Au contents up to 2 ppm. Zoned fragments of polymetallic (Fe-Zn-Pb-Cu-As-Ag-Sb) sulfide dredged from a single site near 41°01&apos;N latitude are part of a chimneylike vent structure with a

Jan 1, 1988

By G. Rehder

The release of methane as free gas from the seafloor into the water-column well within the hydrate stability field is a natural process observed today in various ocean settings, such as the Cascadia margin, the Black Sea, the Guayamas Basin, and the Gulf of Mexico. The subsequent dissolution of gas bubbles into the water-column determines the vertical distribution of aqueous methane in the water-column and the upwards methane flux. Understanding this process not only is essential to describing the impact of natural deep-sea gas seepage, but also to assessing the hazard potential from blowouts and offshore exploitation activities, which are steadily expanding to greater ocean depths. Furthermore, the fate of methane from seeps contributes to scenarios of global change in the past and future involving the large scale destabilization of gas hydrates on a. We recently reported on the extended lifetime of methane bubbles within the hydrate stability field due to the formation of a hydrate skin (Rehder et al., 2002), based on in situ measurements of methane and argon bubble dissolution in the depth range 400 to 800 m. More recently, these observations were extended to depths from 900 to 1500 m. Single bubbles were injected from the ROV Ventana into an attached, back-illuminated, flow-through imaging box. The ascent of individual bubbles within the imaging box was recorded with Ventana?s HDTV camera system by piloting the 3-ton ROV upward, at the bubble rise velocity, for up to 400 m of vertical transit. Observed rise velocities were approximately 30cm/sec for all depths. Post-dive analysis of the HDTV video allowed detailed measurements of the bubble shrinking rates. The results of the earlier and new experiments lead to the following conclusions: (A) Methane bubbles released below the hydrate stability field showed markedly enhanced lifetimes, attributed to hydrate skin formation. The change in radius with time, dr/dt, varied from -7.5 micrometer/s above the hydrate stability field to about -1 micrometer/s at the deepest release depth. (B) Bubble lifetime within the hydrate stability field increased with distance in P-T space from the hydrate phase boundary. (C) Before hydrate skin nucleation, dr/dt for CH4 bubbles was comparable to dr/dt above the hydrate stability field. Although variable, the onset time for the hydrate skin effect to occur generally decreased with distance from the hydrate phase boundary (super-pressurization and super-cooling with respect to hydrate formation). (D) Even before the onset of the hydrate skin effect, a slight decrease of dr/dt with increasing depth was observed.

Jan 1, 2005

By Dennis Sánchez Mora, John Jamieson

INTRODUCTION Work by Humphris et al., (2002); Ondréas et al., (2009); Barreyre et al., (2012); and Escartín et al., (2015) has identified active and inactive hydrothermal sites along the Lucky Strike segment. The sites that contain the largest accumulation of known sulfides are located between the north and the southern zones (Figure 1), a vent site area that is referred to as the Main Lucky Strike hydrothermal field (Escartín et al., 2015). Hydrothermal fluid outflow has been linked to a shallow fault network (Barreyre et al., 2012). However, specific constraints on fault geometries have not been determined. Other off-axis sites at Lucky Strike, such as Capelinhos (high temperature vent), and Grunnus (inactive?), as well as a low temperature vent field (on-axis), Ewan, have been described by (Escartín et al., 2015). Given the spatial relationship between the Main Lucky Strike hydrothermal field (MLSHF), and the intersection of northern rift faults with the southern rift faults, a structural analysis of this area can provide insight into the fault controls on fluid flow that leads to hydrothermal venting and sulfide precipitation. METHODOLOGY Structural data (dip direction and dip) was determined using Leapfrog Geo 4.0 software. Bathymetric data was obtained from Escartín et al., (2015) and references therein. The bathymetry was imported into Leapfrog Geo (in UTM format) and, using the structural modelling tool, individual measurements with dip direction and dip data were collected with a focus on the northern volcanic rift and the southern central volcano (Figure 2a). All measurements were taken from what the authors consider as normal faults, and to aid the determination of individual measurements a “face dip” map was constructed, where the bathymetry is colored by slope angle (Figure 2b). All measurements are simultaneously plotted on a stereonet generated by the Leapfrog Geo Software. Data were divided into northern and southern, and western and eastern zones to determine the relationship between hydrothermal venting and the structural geometries at Lucky Strike (Figure 2c). Slip measurements for individual faults were determined along the dip of the fault with a measuring tool. Net slip, heave (horizontal displacement), and throw (vertical displacement) was calculated for each of the zones.

Jan 1, 2018

By Øystein Sture, Kurt Aasly, Ben Snook, Sigurd A. Sørum

INTRODUCTION Efficient exploration methodologies for base metal deposits have huge benefits for future deep sea mining endeavours, and underwater hyperspectral imaging (UHI) has been variably demonstrated to have applications in the identification and characterisation of mineralisation on the seafloor for both nodules and seafloor massive sulphides (SMS) (Dumke et al., 2018 and 2017 respectively). Due to growing resource requirements (Singer, 2017), SMS deposits are considered to be increasingly significant sources of copper and zinc, as well as silver and gold. This style of mineralisation is currently occurring at active hydrothermal vents (black and white smokers) but now-inactive sites also have the potential to be large mineral deposits. As such, the development of novel methodologies to detect both on-going and extinct mineralisations are of high importance. Geological setting During the MarMine cruise (Ludvigsen et al., 2016), non-mineralised host rock, low grade ore and high grade ore grab samples (Snook et al., 2018) was collected by ROV from the Loki’s Castle deposit (Pedersen et al., 2010), located on the Mohn’s/Knipovich junction on the ultra-slow spreading Arctic Mid-Ocean Ridge (AMOR), at a depth of approximately 2300 m. This material has been characterised as part of the MarMine project (e.g. Snook et al., 2017), and, by imaging compositionally constrained material, the measured hyperspectral responses can be used to generate a library for identification of deposits on the ocean floor. UHI technology Remote sensing with hyperspectral and multispectral technologies has seen wide use in prospecting for ores and hydrocarbons on land (Van der Meer et al., 2012). Iron oxides and sulphides have low blue reflectance and high red reflectance in the visible spectrum. The ratio between these two pairs has been used in exploration for terrestrial deposits of hydrothermal origin (Sabins, 1999). This discrimination typically also includes wavelengths exceeding the visible spectrum (1.5µm – 2.5µm). These wavelengths are typically not utilised underwater because infrared wavelengths and higher are rapidly attenuated in water. However, discrimination based on the full shape of the spectral response in the visible light (350nm – 800nm) may still be possible (Bolin and Moon, 2003). Resolving the endmembers from the spectral responses requires prior knowledge about the optical properties of the materials, i.e. their reflectance. These reflectances can be obtained in a controlled environment, where the spectra of the lamps, wavelength- dependent attenuation in water and scattering of light can be accounted for (Johnsen, 2013).

Jan 1, 2018

By Ivar Eskerud Smith, Ole Jørgen Nydal, Niranjan Reddy Challabotla, Svein Sævik

INTRODUCTION Airlift pumping, utilize compressed air that is injected at the bottom of a vertical pipe submerged in the water, reduces the mixture density inside the pipe and lifts the liquid or mixture of liquid and solids. This type of pumping technology, which is simple and without moving parts submerged in water, which provides several advantages compared to the mechanical pumping. Airlift is used in various difficult pumping applications such as transport of fluids corrosive to metals, explosives, nuclear and toxic materials in chemical industries, diamond mining and coal transport. Application of airlift to deep sea mining conditions was investigated by extensive laboratory experiments [1], theoretical analysis [2], and limited proof of concept field studies [3] starting in 1970’s with the discovery of huge amounts of manganese nodules discovered on the seabed at a depth of ranging from 4000 to 6000 m . Even after extensive investigations over the last five decades, there exists no commercial application of airlift technology for lifting of minerals. The major problems with the application airlift for deep ocean mining was (a) lack of control over the expansion of the injected gas, which increases the velocity in upper part of the riser pipe (b) lower efficiency compared to mechanical pumping [3]. Different flow regimes are encountered in airlift pumping: bubble, slug, churn and annular flow. Annular flow regime is the least efficient in lifting of particles and churn flow has better efficiency [3].

Jan 1, 2018

By Yannick Beaudoin

The source of base metals in modern seafloor hydrothermal systems can be attributed to leaching of host rocks by hydrothermal fluids and/or potentially by direct degassing of magma. From an economic perspective, metal grade is the most important consideration for seafloor deposits. Tectonic setting appears to be a key factor influencing the development of high grade seafloor base metal sulfide deposits. Back-arcs have a clear advantage over other settings in producing large and rich polymetallic sulfide ores. Microinclusions of magma or so-called melt inclusions trapped in phenocrysts of lavas have contributed to our understanding of the ore-forming process. n this study, we present data from 103 melt inclusions mainly in plagioclase crystals hosted in basaltic to rhyolitic lavas from 9 modern seafloor tectonic settings: oceanic back-arcs (Manus Basin including an ODP Leg 193 drill hole, Bransfield Straits), continental back-arc (Okinawa Trough), mid-ocean ridges (Explorer, MAR), seamounts (Foundation, Axial, Pito), and a transform (Garrett). Most sites host active hydrothermal systems that are producing polymetallic sulfides.

Jan 1, 2005

By Felix Lehnen, Peter Kukla, Mirjam Rahn

"Significant uncertainty is associated with predicting future trends in deep-sea mining projects, especially when attempting to assess markets for associated products such as ships and collectors. In order to help European Original Equipment Manufacturers (OEMs) to appraise the future market share of deep-sea mining equipment, a methodology was developed that allows to assess and predict equipment turnover. This study presents a market analysis, which evaluates the scale of the potential market for deep-sea mining equipment for seafloor manganese nodules (SMnN) and seafloor massive sulfides (SMS) based on six key drivers: (i) the worldwide deposit potential of SMnN and SMS deposits, (ii) the profitability of deep-sea mining projects, (iii) the metal market of seven associated metals (Cu, Zn, Au, Ag, Co, Ni, Mn), (iv) the current legal and environmental situation in the Area, (v) investment and maintenance costs, and (vi) a competitor analysis.Figures for the different key drivers are based on public reports and expert interviews. Large uncertainties as well as contrasting views and expectations resulted in different options (scenarios) for the future development of the deep-sea mining market. Several scenarios were developed and based on the future number of “mining projects” in the short-term (2022-2041) and the long-term (2042-2061). The number of such mining projects has been calculated based on the combined analysis of the different key drivers.In the scope of this study, the definition of a “mining project” is a deep-sea mining operation for SMnN or SMS lasting for 20 years. This operation includes the purchase of a set of deep-sea mining equipment consisting of a mining support vessel, a vertical transport system and the seafloor mining equipment, in line with other work within the EU FP7 project “Blue Mining” (GA No. 604500)."

Jan 1, 2017

By Delphine Pierre, Jean-Marie Augustin, Anne-Sophie Alix, Charline Guérin, Cecile Cathalot, Yves Fouquet, Arnaud Gaillot, Ewan Pelleter, Carla Scalabrin, Florian Besson

With the world’s growing demand for metals, seafloor massive sulfides (SMS) deposits are now seen as a possible mineral resource that could contributes to secure metal supply for human needs. SMS deposits are characterized by high concentrations of base metals and at some place high contents of precious and rare metals. Since 1977 and the discovery of the first high temperature (HT) hydrothermal vent and its sulfide mineralization and high biodiversity, more than 300 sites are known today. If the exploration strategy for detection of active hydrothermal sites is now robust, their associated mineralization will not (and must not) constitute a potential target for deep-sea mining due to environmental concerns and technical limitations. Recent studies on SMS deposits are rather focused on extinct and buried mineralized sites characterized by a lower biomass. Several geophysical techniques to explore and detect extinct SMS (eSMS) and buried SMS (bSMS) have been developed (e.g. Kawada and Kasaya, 2017; Szitkar et al., 2017, 2014) using different approaches (e.g. regional or local scale; ship-based or using underwater vehicles) with several degrees of success or limitation. Here we present results from acoustic surveys performed on the TAG hydrothermal district during the BICOSE (2014) and LEVE-SMF (2016) cruises and direct observation provided by HOV (Nautile) dives carried out during HERMINE cruise (2017). Acoustic data were acquired using two different multibeam echosounders (MBES): the hull-mounted Kongsberg EM122 (12 kHz, R/V L’Atalante) and the ROV-mounted RESON SeaBat 7125 (400 kHz, ROV Victor) (Figure 1). After processing, acoustic seafloor backscatter data from both MBES provides complementary qualitative results in relation to the seafloor composition. The analysis of the seafloor backscatter data obtained by near-seafloor surveys with the high-resolution 400 kHz MBES shows a clear relationship between low backscatter strength values and areas covered with pelagic and hydrothermal sediments whereas high backscatter strength values are associated to pillow lavas and basaltic scree. Intermediate backscatter strength values are rather related to old and younger eSMS as well as to mineralization on TAG active mound.

Jan 1, 2018

By Ning Yang, Sup Hong

INTRODUCTION Metal components contained in deep-seabed mineral resources are being highlighted as “energy metals”, which are widely utilized in the entire fields of energy: harvesting and generation, storage and transportation, and saving. Those are mostly trace and rare metals, and rare earth elements as well: manganese, nickel, cobalt, copper, molybdenum, tellurium, selenium, platinum, etc. Toward low carbon society, for global sustainability, the role of metals and minerals is growing up in industries of energy and transportation [1]. In this context, the production and supply of energy metals from deep seafloor have to be approached also based on sustainable development. In deep-seabed mining activity, the sustainability is focused on potential impacts on ecosystems in benthic area and water column. The environmental impacts in deep-seabed mining are caused basically by intervention in benthic zones and transportation of materials. Those are, in particular, removal of benthic habitats, generation and dispersion of sediment plumes, surface transportation of seawater and sediment, tailing from mining vessel, sound and light noises, and chemical leakage, etc. This paper is aiming at fundamental guidance towards sustainable mining of polymetallic nodules.

Jan 1, 2018

By Valcana Stoyanova

Data and information for this study were collected in June-July 2009 onboard the RV Yuzhmorgeologiya in the area covers about 7000 km2 in the eastern part of the CCFZ between 10º05? - 10º55?N and 119º25? ? 121º08?W. In accordance with the IOM research program the cruise was intend to acquire both geological and environmental data and information necessary for delineation of nodule deposits and also data for identification of the baseline of benthic ecosystem. Having implementation of its 15-year plan of work for exploration under the contract with ISA, current activities of IOM were focused on nodule fields within prime areas that could be mined in the future. Bottom photographs obtained by towed deep-sea vehicle NEPTUN along 6 profiles with common length about 300 km (Fig. 1). In total, about 11,500 digital photographs (what cover approximately 40,000 m2 of the ocean floor) were analyzed for assessment of nodule coverage and investigation of megafauna (animals, visible in photographs, the dimension more than 2 cm). The giant single-cell organisms Xenophyophorida were the most multiple animals in seabed photographs. Their number on the site area averaged 1187 ind/ha. However, the vertical camera position does not allow counting all xenophyophorids, therefore their valid number is represented 10 times more. According to all available information these protozoans play the relevant role in assemblage of deep-water environment, giving for other animal groups an [ ] additional source of nutrition and a substratum for settlement and attachment. The ophiuroids are found in assemblage with xenophyophorids in many cases, standing on a sediment at their base.

Jan 1, 2010

By Kioshi Mishiro, Pratima Jauhari, Walter Williams

INTRODUCTION The UN-General Assembly adopted an Agreement on 28 July 1994 entitled ‘Agreement relating to the implementation of Part XI of the United Nations Convention on the Law of the Sea ((UNCLOS) of 10 December 1982’. The Agreement came into force on 16 November 1994, and consequently, the inauguration of the International Seabed Authority (ISA, or the Authority), located in Kingston, Jamaica. The Authority is the organization through which States Parties to the Convention (168, as of 25 July 2017) shall, in accordance with the regime for the seabed and ocean floor and subsoil thereof beyond the limits of national jurisdiction (the Area) established in Part XI and the Agreement, organize and control activities in the Area, particularly with a view to administering the mineral resources of the Area. The legal regime for the administration and development of the mineral resources of the Area as it now exists are available in Part XI of the Convention1 which contains the legal framework governing “activities in the Area” and in Annex III to the Convention which contains the “Basic Conditions of Prospecting, Exploration and Exploitation” with respect to the resources of the Area2. The 1994 Agreement relating to the Implementation of Part XI of the UNCLOS is the so- called ‘parallel system’; as elaborated in article 153 of the Convention. The essential elements of the ‘parallel system’ include assured access for States parties and their nationals to seabed mineral resources along with a system of site-banking, whereby ‘reserved areas’ are set aside for the conduct of activities by the Authority through the ‘Enterprise’ itself or in association with developing States or in joint venture with the contractor who provided the particular reserved site2.

Jan 1, 2018

By Isobel Yeo, Florent Szitkar, Sven Petersen, Sebastian Graber, Meike Klischies

Technological advances and the shift towards green energies in the last decades have led to a substantial increase in the demand for metal resources. With rising political tension, and quasi-monopolistic production of some key metals, a secured supply chain cannot be guaranteed [1]. Therefore, the focus of the international research community and mining companies has expanded to the seafloor, looking for additional resources. The seafloor may have the potential to contribute significantly to a secure metal supply in the future. However, we have only investigated a fraction of our oceans in sufficient detail to assess the global resource potential. A detailed exploration of the vast seafloor is currently economically not feasible, due to its extremely time-consuming and costly nature. Seafloor massive sulfides generally form along the active plate boundaries and at active volcanoes in arc settings. However, the resources are not evenly distributed on the seafloor. Large deposits tend to be more common along slow-spreading and ultra-slow- spreading ridges that make up the majority of the global mid-ocean ridge system [2]. Therefore, it is important to establish geological models and exploration criteria in order to narrow down the permissive areas, which are likely to accommodate economically interesting deposits. Based on a detailed study of the TAG hydrothermal field in the central Atlantic Ocean, hosting a large active mound as well as several inactive mounds, we develop exploration methods and criteria to define areas of potential massive sulfide occurrences along slow-spreading sections.

Jan 1, 2018

The Brothers hydrothermal system is host to two very contrasting vent fields and to date, is the only known example of this kind for any submarine arc volcano in the world. Firstly, there is the NW caldera field. It is perched on the caldera walls and is up to 1,200 years old, and represents a more ?mature? system dominated by water/rock interactions, though there is also evidence for magmatic contributions to the hydrothermal fluids. It is host to relatively high temperature (~300°C), focused venting of metal-rich fluids. Large Cu- and Zn-rich sulfide chimneys occur at this site, with high concentrations (up to 90 ppm) Au apparent in some chimneys. Vent fluids of the NW caldera site show sub-seafloor phase separation is occurring at this site. Silica concentrations in these vent fluids are consistent with the vent fluid temperatures. Secondly, there is the cone vent field that is much younger, and which sits atop the summits of a main cone (the Upper cone) and an adjacent satellite cone (the Lower cone) that occur inside the caldera, near the southern caldera walls. This field is dominated by S-rich vents with vent fluids more diffuse, lower in temperature (<120°C), very gassy and acidic (to pH 1.9), and relatively metal-poor. Fluids of the cone site have Mg and SO4 concentrations higher than seawater values, indicating these ions have been added to the hydrothermal fluid and are not being depleted via normal water/rock interactions. Variability occurs between the two cone vent fields, with the diffuse discharge observed at the Upper cone volumetrically small and chemically different from the Lower cone. For example, from the vent fluid Mn, Li, Rb, and Cs concentrations, it is apparent that the Lower cone has experienced a lower degree of water/rock interaction (i.e., more reaction) than the Upper cone. Vent fluid pH is higher for Lower cone, consistent with more reaction and neutralization of acidic gases. Fe/Mn is lower at the Lower cone due to decreased Fe solubility at the higher pH. The lowest pH sample (1.9) is from the Upper cone that has 39.4 mmol/kg of SO4, consistent with input of magmatic SO2 and disproportionation to sulfuric acid and S or H2S. Thus, the Upper cone site could be interpreted to have a shorter reaction path and residence time between the point of magmatic degassing and the seafloor venting than the Lower cone site. Isotopic compositions of the NW caldera and cone vent fluids show evidence for magmatic water with negative dD and d180 values, while 3He/4He values show the Brothers hydrothermal system has shifted towards more magmatic conditions over the past several years with both sites affected by magmatic events. Similarly, vent fluid sulfide d34S values and those for sulfide minerals from NE caldera chimneys also indicate disproportionation reactions involving magmatic SO2. Minerals such as chalcopyrite, bornite, chalcocite, covelllite and euhedral grains of hematite occurring in high temperature chimneys from the NW caldera site are consistent with a more oxidizing, magmatic fluid, while bulk sulfide geochemistry data show evidence for a higher temperature suite of elements (e,g., Mo, Co, Se) associated with Cu-rich chimneys. Gold mineralization occurs in these high temperature chimneys and is associated with the most recent deposition of high concentrations of Cu, where d34S values are most negative. Geophysical evidence suggests that the top of a magma chamber occurs ~2.5 km below the caldera floor, beneath the cone site in the SSE quadrant of the volcano. Very low velocities of <1 km-2 are seen in the seismic data between the magma and the seafloor, and are indicative of gas release. Harmonic tremor data provide evidence for a 500 m pipe-like ?conduit? located above the magma chamber (and below the cone), linking it with the overlying hydrothermal system, providing a mechanism for magma-derived metals to enter the hydrothermal system under the cone site. The NW caldera and cone sites are considered to represent stages along a continuum between magmatic-hydrothermal and water/rock-dominated end-members.

Jan 1, 2010