Search Documents

By J. Nakayama

For installation of round steel piles or cast-in-place pile construction through boulder contained ground or rocky formation, usual system does not function properly or impossible to work. This paper introduces an installation system which combines unique mechanism where the drill is installed on the top of a driving round steel pile or a stand pipe which is initially driven into the overburden to the depth of self-standing. When the pile driving or bore hole drilling encounters hard strata or boulder contained ground, hard material shall be crushed by the down-the-hole chiselling operated in adjustable short stroke and high frequency of blows while cuttings are discharged in reverse circulation through central reverse pipe while round steel pile is simultaneously stroked by a hydraulic hammer. The paper shall explain the mechanism of the system and introduces construction examples for bridge foundation and piled jetty.

Jan 1, 1999

By Pastsakom Kitiyodom

In order to estimate the deformation and load distribution of a single pile subjected to dynamic horizontal load as well as vertical load, a simplified method of three-dimensional numerical analysis, KWaveHybrid program, is developed using a hybrid model. In the hybrid model, the pile is modelled as elastic beams, and the soil at each pile node is treated as springs and dashpots in both vertical and horizontal directions. KWaveHybrid is also able to analyse the static response of the pile. Validity of the newly developed program is examined through comparisons with theoretical values and horizontal dynamic and static pile load test results

Jan 1, 2006

By R. D. Short

Environmental regulations for noise and air pollution are directly affecting the type of equipment and construction techniques being utilized for pile driving construction using diesel hammers in California and elsewhere. Consequently, the cost of construction is increasing and in some cases, the use of diesel pile hammers has been prohibited. Based on the trend in California and elsewhere in the world, environmental constraints are spreading and becoming more restrictive. The City of Tokyo, Japan, for example has banned the use of diesel hammers. Environmental restrictions on diesel hammers can be satisfied by using modern hammers, clean burning fuels, synthetic lubricants and pre-excavation techniques.

Jan 1, 1989

By Deshmukh A. M.

Existence of human beings and their relationship with the nature is symbiotic. The lack of perspective and negligence of nature disturbs the equilibrium of environment and causes unprecedented disasters. Geotechnical engineers are directly concerned with hazards of nature as elements of foundation and of nature are inter related. Rational design and construction of foundation can be accomplished only after properly assessing influence of environment This paper briefly delineates impacts of environment and human activities and presents salient features of management of impacts through the system of deep foundation. Limitation of negative effects and enhancement of positive developments necessitates eco-consistent planning of engineering projects based on the geotechnical aspects of environmental impact management.

Jan 1, 1996

By Karl A. Higgins

In 1976, Prof. G. G. Meyerhof published a famous article in the Journal of Geotechnical Engineering titled ?Bearing Capacity and Settlement of Pile Foundations?. This article presents the authors opinions on calculating pile capacities in clays and sands, group capacities and pile settlement. A portion of the article presents correlations of shaft friction and end bearing to the Standard Penetration Test (SPT) N-value. Subsurface exploration via the Standard Penetration Test is the most widely used exploration tool in the United States, so correlations of pile capacity to N-value are significant to the practice of geotechnical engineering. Meyerhof?s SPT-N correlations are relatively simple calculations compared to other pile capacity computation methods presented in the article or found in other text books (such as the a-method, b-method, Nordlund, Vesic, Meyerhof?s semi-empirical, others) and therefore are popular amongst practicing geotechnical engineers. At the time these correlations were published by Prof. Meyerhof, utilization of dynamic testing with the Pile Driving Analyzer (PDA) was not widespread in geotechnical engineering practice. Prof. Meyerhof?s correlations appear to be based upon conventional static pile load testing of instrumented piles. Dynamic pile measurements to estimate a pile?s static capacity provides certain advantages over conventional static load testing, namely the determination of unit shaft friction values at discrete intervals along the pile, and the unit end bearing support value. The author has compiled a database of driven, displacement piles tested with dynamic methods (ref. ASTM D4945, Test Method for High-Strain Dynamic Testing of Piles). The data was collected between 2002-2010 and is comprised of displacement piles driven into coastal plain sediments in the mid-Atlantic states of Virginia, Maryland and the District of Columbia. In layered soils, dynamic testing in particularly helpful as it reveals the differences in unit shaft friction for varying soil types. One hundred ninety (190) piles are included in the database, with a corresponding 1,373 discrete shaft friction and 190 end (toe) bearing measurements. The pile type typically consisted of 12 and 14 inch square, prestressed, precast concrete piles; however, a significant number of piles were steel HP 12 or 14 inch sections. The database was sorted based upon soil type, and then correlations of shaft friction and end bearing were derived in the same or similar manner as Meyerhof?s original 1976 publication. The new correlations are compared to Meyerhof?s original values.

Jan 1, 2011

By Jom Gentry

Acrylamide chemical grout (C3H2NO) has been successfully used for over 50 years to control groundwater and stop infiltration. This paper will address three unique projects involving the control of groundwater with each study providing special circumstances and geological conditions: encapsulation of radioactive hazardous waste in the United States, a tailings dam for a large copper/gold mine in Argentina and 27 miles of leaking subway in Canada. The primary reasons for selecting acrylamide grout were based on the following characteristics: thinnest chemical grout on the market, a true solution grout which contains no suspended solids in the blended product, flexible gel set times, and a 362 year half-life in soil as determined by the U.S. Department of Energy.

By S. Narasimha Rao

Bored cast in situ piles are highly susceptible to construction defects like necking, discontinuity in concreting, poor compaction of concrete, improper end bearing condition due to inadequate cleaning of bore hole, exposure of reinforcement, segregation of concrete etc. There is a necessity to understand the behavior of piles so as to design effective foundation system. In this paper investigations of two field cases were discussed to bring out the effect of defective piles. In one case improper end bearing has been discussed for a concrete pile of length of 45m and diameter equal to 1.2 m and is reinforced with 32 no's of 28mm diameter steel bars and in another case necking of the pile has been discussed. Further model piles with preformed defects have been tested in laboratory to bring out the influence of defective piles.

Jan 1, 1996

By Michael P. Balducci

Urban deep foundation projects contain unique risks that must be recognized by the parties involved. Common pitfalls must be recognized and avoided or addressed through contractual relations and corresponding insurance coverage. By understanding these pitfalls, examining the risk-apportioning clauses and corresponding insurance obligations, may the parties? desires and expectations be met.

Jan 1, 2008

By Derek Egan

"Abstract Construction clients want their foundation solutions to be right first time, every time; but it is often the geotechnical contractor who carries the most risk in achieving this. Robust validation to ensure that the installed geotechnical product is appropriate for the encountered ground conditions, will perform as required and be correctly measured for payment and record purposes is very important to minimise the contractor’s and the client’s risk. This paper outlines the development and operation of a robust real-time installation monitoring system which controls and validates the installation of driven cast in-situ (DCIS) piling. Using state of the art information technology the system allows the design engineer to interrogate the data acquired from the piling rig via his computer as the piles are completed. The use of the validation process, where data acquired during the driving of DCIS piles can be processed to estimate the finished pile performance, will be explained with reference to a new case study on large diameter DCIS piles. Examples of the routine use of the system will be presented to illustrate how automated monitoring of installation parameters can be used to raise the standard of reliability, efficiency and sustainability on piling projects. The conclusions to the paper will cover the key features and operational challenges characterising real-time monitoring of the execution of geotechnical works as developed from a number of years of experience of using a rig based data acquisition instrumentation system.INTRODUCTIONDriven Cast In-Situ (DCIS) piles have a long and successful history of use worldwide. The process, where a temporary steel drive tube, sealed at the bottom with a sacrificial base plate, is driven into the ground and filled with concrete before the tube is withdrawn, is well known (BS EN 12699, 2001 and Egan, 2013). Examples of large structures supported on DCIS piles installed by Keller UK include the Millennium Dome (now the O2 Arena) and the 2012 Olympic stadium in London.In recent times advances in piling rig instrumentation and telecommunications have enabled a new level of sophistication in the recording of installation parameters and the validation of pile performance. It is now possible to embed these features into the DCIS design and installation process which has improved the quality and efficiency of DCIS piling.This paper summarises the development and operation of a real time data acquisition and processing system for DCIS piling, but which is equally applicable to other forms of driven piling (for example concrete precast piling)."

Jan 1, 2014

By A. J. Partos

The figures and tables referred to herein are presented in the Proceedings; Volume I, Pages 309 through 316. The 61-story One Liberty Place, at 315 m., is the tallest building 1n Philadelphia and was in 1987 the ninth tallest building in the world. One Liberty Place is supported on drilled piers socketed in heterogeneous metamorphic rock. Design load distribution was 40% on the base and 60% by shaft resistance. Drilled Pier G-10 supporting a T13-A type outrigger column was instrumented. There 1s no uplift load on the exterior outrigger columns. This column supports a 53,850 kN compressive load which includes a 13,440 kN windload. Table 4 presents experimental parameters from straight line interpolation of Mohr failure envelopes for the Wissahickon schist. Lowest values of cohesion (12,200 kN/m2) and angle of internal friction (19°) are at a 50° - 59° angle of foliation. Figure 3 presents a typical pier supported by shaft resistance 1n decomposed (D) and coreable (C) rock and by end bearing (B).

Jan 1, 1991

By Evelio N. Horta

The influence of soil improvement replacement area in foundation settlements is discussed for soil improvement methods used in Southeast Florida. A 3D Finite element analysis is used for two typical conditions in the area: foundations bearing on loose sands and foundations bearing on a crust of limestone underlaid by very loose sands. Particular attention is given to Jet Grouting as a soil improvement method. The potential impact of the stiffer jet grout columns on the structural foundation design and quality control issues are also discussed. It is shown that in loose sand conditions 15 to 20% area replacement produces substantial reduction in total settlements. Reduction in total settlements for mixed profile is less significant but the use of the method in those cases is directed to reduce punch through potential.

Jan 1, 2007

By Wen-Chieh Cheng

Two bored piles with base grouting are loaded axially and the results are used to compare with numerical analyses. One compressive pile with a diameter of 2 meters is drilled through clay deposit and into bedrock to a depth of 13.7 meters. One tensile pile with a diameter of 1.5 meters is drilled through the same clay deposit and into bedrock to a depth of 17 meters. Both piles are installed with monitoring system such as rebar strain meters, concrete strain gauges and extensometers. The monitored data during pile load test are used to obtain average frictional stress (t) a displacement (z) curve, pile tip bearing (q) as well as pile head load (p) and a displacement (s) curve. FLAC3D is used to simulate the pile loading and base grouting. The soil and bedrock are modeled with Mohr-Coulomb. The parameters of the constitutive law are established from soil biaxial tests and rock bore hole deformation tests. The pile is assumed as an elastic body. The interface element is used to simulate the pile/soil interface and pile/rock interface. The numerical results are compared with the pile load test in terms of t-z curve, q-z curve and p-s curve. Finally, the pile base grouting is simulated and the uplift is analyzed. The result from this study is promising and the numerical modeling is successful.

Jan 1, 2006

By J. X. Wu

An investigation on the seismic damage to buildings with pile foundations in Tianjin region, was conducted after the earthquake which hit Tangshan in 1976. It showed that most pile-founded buildings have an excellent aseismic capacity. In this paper, several pile-founded projects suffering the seismic damage are introduced as examples, simplified calculations are made of the vertical bearing capacity of pile foundations and of the horizontal seismic force, and suggestions are presented in conection with the design of pile foundations in the liquified ground soil. The paper shows a frame structure which has a plie foundation with a box-shaped base. Analyses if its response to the earthquake has been carried out in accordance with the F.E.M. and results have been obtained.

Jan 1, 2010

By Marius B. Wechsler

There are considered deep piles which are fixed in blocks of rotating machinery foundations. A mathematical background is developed for determining the behavior of this kind of piles for motions caused by horizontal and vertical oscillations, as well as by roc-king and twisting. It is assumed that the piles come across a top soil layer of depth c, not capable of lateral support, and penetrate over a length b, in a bottom firm soil layer, or in a bottom soft soil layer in which vibrations can produce voids around the piles. With respect to b and c, as well as to the elastic properties of piles and soils, the analysis leads to the maximum bending moments and shear forces subjecting the piles, to the maximum lateral bearing on the bottom soil layer, as well as to the deflection of the pile and the displacement of the foundation block. The results of the performed analysis can be applied to seismic loads too, and they are illustrated by a numerical example.

Jan 1, 1987

By Roy Jennings

The Discovery Expedition of St. Charles, MO chose to build its two-story museum in the flood plain of the Missouri River, near the starting point of the Lewis and Clark Expedition. Should the lower level be inundated at flood stage, plans call for the replica riverboats to be moved by trailer to higher ground. The museum's design required an open span structure with heavily loaded footing or piles. Spread footings could not be used due to the compressible soil profile. The location, in a historical district, precluded dynamically driven piles. Sixty-three uncased Helical Pulldown Micropiles were driven to the bearing stratum to support the museum with minimum disturbance. There were no spoils to dispose of during construction and the piles were completed in eight working days with minimum impact to the environment and neighborhood. The maximum working load required was 84,000 pounds (374kN). Test results are given in the form of installing torque.

Jan 1, 2003

By D. R. Dance

The Resonant, or as it has more commonly come to be known the 'Sonic' Pile Driver, dates back to the early 1960's, when prototypes were produced by Charlie Guild, of Providence, Rhode Island, and A1 Bodine of Los Angeles, California, these were later to be developed into the unit known as the BRD 1000. Based on this initial work, the Shell Oil Companies of Sonico and The Resonant Pile Corporation, produced and operated 30 of these BRD 1000 machines, which were used throughout the U.S.A. and Canada on a wide range of foundation projects. Subsequent to this, Raymond International and G K N, of England, operated units on programs; the G K N units being of slightly modified configuration. In 1973 Hawker Siddeley Canada Ltd., acquired the license for the Pile Driver and related systems with the intent of promoting the use of the machines to install support pilings on the Alyaska Pipeline Project, but this did not materialize due to problems with the oscillator. After radical redesign and field testing of the oscillator system the unit was employed on a number of test projects principally in Northern Canada and Alaska.

Jan 1, 1987

By J. Matos e Silva

"Abstract The paper refers five examples of executed diaphragm walls with one to five levels of anchorages. For each example a comparison is made between the results of the design using the traditional criteria and the ones obtained by using the Eurocode 7 and the Portuguese Norm related to the EC7 (NP EN 1997-1 2010), as the Eurocodes consider the possibility of each European country to adopt their own geotechnical parameters as these may vary from one country to another. A comparison is also made with the behaviour of these diaphragm walls during its construction phase; so the values from the design that were adopted in the construction are listed in tables 2 to 6 in the “Construction Options” columns. From the referred examples the author presents his conclusions.1 - INTRODUCTIONIn the so-called “traditional criteria” the soil parameters (dry unit weight, angle of internal friction and cohesion) have values obtained through tests or empirically. It is assumed that the characteristic values of the soil parameters adopted in Eurocode 7 are equal to the soil parameters adopted in the calculations by the “traditional criteria”. In the present paper the design according to the EC7 was made considering only the ultimate limit states and the respective Cases A1 and A2.The partial coefficients used for the actions in the present paper were those on Table 1:2 - CONSIDERED EXAMPLESThe five examples correspond to the situations of figures 1 to 5, and the respective results are summarized in tables 2 to 6.For all the considered examples, that are case histories, a simplified method published by Matos e Silva (March 2000) was adopted. This method attains good performances when compared with other more sophisticated ones as the finite elements and the elasto-plastic methods as described in a paper published by Matos e Silva (2000). All the obtained values were compared between them and with the so-called “Construction Options” that were the values adopted by the designers of the considered examples. For the wall bottom length calculation two possible situations were envisaged:"

Jan 1, 2014

By F. Castelli

A simplified non-linear method to predict the behaviour of a single pile and/or pile group under horizontal loads is presented in the paper. The evaluation of the non-linear lateral deflection is based on a procedure taking into account the decrease of the model stiffness with the increasing of the applied load. The solution derived firstly for the single pile, was extended to the case of a pile group introducing the p-multiplier (fm) concept proposed by Brown et al. (1988).

Jan 1, 2006

By Li Tiemin

It is one of important tasks in research of vibratory pile driving to increase speed of pile driving and depth of pile driving -- this means to increase capability of penetrating hard layer. In general, vibratory pile driving hammer make pile be situated in vibratory situation to drive pile by means of weight of hammer and pile, but the depth of pile driving and capability of penetrating layer are limited by dead weight of hammer. This paper introduces a new kind of vibratory pile driving hammer which differs from general ham­mer. A set of pressing system is attached to hammer and pile driving frame. The pull of winch installed on frame passing guide pulleys bring downwards press to pile through absorbing system of hammer. The practice and comparison test have showed that the new hammer is faster in pile driving and bigger in capability of penetrating layer than general one. Now, the vibratory pile driving hammer with pressing device has been applied widely in China. RESUME: The vibratory pile driving hammer based on vibratory principle to design have applied wide­ly in foundation engineering in many countries over the world. In order to suit the needs of deep foundation, at present, how can quicken speed of pile driving and increase depth of pile driving have become even more value to many countries in the world. This paper introduces a kind of rapid vibratory pile driving hammer which can drive pile deeper and more faster comparing with common vibratory pile driving hammer. Therefore, a kind of simple and reliable method has been offered for rapid vibratory pile driving in deep foundation.

Jan 1, 1991

Jan 1, 1993