Search Documents

By Josef K. Alter

Crosshole Sonic Logging (CSL) of drilled shafts requires 1.5-in (38-mm) or 2-in (51-mm) I.D. sonic access tubes to be installed inside the steel reinforcement cage. The sonic access tubes do not contribute to the structural capacity of the drilled shaft. The proposed use of Ischebeck TITAN T73/56 CSL/Hollow Threaded Rebar for Cross Hole Sonic Logging Access Tubes Combined with Longitudinal Concrete Reinforcing in Drilled Shafts (patent pending) is discussed as an alternative method of construction and CSL probe access. The T73/56 hollow threaded rebar/sonic access tube performs as a high strength rebar while at the same time creating a 2.2-in (56-mm) I.D. sonic access tube. The deformed high strength hollow bar provides better adhesion to concrete thus reducing the problem of debonding associated with smooth PVC and steel pipe. A cost comparison using conventional rebar with added sonic access tubes is discussed. The use of T73/56 CSL/Hollow Threaded Rebar as a value engineering alternative can reduce both material and labor costs for drilled shaft construction and can provide an advantage where anchor bolt cages and longitudinal reinforcing create congestion.

Jan 1, 2011

By Alessandro Bertero, Dylan Pearson, Wesley Schmutzler, Matteo Bertoni

"The SR 83/US 331 highway is located in the Florida panhandle, where it connects the Walton County beaches to the I-10 corridor. The roadway is of vital importance to the economy of the area as well as its safety since it represents the primary hurricane evacuation route from southern Walton County. The Florida Department of Transportation (FDOT) decided to increase the number of traffic lanes from two to four and improve the geotechnical properties of the moderately deep, very loose foundation soils, that had affected the highway rideability for years. The soil mixing was selected as the method to meet the unique deep ground improvement challenges of the project. The design required that Shallow Mixing Method (SMM) be used to build a 10-foot thick platform that transferred axial load to the bottom soil layers through a series of Deep Mixing Method (DMM) columns. Upon completion over 8,300 SMM columns and 1,500 DMM columns had been installed, with no remedial work required. Also, only 1% of the almost 1,500 specimens tested did not meet the specification requirements. This paper will describe the challenges encountered and provide valuable information that may be useful for other future projects, including details not previously published.INTRODUCTIONThe counties of Walton and Okaloosa have been a very popular vacation destination for many ears. The 50-mile long coastline boasts beautiful, sugar-white beaches and waters the color of emeralds. The popularity of the area has been growing even further, over the last few years. A consequence of this phenomenon is a fast-paced increase of the traffic flow on the SR83/US331 highway, especially at the bridge that connects the Walton County beaches across Choctawhatchee Bay (Fig. 1) to the heavily traveled I-10 corridor. The highway plays a very important role for the area also as a commercial link and as the primary hurricane evacuation route from southern Walton County. The increase in traffic has produced higher travel time, when not a complete traffic paralysis, and exacerbated the issue of ground settlement where accelerated wearing of road foundation occurred due to the presence of very loose, moderately deep, soils, that had afflicted the highway for several years. The Florida Department of Transportation (FDOT) decided to put an end to these issues by increasing the number of traffic lanes from two to four and improving the geotechnical properties of the foundation soils. The Design-Build Maximum Price Request for Proposal (RFP) issued for the expansion of the Choctawhatchee Bay Bridge saw the participation of numerous D/B teams which produced various technical solutions. Among them, the FDOT selected the Skanska/Parsons Brinckerhoff (General Contractor) proposal which provided for the use of soil mixing as the ground improvement technology. The design/build team assigned Foundation & Geotechnical Engineering (Designer of Record) the ground improvement design which Treviicos South (Specialty Contractor) would execute."

Jan 1, 2017

By Minna Karstunen, Patrick Becker

"Abstract The deformation behaviour of a foundation on deep mixed columns in a natural soft soil is a three-dimensional problem, which has to be considered adequately in numerical modelling. However, simplifications are often made due to the computational costs of fully coupled 3D analyses by either modifying geometry of the problem or material parameters in 2D for plain strain analyses or by modelling the problem as 2D axisymmetric case. The volume averaging technique (VAT) is an enhanced 2D FE technique that enables mapping the 3D problem in two-dimensions, yet modelling the two constituents (column and soft soil) with appropriate different constitutive models within a homogenized material. The performance of the volume averaging technique is demonstrated by considering unit cell simulations of floating and end bearing columns in soft soil. The results with VAT are compared and validated against conventional 2D axisymmetric and fully coupled 3D finite element analyses.IntroductionThe properties of very soft clays, silts and organic soils can be improved by stabilizing agents, such as lime and/or cement that are mixed into the soil in situ by using auger-type mixing tools in situ. Deep mixed columns are extensively used to reduce deformations and to improve the overall stability of embankments and foundations on soft soils. Whilst the most typical applications are embankments, increasingly the method is used under foundations. The first category of applications is very common in Scandinavian countries, whilst the latter application has been pioneered in Poland, as an environmentally friendly (low CO2) and cost effective alternative for piling. Due to economic and environmental reasons there is an increasing interest in the technique elsewhere in Europe. With deep mixing, the strength and deformation properties of the soft soil can be improved, and the risk of unwanted deformations is substantially reduced.Numerical methods, such as finite element (FE) analysis, can be used as an alternative to conventional design methods. They are particularly suitable when considering serviceability limit state, i.e. deformation analyses under working loads. FE analyses allow using advanced constitutive models that take account of the complex stress-strain behaviour of natural soil and stabilized columns, respectively. The problems that involve a grid of circular columns under an embankment or a strip footing are fully three-dimensional problems. As 3D analyses are very laborious and expensive, an enhanced 2D technique using the so-called volume averaging technique (VAT) is utilised. The basic idea is to describe the column-improved ground as a homogenized composite material, and using clever mathematics to map the true 3D problem into 2D. Once the constitutive relations of both composites are defined, the response of the column-improved ground can be simulated in 2D subject to arbitrary loading and boundary conditions."

Jan 1, 2014

By Ken Andromalos

Continued population growth combined with limited water resources in the Denver area has resulted in the conversion of a number of mined out gravel pits in the area into municipal water storage facilities. The use of slurry walls provides a cost effective means of isolating groundwater to convert these pits into efficient water storage facilities. Design considerations include: stability, underlying bedrock conditions, backfill mix design and earthwork requirements. Installation issues during construction include: trench stability considerations when excavating through relatively clean sand and gravel deposits in potentially high groundwater conditions; keying into three to ten feet of fractured claystone, siltstone or sandstone that makes up part of the Denver formation, and quality assurance procedures to assure a proper groundwater barrier is constructed. The paper concludes with two brief case histories to illustrate how these considerations are applied

Jan 1, 2007

By Matteo Montesi

Deep foundation elements are often used as discrete elements in externally supported earth retaining structures such as soldier piles and lagging walls, secant/tangent pile walls, anchored walls, etc. These structures can be designed using different approaches such as conventional limit equilibrium methods, finite element/difference analyses, and soil spring (p-y) analyses which are contained in various commercially available computer programs used by engineers worldwide. Although these programs usually undergo various degree of verification and validation, users must be aware of each program’s limitations and conditions in which each design approach should or should not be used. These programs may incur difficulties when non-continuous deep foundation elements are used as part of the retaining system and in cases of non-uniform geometry where closed-form solutions are not available. Design input parameters such as passive arching width, wall-to-soil friction, and p-multipliers (pm) are not always given enough attention which may result in potential design deficiencies. This paper presents the main features of various earth retaining structure design approaches and discusses their advantages/disadvantages. The paper addresses some of the limitations and difficulties that may be faced with when utilizing non-continuous discrete deep foundation elements and identifies key elements that are sources of potential deficiencies and errors. An example comparing the design outcomes using different design approaches is presented. INTRODUCTION Earth retaining structures are used to retain soil and create or maintain a difference in ground elevation between grades in front and behind the retaining structure. Deep foundation elements have been used for decades to support earth retaining structures. Earth retaining structures that are supported by deep foundation elements are typically referred to as externally stabilized system (O’Rourke and Jones, 1990). An externally stabilized system uses an external structural element, in contrast to internally stabilized systems which rely on reinforcements installed within and extending beyond the potential failure mass. The design of externally supported retaining structures can be accomplished using different approaches, which can be challenging under certain conditions. Each approach has been discussed extensively in available literature, and is well summarized in the and Federal Highway Administration (FHWA) guidelines. The objective of this paper is to present the most widely used design approaches and discuss their limitations and difficulties in one concise and brief document, giving the reader a good source for comprehensive understanding of the various design approaches, supported by a technical example. This paper is not intended to be a comprehensive review of all available design methods and formulations available in the literature.

Jan 1, 2018

By Giovanni A. Bonita

The United States Capitol Visitor Center (USCVC) is one of the largest underground structures ever constructed in the Washington, DC, metropolitan area. The 600,000 ft2 (55,750 m2) structure is entirely underground and immediately adjacent to the shallow foundations of the existing U.S. Capitol building. Interior building columns for the USCVC were supported on 186 drilled shafts that varied in diameter from 4 to 9 ft (1.2 to 2.9 m) and in length from 15 to 45 ft (4.6 to 13.7 m). The vast majority of the building utilities were located beneath the basement floor slab. It was decided at the onset of the project to proceed with construction prior to completion of the design drawings, and coordination between the underslab utilities and the drilled shafts had not yet been finalized at the onset of drilled shaft installation. Given depth and location restrictions of the outlets, relocation of the bulk of the utilities was not possible. Almost half of the drilled shafts were affected, leaving redesign as the most feasible remedial solution. The redesign involved adjustments to the shaft length, diameter, and bell. It took place on a case-by-case basis, sometimes only minutes before installation began. Coordination between the field and design team was excellent, and delay associated with the redesign efforts was minimal. In addition, the detailed, high-quality field records kept by both the contractor and field engineers allowed for accurate and fair estimations of the added drilled footage and concrete volumes placed. The additional service fee, which was minimal, was settled quick and fair.

Jan 1, 2006

By Robert Bittner

The following is a report on the development of two unique and separate cofferdam systems used in the construction of the marine foundations for the I-205 Columbia River Bridge at Portland, Oregon for the Oregon Department of Transportation. The first of these two systems utilized interlocking H-pile 100 ft long to form a cofferdam 145 ft by 58 ft in plan and 100 ft deep. The second system consisted of two immense bell shaped steel forms. The larger of the two forms was 83 ft by 66 ft in plan, 62 ft high and weighed 450 tons. This form was externally stiffened for a designed hydrostatic head of 54 ft. Both forms were designed, except for the top 14 ft, to be set and stripped in one solidly welded unit. The supporting geological formation for the bridge foundations is the Troutdale, a cemented sand and gravel. This formation is at the ground surface on the Washington Shore and slopes downward to a depth of 115 ft below normal high water at about mid-channel. In this area the Troutdale formation is covered with a layer of fine to medium sand 90 to 100 ft thick. It was the variable depth of the Troutdale which determined the two types of foundations and the corresponding to the two cofferdam systems.

Jan 1, 2013

By Wendy L. Mathieson

The Bonneville Power Administration (BPA) will build about 500 miles of new 500-kV transmission lines in the next 5 years. Many new lattice towers will be built in remote locations or in environmentally sensitive areas. Therefore, micropile foundations were designed that could be installed in remote areas, in variable subsurface conditions, and in a manner that would reduce excavation volumes and potential erosion concerns. Typical lattice tower foundation axial loads range between 75 and 1,500 kips (300 to 6,700 kilonewtons [kN]) per leg, with uplift loads being slightly less than compressive loads. Lateral loads range from 5 to 320 kips (20 to 1,400 kN) per leg. Full-scale axial and lateral load tests were conducted in geologically representative soil units during the micropile design for the 9-mile-long (14-kilometer [km]), Kangley-Echo Lake transmission line that extends through a protected watershed east of Seattle, Washington. Micropile foundations for single and double circuit suspension and dead end towers were designed using these load test data.

Jan 1, 2004

By Larry Rayburn

Design of cost effective engineered solutions to complex problems requires the team efforts of the owner, the designer and the specialty construction contractor. The basic ingredients of success required to remain competitive and still produce a quality product are creative design based on experience and sound engineering principles, plus practical aspects of constructibility. The three case histories describe creative design/construct approaches that benefited all parties. 1. Introduction The increasing demand placed on specialty contractors to provide cost effective buildable solutions to complex construction problems compels us in the industry to be highly innovative. The practice of geotechnical engineering is considered more of an "art" than perhaps the other disciplines within civil engineering largely because of the basic nature and variability of soil and rock. The geotechnical design engineer must have the knowledge of the components of his design and know the limitations of his equipment and labor force. Thus, for the design/build specialty contractor the potential for creation of unusual solutions to difficult problems is quite high.

Jan 1, 1991

By Timothy D. Stark

Jet grouting has increasingly become one of the ground improvement technologies used to address seepage concerns and to provide strength improvement of soils. The technique of jet grouting uses high pressure/velocity jet fluids to erode the existing soil and then to mix the cuttings with cement slurry to form soilcrete. Excess slurry or spoil is ejected to the surface. If the native soil is not completely mixed with slurry, the resulting columns will have soil inclusions which can reduce the strength of the column and/or increase the permeability of the column. A jet grout test program at Tuttle Creek Dam shows that the completed large diameter columns contain perhaps 40 to 50% or more of native soil that was not broken up and mixed during the jet grout process. The test program included excavation of full-scale columns to a depth of 35 ft (10.7 m) for visual inspection and testing. Additionally, six of the columns were cut or sectioned to investigate the interior of the columns. The observed inclusions include significant amounts of both fine grained (silts and clays) and coarse grained (fine sands and sands) soils. Evidence suggests at least two explanations: (1) fine grained soils can be difficult to erode and break up into small enough particles that can be ejected to the surface, especially if at low natural water content, and (2) when large diameter columns are being excavated, the excavated roof of the cylindrical cavity may be unstable and may collapse. With this roof instability large slabs of material can break off, fall into the slurry and escape the cutting and mixing action of the rotating jets. This paper describes the Tuttle Creek Dam test program, inclusions observed in the completed columns, and suggests potential causes of the inclusions.

Jan 1, 2009

By Wu Jie Mei, Li Yao Liang, Franz-Werner Gerressen, Arthur Bi

Diaphragm walls (D-walls) are known as underground structural elements commonly used for retention systems and permanent foundation elements. In addition, they are also quite often used as deep groundwater barriers, called Cut-Off-Walls (COW). Shanghai ranks third among the most densely populated metropolises in the world. In 1990, only eight million people lived there. Today, Shanghai has about25 million inhabitants. The increasing demand to accommodate the infrastructure of growing megacities like Shanghai pushes the required depth for subway, sewage and foundation projects to the limit. Future projects will demand excavation depths of more than 100 m (328 ft) on a regular basis. Already carried out reference projects will be described and a general outlook for upcoming projects will be given. The paper also explains the installation process in general focusing on the use of trench cutter technology. INTRODUCTION D- walls are known as underground structural elements, commonly used as retention systems for excavation pits and shafts as well as permanent foundation walls or elements. It is anticipated that, with the increasing trend of utilizing more and more underground space to accommodate environmental considerations and urban/suburban development, there will be an increasing requirement for diaphragm wall usage in even more difficult conditions and with increasing depth. The trench cutter is the most important tool for performing this work. The hydraulic grab, a well-known and valuable excavation tool for d-walls reaches its limits in terms of depth and when cutting rock. Therefore the trench cutter technology will be in the focus of this paper. The trench cutter itself is a reverse circulation excavation tool. It consists of a heavy steel frame with two drive gears attached to its bottom end, which rotates in opposite direction around the horizontal axis. Cutter wheels are mounted onto the drive gears. As they rotate, the soil beneath the cutter wheels is continuously broken up, removed, mixed with the bentonite slurry in the trench and moved towards the opening of the suction box of the pump? A centrifugal pump located right above the cutter wheels conveys the slurry via a hose system up to a desanding plant. There the slurry loaded with soil and rock particles is cleaned and returned into the trench.

Jan 1, 2018

By Sastry Putcha, Vamshi Vemula, Aneesh Goly, Kumar Allady

Current dynamic testing practice to obtain pile total capacity will not yield optimum capacity due to the strain incompatibility between the side and tip resistances during driving. Superposition of end of initial drive- static tip capacity and the peak static skin capacity during beginning of restrike and adding them is the preferred method. The FDOT method determines independent pile static tip and skin capacities in real time analyzing appropriate blows from the embedded tip and top data of the Embedded Data Collectors (EDC). This data is collected through a wireless radio transmitter, receiver, and laptop software. The approach utilizes EDC tip and top data and nonlinear single degree of freedom system to satisfy force and energy equilibrium with a global genetic inversion analysis. Top impacted energy equals at pile tip as sum of Static, Damping and Inertial energy providing independent tip resistance. With EDC sensors as boundary conditions, pile is divided into desired segments and using global inversion techniques one dimensional equation is solved for independent skin friction for every blow. EDC data compared close static load test results. The EDC - FDOT method has enabled cost effective 100% testing of driven piles cost effective. INTRODUCTION Historical documentation has shown that not only driven piles have a long history of usage but also continues to advance unceasingly till today. Historians placed the first pile driving using timber piles in the 4th century BC. While modern pile driving systematically started around nineteenth century, the credit for conceiving the idea of the applicability of wave equation to driven piles goes to David Victor Isaccs of Australia. His 1931publication “Concrete Pile Driving Formulae” provides the basis for modern pile driving using stress wave theory. He felt that the dynamic formulae then in use lacked the capability of detecting integrity and hence developed stress wave theory. This work was further developed starting in 1938 by W.H. Glanville and colleagues of British Building Research Board as they developed the first solution to the wave equation. But these early efforts have really taken off only with the advent of computers. E.A.L. Smith (1960) published ‘Pile Driving Analysis with the Wave Equation’ and provided first numerical solution to the wave equation. Within few years, the FHWA funded research and in due course this effort ushered the era of externally instrumented pile driving.

Jan 1, 2018

By Dongwook Kim

Recently, load and resistance factor design (LRFD) is gradually being adopted internationally in geotechnical design due to the advantages of LRFD over the existing allowable stress design (ASD). LRFD is a more advanced design method compared to the ASD because resistance factor is calibrated based on the reliability analysis for a given target reliability index. Target reliability index changes with the importance of the structure. Typically, target reliability index of offshore foundation is less than those of onshore. The widely-used Imperial College Pile (ICP) design method is used for the calculation of pullout capacity of driven piles. The uncertainties regarding pullout capacities of driven piles are assessed using the statistical data reported in the literature. The first-order reliability method (FORM) is used to calibrate resistance factors for the pullout ultimate limit states of the driven piles for three different levels (2.5, 3.0, and 3.5) of target reliability index. The load factors used in this paper are the ones proposed in the AASHTO LRFD bridge design specifications.

Jan 1, 2010

By Ramon Varghese, A. Boominathan, Subhadeep Banerjee

Pile raft foundation system has been accepted as an economic foundation design for high rises and heavily loaded structures. Seismic response analysis of PR foundation systems involves complex pile-soil-pile interaction as well as raft-soil-pile interactions, for which simplified methods have limitations. Kinematic rocking of a pile group is known to be influenced significantly by the pile configuration. The presence of an embedded pile cap, or a raft, as in the case of a piled raft can further alter the dynamic characteristics of a pile group-soil system. In the present study, frequency dependent kinematic response factors are evaluated for piled raft foundation, using the substructuring approach based ACS SASSI program. Performance of the numerical analysis methodology is first evaluated with results from analytical and experimental studies reported in literature. The effect of pile layout on kinematic response is then studied for a piled raft in clay system based on a centrifuge shaking table test reported in literature. Kinematic response factors and horizontal impedances were determined for varying pile spacing ratios. The influence of raft has been found to increase kinematic translation by up to three times in the piled raft in clay system. Pile configuration is found to play a significant role in kinematic rocking of piled rafts. The presence of raft is observed to significantly reduce dynamic rotational stiffness coefficient in the dimensionless frequency range of 0.23 to 0.6, and increase damping coefficient after a dimensionless frequency of 0.4, for all pile configurations studied. The effect of an embedded raft is hence an important consideration while evaluating foundation input motion as well as impedances of piled raft foundations. INTRODUCTION The Piled raft foundation (PR), is a composite foundation system that facilitates load sharing between pile and raft. It is an economic foundation option for high rises and heavily loaded structures. Soil structure interaction (SSI) in PR system involves raft-soil-pile, and pile-soil-pile interactions which needs to be considered in static or dynamic SSI analysis. The effect of pile can have substantial influence on foundation input motion, for seismic analysis (Di Laora et al. 2017). Piles are observed to depress a wide spectrum of the seismic excitation (Fan et al., 1991, Di Laora & de Sanctis, 2013). Although kinematic response of pile groups have been extensively studied in the past, the influence of the presence of raft on kinematic response characteristics of pile groups has not received much attention.

Jan 1, 2018

By M. Hesham El Naggar, Osama F. E. Drbe

"Abstract: The use of micropiles has greatly increased the last twenty years, including applications involving low capacity micropile networks, seismic retrofitting, underpinning of existing foundations and high capacity foundations for new structures. This paper presents a field study of the behaviour of single hollow core micropiles in firm to stiff lean clay. Eight micropiles were installed using hollow bars (76 mm OD and 48 mm ID) with air/water flushing technique and advanced to a depth of 5.75m: six micropiles were installed using 228 mm (9 in) drill bit and two micropiles were installed using 178 mm (7 in) drill bit. All micropiles were instrumented with linear potentiometers to measure the vertical displacement of the micropile head and vibrating wire strain gauges to measure the axial strain at three points along the micropile length. Twelve full scale tests were conducted on the eight micropiles, four monotonic compression, four cyclic compression and four tension tests. Only the results of micropiles tested under monotonic compression is presented in this paper. The full scale load tests and a comparison of the performance of the micropiles with 228 mm and 178 mm drill bit are presented and discussed in terms of load-displacement curves, bond strength and tip resistance. The results showed that the proposed values of bond strength in FHWA give a conservative design of the hollow core micropiles. The micropiles constructed with 228 mm drill bit performed marginallybetter than the micropile with 178 mm drill bit in terms of the ultimate capacity.IntroductionMicropiles have been defined in a variety of ways, but can universally be classified as small diameter (less than 300mm), bored, and grouted in place piles (FHWA, 2005; Bruce et al., 1999; and Scherer et al., 1996). They can sustain axial (compression and tension) and/or lateral loads. Dr. Fernando Lizzi used micropiles in 1952 for underpinning of historic buildings damaged during World War II (Bruce D. A., 1988). Since then, micropile applications have expanded rapidly to include underpinning for existing foundations, in situ reinforcement, and seismic retrofitting and foundations for new construction. In particular, micropiles have graduated from use in low-capacity micropile networks toapplications as single high-capacity foundation.Micropiles capacity is affected by the construction technique, which involves drilling, placing reinforcement, and placing or pressurizing the grout. For example, the drilling method influences the degree of bonding between the grout and the ground, and the placement of reinforcement and the choice of grouting method have an impact on the development of the bonding. Bruce et al. (1997) showed that grout/ground bond is most affected by the grouting method. Based on the type of pressure applied during the grouting process, micropiles are classified as follows (FHWA, 2005): Type A: grout is placed under gravity pressure only using either sand-cement mortars or neat cement grout. Type B: pressures typically in the range of 0.5 MPa to 1 MPa are applied in order to inject the neat cement grout into the drilled hole while the temporary drill casing is withdrawn. Type C: involves two-step process; neat cement grout is first placed in the hole under gravity pressure head only as in type A, and prior to the hardening of this primary grout, a similar grout is then injected via a preplaced sleeved grout pipe at a pressure of at least 1 MPa. Type D: like type C, this type is a twostep process: neat cement grout is placed in the hole under gravity pressure head only (but pressure could be applied in some cases), additional grout is injected via a sleeved grout pipe at a pressure of 2 MPa to 8 MPa once the primary grout has hardened. In some cases, a packer is used inside the sleeved pipe, enabling specific horizons to be treated. Recently, Type E micropile is proposed, which involves"

Jan 1, 2014

By Frederick C. Rhyner

This paper describes the design and construction of two high-capacity rock anchors to restrain a supplementary backstay for the Bear Mountain Bridge, which is a suspension bridge spanning the Hudson River about 40 miles north of New York City. The supplementary backstay was installed to relieve a portion of the tension in the southern main cable, which had been creeping in recent years. The two new rock anchors were 1,200 kip capacity each, installed at a batter to depths of 59 feet. This paper describes the subsurface investigation, group capacity analysis, installation and load testing. The rock anchors included strain gages connected to the monitoring system for the bridge. The paper describes the long term strain gage data which shows no change in stress distribution in either anchor.

Jan 1, 2010

By M. England

Keywords: Bi-directional tests, Osterberg cell, O-cell®, static load tests, Timeset® Static load testing, where loads are applied vertically to the top of the pile and often referred to as 'top down testing', has been used for many years and has become a 'standard' test for the world of foundation engineering. The method, although well developed, cannot be used under certain circumstances, magnitude of load being a particular issue. There is a finite limit to the load capacity that can be applied with either kentledge, the use of reaction piles or anchors, and as the loads increase, the costs escalate dramatically. A novel test method seeks to overcome all the associated problems of large scale and restrictive area "top down testing", utilising static load testing techniques. The method requires the foundation element to be divided into two or more sections and these can be loaded axially as required using a portion of the foundation element as a reaction. This paper presents some recent applications and developments in the use and application of the bi-directional testing technique using the Osterberg Cell or O-cell® and outlines some of the many advantages of the system. Recent bi-directional test loads applied to bored piles have mobilised capacities of 279 MN and with flight auger piles up to 25 MN.

Jan 1, 2006

By Markus Schönit

Double rotary drilling combines continuous flight auger drilling with a casing for producing a cast-in-place pile. When producing a pile an outer casing and an auger (hollow auger) rotating inside the casing are driven into the ground in counter-rotation. The outer casing serves to support the surrounding soil and the inner auger excavates the drilling cuttings to the surface inside the casing. After reaching the projected drilling depth concrete is pumped through the hollow stem of the auger and outer casing and auger are extracted. After their complete extraction a reinforcement cage can be inserted in the fresh concrete. Compared to Kelly drilling the double rotary drilling method offers numerous advantages, including, for comparable diameter and length, shorter production times and higher accuracy (pile inclination and excess concrete) combined with increased occupational safety and lower noise emissions. Moreover, pile tests have proved that piles produced by double rotary drilling feature higher axial load-bearing capacities than comparable piles produced by Kelly drilling. This article offers an overview of the basic theoretical principles of double rotary drilling lists the required and currently available machinery and, finally, discusses the results and conclusions of a current jobsite.

Jan 1, 2011

By Kazuyuki Matsuzawa

A series of plate loading tests were carried out on a loam ground in order to investigate the influences of the plate size and the loading rate on the observed load-settlement relations. Two circular plates having diameters of 0.3 m and 1.0 m were used. Three types of loading methods were employed; 1) static cyclic maintained load test, 2) static continuous load test, and 3) rapid (dynamic) plate load test. An interpretation method called non-linear damping method was used to estimate a static load-settlement relation from the rapid plate load test signals. The derived static load-settlement relations match well with the measured results from the static load tests.

Jan 1, 2006

By Gustavo E. Armijo

This job was done in Morristown, NJ, with mono fluid system jet grouting for the construction of a new bank building. After the demolition of the existing two story structures, an excavation in loose sandy fill materials was necessary in order to reach the new structure basement level. Due to this jet grouting was selected as a medium to provide both excavation support and permanent underpinning, minimizing the adjacent building settlements. These two adjacent buildings were partially underpinned with a "gravity wall" made with 2 and 3 rows of secant vertical and inclined jet grout columns. Besides the classical jet grouting control methods, during the jet grouting execution, all the drilling and grouting parameters were recorded by a proprietary system called "Slogger". Additionally, after the jet grouting execution, an innovative result control technique was used by means of the application of the same parameter recording system. Some of the production columns were re-drilled and a comparison was made between the obtained drilling parameters and those obtained for the same age test columns. Under the referred existing conditions and in comparison with the conventional underpinning techniques, this project demonstrated that jet grouting, with proper execution and result control, can be faster than them and can maintain the building structural stability and act, at the same time, as a retention system minimizing the existing building settlements.

Jan 1, 2002