Search Documents

By Mary C. Nodine, Michael P. Walker, Paul Eggers, Donald E. Aubrecht

The CANALSIDE commercial development in Buffalo, New York serves to revitalize the former site of the Buffalo Memorial Auditorium, adjacent to Lake Erie. The Auditorium was constructed in 1940 and founded on steel H-piles driven to limestone bedrock. After decades of professional sport and entertainment events, the “Aud,” as it was locally known, was closed in 1996. It sat vacant until it was demolished in 2009, at which time plans were made to revitalize the area with shops, restaurants, and a historic replica canal. The only portion of the Aud that was left intact was a subbasement boiler room. The subbasement was renovated in 2014 and has since been used to house water and ice making equipment for the historic replica canals, which boast recreational ice skating in the winter. The subbasement floor was about 10 feet below groundwater and the Lake Erie water level. The floor consisted of an approximately 4-foot-thick layered inverted waffle slab system, with reinforced concrete grade beams and concrete infill between the grade beams. A waterproofing membrane was located near the base of the slab. There were no major seepage issues in the subbasement, so the existing waterproofing membrane was assumed to be intact and performing adequately. A four-story building housing a children’s museum was proposed to be constructed directly above the subbasement. The loads imparted by the new building would exceed the capacity of the existing piles, so it was determined that drilling micropiles through the subbasement floor would be the most practical means of supporting the new building. Drilling through the existing slab and waterproofing system was a concern due to the challenges of controlling water during construction and the importance of maintaining the integrity of the permanent waterproofing system.

Jan 1, 2018

By Willie M. NeSmith

Conventional augered, cast-in-place (ACIP) piles were introduced into the New York City area as a result of the damage to existing structures caused by pile driving operations. ACIP piles are often specified where deep foundations are to be installed adjacent to transit facilities, sensitive underground utilities or in close proximity to existing structures. However, loss-of-ground issues associated with the installation of ACIP piles have prevented the wide-scale use of these systems. Beginning in 2002, Berkel & Company Contractors, Inc. began using its augered, cast-in-place displacement (ACIPD) system in the New York City area. Like conventional ACIP piles, this system produces almost no vibration. Also, as almost no material is brought to the surface, there is no opportunity for loss of ground. This paper presents a description of Berkel's displacement pile system and a brief discussion of six projects in the New York City area that have been executed with this system over the past two years.

Jan 1, 2004

By Wei Zheng

A pulverized coal fired power plant is being built in Osceola, Arkansas, along the Mississippi River. The subsurface soil conditions consist of a certain amount of very soft clayey silt and clay underlain with a medium dense sand layer and a dense sand layer. The site has been raised four to five feet with fill material consisting of sand and gravel. Consolidation settlement due to the fill is expected to cause negative shaft resistance (downdrag) on the pile foundations. The site is located in a high seismic hazard area - the New Madrid Seismic Zone (NMSZ). The liquefaction analyses indicated that there is a high liquefaction potential in the medium dense sand layer. Load tests are needed to determine the shaft resistance and the end bearing of each soil layer for design purpose. Two types of pile foundations ? augered pressure grouted displacement pile (APGD) and partial augered pressure grouted displacement pile (P-APGD) were considered for this project. Ten pile load tests, including five compression tests and five tension tests, were performed for three different areas. Strain gauges were installed for the compression tests. The APGD and P-APGD piles were installed side by side for comparison. In addition, three additional dynamic tests were performed to supplement the information from the static load tests. Load deflection curves for the compression tests were predicted, and the failure loads were interpreted using four different methods. The shaft resistance and the end bearing were determined from the strain gauge data and were used to back calculate the ultimate capacity. The back-calculated capacities are in good agreement with the predicted failure loads; they were further verified with the tension load test results.

Jan 1, 2007

By Robert Bachus, Jamey B. Rosen

"Abstract Large scale In Situ Barrier Wall Construction projects, specifically those related to earth dams, dikes, and levees, frequently require stringent quality control measures to ensure the success of the wall. This presentation discusses the applications of Geographic Information Systems (GIS) technology to capture information from multiple data streams and provide geotechnical feedback, quality control, and project control feedback. Techniques used to geospatially analyze verticality data from secant piles and panels will be demonstrated. Examples will be presented from barrier wall installations at two sites owned by the U.S. Army Corps of Engineers (USACE): the Wolf Creek Dam in Kentucky, and Center Hill Dam in Tennessee.IntroductionDeep foundation installations require contractors to collect a substantial amount of information over the course of a project, both for internal quality control of construction progress and for demonstrating compliance with customer or owner specifications. Methods of collecting information are constantly improving, bringing with it the need for a systemic approach to managing the increasing amounts and types of data. Handling these diverse types of data presents challenges with both budget and schedule demands. This paper discusses some techniques for adding or increasing quality control in barrier wall constructions by consolidating, visualizing and analyzing data using relational database and Geographic Information Systems (GIS) technology, collectively referred to as Information Management System (IMS) development. The IMS concept is designed to facilitate the collection, transfer and processing of data and provide an easy way to remotely access and visualize construction progress.The remainder of this paper presents the needs and objectives of an IMS applied to quality control in barrier wall construction, the components and data flows involved, the capabilities and user interfaces of the systems and the benefits for the end users. Examples are presented throughout from case study projects including: a pile barrier wall applied in the rehabilitation at the Wolf Creek Dam in Kentucky (under contract to the Treviicos-Soletanche Joint Venture), and a secant pile barrier wall currently under construction in the rehabilitation of the Center Hill Dam in Tennessee (under contract to Bauer Foundations Corporation) (both owned by the Nashville District of the USACE)."

Jan 1, 2014

By Arash Khosravifar, Matt Steffan

An expansion of the City of Klamath Falls Wastewater Treatment plant required geotechnical seismic hazard evaluations and deep foundation design. The site is located on the shore of Lake Ewauna and is underlain by diatom rich lake deposits. Diatomaceous soils exhibit unique engineering properties that are not well understood. Cyclic Direct Simple Shear (CDSS) testing was performed on three undisturbed samples to evaluate cyclic and post-cyclic properties of the diatomaceous soils. Results from the CDSS testing indicated that the soils would not liquefy in the classical sense, though cyclic softening behavior was observed. The CDSS results were used to develop a Cyclic Resistance Ratio curve for the diatomaceous soil to compare with clean sand liquefaction curves. Seismic lateral pile capacities were developed using two approaches. One approach used conventional p-multipliers for liquefied soil and modified them to reflect expected excess pore pressure ratios. The other approach applied residual strength and fifty percent strain values from post-cyclic monotonic shear testing. A lateral spread hazard zone was identified along the Lake shoreline and reduced, seismic lateral pile capacities were recommended. The objective of this paper is to report the seismic design considerations for this project in a unique geologic and seismic setting. INTRODUCTION The engineering properties of diatomaceous soils have rarely been studied and the cyclic behavior under seismic loading is generally unknown. Some of the critical geotechnical uncertainties of diatomaceous behavior include potential for large consolidation settlement, influence of irrecoverable strains due to diatom particle crushing, shear strength (peak and residual), and cyclic properties. This paper presents results of cyclic shear testing, seismic evaluations and seismic lateral pile design in diatomaceous soils performed for the expansion of a waste water treatment plant in the city of Klamath Falls, Oregon, site of the largest recorded earthquake in Oregon’s history. The expansion consisted of adding six new facilities at the existing Plant including influent pump station (IPS) and headworks, aeration basin, tertiary treatment, and other buildings. The IPS/headworks and aeration basin will be founded approximately 15 feet below ground. The other buildings will be founded at grade. The existing facilities are supported by timber piles that penetrate the surficial diatomaceous soils and terminate on a hard underlying deposit. Figure 1 shows the site plan and proposed additions.

Jan 1, 2018

By Bengt H. Fellenius

THIS PAPER deals with the analysis of results from axial testing of vertical single piles, i.e. the most common field test per-formed. Despite the numerous tests which have been carried out and the many Papers which have reported on such tests and the analysis thereof, the understanding of pile test loading in current engineering practice leaves much to be de-sired. The reason for this is that the engineers have concerned themselves with mainly only one question: "Does the pile have a certain least capacity?", finding little of practical value in analysing the actual capacity and the pile-soil interaction. This Paper aims to show that engineering value can be gained from elaborating on a pile test ? during the actual testing in the Held, as well as in the analysis of the results. The first portion of the notes make use of an earlier Paper by the author (Fellenius. 1975). However, additional views and recent literature have been incorporated.

Jan 1, 1988

By Sikko Doornbos

For the extension of the Paper Mill of Parenco in Renkum, the Netherlands, the application of a pile foundation was required. The demands for this pile foundation were very explicit a vibration free and soil displacing pile systems with low allowable settlement. Another important aspect was the total amount of piles (originally over 1600 auger piles) which had to be executed within 3 months, in very difficult and unhomogeneous soil. Based upon these conditions the Tubex Grout Injection Pile was chosen to be used for this project. This system involves the drilling of a steel tube with a conical pile shoe while grout is injected at the point simultaneously, creating a mixed-in-place layer around the tube. INTRODUCTION After extensive marketing, the board of directors of Parenco, decided to a large extension of the production capacity of its paper mill by building a new production building called Paper Mill 1 or PM-1. The new PM-1 extension had to be constructed beside the existing PM-2 because of limited terrain. The site is located right between the Rhine river and Renkum, approximately 15 kilometers (10 miles) west from Arnhem (see figure 1). The construction involved the building of the PM-1 extension of approximately 250 meters (820 ft.) long by 40-60 metres wide (130-200 ft.). The main structure was to be constructed of precast concrete beams and columns.

Jan 1, 1987

By Peter O. Wilkinson

Ascot Racecourse in the UK is a major international venue for horseracing. The racecourse is being redeveloped to provide entirely new public facilities. The development includes the construction of a new grandstand. A site investigation was earned out comprising mainly cone penetration testing. The site is underlain by the Bagshot Formation, comprising predominately cohesionless deposits of medium dense becoming dense, silty fine to medium sand, containing occasional layers of clay. Shallow foundations would present uncertainty regarding total and differential movement; hence a piled foundation solution was chosen using a continuous flight auger (CFA) piling system. The possibility that piles may found either directly on or within the influence of cohesive material suggested uncertainty regarding toe resistance. In order to measure shaft friction, an instrumented preliminary test pile was undertaken. The results were compared to published correlations of cone and shaft resistance. This approach resulted in a net saving in terms of pile length which resulted in optimum value engineering and hence a cost saving to the client.

Jan 1, 2006

By Karl A. H iggins, James P. Racine

"Displacement Cast-in-Place (DCIP) piles are not a common deep foundation type in the Washington, DC Metro Area market. As a result, less regional data is available for these foundations compared to other alternate deep foundation types. Displacement cast-in-place piles (DCIP) differ from traditional Auger Cast-In-Place (ACIP) piles in that the pile annulus is formed by pushing a partially-flighted, auger bit to depth via a large mandrel. The auger bit includes a displacing body near the bottom of the tooling. Therefore, little to no spoils are generated during installation and the soil around the annulus is largely densified in-place due to the displacing body being slightly larger than the mandrel it is attached to.Due to this densification, one would expect that the theoretical DCIP capacities (compression or tension) would be greater than an ACIP pile (assuming a pile of similar length and diameter). After 20 static load tests and the installation of over 6,000+ piles on the MGM National Harbor Casino Project, the differences in pile support characteristics between DCIP and ACIP piles of same size and depth was small. The performance of both pile types depended on the density and type of soil within the bearing stratum. In some early cases of DCIP use, the performance exceeded expectations and appeared to be more in line (or better) than typical capacities obtained from driven displacement piles. Other times, the tip elevations could not be achieved or were so difficult to achieve that installation delays occurred and/or significant additional engineering effort was required to address piles short of their requirement embedment.This paper will discuss the limitations of DCIP pile installation in dense Coastal Plain soils and will present the lessons learned during this project. The paper will also compare the DCIP pile type to both conventional ACIP and driven displacement piles utilizing regional and site-specific load test and installation data."

Jan 1, 2017

By Michael W. Neill, O&apos

The engineering profession generally does not accept vibro-driven piles as bearing piles unless their capacities can be verified by restriking with an impact hammer, which significantly reduces the economic benefits of vibratory driving. In part, the concern for capacity development in piles driven by vibration arises out of observations that vibro-driven piles do not develop capacities equivalent to those driven by impact (e. g., Mosher, 1987). Nonetheless, if capacities are predictable, vibratory installation may be more cost effective than installation by impact, due to savings in time of installation, even if capacities are lower than those of impact-driven piles. Throughout the past few decades, a number of attempts have been made to develop capacity prediction methods for vibro-driven piles, mostly along the same lines as methods for impact-driven piles. That is, (1) totally empirical formulae, (2) power balance / power transfer formulae, and (3) "time domain-nonlinear" (TDN) computational procedures such as the wave equation. Some of the formulae have been based partly on field experience, but the majority have been developed from simple theoretical models with parameters evaluated from laboratory studies. Neither these formulae nor the TDN solutions have been systematically checked (or modified) by recording appropriate field data over a variety of site

Jan 1, 1989

By Matthew E. Meyer

Renovation, rehabilitation, restoration and expansion of existing residential, retail, commercial, hospital facilities and historic structures requires assessment and evaluation of foundation systems of various ages. The concept of demolition and reconstruction in urban areas is often more challenging, costly, and even prohibitive in some cases due to historic regulations. The authors have been involved with numerous projects related to existing foundation assessment and retrofit, including: hotel and hospital expansions, historic Art-Deco hotel renovations and expansions, garage structure expansions, additions to prominent auction houses, casinos, printing facilities; high-rise structure foundation retrofitting; forensic evaluations of existing building and highway structure foundation systems, and marine bulkhead sheeting systems. The use of non-destructive testing techniques, high-strain dynamic load testing, full scale pile cap load testing and 3-D laser scanning technology has proved to be vital in the assessment and evaluation process, as well as design of foundation retrofit alternatives. This paper presents various methods and techniques to facilitate a phased approach for optimization of existing foundations and subsequent re-use of foundation systems. These methods and techniques are illustrated through the author?s experience and selected case histories from projects with varied foundation and geologic conditions.

Jan 1, 2011

By Janne P. Isohaka, Anssi M. Laaksonen

"Abstract In Scandinavia the use of steel pipe piles in bridge foundations started in the mid-1980s and has increased steadily since. As the piles driven in soft soils are slender, they can fail by buckling. Buckling usually requires taking into account the second order effect in structural and geotechnical design.The purpose of this paper is to derive formulas for demonstrating the theory behind the formulas given in literature for the second order effect of initially bent piles.IntroductionIn Scandinavian countries solid bedrock usually lies at moderate depth. If the bridge site is in an area where the soil above the bedrock is soft, the bridge is usually founded on end-bearing piles resting on the bedrock.The main purpose of the piles is to transfer axial forces into bearing soil. Like columns, piles can lose their stability by buckling when surrounded by soft soil. When axial compression on a slender, initially straight, pile reaches a particular value called the critical load, the pile is subjected to lateral deflection and loses stability. The soil around the pile suffers a corresponding deformation. This soilstructure interaction increases the critical load compared to a pile without surrounding soil.It is very unlikely that piles are ideally straight. Initial curvature along with curvature and deviation caused by the installation of piles causes bending moments to the pile when normal force is applied. These lateral displacements increase when normal force increases. This increase of moment is called asecond order effect.Eurocode and literatureEurocode 7 includes guidelines for the design of piles (Eurocode 3, section 5 includes design of steel piles). However, there are no clear guidelines for considering the second order effects related to piles surrounded by soil. Eurocodes advise doing structural design of piles the same way as in the case of columns. With columns, the second order effect is taken into consideration by multiplying the first order moment with the factor shown below (SFS EN-1992-1-1, 2005):"

Jan 1, 2014

By K. Y. C. Chung

A case study on foundation engineering through organic soils is presented. Located along the west shore of the Hudson River, site soils consist of random brick fill over a thick layer of peat and organic silts or clays. The organic layer is underlain by medium dense to dense sand with varying amounts of silt. Strong artesian pressures were measured in the sand. A pile foundation system was selected to support all structures. To avoid periodic flooding, new fill must be placed on the existing fill. Large total and differential settlements will occur due to consolidation and secondary compression of the organic soils. This settlement will reduce the allowable pile capacity due to the large negative skin friction in the organic layer; and will necessitate long-term maintenance of the final grade elevation. Pile load tests were performed to determine the allowable compression and uplift capacities, long-term capacities and pile driving criteria.

Jan 1, 2010

By George Piscsalko

"Quality control of drilled shafts and CFA piles is greatly dependent upon the practices of the site personnel. In many applications it is difficult or not possible to fully inspect the shaft prior to concreting, such as when the shaft is drilled under slurry. CFA piles are cast with no ability to inspect the shaft prior to concreting. There are numerous methods currently available to assess the integrity of drilled shafts and CFA piles. This paper will compare evaluations by three existing non-destructive test (NDT) methods with a new method of Thermal Integrity Profiling for assessing integrity in drilled shafts and CFA piles. This Thermal Integrity Profiling method determines the integrity over 100% of the shaft cross section, both inside and outside the reinforcing cage, by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements are made typically only 12 to 48 hours after concrete placement, thus accelerating the construction process. Thermal Integrity Profiling will be described in detail and the Thermal Integrity Profile (TIP) results from several shafts with purpose built defects will be discussed along with several case histories from drilled shafts and CFA piles where Thermal Integrity Profiling was used. The case histories will compare TIP with various other NDT tests utilized on these particular piles including comparisons with Low Strain Integrity Testing and Cross Hole Sonic Logging. Test results for the various methods will be discussed and the excavation of the upper portion of one drilled shaft will be shown and discussed. IntroductionDrilled shafts can be a desirable foundation element in many applications due to the large axial and lateral capacities which are attainable for very large drilled shafts. Drilled shafts can be cast in a dry hole which allows for inspection of the hole prior to casting, but the casting process is very difficult to nearly impossible to inspect with any accuracy. Drilled shafts are frequently cast under slurry as a means to stabilize the surrounding soils during the construction process. When casting a drilled shaft under slurry, it is very difficult to accurately inspect the hole prior to casting and it is equally difficult to inspect the shaft during the casting process. CFA piles are another popular choice for their relative ease and speed of installation. The trend has been larger CFA piles carrying greater loads, which makes quality control critical for these piles. Many of the above mentioned processes are blind to inspection and therefore the chances increase for having defects present in the completed elements."

Jan 1, 2014

By J. O. Osterberg

The realities of foundation enginering are that the work never proceeds exactly as expected. The various reasons, exploration, design, construction, and legal are discussed. Case histories are presented with an analysis of why the projects did not turn out as expected and how the difficulties might have been avoided.

Jan 1, 2010

By Emad W. Shublaq

Contractual site plans are implemented for executing pile foundations (5 x 5) at segmental concrete bridge. Project schedule demands have forced the contractor to find out the most economical procedure in achieving the goal. This paper presents a site management technique which is applied by the Contractor. This was found to be fruitful and as much as 60% saving was gained.

Jan 1, 1992

By Madan Kumar Annam, Hari Krishna Y

"Basement construction is one of the challenging geotechnical concerns in the urban environment. Several types of retention systems are practiced to support the earth which is suitable for restricted access, rapid mobilization, fast excavation and cost-effective designs. A thorough understanding of geotechnical engineering as well as the structural mechanics is important for the earth retention systems. This paper discusses a project with various types of foundation solutions including monitoring of deflections during excavation stage of a retention system.A multi storeyed residential building (3B+Stilt+18F) in Chennai having structure foot print area of 1500 m2 has to be constructed on large diameter pile foundations and also to support the proposed basement excavation. Ground water table was encountered at about 6m below the existing ground level (EGL). In order to support heavy structural loads, large diameter bored cast-in-situ piles were chosen and installed. Further, complete retention system was economically designed and built, which includes installation of Contiguous Bored Piles (CBP) in combination of vertical grout columns behind CBP wall to seal the gap between the CB Piles, installation of inclined ground anchors, construction of capping beam, stressing and locking of installed ground anchors. A detailed monitoring program was in place and continuous monitoring of wall deflections is being measured at the time of publishing this paper. This paper describes the design and construction aspects adopted for foundation and retention system including the monitoring results during excavation stage of the project.INTRODUCTIONIn general, stage wise open excavation will be opted for basement construction where plenty of space is available. Due to urbanization and restricted space, open excavation became a difficult task nowadays. To overcome this problem, suitable retention system need to be selected to retain the soil mass. Selection of suitable retention system for multi-level basement excavation is a great challenge in geotechnical industry, especially when the proposed site is located within the minimum set back distance from the existing structures. This in turn calls for the advanced and innovative methods of retention system.Several earth retention systems such as Diaphragm Walls, Secant Pile Walls, CBP system, Soldier Pile Walls, Sheet Piles, Deep Soil Mixing (block walls) etc. with or without inclined ground anchors are being practiced worldwide. Considering the advantages and disadvantages of the available retention systems in practice locally and keeping in view of present site conditions, the developer has chosen CBP system with inclined ground anchors so that all foundation related works of the project will be handled in a single package. The main advantage of such packaged solution will ease the coordination between design consultants and foundation contractor resulting in faster construction of foundation works which in turn reflect savings in time and cost."

Jan 1, 2015

By Robert B. Bittner

The Sutong Bridge across the lower Yangtze River in China will have, when completed, the longest span (1,088 m) and the highest towers (306 m) of any cable stayed span in the world. The foundations for this record setting span will also be record setting. They are located in water depths exceeding 30 m with maximum flows exceeding 3 m/sec. The soil at the site of the main pylons consists of layers of silty sands and silty clays extending to bed rock at 270 m below river elevation. This paper describes the innovative methods used by the team of foundation designers and constructors to support this record setting bridge at this very challenging site. This paper covers three specific topics related to the foundations of the Sutong Bridge: ? Design and construction of the 131 drilled shafts (2.8/2.5 m diameter and 114/117 m long) under each of the two main pylons, including the post-grouting of all drilled shaft tips. ? Design and construction of the scour protection for the two main pylons. ? Construction methods used to construct the waterline pile caps (113.8 m by 48.1 m by 13.3 m deep) under each pylon.

Jan 1, 2007

By Peter J. Nicholson

The methods of reinforcement to be discussed in this paper are all insitu methods, ones that can be used on the soil structure as it exists in the ground, and do not rely on excavation and replacement of the soil. Current practice in the United States, as well as new ideas and methods, will be discussed as they relate to slope stability, retaining walls, and to other uses such as control of mine or cavity related subsidence and to liquefaction control under existing structures. The method is based on the concept of "nailing" or reinforcing the soil in place, and thereby causing a mass of soil to act as a coherent unit. When performed properly, a true gravity structure can be constructed, one that will remain intact under both horizontal and vertical loadings and that will also resist vibrational and seismic loadings.

Jan 1, 1991

By G. Sauer

"More Skill is needed to avoid rather than to handle heavy ground loads." This finding, from a tunneling engineer of the nineteenth century, is still relevant today with all advanced sequential excavation and support methods available whether they are applied in the vertical or horizontal direction. Balanced contractual agreements and documents are important since they provide the spirit and climate at the site. This article aims to describe the means and measures for 'hand mined' shaft and tunnel support as they are available today. Some special construction elements and methods with a perspective in recent developments in order to avoid getting stuck in conservatism are presented as well. If we don't allow new methods, means and measures we may end up with the famous quote "Only women who have already proven they are able to give birth to a healthy baby are allowed to become pregnant!"

Jan 1, 2003