Search Documents

By S. Frimpong

Hydraulic shovels are widely used for primary production in surface mining operations. Variability in material diggability, unstructured mining environments and limited space and operator inefficiency affect the performance of these shovel excavators. Dynamic models of the hydraulic shovels are essential for understanding and improving machine performance. This paper contributes to this subject area by advancing hydraulic shovel kinematics and dynamics using the modified Newton-Euler method. A virtual simulator is developed to simulate the hydraulic shovel performance in the ADAMS environment. The simulator is validated with data on shovel geometry and the physical and mechanical properties of a formation in a surface mining environment. The results indicate that a shorter digging time increases the shovel operating power requirements, and that the required peak power increases by 100% when the digging time reduces by 50%. Simulation results also show that a shallow trajectory facilitates the digging process, with 50% reduction in peak power requirements compared to a deep one. This simulator provides a powerful tool for performance monitoring, excavation process designs and structural optimization of hydraulic excavators. This work also forms the basis for developing comprehensive simulator models for automated shovel operations in constrained mining environments.

Jan 1, 2005

By Tarrant Elkington

Underground mine planning practices are typically manual and time consuming and will often produce sub-optimal solutions due to the application of generic rule-of-thumb assumptions or ?tried and tested? choices. The development of computer-automated tools for underground mine planning enable a wide range of scenarios to be considered rapidly in arriving at an optimised solution, subject to input assumptions. We have applied these tools to demonstrate ?optimised? solutions that challenge industry standard practices. Further, we have incorporated grade and price/cost uncertainty into these tools to gain an understanding on how the consideration of uncertainty may further alter strategy selection. Finally, we enable the tools to dynamically adjust cut-off grades in conjunction with the evolution of prices/cost.

May 1, 2010

By David Rahal, Des Erasmus, Ken Major

"Over the past twenty years there has been an increased emphasis on fine grinding in the minerals industry. This spurred the development of a range of new fine grinding equipment in the 1990s. At that time, the Knelson-Deswik mill was developed in South Africa for the pigments industry.Knelson Milling Solutions currently offers a wide range of laboratory, pilot and production scale mills. These mills bridge the gap between traditional low speed vertical mills and the high speed horizontal mills (tip speed < 3 and > 15 m/s respectively). They are designed to run at tip speeds between 10 and 12 m/s and are capable of operating with very dense grinding media. The result is a power intensity that is higher than the low speed mills and overlaps that of the high speed mills. This allows the mill to be customized for a wide range of grinding applications.A case study at Aquarius Platinum’s Kroondal Mine shows that the Knelson-Deswik technology can produce a consistent product size despite feed variations. It also shows that the throughput was proportional to the slurry density at Kroondal. The case study identified increasing the slurry density as a process change that can increase throughput and reduce the specific energy consumption.INTRODUCTIONThe increasing complexity and finer grain sizes of modern ore bodies have increased the importance of effective mineral liberation in obtaining acceptable grades and recoveries (Jankovic, Valery and La Rosa, 2003; Lichter and Davey, 2006; Napier-Munn, Morell, Morrison and Kojovic, 1996). This trend has increased the significance of fine grinding technology because the input energy increases exponentially as the required product size decreases from 100 to 10 microns (Gao and Weller, 1993a).The US Department of Energy recently provided the context for the potential energy savings in the US Mining Industry (BCS, 2007). They reported that grinding consumes approximately 494 TBtu/year. This was over double the consumption of the second highest equipment category, diesel materials handling systems (211 TBtu/yr). The proportion of grinding energy allocated to fine grinding can only be expected to increase as finer ore deposits are mined. It is therefore critical that fine grinding efficiency continue to improve through the selection of appropriate equipment and the development of best practices for existing applications."

Jan 1, 2011

"INTRODUCTIONGold tailings retreatment plants have been operated for many years throughout the world. Several large tailings retreatment facilities have been operated profitably in South Africa since 1976 and there are tailings retreatment operations in Canada currently in production with more in the feasibility stages.The Timmins Gold Tailings Project of ERG Resources Inc. was designed to treat 8,000,000 tonnes per annum of gold tailings for an eight month operating season, and commissioning of the operation began in July 1988. The payback period for this project is about 3 years which corresponds to an IRR of 30%.This report summarizes the metallurgical characteristics of the reclaim tailings, describes the process flowsheet which was developed to enable ERG to economically recover gold from the Timmins area tailings, and reviews commissioning activities."

Jan 1, 1989

By Adil Aledresse, Louis Mercier, Laxman Amaratunga

"The development of high capacity adsorbents with uniform porosity denoted, MP-HMS (Mercaptopropyl – Hexagonal Mesoporous Structure) using nanotechnology, and their ability to extract gold from solution, is presented. The preparation of highly effective heavy metal ion adsorbents by the incorporation of thiol moieties into the pore channels of mesoporous silica molecular sieves has been the subject of many nanotechnology research investigations. The unique feature of these nanoporous adsorbents is their ability to adsorb gold ions from ultra-low concentration solutions like mine effluent as well as from leached solutions in gold mills. The preliminary studies from laboratory simulated gold solutions show that the adsorption capacities of these materials are also among the highest reported. MP-HMS has shown the capability to adsorb 370 mg gold per one gram of the nanomaterials from Tetrachloroaurate solution (up to 37% of their weight). Experimental studies indicated that the maximum adsorption of gold (as high as 99.9% recovery). The current studies will be extended to investigate the interaction of ionic gold complexes with nanomaterials. Future development of this work may lead to either to replace the conventional CIP/CIL processes or use nanomaterials in tandem with the former, suggesting plausible use of mesoporous material in pulp, MIP or in leach, MIL, as a novel gold extraction process.INTRODUCTIONGold typically occurs at very low concentrations in ores less than 10 g/t or 0.001% (mass basis). At these concentrations the use of aqueous chemical (hydrometallurgical) extraction processes is the only economically viable method of extracting the gold from the ore. Typical hydrometallurgical gold recovery involves a leaching step followed by the separation of the gold bearing solution from the residues, or adsorption of the gold onto activated carbon adsorbent. After elution from the activated carbon the gold is further concentrated by precipitation or electrodeposition."

Jan 1, 2008

By Colin Hardie, Erik Bartsch, Guy Comeau

"The Xstrata Nickel Raglan Concentrator, located at the northern limit of Quebec’s Nunavik region has been in operation since 1997. Originally designed to process 800,000 tonnes per year of high grade nickel ore, plant capacity is currently approaching 1,200,000 tonnes per year due to an Optimization Project (FAG to SAG conversion) in 2005 and many recent processimprovements.In 2006, the Raglan Metallurgical Group with assistance from the Xstrata Process Support group decided to make SAG control one of its priorities in order to further increase throughput and improve stability. The original primary mill control logic delivered by the Optimisation Project in 2005 consisted of a simple PID loop controlling the mill charge (bearing pressure) through feed rate changes. Due to the multivariable, non-linear and disturbance dominated nature of the SAG circuit it was quickly found that this traditional PID control strategy was not able to adequately control the mill; resulting in poor stability, frequent operator interventions and less than optimum performance.This paper describes the successful integration of advanced field systems such as mill feed image analysis (Wipfrag) and crusher gap controller (ASRi), into a multi-variable fuzzy logic SAG mill controller. The process of how a strategy for control was developed and implemented directly in the existing control system (exploiting standard system capabilities) is discussed. It is also shown how this approach has provided mill automation which is simple, robust (despite erratic feed characteristics), and delivers both an increase in throughput and a reduction of variability.INTRODUCTIONOriginally commissioned as a Fully Autogenous Grinding (FAG) circuit in 1997, preparations to convert the Katinniq Concentrator Mill to SAG had in fact commenced as early as 1999, but were halted owing to alternative process improvements which achieved up to 1Mtpa as early as 2000. Up until this time, plant process controls had remained more or less static; modifications having been limited to those required by new equipment. Primary mill process controls and related measurements were at this stage limited to:"

Jan 1, 2008

"The effective thermal conductivity (ETC) is one of the most important thermo-physical properties of porous media. Due to the lack of higher precision influence of temperature on thermal conductivity, we took 6 groups of experiments on rock samples (including igneous rock, sedimentary rock and metamorphic rock) under different operating temperatures from 20? to 50? by 7 acquisition points. The general equation of thermal conductivity drives the value of it increasing along with the decreases of the temperature. While in our experiments, it is easy to find a singularity among them for each sample. The experimental investigations we attempted to observe and interpret the alteration mechanism. According to the Heat Capacity Theory in solid state physics, this research gives the explanation about the “singularity” from 3 understanding of specific heat, average free path, and thermal conductivity. Our research divided the condition of the rock thermal conductivity into 3 different types. INTRODUCTION The effective thermal conductivity (ETC) is one of the most important thermo-physical properties of porous media(Huang & Han ,1988; Peierles ,1955). This parameter is necessary for analysis of heat transfer(Vaferi et al, 2014;Hans-Dieter & Rudiger,2003). It’s well known that a general equation for ?(T) was set by Sass et al. (1992) which based on the coupled effect of composition and temperature on the thermal conductivity(Jesse et al, 2013; Mongelli et al,1982).The equation was further successfully verified for other rock (Zumrud et al,2010;Abdulagatova et al,2009;Seipold& Huenges,1998).Thermal conductivity is also related to other physical proper ties of porous rock, such as thermal diffusivity, heat capacity(Brettmann et al,2011;Abuel-Naga et al,2008). It is well known that ETC and other thermo physical properties of rock materials are affected by various factors, such as temperature, pressure, mineralogical composition, porosity, stratification, size and shape of the components, and nature of pore fluid, etc. (Tiedje & Guo, 2014; Touloukian et al,1970).The understanding of heat transport processes still requires the knowledge of thermal properties of rocks."

Jan 1, 2015

By Klaus Tietz, Hamish Adam, John Selby, Ian Glazier, Brian Sinfield

"Room-temperature tunable diode laser (TDL) analyzers are gaining in acceptance for highly critical safety monitoring applications in a variety of industries. This paper describes the testing, evaluation and deployment of a laser-based hydrogen cyanide monitoring system at the Campbell Complex of Goldcorp’s Red Lake Gold Mines in Balmertown, Ontario, Canada.A trial, single channel installation was followed by a staged multi-channel installation. Unexpected technical issues with the multi-channel installation were addressed and resolved.INTRODUCTIONLaser-based gas detection has several advantages over existing gas detection techniques (Ballangrud, 1993; Silver, 1992; Bomse, 1995; Table 1). For practical purposes, lasers generate light at a single wavelength. Room temperature tunable diode lasers (TDL) emit light in the near infrared (NIR) part of the electro-magnetic spectrum. Many gases of interest, including HCN, NH3 and others, absorb energy in the near infrared (NIR). Each gas has a unique absorption signature, or spectrum, made up of a large number of individual “absorption lines”. A TDL can be tuned to select a single absorption line of a target gas, which does not overlap with absorption lines from any other gases. Therefore, laser gas sensing is selective and does not suffer from interference from other gases. The single-wavelength nature of laser light also means that laser gas analysers have a linear response over a wide dynamic range.Tunable Diode Lasers (TDL) generate only a few mW of power. However, all this power is concentrated at one wavelength, the wavelength where gas absorption occurs, resulting in high signal-to-noise ratios and short response times, typically of about 1 or 2 seconds (Ballangrud, 1993). This also means that long path lengths can be used, enabling accurate measurements of very low concentrations, even with weakly absorbing gases. Tunable Diode Lasers provide all the advantages of other semiconductor devices: they are small, solid-state devices, operate at room temperature, and have long-term reliability (over 15 years). Currently, they can be obtained for any wavelength throughout the NIR (700nm to 2000nm). Because many gases absorb in the NIR, the technique is widely applicable."

Jan 1, 2011

By Dave Bulled, Khiratt Husain

"The use of High Pressure Grinding Rolls is gaining significant interest as a replacement for SAG milling in the comminution of hard rock ores because of the potential for reduced costs in terms of energy and grinding ball consumption. Estimation of expected energy consumption for fullscale operations has conventionally involved the testing of a few fairly large samples in pilot scale HPGRs. This paper describes the development of a small-scale batch test method for determining a work index for HPGR of a large number of samples that can be used to show the variability of the ore as an integral part of a geometallurgical approach to circuit design and production forecasting.The test equipment that was developed comprises a hydraulic press with adjustable pressure operating on small batches of ore in a locked cycle test procedure. A work index measurement was determined that links the specific energy consumed in the test to the breakage achieved such that the index can be used to predict comminution energy requirements.The measurements were calibrated against laboratory scale HPGR equipment to develop a model for design and forecasting that includes crushers, HPGRs and ball mills in a complete comminution circuit.INTRODUCTIONEstimation of the expected energy consumption for full-scale HPGR operations has conventionally involved the testing of a few fairly large samples in laboratory and pilot scale machines (Danilkewich, 2006). With the financial input of five mining corporations, SGS Lakefield Research has developed a small scale test capable of providing relevant information on the variability of energy consumption and size reduction from drill core samples. It is our intention that the values measured in the test will be scaled up, through benchmark comparison with pilot sized and full sized HPGR units, to allow plant design and throughput forecast on a block by block basis of the mine plan using a new CEET program. CEET® (an acronym for Comminution Economic Evaluation Tool) is an advanced grinding design and performance predicting tool that uses energy relationships to model the performance of SAG / Ball mill circuits."

Jan 1, 2008

By J. S. Phipps, D. R. Skuse

"Aqueous slurries of fine particle size calcium carbonate are used in a diverse range of end-use products. In many cases, the end use performance is governed by the fineness of the particle size distribution. In turn, the maximum fineness of the particle size distribution is primarily determined by the efficiency of the dispersants used during the production process. Here we report the sodium polyacrylate mediated dispersion of calcite and kaolin. Firstly, we report a colloid chemical description of the dispersant behaviour and attribute the stabilisation to both steric and electrostatic mechanisms. Secondly, we describe how the understanding developed in the first part of the study can be utilised to produce more effective dispersant systems which allow the preparation of, added value, higher solids and finer particle size calcium carbonate slurry products.INTRODUCTIONConcentrated aqueous dispersions of fine, particulate kaolin and calcium carbonate are used extensively in the coating of paper. Currently more than 10 million tonnes of such dispersions are used annually in North America and Europe alone, and worldwide consumption is growing at around 3% per year.Generally, paper is coated to enhance its visual appearance. Firstly, coatings improve the optical properties of the blank sheet, i.e. its brightness (or whiteness), opacity and gloss. Secondly, they improve the physical properties of the sheet that will influence the quality of the final printed image, such as surface smoothness, porosity, and ink absorption. In order to achieve these aims economically, paper coatings must be applied at high speeds and with minimal drying costs.Kaolin and calcium carbonate pigments are the major components of most paper coating formulations. Particle size distributions are chosen to maximise the optical benefits that they confer, and to allow the production of formulations that can be easily pumped, handled and coated. Coating pigments are generally produced and transported as slurries, and so it is important to obtain dispersions with the highest possible solids content, both to minimise drying costs and the quantity of water transported. This paper examines the dispersant technology that is currently used in the industry and the mechanisms by which it functions, and illustrates ways in which this technology has developed and could be further improved in the future."

Jan 1, 2003

By Ryan W. Ulansky

This paper presents the conceptual design of a magnetically-levitated skip for use in an underground mine. A skip is used to move rock from an underground mine to its surface processing facility. Conventionally the skip is raised and lowered by cables, similar to an elevator. In a magnetically-levitated skip, the cable is replaced with a linear induction or synchronous motor to provide propulsion and levitation. Removal of the cables in a magnetically-levitated skip provides many advantages over a conventional system including the ability: to negotiate corners, to travel vertically in the shaft as well as horizontally to the mining face, and to move a very large volume of material using multiple skips in a small shaft. A magnetically-levitated skip is a safer, more environmentally-friendly, productive alternative to conventional skipping. It has the further advantage to decrease haulage distances for underground vehicles.

May 1, 2002

By Eugen Gluck, Gus Van Weert, Peter Kondos

"Microwaves have the capability to heat up sulphides, especially clusters of particles of approx. 1 mm. Some sulphides absorb microwaves more readily than others. Molybdenite is especially effective in this regard, possibly due to its flaky nature and/or electrical conductivity. Even where it occurs in low concentrations in a deposit, individual rocks may be ore grade due to the high monetary value of MoS2. Such rocks often result from crushing mined veinlets or stockwork, or are contained in the cutoff grade fraction of ROM. Machine segregation of rocks high in MoS2 by infrared sensors after microwaving could therefore advantageously be used to upgrade lower grade ore between Mine and Mill. This would reduce the size of the latter, and thus its CAPEX and OPEX. Such upgrading could also yield shipping ore for a distant Mill, or extend ore reserves.Barrick Gold Corp. has been supporting the development of MW/IR sulphide sorting for the past three years. The results of MW/IR sorting work on molybdenite and other (pyritic) ore samples from a variety of sources are being presented here.INTRODUCTIONThis paper looks at mechanized, i.e. machine ore sorting technologies currently available and under development, and what conditions would be needed for the potential application of such ore sorting to sulphide mining and milling. Current machine sorting involves no-contact sensing technology for rocks, and signal processing after sensing to activate airblast segregation of certain rocks, normally the smallest mass to keep compressed air costs down.The forerunner of modern sorting is probably magnetic separation, which utilizes an inherent property of certain ores to divert it into mag and non-mags fractions. Radiometric ore sorters, which have been applied successfully for decades in the pre-concentration of uranium ores (Wotruba and Riedel, 2006) initiated modern sorting. In the 90’s, sensor-based machine sorting became a viable means of increasing the overall economic recovery of a resource. This technology became driven by the availability of low cost computing equipment and the concurrent development of algorithms, and by the availability of extremely fast response sensors and air actuators, allowing the sorting equipment to run faster, dropping the cost per tonne. It has been in industrial minerals processing that rock sorting has been most widely adopted, not really surprising. Liberation occurs on a different scale than in the base metal industry. Most industrial minerals are mined from massive deposits, requiring (in the past) no upgrading. Many of these operations now run into product contamination problems, which ore sorting can solve. One illustration: in Finland, a quarry is separating limestone from dolomite at 500 tonnes / hour, with individual rocks weighing up to 15 kg. Many of these industrial minerals operations have stockpiles of earlier discarded below-quality rocks, now being reprocessed with the help of ore sorting. The economics of this are very favourable, going from zero or negative value (stockpiles can not be left when closing the mine) to full product value for at least a portion of the stockpile. This suggests that in the future the economics of overburden sorting could become attractive under the right circumstances and such treatment could well become an integral part of open pit mine development."

Jan 1, 2009

By Y. Guglielmi, C. Gout, P. Henry, P. Dick

The key questions about fault reactivation in shales concern the potential enhanced fluid displacement through a previously low-permeability aseismic shale formation. Here we selected a critically-stressed fault cross-cutting the underground research facility of Tournemire (France) which is located in Toarcian shales. Several inclined boreholes were drilled across the 8.5 m thick fault zone characterized by a fractured damage zone (FDZ) and a central 2.4 m thick complex core (FC) made of multiple shear bands with gouge intercalated with highly fractured lenses. The fault was pressurized using a straddle packer system defining a 2.4m long injection chamber normal to the fault surface. Three fault zone intervals were tested, two in the fault damage zone and one in the fault core. A three-dimensional displacement sensor set in the chamber allowed continuous synchronous coupled monitoring of fault movements, injection pressure and flow rate. An anticlockwise 0.22-to-0.05 mm fault slip was captured associated with a 10-to-100 hydraulic aperture increase of the fault. Preliminary analyses of the experiments show that leakage in the fault zone is controlled by strength and stress magnitude contrasts between the fault core and the fault damage zone. Fault damage zone discontinuities display a much higher peak static friction angle than the fault core shear zones, respectively of 34 and 22° that could be related to complex interactions between healing and sealing processes. Fault core leakage is much more dependent on strain than on effective stress variations. Discontinuous, pulse-like leakage, develops following complex failure processes that may simultaneously take place in the gouge zones and along the large pre-existing discontinuities. Such results may be of importance in evaluating fault seal integrity in oil and gas exploration, production or CO2 storage or underground excavations monitoring.

Jan 1, 2015

By B. Jago

From the perspective of metallurgical processing, gold ores can be classified into freemilling and refractory ores. Their extractive metallurgy is largely driven by mineralogical factors such as gold particle size, association with other minerals, coatings and rimmings, presence of cyanicides, oxygen consumers and preg-robbers, presence of refractory gold minerals, and invisible gold in sulphide and sulpharsenide minerals. Gold process mineralogy helps address issues and problems related to gold ore processing. It is widely used as a predictive and trouble-shooting tool in gold ore processing, and provides useful information on process selection, flowsheet development, recovery improvement, and reagent consumption optimization. By combining classic mineralogical techniques, modern instrumental analysis, and diagnostic metallurgy, the mineralogist is able to balance the various types of gold occurrence in an ore.

Jan 1, 2006

By Flavio Rojos-Tapia, Oscar Pereira-Cerda, Samuel Sánchez-Pino, Samuel Sánchez-Baquedano

"Pneumatic flotation was introduced to the Chilean Copper Mining Industry in 1993 by Ingeniería de Minerales S.A. (IDM). The technology is based on the designs of Dr. Rainer Imhof from Germany, who is the designer of several different types of pneumatic flotation cells, already sold through his Company Maelgwyn Mineral Service Limited (MMH). The company is represented by Ingenieria de Minerales S.A. (IDM) in South America.Pneumatic flotation, has been used in tough industrial applications .It has been successfully used for metallic ores such as copper sulphide and oxide minerals, copper slag, silica and silicates from iron magnetic preconcentrate (reverse flotation) and gold. It has also provided promising results when applied to molybdenum flotation. The latest applications, with ultrafine molybdenum particles in operating plants, is showing the V and G Cell (end model designed) as a real technological alternative to conventional flotation., The G Cell is an extremely high speed flotation machine with high selectivity which introduces the possibility of producing a final molybdenum concentrate with only one stage of cleaning. This is a completely new development in molybdenum flotation in the industrial circuit which has the potential to dramatically reduce the circulating load in the cleaning circuit. As a consequence the capital costs of future Molybdenum plants may also be reduced. The suitability of the G Cell will have to be determined on a case by case basis but it provides the metallurgist with an alternate flowsheet for consideration.The good performance of the G Cell can be explained by the high gas hold-up and very effective micro-turbulence which helps improve the attachment of solid particles to the bubbles. This technology may change our traditional concept of residence time in flotation. Additionally, the rotation phenomena introduced in the vessel of the G Cell ,creates radial separation forces which are critical to achieving a more rapid separation of the target minerals from the tailing. This results in a much reduced residence time requirement in the flotation machine. Some benefits associated with the use of the new G Cell are: less energy consumption, less maintenance costs, simple and reliable circuit to operate and a small area required for installing the circuits.As a result of the industrial experience in the Chile, the pneumatic flotation type G Cell can be regarded as a technology which must be considered as a replacement technology for the rougher and cleaner stages for fine particle flotation."

Jan 1, 2008

"Geoscan is used for multi-elemental analysis of conveyed bulk materials in the minerals industry with proven performance and demonstrated paybacks of weeks or months in iron ore, manganese, copper, zinc-lead and phosphate industries. Geoscan-M measures continuously through the full bed depth and is unaffected by belt speed, particle size, layering, mineralogy and dust levels. Increments of typically two minutes are accurately measured and provide the plant operators with tonnage weighted results of contained elements. Measurement of the composition in real time enables prompt feedback to the mining operators and also feed forward to the process operators. Crushed ore increments can be diverted based on composition, such as diverting waste for disposal or marginal material to a stockpile for separate processing. Bulk sorting allows material to be placed into relevant stockpiles for subsequent blending to achieve consistency for process feed. Parameters used for decisions may be primary metal content, deleterious component content, other process parameter, or a combination of these. Process parameter may be the elemental ratio between critical components, e.g. Cu:S ratio, basicity, or the content of an “indicator” element (such as Si indicating material hardness). Benefits will be discussed based on case studies in copper and iron ore.IntroductionAs operators of process plants strive to remain competitive as capital and operating costs increase and commodity prices fluctuate, more focus has been directed at incremental performance improvements at incremental cost rather than major expansions to increase output. The philosophy of working smarter allows plants to adopt technologies proven in other industry sectors to minimise risk. This paper discusses one such technology that the minerals sector is adopting and has found to be safe, reliable and accurate with paybacks of weeks in most applications. New applications continue to be found and major benefits realised at various stages in the processing and handling of ores and products."

Jan 1, 2016

By J. R. Goode

"Coarse ore sorting is here defined as the physical separation of a mixture of coarse (+3/8 inch) ore particles into two or more separate groups of total value greater than that of the unsorted ore. An ore will probably be sortable if the geology of the orebody and the mining practices employed meet conditions outlined in this paper.The paper points out how sorting can substantially reduce tonnage variable operating costs because sorting can double the mill head grade of amenable ores by rejecting waste rock from the mine output. The effect of sorting on ore reserves is outlined. It is also suggested that sorting is a low cost alternative to conventional expansion.The mode of operation of the Ore Sorters Kadel 13 Photometric and MK VI A Radiometric sorters is detailed. The report concludes with detailed descriptions of the photometric sorting plant operated by the Doornfontein Gold Mining Company is South Africa and the Radiometric Sorting Plant presently under construction at the Schwartzwalder mine of Cotter Corporation in Colorado."

Jan 1, 1975

By Renaud Adams, Vladimir Salatic

"The El Mochito Mine located in Honduras, Central America, has produced lead, zinc and silver in concentrates since the 1950s. The paper discusses changes made in both lead and zinc circuits to reduce costs while maintaining production during the recent period of low metal prices.The intent of this paper is to show that sometimes thinking “outside the box” is beneficial for progress. Also, in striving for better metallurgical results we should not forget the basics of flotation. Sometimes the latest trends may not be applicable to the ore we are treating and may not meet the operating cost constraints.A major beneficial impact on El Mochito metallurgy was achieved when the overall grind was coarsened, eliminating the significant percentage of slimes. Switching from two parallel twostage grinding circuits to one circuit with three-stage series grinding has resulted in a significant reduction in power and steel consumption. With minor layout/reagent modifications, both lead and zinc circuits gained not only in retention time but as well in producing better grade products.Of course, the challenges are still there; they exist and only with the full support of operational data collection and metallurgical laboratory investigation success can come. That is why, we as professionals, can never stop in trying to make the most of what we have.INTRODUCTIONThe El Mochito Mine is owned by American Pacific Honduras S.A. de C.V. (AMPAC) a subsidiary of Breakwater Resources Ltd. Of Toronto, Canada. The mine is located in western Honduras, approximately 220 kilometers northwest of the capital city, Tegucigalpa and 90 kilometers south of the country’s second largest city, San Pedro Sula. The mine began operating in 1948 and to date has produced more than 19 million tonnes grading 240 g/t Ag, 3.5% Pb and 7.4% Zn. Production in 2005 was 700,190 tonnes grading 87 g/t Ag, 1.85% Pb and 6.61% Zn.Decreasing metal content in the ore followed by the lowest zinc price on the market in the last 15 years (see Figure 1) has reduced the cash flow and endangered to stop the operation."

Jan 1, 2007

By Jodi Roberts, Curtis Deredin, Jean-Guy Paulin

"Since the establishment of the Six Sigma quality improvement program in 2001, several projects have been successfully carried out in the copper-lead, zinc, copper separation, lead upgrading and bulk flotation circuits in the Brunswick Concentrator.This paper provides an update on the process improvement initiatives that have taken place since 2004 using the Six Sigma methodology:•,The recirculation of warm water to the flotation circuit (to save on energy costs)•,Installation of a heat recovery tower to recuperate the heat lost from the zinc dryers•,Installation of an extra row of cleaner-scavenger cells for the copper-lead circuit for extra capacity, and a new reagent scheme for the copper separation circuit that have increased copper and lead recoveries.INTRODUCTIONThe Brunswick Mine Concentrator (Xstrata Zinc Canada) is located near Bathurst, New Brunswick and is one of the world’s largest lead/zinc mines. Milling of ore commenced in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore from the No. 6 open pit mine. The concentrator utilizes selective flotation to produce zinc, lead, copper, and bulk lead/zinc concentrates. The ore is a complex massive sulphide, consisting of approximately 20% valuable minerals, 60% pyrite and 20% silicates.Figures 1, 2, and 3 illustrate the historical annual average metallurgical performance and process improvements achieved at Brunswick Mine for the zinc, lead and copper concentrate products. The objective is to continuously direct metallurgical performance towards increasing grades and recoveries while minimizing operating costs."

Jan 1, 2008

By Robert E. McIvor

"The design/optimization of the pump and cyclones to maximize grinding circuit efficiency first requires a concise understanding of, and clearly defined specifications for, desired grinding circuit performance. Subsequently, the pump and cyclone performances that provide the desired grinding circuit performance can be defined. Once the performance requirements of each process unit are determined, selection of physical equipment parameters that will deliver those performances can be carried out.The Functional Performance Equation shows that there are two distinct efficiencies in closed circuit ball milling. One of these, “Circuit Classification System Efficiency” (CSE), is the fraction of “coarse” material inside the ball mill upon which grinding energy is deliberately expended, versus the remaining fraction of “fines” or finished size material inside the mill, upon which grinding energy is wasted (on over-grinding). The role of the pump and cyclones is to maximize CSE, which is the desired grinding circuit performance. The obtainable target CSE for any given circuit can be estimated, for example, by referring to a plant data base of CSE’s. Design/optimization guidelines then allow us to specify the pump and cyclone performances that will achieve the target CSE.This paper outlines the step-by-step, systematic method of pump and cyclone selection which maximizes CSE. Numerous examples of its successful application are provided.THE FUNCTIONAL PERFORMANCE EQUATIONObservation of the feed and product size distributions going into and discharging from the mill in grinding circuits with low versus high circulating load ratios initially led to the definition of “Circuit Classification System Efficiency” (or CSE, McIvor, 1988a), and subsequently the discovery of the Functional Performance Equation (McIvor, 1988b; McIvor et al, 1992). The CSE is the fraction or percentage of “coarse” (usually in reference to the plus P80) size material inside the mill, versus “fines” or product size material finer than the circuit P80. It can be readily calculated by taking the average of the percentage of said coarse material in the mill feed and mill discharge streams. As this also represents the percentage of the mill energy expended on targeted, coarse size material, it is directly proportional to overall grinding circuit efficiency and production rate. This is all clearly expressed in the Functional Performance Equation for ball milling circuits, for which the derivation has often been presented (e.g. McIvor, 2006)."

Jan 1, 2011