Search Documents

"These guidelines, implemented in 2003, were recommended by the Diamond Exploration Best Practices Committee established by the Canadian Institute of Mining, Metallurgy and Petroleum. The guidelines are applicable to public companies and their consultants reporting diamond exploration results.“The guidelines are referenced in the Companion Policy of NI 43-101 with a statement that disclosure regarding the reporting of diamond exploration sampling results should conform to them.”Reporting GuidelinesThe following guidelines have been recommended by the Diamond Exploration Best Practices Committee established by the Canadian Institute of Mining, Metallurgy and Petroleum. These guidelines are applicable to public companies and their consultants reporting diamond exploration results.In respect of these guidelines, Diamond Exploration Results are results derived from the initial activities undertaken to investigate a diamond bearing prospect or deposit, to generate tonnage, grade and value estimates that cannot be classified as a Mineral Resource or Mineral Reserve. They do not address the earlier stage reporting of geophysical, geochemical or kimberlite indicator mineral results.Public reports of Diamond Exploration Results relating to mineralization not classified as Mineral Resource or Mineral Reserve must address the confidence limits of the result and contain sufficient information to allow a considered and balanced judgement of the significance of the results.The objective of these guidelines is to assist public companies and consultants in making appropriate disclosure of diamond exploration results by reporting in a manner which is:Uniform within the diamond exploration industry; Consistent with reporting from other industry sectors .Comprehensive .Unambiguous .The guidelines are not prescriptive. Materiality is the overriding principle that determines the information that should be disclosed. However, where a company or consultant deviates from the guidelines, the disclosure or technical report should state the extent to which the guidelines have not been followed, and the reasons for the deviation.The guidelines do not in any way replace jurisdictional reporting requirements (For example, the requirement for Canadian reporting issuers to comply with Canadian Securities Administrators National Instrument 43-101 by having technical disclosure endorsed by a Qualified Person as defined in that legislation)."

Jan 1, 2003

By J. F. Henderson, N. H. . C. Fraser

"Camlaren Mines, Limited, owns a group of claims near Gordon lake, in the Northwest Territories about 45 miles northeast of Yellowknife. The Hump vein on the property was explored continuously from the summer of 1937 to December, 1938, when all work was stopped. The two-compartment vertical shaft sunk near the vein is 380 feet deep and drifts and cross-cuts on the 200- and 350-foot levels total 2,241 feet . This exploration indicated 13,177 tons of ore with a gold content of between ½ and 1 ounce a ton1GEOLOGY AND STRUCTUREThe property is underlain by remarkably fresh greywacke and slate of the Early Precambrian Yellowknife group. The thickness of the b ~ds averages 1 to 2 feet, although that of the coarser greywacke may be 10 feet or more. Most of the greywacke beds show a gradation in grain from sandy at the base to slaty at the top. They are composed of chlorite, sericite; carbonate, and detrital quartz and feldspar grains.The structure of the greywacke and slate underlying a part of the property of Camlaren Mines, Limited, is shown in Fig. 1. The beds are isoclinally folded so that they dip at steep to vertical angles and at many places are overturned. The axes of the folds are 50 to several hundred feet apart, and generally plunge at angles of 45° or steeper. The beds along the axes of the folds generally meet to form a sharp V, and at the point of the V, or axial part of the fold, the beds are commonly ruptured . Minor faulting movements along the broken crests of the folds in many cases result in well-defined shear zones. Discontinuous quartz veins and irregular lens-like masses of quartz lying more or less parallel with the bedding are plentiful throughout the sediments, but tend to be concentrated along the ruptured and sheared, anticlinal and synclinal fold axes ( Fig. 1)."

Jan 1, 1954

Adaptive Processing as proposed in geometallurgy has to rely on spatially interpolated information on geometallurgical parameters like phase composition, size distributions of particles of different phases, grain shape parameters, and portions of value elements in different grains. Using the geostatistically predicted values for adaptive processing, e.g. for the selection of milling diameters, thresholds in physical separation, or choices on using an extra pre-separation step, is typically not optimal. Mathematically this effect is introduced by two forms of nonlinearities: 1) The nonlinear scales of compositions, distributions, and shapes have special properties with respect to geostatistics. Classical geostatistics creates some artefacts for these nonlinear scales. On the other hand, modern geostatistical procedures adapted to these scales do not provide unbiased results with respect to linear transformations of the data (e.g. biased block estimates). 2) Neither economic nor ecological effects (e.g. monetary gain) of processing decisions are linear in the interpolated geometallurgical parameters. These nonlinear transforms are not unbiasedly estimated by the likewise transformed unbiased geostatistical predictions of the geometallurgical parameters. Furthermore, we need to optimize the conditional expectation of the gain, rather than obtain an unbiased estimate. Standard geostatistics as such does not provide the "right sort" of estimates for adaptive processing. A nonlinear kriging procedure is needed to approximate the nonlinearities mentioned before. We propose to solve these problems simultaneously using a nonlinear geostatistical technique for predicting the target function (the monetary gain), rather than to predict the geometallurgical parameters and compute the gain from them. The optimization can then be performed directly on this estimated function. It can be shown that this optimization performed on the conditional expectations, not on unbiased predictions, would yield the best possible processing choice. We propose a procedure choosing the processing parameters on an approximation of the conditional expectation. The difficulties with the classical approach and the effectiveness of this new approach are illustrated by a simplified simulation example with a single processing parameter and a simple dependence on the microstructure.

Aug 1, 2013

Unplanned open stope hanging wall dilution is a significant cost for many open stope mining operations. Significant advances in empirical and analytical approaches for estimating stope dilution have been made, however, many important factors are still either ignored or assessed in purely subjective terms. There are many hard to quantify factors that simultaneously influence opening stability and dilution. This creates a significant difficulty for determining the influence of a single variable, such as exposure time, on opening stability. Open stope exposure time has been found to be one of the important factors that influences overall stope stability and dilution. A study is currently being conducted to quantify many of the factors influencing open stope dilution. The assessment of a large comprehensive case history database of Hudson Bay Mining and Smelting Co. Ltd. (HBMS) operations forms the basis of this study. This paper presents the findings of a study on the influence of stope exposure time on open stope dilution. The study is based on applying existing empirical stope dilution prediction methods to the extensive HBMS database. Minimising stope mucking time has been recognised as a method to significantly reduce stope dilution. Factors which influence hanging wall dilution, such as drill and blasting methods as well as undercutting the hanging wall, have been applied to reduce the scatter in the database. Empirical design techniques based on rock classification attempt to relate opening stability to ?stand-up time?, however, these approaches have not frequently been applied to the mining industry. Data from a ?stand-up time? graph have been interpreted in terms of an equivalent average depth of hanging wall slough and compared to the HBMS database findings. To add to the existing HBMS database, several stope case histories have been taken from Geco mine. These cases include data from very large open stopes with long exposure times. Data from all three sources suggest that hanging wall slough increases between .14 and 0.3 metres per month for a rock mass Q? value between about 4 and 13.

May 1, 2003

By D. Hamilton

The electrode of a PEM fuel cell consists of two distinct sections - the catalyst layer and the porous transport layer (PTL). There are several kinds of PTL material, although all use carbon fibres as the solid fraction. The fibres can be matted to form a paper, woven into a cloth, or chopped to form a felt. Despite the different morphologies of the media, they are all anisotropic in structure, that is the majority of continuous fibres lie perpendicular to the direction of bulk transport. Currently, no models account for anisotropy and all transport coefficients are calculated as volume weighted averages or from empirical correlations (not developed for fibrous porous media). The present work presents a new methodology for determining anisotropic transport coefficients in fibrous porous media. A numerical experimentation process is employed wherein random samples of the PTL are generated and used to solve a diffusion transport equation. Effective transport coefficients are determined by integration of flux across the domain boundaries once a steady state solution has been reached. Multiple random samples at each porosity are generated in order to predict statistical variance. The results are correlated for ease of implementation in full PEM models.

Jan 1, 2005

By G. Roy

Interest in metal-hydrogen systems can be manifold. Small amounts of hydrogen adsorbed by elemental metals and alloys usually result in strong changes in the physical and mechanical properties of engineering materials. Overwhelmingly, these changes, viz. hydrogen embrittlement, are considered deleterious with respect to structural performance of engineering materials. However, the changes, often studied by metallurgists and metal physicists, can present new possibilities and applications. A prominent example is the recent interest in safe, solid-state hydrogen storage in metallic lattices. In a new laboratory in MTL, Ottawa, a study has been initiated to investigate the effect of "micro- and macro- alloying" of Al and Mg powders with hydrogen (in high-energy mechanical alloying mills) on plastic deformation in metal and metal hydride structures. It is anticipated that high-rate impacting and subsequent grain refinement in the mill will have an effect on hydrogen storage capacity in lightweight magnesium and aluminum alloys. First examination of the state-of-stress by X-ray diffraction in high-rate milled, nanostructured pure aluminum, aluminum milled with a solid surfactant, and aluminum or magnesium alloy milled with hydride and/or gas hydrogen will be presented.

Jan 1, 2005

By Aimee Williamson

Bio-mining is a cost-effective, energy efficient and potentially environmentally protective method of exploiting a variety of ore deposits, from high-grade base metal deposits of nickel to lower-grade uranium deposits such as are found in the uraniferous quartz-pebble conglomerate beds of the Quirke Syncline, Elliot Lake, Ontario, using bacterial metabolic processes are used to enhance the solubilization of the metal(s) of interest. The cost effectiveness of bio-mining in Elliot Lake depends on the bacterially-influenced dissolution metals of economic importance, as well as on the ability to suppress microbiological activity following the release to solution of the economically important elements. This poster provides an overview of elemental recovery results and release kinetics for more than 50 elements. The data is obtained using a combination of advanced spectroscopic tools (ICPAES and ICP-MS) to analyze solutions obtained from a series of environmentally controlled biologically mediated uranium ore extraction experiments. The focus will be on rare earth elements, potential environmentally toxic elements, and metals of economic importance. Furthermore, the importance of these findings will be put into an economic and geologic context for the re-development of the mining industry of the Elliot Lake Camp.

Aug 1, 2010

By M. D. Viera

The purpose of the study is to show, through real cases of companies in Chile, the different problems concerning valuing or economically appraising a mining ore resource with the traditional techniques. The study demonstrates that, with the risk analysis and real options theory application, one could determine the most probable value for a mining resource or mining business, and the risks cover of uncertainty scenarios. The study discusses different methods and criteria employed in the ore resource evaluation or mining assets. It also shows a comparative analysis of the different methods in order to explain various distortions, errors, risks and imprecisions of each of them. the companies are becoming aware of the risks' importance and the impact they have on the commercial value and resource estimation models. Now, the real options are the techniques that somehow make it possible to value and control the risk cover of the business. The company valuation could help respond questions like: ? How much is my business worth? ? How much has the investment profitability of my business been? What could be done to improve this profitability and create value?

Jan 1, 2007

By M. Lundström

The Outotec HydroCopper® process is a novel technology, developed and registered by Outotec Technology Oy, for leaching copper from chalcopyrite using cupric chloride solution. The leaching process is operated at atmospheric pressure in a stirred tank reactor, at temperatures near the boiling point of water and pH values between 1.5 and 2.5. During the leaching of chalcopyrite in cupric chloride solution, a reaction product layer forms on the mineral surface. In the present work, the formation and the composition of the reaction product layer was studied in an environment similar to that of the HydroCopper® process. The effect of the process parameters on the reaction product layer was investigated. Electrochemical measurements, including A.C. impedance spectroscopy and microscopic observations were carried out and an equivalent circuit was used to determine the surface parameters, such as the reaction product layer capacitance and the charge transfer resistance. The results suggest that, at low pH, a passivating sulfur-rich layer forms, whereas at high pH, a more porous iron-rich layer was detected. The values measured can give useful information for optimising the leaching parameters of the HydroCopper® process. Cu2007

Jan 1, 2007

By M. Askari, M. H. Parsa, S. Kashani-Nejad

Sarcheshmeh refractory consumption rate is about 7.5 - 8 kg/ton of the produced copper, which is almost three times higher than the other smelters practice. High destruction rate of tuyere zone refractory controls vessel productivity and operational lifetime. In this research with the aid of cold model and computational fluid dynamic (CFD), melt recirculation pattern and gas - liquid plume properties in the wide range of gas blowing conditions were studied. Results revealed that in addition to the well-known mechanical refractory destruction mechanism, fast tuyere zone refractory destruction could also be related to the cold bubble cluster formation near tuyere tips and introducing severe thermal shock to the refractory surface. Removing accretion and its strong bonds to the refractories around tuyere tip, causes refractory mechanical destruction and increases tuyere diameter. Increased tuyere diameter, in turn assists gas discharge in the bubbling regime. Air blowing in the bubbling regime result in the formation of big bubble clusters, bubble breakup and back attack occurrence which all found to have major impact on the refractory lifetime. Outcomes of this research, contributed to the plant converting management, blowing hardware and instrumentation improvement.

Jan 1, 2004

By Steve R. McCutcheon, Cees R. Van Staal, John P. Langton, Leslie R. Fyffe

Abstract -The volcanic-dominated Tetagouche Group in northern New Brunswick contains numerous massive-sulfide deposits and intimately associated metalliferous sediments. The massive sulfides are generally hosted by Llanvirnian-Llandeilian volcaniclastic sedimentary rocks of the Nepisiguit Falls, Patrick Brook, and Boucher Brook formations. These formations are intercalated or closely associated with rhyolitic-dacitic flows and/or domes, and minor continental tholeiites of the Flat Landing Brook Formation. Pyroclastic rocks are relatively scarce in the silicic volcanic complex. Tuffites and epiclastic sandstones, of the Nepisiguit Falls and Patrick Brook formations, respective­ ly, generally occur along the fringes of the silicic volcanic complex. The flows and tuffites are intruded by quartz- and feldspar-phyric rhyolite (porphyry) dykes, sills, and domes. Although the volume of the silicic volcanic complex is large, evidence for a previously proposed collapsed-caldera model is lacking. On the basis of host-rock type and stratigraphic position, the sediment-hosted massive sulfides have been divided into three groups: the Brunswick-, Caribou- and Halfmile Lake-type deposits. Syngenetic feeder pipes and asociated alteration zones are generally not present beneath the Caribou- and the Halfmile Lake-type deposits and, if present at all, are poorly developed underneath the Brunswick-type.

Jan 1, 1992

The NorthMet deposit of PolyMet Mining is located in northern Minnesota, adjacent to the Iron Range. The deposit is polymetallic with values of Cu, Ni, Co, Zn, Pt, Pd and Au. The processing route selected for extraction of these values utilizes bulk sulfide flotation followed by hydrometallurgical treatment. The hydrometallurgical process has been thoroughly tested on the bench and pilot plant scale at SGS Lakefield Research. The major steps in the process are; ? Chloride-assisted total pressure oxidation for extraction of base and precious metals ?Thickening/filtration/washing of the barren residue from total oxidation ? Reduction and precipitation of Au, Pt, Pd from the oxidation solution ? Partial neutralization of autoclave acid using limestone ? Copper SXlEW for production of copper cathode ? Treatment of a portion of the raffinate from Cu SX to recover NilCo/Zn as either a mixed Ni-Co-Zn hydroxide or as separate Ni hydroxide, Co hydroxide and a Zn sulfate solution. ? Recycling of the remaining raffinate to the autoclave as coolant The process flowsheet, chemistry and bench/pilot plant test results will be reported in this paper.

Jan 1, 2007

By R. Liu

As Building Information Modeling (BIM) becomes widely adopted by the construction industry, it holds undeveloped possibilities for supporting Facility Management (FM). Some FM information systems on the market claim to address the needs for FM requirement. However, the question of whether the functionalities provided by the current BIM-based FM software companies are those actually required by the FM Professionals still need to be answered. The data is required by FM professionals in the operation and maintenance phases of facilities and type of maintainability problems that frequently occur, which can be solved early in design phase, have not yet been addressed. The aim of this paper is to clarify the frequently occurring maintainability problems and to investigate the potential areas that can use BIM technology to solve the maintenance problems in early the design phase. A survey was conducted to collect perspectives from the industry practitioners for the maintenance problems and their frequency. The survey results indicated that maintainability considerations should be taken into consideration during the facility design phase. The results also address the perceived areas by practitioners that need maintainability consideration in design phase.

Aug 1, 2013

By Bonnie Cooper

3D printing by fused deposition can be used on lunar soil. The soil can be precisely size-separated to make the 3D printing process work efficiently. Using a MASER instead of a LASER would allow us to use the finest fraction of lunar soil, AS-IS, to manufacture things on the Moon.

May 1, 2013

By I. M. Santos Moraes

The control of minor impurities (mainly As, Sb and Bi) in copper refineries has been a great challenge. Caraiba Metais' copper refinery produces a very high quality copper, registered in LME as grade A, and recognized as amongst the top ten in the copper world. At Caraiba's Tankhouse Bi and Sb are controlled by means of electrolyte bleed-stream removal after partial decopperizing in a set of electro-winning cells (liberators). Another way of reducing the Sb and Bi content in the electrolyte is by means of the arsenate precipitation chemistry. It is well known that the use of high arsenic concentrations in copper refinery electrolyte has the advantage of causing most of the bismuth and antimony to report in the anode slimes. However, the use of such mechanism of control may contribute to other undesired problems such as antimony and bismuth precipitation in the bulk of the electrolyte, what may cause severe contamination problems. This paper describes a period when some cathode contamination with Sb occurred at Caraiba Metais' Copper Refinery. It also presents an analysis of several process parameters related to the problem, the possible causes for the contaminations as well as the actions taken to correct the problem.

Jan 1, 2007

By M. Stelter

Since the first years in copper electrorefining natural products have been used as so called "additives" in the electrolyte. Glue as one of these additives offers a lot of different reactions with the metal ions and also with other additives like thiourea in the electrolyte. For a deep understanding of the effect of these additives it is important to know the routes of possible reactions in the electrolyte as well as the basics of electrocrystallization. Using this knowledge the interpretation of nodulation or inclusions of electrolyte in the cathodes in copper electrorefining is easier than before. Setting up on physical and chemical properties of the electrolyte and the additives practical investigations of the effects of additives in copper electrorefining and their impacts on copper crystallization and cathode quality are presented in this paper. Chemical deposition of glue against time and temperature are only few of the effects that are mainly caused by the use of natural products. In fact parameters like anodic and cathodic polarization are strongly affected by the additives as well as the effects of the additives are strongly affected by current density. This second part of the paper presents results concerning interactions of the above mentioned parameters.

Jan 1, 2007

By L. Byszynski

The results of a three month evaluation of the application of EMEW® technology at the KGHM Glogów II Smelter tank house bleed stream are presented. The current, conven¬tional electrolyte decopperization process has some limitations, including: only a fraction of its production is commercial grade cathode copper, significant operating costs, low current efficiency, low current densities resulting in low copper depletion rate, and arsine gas and sulphuric acid emission. The EMEW® cell technology developed by Electrometals Technologies Ltd. can overcome many of these limitations. Tests were performed on a pilot EMEW® installation comprising 30 cells at ambient temperature on electrolyte bleed, using current densities between 100 and 600 A/m2 , with copper concentrations between 45 and <1g/dm3. Results showed that a high grade copper can be obtained to the level of 7 g/dm3 of copper concentration in electrolyte. The use of EMEW® technology allows the direct and efficient recovery of over 85% of the copper contained in the bleed electrolyte. Glue & thiourea addition were tested in order to improve the parameters of the copper depletion process. The behavior of Arsenic and Bismuth was observed and a means for their elimination from the system proposed. On-line copper concentration monitoring is proposed to improve control and performance.

Jan 1, 2007

By J. L. Casado-Sánchez

Financial capital is highly volatile and if the investor does not get adequate compensation for the risk faced he may consider withdrawing his capital assets from the company and consequently produce a structural change in any sector of the economy. We study the variation in profitability of assets in terms of the changes that occur in the markets. The choice of models used is justified by the extensive theoretical and empirical use of them throughout the history of financial economics. We have used the capital asset pricing model (CAPM) and the model based on the arbitrage pricing theory (APT) to determine the beta value. These models have been applied to the monthly returns of 27 mining companies listed on the New York Stock Exchange (NYSE) or London Stock Exchange (LSE), using data from the period covered from January 2006 to December 2010. The results of time series and cross sectional regressions for CAPM and APT produce some errors, suggesting that many companies have failed to obtain an adequate cost of capital. Also the results show that higher risk firms tend to have lower profitability. These findings make it unlikely to be maintained over the long term the current status and could drive structural change in the mining sector in the form of mergers.

Aug 1, 2013

By B. Galy, L. Giraud

"This paper compares Canadian provincial mining safety regulations addressing hoist safety, automatic hoisting, and shaft obstruction. The regulations are quite similar among provinces, with only slight differences. Risk-mitigation strategies used in other industries are discussed, including their applicability to mine hoists. The specific case of software safety is introduced through examples. The mitigation of software failure is based on the use of the software lifecycle as recommended by the International Electrotechnical Commission (IEC) 61508 standard. Finally, ways to improve hoist safety are proposed.RÉSUMÉ Le présent article compare entre elles les diverses réglementations provinciales canadiennes concernant la sécurité des machines d'extraction, le levage automatisé et les obstructions dans les puits. Les réglementations sont assez semblables entre les provinces, mais elles comportent de légères différences. Les stratégies d’atténuation des risques utilisées dans d’autres industries sont abordées, incluant la possibilité de les appliquer aux treuils de mines. Le cas spécifique de sûreté des logiciels est abordé par des exemples. L’atténuation de la défaillance des logiciels est basée sur l’utilisation du cycle de vie du logiciel, comme cela est recommandé par la norme 61508 de la Commission électrotechnique internationale (CEI). Des moyens d’améliorer la sécurité des treuils sont également proposés."

Jan 1, 2016

By J. B. Evans

"THE OPPORTUNITY to participate in a CIM seminarconcerning the direction of mining engineer trainingis perhaps fortuitous as it comes at a time when theengineering schools which have invited inspection byCanadian Accreditation Board of the Canadian Councilof Professional Engineers are examining theirrespective curricula.Currently there exists considerable soul-searching in various engineering schools across Canada where questions such as the following are being posed.- Have we achieved the correct balance between subjects related to technical methodology and subjects devoted to conceptual planning and design?- Should we include ""applied humanities"" in our program? (Whatever ""applied humanities"" might mean!)- Should courses covering pollution control, ecology, economics, technical writing, professional conduct and ethics be offered as compulsory subjects, as electives, or not at all?- Is it a better scheme to have students complete an Arts or Science degree before entering engineering?- Do we place too much emphasis on pure mathematics and sciences with the result that insufficient time is available for instruction in the engineering applications of these subjects?- Should English expression and/ or literature be included in the engineering programs and, if so, should these subjects be presented by the English department or by English lecturers captive to the engineering school? - Is the present program directed primarily at research activities rather than preparing engineers for their future roles in industry? - Should we teach our own versions of mathematics and physics? - Do we have sufficient engineers on the faculty strength or are we overloaded with Ph.D.'s from the pure sciences? - How flexible should the program be, what should the compulsory vs elective course content be, and what freedom of choice, if any, should be given with respect to elective courses? - To what extent should students contribute to faculty decisions?- How far should we pursue computer science subjects and do we need to make our students proficient in computer programming? - How far should operations research and mathematical models be carried in the undergraduate program when the students have limited experience in the real engineering world? - Realizing that an engineer never completes his education, should the undergraduate program cover ""bare bones"" engineering and should instruction in particular disciplines be left to graduate schools and / or industry?"

Jan 1, 1972