Search Documents

By Serge Vézina

Environmental issues have evolved considerably over the last two decades. The main contributing factors, to name a few, have been the changing values of our modern societies, the globalization of trade and its linkage to environment, evolution and accessibility of information/communication technologies, better educated populations, climate change, long range transport of toxics and the increasing influence of NGOs and multistakeholders. As well, environmental management of mining operations had to be realigned in order to meet these new realities and to respond to more elaborated regulations oriented towards sustainability. Environmental Management Systems (EMSs) have emerged and have been introduced to meet not only the assurance of conformance to regulations but also to prevent pollution and to apply the continuous improvement of mining processes. EMS models have been developed and certification to international standards (e.g. ISO-14 001) is a common practice. Globalization has imposed challenges and additional requirements to environmental management. Developing a mine in emerging countries implies dealing with international agencies, local communities and a variety of government infrastructures to obtain a ?licence to operate?. This paper presents the structure of our EMS and how we have adapted its implementation to our operations in South America.

May 1, 2003

By W. Zieman

"The low consumption of reagents can probably be attributed to a good clean type of ore. The cyanide level is kept at 0. 8 lb/ ton of solution and the lime at 1. 8 to 1.9 lb per ton of solution (pH 12. 2 to 12 .3). Experience in cutting down the lime level in half produced troubles in the presses, in the refinery and resulted in higher cyanide consumption. Finally the residue increased under these conditions, High lime always seems to prevent the trouble from occurring.A survey at one mine of the taxable work, performed in the mine shops for use in the mine, showed that under the new regulations, this had increased some 30 times what it was before the new rules came into effect on June 14, 1963.A water softener idea is incorporated at Lamaque with the crude addition of 100 lb of lime per shift to a spare agitator to precipitate the bicarbonates as carbonates from the water before it enters the mill. The lime titration of the softened water is about 0,2 to 0.3 lb per ton of solution (pH 11). This water is used mainly on the filters as washes."

Jan 1, 1964

By B. Grinbaum

The solvent extraction of Cu from acidic leach solutions is carried out using oxime extractants. The mechanism can be described as liquid ion exchange, where a labile H+ in the oxime replaces Cu++ ion from the pregnant leach solution. The process is reversible and, at high acidity, the copper is stripped back to the aqueous phase. As the extraction proceeds, the acidity of the aqueous phase increases and the equilibrium may shift against the extraction reaction. This phenomenon may become significant in leach solutions with high copper concentration, where large amounts of acid are transferred from the solvent into the aqueous phase. An efficient way to increase the recovery of copper consists of splitting the extraction into two circuits, and either neutralizing with lime or extracting the excess acid of the intermediate raffinate. In the second case, the acid can extracted using a solvent, which can be stripped with a base, e.g., NaOH or ammonia. A third option is direct neutralization with soluble basic salt, e.g., Na2CO3, within a single extraction battery. The choice of the preferred process depends on the specific process demands and on the relative availability and price of the raw materials and by-products price.

Jan 1, 2007

By P. W. Ware

The majority of all refined copper is consumed to produce electrical conductors. Most copper conductors are drawn into wire from 8 mm ETP copper rod produced from high purity copper cathodes. Southwire Company has more than 40 years experience using, designing, fabricating and marketing a process for continuously producing ETP copper wire rod. This process is called the SCR® (Southwire Continuous Rod) process. Today, approximately half the copper wire rod produced in the world, or more than one third of all refined copper consumed, is produced using the SCR process. Southwire has sold 75 SCR copper rod mills to metal producers and wire manufacturers around the world. Southwire is North America's largest electrical wire and cable producer. Southwire operates a 48 metric ton per hour SCR® copper rod system in Carrollton, Georgia. This allows Southwire to provide technical support for existing SCR® system customers based on first-hand knowledge. Rod fabricators and their wire customers are always striving for copper rod that improves productivity. They are looking for improved surface quality, finer wire sizes and fewer wire breaks per ton of rod drawn. This paper will present a brief history of the SCR® process, a description and recent process developments.

Jan 1, 2007

By E. Rezaei

Glue is an animal protein that is used with other organic agent such as thiourea, in copper electrorefining. The concentration of glue has to be controlled carefully, because the electro-deposition process is often very sensitive to small fluctuation in the operating variable. This additive (glue) prevents rough and nodular copper cathode deposits. The nodular deposits may grow causing short circuits, which results in losses in production. Addition agents are effective in controlling metal growth; they modify the normal nucleation and lattice growth steps and refine the grain structure. In this research glue concentration was determined in an industrial copper electrolysis plant. A non-linear model with high capability was constructed and after optimizing its parameters, the accuracy and precision of the model were evaluated. For determination of glue concentration, electrochemical voltammograms in optimum condition (Differential pulse voltammetry technique, Hpulse=50 my, scan rate=10 mv/s) were plotted. Some information from voltammograms was transferred to the model as inputs and the calibrated model analyzed the information and the glue concentration was determined with high precision and accuracy. In this way there is no need to separate or add agents to remove interferences. This method has been successfully applied at Sarcheshmeh copper complex.

Jan 1, 2007

By R. Ichimura

This paper summarizes the results of a five-year project, which aimed at improving the current method to process the arsenic-bearing smelter dust of El Teniente. This project, which was started in 2001, was carried out jointly by JOGMEC (Japan Oil, Gas and Metals National Corporation) and CIMM (Centro de Investigación Minera y Metalurgica, Chile), and was financially supported by the Japanese and the Chilean governments. In the new process, the smelter dust is leached with sulfuric acid to dissolve arsenic, which is subsequently precipitated as crystalline ferric arsenate (scorodite) at ambient pressure by controlling the crystallization and crystal growing stage. As a result, a stable form of ferric arsenate is obtained, which passes the U.S. E.P.A. TCLP limit of 5 mg/L As. Copper and zinc are subsequently recovered from the arsenic-free solution. The copper product can be fed into the main copper production circuit at the Las Ventanas Smelter and Refinery, whereas zinc is recovered as a marketable product. A demonstration plant was installed and operated at CODELCO's Las Ventanas Smelter and Refinery. The basic and detailed engineering design was prepared by Mitsui Mining and Smelting Co. Ltd (MMS) on the basis of a joint study done by JOGMEC, CIMM and CODELCO's Las Ventanas Division.

Jan 1, 2007

By Masafumi Maeda

Metal recycling and waste treatment have become common issues in various metal industries, notably, the iron and steelmaking industry and the nonferrous industry. The former tends to treat mass wastes such as municipal wastes or plastics. However, volatile compounds are condensed in dusts of their incineration processes and they should also be treated, likely by the nonferrous industry. Those "end-of-life" products contain heavy metals that might be harmful to mankind and should be handled by the non-ferrous industry. Not only revenue derived from regeneration of metals from the secondary materials but also the revenue generated from the treatment charges is a strong attraction for nonferrous industry to process secondary materials. The present study presents some statistical data of the Japanese corporations in the iron and steelmaking industry as well as the nonferrous industry on their revenues generated from processing of secondary materials. Some of the companies are now concentrating their business resources on new areas of the market. Although the quantity of waste or recyclable material is still small at present, the quantity will increase in the near future, and it is anticipated that international collaboration is required to handle the greater variety and the larger quantity of secondary materials.

Jan 1, 2004

By Jerry Z. Lu

Belt conveyor design involves the evaluation of belt tensions, drive selection, pulley configuration and other technical issues. The conveyor belt tensions vary with conveyor layout, drive pulley configuration, belt selection, and idler selection. The decisions for the belt conveyor construction always take all technical, commercial and maintenance issues into consideration. A good conveyor design shall provide required operational features and at the same time be cost effective. The common issues for an engineer to face during belt conveyor design include: (1) Conveyor drive selection ? drive with fluid couplings or variable frequency drives; (2) Drive system configurations - single pulley large drives or dual pulley smaller drives, if intermediate tripper booster drives shall be applied, what power ratio should be adopted for a multi-drive conveyor; (3) Gear reducers ? shaft mount drives, right angle gear reducers or parallel gear reducers; (4) Drive pulley lagging - ceramic lagging or rubber lagging; If ceramic lagging, what type should be used. (5) Conveyor speed variation ? If conveyors run at variable speeds, faster speed/lower percentage loading or slower speed/higher percentage loading. In many cases the decision maker find themselves in a dilemma ? technical benefits vs. financial benefits, capital cost vs. operational cost, and capital and operational cost vs. maintenance effort. Although many conveyor design topics above have been discussed in numerous technical papers and design reference books, management executives and inexperienced engineers may be confused and feel lost. The consultation of people around them may lead to different opinions since experiences tend to vary, making the decision making process complicated. The purpose of this paper is to simplify these complicated issues and provide useful guidelines for belt conveyor design. This paper focuses more on providing simple and practical answers and solutions instead of discussing each topic academically and theoretically in depth.

Nov 1, 2011

By J. Chlan

"Dryer DescriptionProctor and Schwartz Continuous Conveyor DryerThe Proctor and Schwartz Continuous Conveyor Dryer has been in operation since July 1958, and comprises six unit• - an 8• wide single conveyor with roller extruder, insulated housing, type 304 stainless steel circulating and exhaust fall system, steam heating coils, temperature controls and discharge crusher rolls. Entire dryer dimensions are 52’ x 12'0""weighing 53,000 lbs,Extruder rolls - setting is 1/8"" (Drive 3 HP 1800 RPM) clearance off the extruder screen.Conveyor - consists of 151 interlocking pans, measuring 8"" x 8' (2 HP 1200 RPM) One Exhaust Fan (5HP - 900 RPM)Steam Coils -- l"" steel pipe - with steel fins -- each coil measures 16' 2’’- 64 coils in the No, 1 Compartment- 64 coils in the No, 2 CompartmentDryer OperationThe yellowcake slurry at 28% solids is pumped to an 81 x 8' Peterson Filter. The filter media presently being used is a Neotex 4372 blanket, being 100% staple fibre nylon, 12 oz per square yard with air porosity of 9 CFM's. The cake discharge at 45 - 50% moisture falls into the roller extruder. Extrusions are formed by forcing the material by rolls through a perforated plate moving back and forth and depositing the spaghetti-like extrusion on onto the dryer-conveyor.The conveyor now carries the extruded material through the heating chamber•, The feed end of the dryer will be referred to as No. 1 Compartment, with temperature control set at 280""F. The circulating fans take the hot air off the coils and circulate the heated air through the perforated openings in the dryer conveyor pane, After passing through the set of steam coils and circulating fan in No, 1 Compartment, the material then goes through No, 2 Compartment where the temperature is set at 305'F, Final material then discharges through a set of crusher rolls set at ~"". Moisture of final dried product runs at less than 2%.The dryer conveyor load is usually run to a 3"" - 4"" depth load. Conveyor speed at approximately 90 minutes for load to pass through. Load onto the conveyor is controlled by boot level and speed of the 8' x 8' filter. The dryer steam coils are water-washed twice a month."

Jan 1, 1972

By T. T. Chen

A detailed mineralogical study was carried out to characterize the products generated in a conventional copper refinery anode slimes treatment circuit. The anode slimes, which are first leached in sulphuric acid media under an oxygen pressure to dissolve the copper and much of the tellurium, were found to contain various Ag-Cu selenides, PbSO4, Ag, Au and BaSO4. The resulting Ag2Se, Ag3AuSe2, Se, Au, PbSO4, BaSO4, SnO2 and silicate-rich leach residue is dried and pelletized. It is subsequently roasted to convert the selenium to Ag2SeO3, volatile SeO2 and water soluble Na2SeO4. The roasted product, which was found to consist of Ag2Se, PbSe, PbSO4, BaSO4, Ag3AuSe2, Au and Sn02, is smelted and refined in a Dore furnace to produce a Dore metal that contains a (Ag,Au,Pd,Cu,Pt) alloy together with traces of CuO and a Cu-Pb oxide phase. Parting plant mud shown to contain AgC1, Ag, Au, (Au,Ag,Pd), Ag2Cu2O3 and Ag20, and scrubber mud containing PbSO4 and AgC1 are also fed to the Dore furnace. The Dore furnace sequentially separates a silica slag which was found to consist of Ag, Sn02, BaSO4, Pb-Sb oxide, Fe-Sb-Ni-Cr oxide and a Pb-rich silicate phase, a soda-rich slag containing Na2CO3.H2O and Na2(Se,Te)03, and a niter slag containing Na2TeO3, Na2(Se,Te)03 and a Na-Te-Se-Pb-Ba-Cu oxide phase. The Dore metal is electrorefined in Moebius cells to yield high-purity silver and a gold mud which was shown to consist of a (Au,Ag,Pd,Cu,Pt) alloy and traces of CuO. Silver is leached from the gold mud and the resulting gold sand is cast into anodes and electrorefined in Wohlwill cells to produce pure gold.

Jan 1, 2007

By Jr. Wilkinson

Suncor Energy currently mines approximately nine hundred thousand tonnes of ore and waste per day at its open pit operations in the Athabasca Oilsands near Fort McMurray, Alberta. Modeling these deposits for planning purposes is particularly challenging given the characteristics associated with the deposit - stratigraphic deposition coupled with gradational grade distribution. The identification of ore and waste is a combination of bitumen cutoff grade, minimum mining thickness and separable waste thickness subject to criteria established by provincial regulatory agencies. Suncor along with Mincom Inc. have collaborated on this project to derive a methodology, automated by computer software, to streamline the ore and waste identification process. This paper explains the methodology and programs created to identify ore and waste in use at Suncor Energy and how this identification is used to categorize reserves and to generate mine design surfaces.

Apr 1, 2005

By M. Solomon

Giant, sediment-hosted lead-zinc deposits in northern Australia fonned during development of Mid-Proterozoic extensional basins that overlie Lower Proterozoic basement. The basement in the Mount Isa area, exposed by folding and faulting, contains fractionated, high-heat-producing granites. These granites generate heat at a rate of about 6",Wm-3, probably sufficient to fonn giant lead-zinc deposits either by (a) driving episodic convection of saline basement and basin fluids for periods of IOS to 106 years at temperatures of about 230°C, or (b) heating basin fluids moving under the influence of topographic relief or fault movement. The presence or absence of such granites may form a vital component of the genetic model. Ore-fonning fluid flow was probably initiated by continent-scale, extensional basin fracturing.

Jan 1, 1992

By S. Brophy

Controlled Short Circuit ? Metal Inert Gas (CSC-MIG) welding is a process that can be referred as a "Cold Welding" technology. The CSC process is based on accurate control of the welding wire position, thus the mandatory requirement for the automation of the process. One of the main advantages of the CSC-MIG process is the rapid solidification of the deposited material, resulting in weldments displaying low porosity contents, and enabling the joining of thin sheet materials. These characteristics render this process an ideal one for freeforming of components, where rapid solidification would be efficacious. This presentation will focus on the progress made towards the freeforming of Al-based components in the NAIN laboratory at McGill University. The relationship between the filler metal used, freeforming (deposition) parameters, resulting microstructure and mechanical properties will be presented.

Jan 1, 2011

By S. Kamado

Development of new SF6 alternative cover gas with low global warming potential is strongly desired for melting and casting of magnesium alloys. We have tried to apply several kinds of HFC and HFE gases with low potential from 30 to 950 as protection gases to AZ91D alloy melt in the temperature range of 650 to 800°C. As a result, protective film consisted of MgF2 and MgO is formed on the melt surface and ignition-proof effect is sufficiently obtained at all the temperature ranges even when flow rates of mixed gases containing CO2 as a carrier gas are almost the same as those using SF6 gas. Reduction of global warming potential exceeds 98% at 650°C and 89% at 800°C in comparison with a mixed gas of CO2 and SF6.

Jan 1, 2006

By J. Baumbach, H. Bombach, M. Stelter

"Today technical electro-refining processes for copper exclusively use sulfuric acid, for silver refining nitric acid electrolytes are used. Sulfuric acid is characterized by very good chemical and electrochemical stability, good conductivity and low cost. The disadvantages of sulfuric acid are the precipitation of fine-grained cathodes with smooth surfaces only by using additives like glue, thiourea and chloride. In case of silver the electrolyte is electrochemical unstable and bears the risk of the formation of toxic NOx when pH is too low. A second disadvantage is the form of electrodeposition of silver as dendrites with their removal from the bottom of the Möbius cells.This paper reports the results concerning the application of an alternative electrolyte in copper and silver electro-refining. At first the electrolyte was characterized by the determination of current density potential curves. Electrolysis experiments were performed in laboratory scale using technical anodes for copper and synthetic anodes for silver. During the copper tests the solubility of contaminations from the anodes and the amount and chemical composition of the anode slimes were determined. Moreover the influence of current density, electrolyte temperature and the effect of several additives on the precipitation and chemical purity of the cathodes were investigated. In all experiments cell voltage as well as anodic and cathodic polarization was measured and current efficiency and specific energy consumption were calculated. A comparison with the results with those of tests using conventional sulfuric acid electrolyte shows the advantages and disadvantages of both systems, additionally the technical application chances and limitations for the new electrolyte. This electrolyte enables the precipitation of smooth copper cathodes with low silver and sulfur concentrations even at lower temperatures without any additive. For silver refining the electrodeposition of compact silver sheets is possible, that can be stripped comparable to those in copper electro-refining."

Jan 1, 2016

By J. Vanderlaan

A proposed method of applying high-speed, non-destructive part scanning technologies to the production process of UO2 (Uranium Dioxide) fuel pellets is presented. The scanning process examines each pellet individually for correct surface roughness and any surface imperfection or defects. Using optical scanning methods, which consist of laser and CCD camera technology, the complete circumferential surface of the pellet is examined to meet the reactor fuel bundle specifications.

Aug 1, 2010

By M. Xian, M. Jahazi, Y. L. Lin

The 2-mm butt joints of ZE41A-T5 sand castings were laser welded at different defocusing distances on two surface conditions (as-cast or machined) using a continuous wave 4 kW Nd:YAG laser system at a power of 2.5 kW and a welding speed of 6.0 m/min. Two welding modes (conduction or keyhole) have been observed. The adjustment of defocusing distance can greatly influence the establishment of conduction or keyhole modes. On the machined surface conditions conduction welding is obtained at a power density of 4.0 x 105 W/cm2. In contrast, keyhole welding is reached at a threshold irradiance of 1.5 x 106 W/cm2. Neither conduction nor stable keyhole modes have been established at a range of power density from 7.7 x 105 to 1.2 x 106 W/cm2 on the machined surface conditions. On the as-cast surface conditions keyhole is obtained at a power density as low as 4.0 x 105 W/cm2 but good surface quality is obtained at a defocusing of +2 mm. The as-cast surfaces require lower power irradiance for the formation of keyholes indicating that they have higher energy absorptivity for Nd:YAG laser beams probably due to coarse surface morphology.

Jan 1, 2004

By T. Cutard, E. Cailleux, F. Nazaret, G. Bernhart

This paper deals with the study of the mechanical behavior in the 20°C-900°C temperature range of refractory concretes reinforced with metallic fibers. Fibers are introduced to improve the damage resistance and to minimize the quasi-brittle behavior of refractory concretes. In some cases, a plastic or ductile like behavior can be obtained. Two approaches are considered in these studies. The first one is based on the micromechanical scale. Main objectives are to understand, quantify and predict the thermomechanical behavior of monofiber microcomposites. Such considerations are helpful to optimize the composite formulation for a better behavior. The second one is based on the macromechanical scale. Main objectives are to characterize and to model the macroscopic thermomechanical behavior of randomly reinforced refractory concretes. A particular attention is firstly paid to the relationships between the microstructural changes and the mechanical properties and secondly to the structural size effects.

Jan 1, 2004

By Xiao Huang, Jean-Francois Thibault, Ali Merati, Prakash C. Patnaik

Single-crystal nickel-based superalloys are the current state-of-the-art technology for the manufacture of turbine blades. This technological improvement of the turbine blade has brought a considerable increase in its cost. Repair and overhaul of service stressed single crystal turbine components is an economic necessity for life cycle cost reduction of engines since the cost associated with replacement is significantly higher than its counterpart polycrystalline component. This paper will first review the recently reported research in developing repair technologies used for DS and SX components. These techniques repair the crack or defect while at the same time ensuring that the mechanical properties do not deteriorate and, more importantly, that the single-crystal microstructure is not jeopardized. It will then be followed by a brief overview of the research conducted and initiated by the authors with regards to the repair of single crystal alloys.

Jan 1, 2004

By Fathi Habashi

This Historical Metallurgy Note is the final part of a three-part series, the first two of which appeared in the November- December, 1997 and January, 1998 issues of the Bulletin. This series of articles is dedicated to the memory of Nikolai Maximovitch Pereskuryakov (1940- 1994), Rector of Saint Petersburg Mining Institute from 1992 to 1994 who passed away unexpectedly at the age of 54, shortly after celebrating the 275th Anniversary of the Institute.

Feb 1, 1998