Search Documents

By N. Giguère

Until recently, the heat treatment of pressure die cast parts has always been considered unpractical because the solution heat treatment resulted in unacceptable blistered parts. This was due to the presence of massive porosity associated with the die casting process where the inflow of metal inside the mold cavity is extremely turbulent. With the steady improvement of foundry practices and the generalization of vacuum die casting, porosity defects have been reduced to the point that a partial solutionizing heat treatment can be applied without any damage to the casting. However the solutionizing temperature must be lower than that applied to macroporosity free castings and for much shorter time. The object of the present study was to determine the optimum solutionizing temperature that can be applied to aluminum 383 die cast brackets along with the optimal temperature and time of aging resulting in the highest improvement in mechanical properties (both strength and ductility). This was done by testing strength and deformation on the casting itself using a specially designed jig; the crushing force to deformation curve was analyzed so as to quantify the improvement in both strength and ductility gained with the partial precipitation hardening heat treatment.

Jan 1, 2011

By D. Runnels, A. Allaire, J. Fournier, Y. Sylvestre, F. Robichaud

The Goldex operation of Agnico-Eagle Mines (AEM) commenced operations in the spring of 2008. Following some months of initial operation, the grinding circuit capacity was under-performing according to the original design throughput. BBA Inc. (BBA) was commissioned, in February 2009, to study the different options and recommend the quickest and most cost-effective solution to increase the grinding circuit throughput rate. The mandate was to increase the throughput of the grinding circuit to beyond the original design of 7,000 tpd to 8,000 tpd or greater, while retaining the existing SAG and ball mills. The circuit was modelled using JKSimMet software to evaluate the different options, each with a number of different operating parameters. The option of secondary crushing of the SAG mill feed was retained. Comparison of the different options and simulation outcomes, design of the secondary crushing circuit, operating conditions, and initial adjustments in the design and operating results of the new grinding circuit are discussed in this paper.

Jan 1, 2012

By Wei Huang, Anh V. Nguyen

"Potash flotation is an industrially proven success of flotation of soluble salts, but its collector adsorption mechanism remains elusive. In this paper, specific ion effects in NaCl-KCl flotation with carboxylate collectors were investigated. Flotation recovery and contact angle were determined as a function of brine composition of NaCl and KCl. The experimental results have shown that wettability of KCl and flotation of the soluble salts with laurate collectors were dependent on brine ion composition. Specifically, adding Na+ to brines decreased hydrophobicity of KCl crystals and their flotation recovery. Both KCl and NaCl could be floated with laurate collectors. However, flotation of NaCl was greatly enhanced by adding K+ to brine whereas flotation of KCl was significantly suppressed by the presence of Na ions. The decrease in KCl recovery upon adding Na+ is attributed to the counter-ion binding in the pulp. The flotation recovery enhancement of NaCl in the presence of K+ is explained by two effects: 1) increasing K+ concentration leads to a better dispersion of collector colloids in the pulp and 2) K+ enhances the collector adsorption at NaCl crystal surfaces. The water affinity matching rule can explain the specific ion binding behaviors and supported by the SFG spectroscopic results.INTRODUCTIONPotassium is an important fertilizer. Its primary source comes from potash ores, which are a mixture of sylvite (KCl), halite (NaCl) and many other complex double salts such as carnallite (KCl·MgCl·6H2O), alkali nitrates such as KNO3 and NaNO3, and sulfates-langbeinite (2MgSO4·K2SO4) with water-insoluble minerals such as clay and carbonate minerals. Previously, these salts were recovered with a lengthy hot leaching method, with further crystallization of potassium salts from saturated saline solutions. Selective flotation has been preferred since 1940s. Various collector adsorption mechanisms have been proposed soon after the industrial introduction of potash flotation. These include the formation of the insoluble compound model (Halbich, 1933; Singewald, 1961), an ion exchange model (Fuerstenau and Fuerstenau, 1956), a heat of solution model (Rogers, 1957), the surface hydration model (Schubert, 1988), the surface charge model (Roman, 1966; Miller et al., 1992), the interfacial water structure model (Hancer and Miller, 2000) and the colloid adsorption model (Leja, 1983; Burdukova and Laskowski, 2009). Most of the early exercises attempting to propose a unified rule on collector adsorption mechanisms can be seen as heroic endeavors due to the consideration of a vast number of salts in the pulp including alkali halides, nitrates, and sulfates, even the practically insoluble heavy earth metals. Additionally, several types of surfactants with different polarization features and alkyl chain length have been employed. As for the recent models, due probably to the preferential application of long chain amines as collectors in industrial potash flotation, most researchers are only devoted to collectors with low polarization features like amines and sulfonates (Hancer and Miller, 2000; Du et al., 2014). Collector adsorption mechanisms are therefore proposed based largely on a neglect of carboxylates as collectors. However, carboxylates remain an important collector type in soluble salt flotation systems where both salt minerals can be floated using anionic collectors and cationic collectors. Fatty acid type collectors are still one of the widely used collectors for soluble salt flotation and also one of the first to be applied on an industrial scale for the separation of potash ore (Hernáinz et al., 2003; Titkov, 2004). Here we examine some recent models that are relevant to our study to reveal a long neglected specific ion binding effects in potash flotation."

Jan 1, 2016

By David L. Sprott

This paper presents an evaluation of underground-to-surface haulage options for a relatively large deposit. Specifically, it presents a recommended haulage option to provide the greatest value to the Project. Options considered included conventional truck, trolley-truck, conveying and shaft hoisting. The work was done at the level of a preliminary assessment as input to an internal pre-feasibility study. The Base Case for the analysis in this study was a Long Hole Open Stoping option (LHOS) using conventional truck haulage. Two scenarios were considered for the evaluation and included: 1. The current resource to ~700 m depth. 2. An expanded resource to ~825 m depth. The haulage options evaluated included three trucking options, three conveyor options and two shaft options. The paper presents the results from evaluating these options within the two mining scenarios using a Discounted Project Cost (DPC) comparison. Recommendations are made for the options that will provide the greatest overall value to the project.

May 1, 2008

By L. Jacobsson, J. E. Lindqvist

A series of laboratory tests were conducted to study stress-induced spalling on medium to coarse-grained granite specimens. The specimens made from cylinders had two manufactured notches on opposite sides aimed to represent the tangential loading around a circular opening. Specimens of three different sizes were tested with notch radii, 98.5, 225 and 375 mm, representing 197, 450 and 750 mm diameter holes, to study the effect of notch radius on the spalling initiation stress. The cracking was monitored by acoustic emission sampling. The fracture patterns were investigated visually on polished slabs and by microscopy on thin sections. The crack analysis describes how the cracks propagate in relation to the grain structure in the rock and to the macroscopic stress field.

Jan 1, 2015

By M. S. Ünal

Creation of 3D model of coal seams is a tedious and time consuming operation. Computer aided 3D solid modelling of coal seams can be performed in a fast and detailed manner. However, in case of having tectonically disturbed coal seams where faults may be observed, expert opinion is necessary to decide the geometry of the coal seam. The aim of this study is detection of fault zones with computers by using drill hole data. Firstly, a digital database is generated by using the drill hole data. Surface models of the layers are produced by applying triangulation method on coal seam roof elevations. The generated surface is divided into small squares and consequently dip and dip direction values are calculated for each square. Variograms for dip and dip direction are determined and maps showing the variation of dip and dip direction are generated by using geostatistical methods such as kriging and co-kriging. Examination of disconformities observed on estimation maps created by kriging and co-kriging clearly reveals the extension of faults. The method used in this study is applied to detect fault lines of a known mine field. 3D solid modelling of the coal seam has also been performed by using conventional cross-section method. The results of both methods were in good agreement. Identification of major faults by using the method introduced in this study could certainly simplify 3D solid modelling of coal seams.

Aug 1, 2013

By A. J. Russell

"This paper investigates why it is critical for a mine to accurately determine thermal rock properties and virgin rock temperatures. Theoretical simulations of deep mining production zones have demonstrated that thermal conductivity (k), virgin rock temperatures and specific heat (cp) significantly impact rock heat predictions which can be the dominant component of a mine’s heat load. Natural variability in these factors showed that realistic errors can have a significant effect on mine heat loads. This can ultimately affect miner safety and introduces risk to the viability and sustainability of a project. INTRODUCTION Accurate heat load determinations are critical to ensure that underground working conditions are maintained within legislated and mine specific parameters to safeguard the safety and productivity of employees. Underpredicting mine heat loads will result in hot underground conditions, which risk the health and safety of employees, reduce the productivity of employees or stop production if legislated temperatures in working areas are exceeded. Overestimating mine heat loads will result in increased capital and operating costs reducing the viability of the project. Over- or under- predicting the heat load for a project will increase the project risk. Heat sources in a mine can broadly be broken into two categories. These two categories are defined by Hemp and Rawlins (2014) as natural and artificial heat sources. Those sources which depend on the size, location and depth of the mining areas are defined as natural heat sources, whereas those heat sources which are a result of the actual mining activities are defined as artificial heat sources. Autocompression, or the conversion of potential energy, to enthalpy is an important consideration when determining the air temperature in the mine and its interaction with natural and artificial heat sources. It is documented by Jones (1985) and Hemp and Rawlins (2014), that the heat flow from rock in deep mines can dominate other heat sources; information from BBE’s archives show that this is between 40% and 60% of the total heat load. They also point out the importance of accurately measuring both the thermal rock properties and virgin rock temperatures (VRTs) for determining and planning the ventilation and refrigeration requirements for a mine. Both of these texts cite multiple methods for calculating the heat-flux and ultimately the heat load for the different working areas in a mine. All of these methods demonstrate that the heat flux and heat load will increase proportionally with increased thermal conductivity (k), specific heat (cp) of the rock or mineral, and VRT depending the area of the mine or mining method."

Jan 1, 2019

By Robert K. Jonas

Mining companies can improve production and reduce costs by using the best available technology to control their operations. Many mines are challenged to use multivariable predictive control due to limited experience or staffing, as well as being concerned over the robustness and sustainability of predictive controls. As a result many mines are not realizing optimal performance from their assets, and thusly are not realizing the production increases or cost reductions that this technology can deliver. Over the past few years, the application of multivariable model-based predictive control has gained acceptance in many mining processes and has proven to be robust and sustainable for some of the most challenging mining processes. New automated modeling and performance monitoring software have greatly simplified the effort to implement and maintain these solutions. In addition, many progressive companies have chosen to co-source the implementation and service of these solutions to assure project success and continued benefits stream. This technology has been successfully applied to a wide variety of processes; grinding mills, alumina digestion, CCD washer and thickeners, kilns, calciners, roasters, flash smelters, heat exchangers, evaporators, and most recently in the demanding process of flotation. This paper discusses the state-of-the art in advance control technologies in the mining industry, including the impact of these technologies on maximizing benefits, and implementing best practices for long term sustainability. Benefits from recent multivariable predictive control applications in copper mining will be reviewed, and the use of the latest predictive control technologies and practices in mining will be discussed.

Oct 1, 2009

By G. D. Hibbard

New regions of material property space can be accessed by combining microstructural design at the nm-scale with architectural design at the µm- or mm-scale. In the first case, large strength increases associated with grain size reduction to below 50 nm have driven extensive research efforts into the development of nanocrystalline materials [e.g. 1-3]. For many potential structural applications, however, the density of a nanocrystalline material is just as important as its strength. In fact, reducing the density is more important than increasing the strength for certain weight specific materials performance indices, and it is especially critical for applying structural nanomaterials in the aerospace and automotive sectors. We have developed a new type of structural nanomaterial wherein the effective density of the parent metal is reduced by more than an order of magnitude by incorporating an internal periodic cellular architecture of open space. In one example a low density cellular nanocrystalline material was created by electroforming nanocrystalline Ni around a rapid-prototyped acrylic photopolymer microtruss, Figure 1 [4]. Microtruss materials have periodic cellular architectures that are specifically designed to undergo stretching-dominated deformation as opposed to the bending-dominated deformation in conventional open cell metal foams [5,6]. This new cellular nanocrystalline hybrid material combined the structural efficiency of microtruss architectures with the ultra-high strength that can be achieved by grain size reduction to the nm-scale. Although it played a critical role as a cathode support during the initial stages of nanocrystalline electrodeposition, the polymer core did not contribute significantly to the inelastic buckling resistance of the composite metal/polymer struts and it may therefore be desirable to remove it post deposition by means of chemical dissolution or thermal decomposition [4]. Nanocrystalline electrodeposition can also be used to reinforce conventional cellular metals (Figure 2), creating new types of cellular composites such as metal/metal microtruss hybrids [7-10] and metal/metal foam hybrids [11,12]. For example, nanocrystalline Ni-Fe alloy sleeve thicknesses of up to 400 µm were used to reinforce an aluminum alloy microtruss that had been fabricated using a stretch-bend approach; the nanocrystalline sleeves had the effect of increasing the microtruss strength by up to a factor of twelve and the specific strength by a factor of three [8]. Alternatively, much thinner sleeves can be electroplated to produce structural coatings. In one example, a nanocrystalline Ni coating was designed to provide both corrosion protection and inelastic buckling resistance [10]. Because the ultra-high strength material was optimally located at the furthest distance from the neutral bending axis, only a thin coating of 50 µm was needed to double the inelastic buckling resistance of the 1.13 mm x 0.63 mm cross-section plain carbon steel struts [10]. Overall, the mechanical performance increase that can be obtained through electrodeposition depends on a complex interaction between the starting cellular architecture and the nanocrystalline sleeves.

Jan 1, 2010

By M. Cimenti

Fuel cells have tremendous potential as power sources but much fundamental research is still required. One key component of the research is the experimental set-up used. In particular, the placement of the reference electrode is extremely significant in measuring the half-cell overpotential of solid oxide fuel cells, since differences in area, misalignments, and also differences in the kinetics of the working and counter electrodes can cause both scaling errors and frequency distortions of the measured impedance. The impedance of thin solid electrolyte cells of different electrode geometries has been calculated using the finite element method and the results compared to experimental values obtained for the oxygen reduction reaction on platinum.

Jan 1, 2005

By Sudarshan Martins

The measurement of acoustic signals produced by a tumbling mill has been previously used to determine the operating state of the mill and correlate the variations of the sound intensity with the operating conditions of the mill. Separately, the discrete element model (DEM), a software simulation of the mill, was developed to provide insight into the operation of the mill. Presently, there has not been much work reconciling the DEM simulation of the mill with the acoustic signal. Working from basic principles of linear, time-invariant systems, agreement between an acoustic DEM simulation and the measured signal is sought. First, the impulse response function of the mill is measured. The DEM provides the forces applied to the mill shell as a function of time. A convolution of these simulated shell forces and the transfer function gives the simulated acoustic signal. This signal is compared to the measured acoustic signal, both in the time domain and the frequency domain. Finally, a discussion of the results is given.

Jan 1, 2012

Presentation Overview ?WRDC Purpose and Activities ?Women in Trades, Technology and Operations (TTO) Occupations ?Factors in Successful Recruitment / Retention of women (VBNC) ?Recruitment and Retention Strategies ?Conclusion Women in Resource Development Committee (WRDC) ?Incorporated in 1999 as a Not for Profit Organization ?Based in Newfoundland and Labrador ?Works to Increase the Participation of Women in Natural Resource Industries ?Research (Using Gender-Based Analysis) ?Career Exploration Programs for Women and Girls ?Outreach and Advocacy ?Policy Development ?Public Awareness and Education ?Gender Sensitivity Training ?WRDC Educational Resource Centre

May 1, 2006

By Q. J. Xu

In blasting sensitive areas, the use of traditional blasting for rock fracture is restricted. Soundless cracking technology has been presented to achieve rock fracture instead of blasting. However, when the diameter of a borehole is larger than 50 mm, it is very dangerous that the soundless cracking agent (SCA) will have a tendency to gush from the borehole, which also leads to cracking failure. In this paper, a new large scale borehole soundless cracking technology is presented, using a new enlarged drill bit and mechanical plugging, which could solve the hole gush problem. Experiments were made to measure the expansive pressure of the SCA working in boreholes of F40 mm and F100 mm. The difference between two sizes of cracking phenomenon was compared and analyzed to show that large scale borehole soundless cracking has larger expansion pressure and faster reaction speed than traditional soundless cracking. Based on the experimental data, finite element analysis was utilized to study the stress concentration and stress distribution between two neighboring large boreholes in several media during the cracking process. Using the data from experiments with finite element numerical simulation, the brittle material fracture condition was analyzed to design the parameters of the borehole mesh. With the theoretical analysis, the technological process and reference parameters of large scale borehole soundless cracking were proposed, including the borehole spacing, burden distance, depth of the borehole and so on. Then a single rock was cracked with the new enlarged drill bit and new plugging, and the results proved the feasibility of the new large scale borehole soundless cracking technology, which achieved the expected goal of improving the cracking ability and reducing the cracking time. This paper presents a new efficient rock cracking method for blasting sensitive areas, and which could apply to mining engineering, demolition engineering, excavation engineering and other engineering applications where there is a demand soundless and non-vibration fracturing of rock.

Aug 1, 2013

By Frank Wright

"The Icon Sullivan Joint Venture ore deposit was discovered in June, 1965 by Messrs. Paul Benard, Bob Galipeau and Mac Watson working under the direction of Mr. Andrew J. Troop, as employees of the Icon syndicate. The deposit is located on the Waconichici River as the south end of Baie du Poste of Lake Mistassini, approximately 45 miles north of Chibougamau. Property acquisition and Winkie drilling was followed by a diamond drilling program to evaluate the deposit. Stripping of the open pit area connnenced in the late fall of 1966 and the first test sample of ore was shipped to Chibougamau in December of that year.Regular ore shipments to the mill of Merrill Island Mining Corporation Limited for concentration commenced May 25, 1967. Production to December 31, 1970 amounts to 42,960,000 pounds of pay copper.The ore is chalcopyrite in white quartz dolomite, and it contains a very small amount of precious metals. The quartz dolomite assumes a flat to gently dipping attitude and is associated with a graphitic argillite contact zone on both hanging and footwall sides, in dolomitic limestone rocks. There is practically no other sulphide present in the ore.During the summer of 1969 a series of pre-concentration tests were completed and a Wemco heavy media sink float plant was installed in late 1969 and early 1970. This pre-concentrator eliminates at least one third of the ore mined in the form of barren quartz dolomite prior to ore shipment by truck to the concentrator in Chibougamau."

Jan 1, 1971

By Andrew Bamber

Outline ?Background to Mine-Mill Research at UBC ?Mine Mill Integration ?In situ mining methods ?Underground Pre-concentration ?System Design and Supporting Technologies ?Case Studies: ?INCO -McCreedyEast Mine ?Placer Dome ?Porcupine JV ISL Study ?Musselwhite, South Deep ?Falconbridge ?Fraser Copper ?Thayer Lindsley ?Wayside Gold, other scoping studies? ?System Designs ?Summary ?Future work ?Conclusion

May 1, 2006

By F. Charette

The paper reviews the requirements of the instrumentation required to monitor mining excavations in a high stress environment, and the development plan to instrument the D-Bolt in such a fashion as to be able to follow the behaviour of the bolts in relationship to the ground movements and support performance. Recent field observations of D-Bolts under static and dynamic conditions are also presented. Also discussed is the assumed mechanical behaviour of the D-Bolt. D-Bolts are used in two (2) Canadian underground mines operating in high stress environments and tested in three (3) other operations.

Jun 1, 2012

By John S. Stevenson

"Although we have no uranium- producing mines as yet in British Columbia, uranium, associated with gold and cobalt, has been found in two deposits in amounts such that the combined value of the metals not only warrants the further exploration of these deposits, but also encourages the search elsewhere in the Province for other similar deposits.Where uranium-bearing veins have been found in British Columbia, the uranium mineral is the crystalline variety of uranium oxide, uraninite, rather than the massive, non-crystalline variety, pitchblende, such as found in the Great Bear Lake deposit and in other similar deposits along the southwestern margin of the Precambrian shield.The principal occurrences of uranium known so far in British Columbia are associated with bodies of granodiorite and quartz diorite along the eastern side of the Coast Range belt of batholiths. In this part of the Province, interesting amounts of uranium occur on the Gem property in the Bridge River area and on the Victoria property south of Hazelton; and smaller amounts occur on the Red Rose, Rocher Debouze, Delta, and Ohio properties, also south of Hazelton. At the Gem and the Victoria, the uranium mineral, identified as uraninite, occurs in deposits that also contain abundant cobalt-nickel sulpharsenides, and molybdenite.At these properties, the uraninite occurs as clusters of small black crystals of sub-metallic lustre that may be seen upon careful -searching of a highly radioactive specimen with a hand lens. Under the microscope, the uraninite is seen to be in the form of cubes or modifications of cubes that may occur as individual grains widely scattered throughout the gangue or may be gathered into clusters of several grains. The grain size of the uraninite is in general small. Although a few clusters of grains are up to about 10 mesh in diameter, the individual grains, whether in clusters or widely disseminated, are rarely more than 400 mesh in diameter."

Jan 1, 1950

By V. Ogarlaci

Over 90% of the Romania's lignite reserve is located in the region of Oltenia, which is why this area is given special attention in the country's coal resources. Because the lignite deposit of Oltenia is comprised of 1-8 exploitable coal layers, their capitalizing calls for urgent arrangements to ensure rational exploitation under conditions of total safety, minimum losses and efficiency. The technology used the coal pits of North-Western Oltenia is the technology of excavation, transport and dumping in a continuous flow by using the complexes of excavation, transport and high-capacity dumping. The theme of this paper is of particular importance because the rhythmic operation in complete safety, is necessary both for sizing and keeping within the bounds of acceptable values, throughout the process of excavation of the geometric elements of the coal faces, marked by: the height of benches, slope angle and width of berms. Geometric dimensions of the benches of the open pits, the height of benches, slope angle and width of berms shall be calculated and shall be based on: the massif structure that forms the benches; physical-mechanical characteristics of rocks from the bench; working conditions, characterized mainly by mining and extraction methods applied; functional parameters of the mechanical equipment used to perform various operations on the coal face etc. For this study it was necessary a broad field for task tracking, measurement, research and design elements of the coal face, for land survey and a desk activity by: processing of topographic data, laboratory analyses on physical and mechanical properties of rocks and numerous specialized studies. In the final part, we bring some contributions to elucidating the issues of special importance for the lignite coal pits of Oltenia, coming up with data, graphics, formulas, solutions and concrete dimensioning of coal faces in terms of using technology in a continuous flow.

Aug 1, 2013

By Ken Major, Anita Marks, Craig Sams

In 2007 Copper Mountain Mining determined that there were sufficient resources to consider reopening the Similco Mine near Princeton, BC. The mill facility that had been built by Newmont Mining in 1972 was closed in 1996 and all of the process equipment removed. The mill had been built on the west side of the Similkameen River to facilitate mining of the Ingerbelle Deposit. In 1980 construction was completed on a primary crusher and cable belt to deliver ore across the Similkameen River from the Copper Mountain deposit to the Ingerbelle mill. With the decision to restart mining of the Copper Mountain deposit, the decision was made to design and build a 35,000 tpd grinding and flotation mill near the mining operations. This paper discusses the application of historical operating data for the selection of the mills for the new grinding circuit and provides an overview of the grinding circuit design.

Jan 1, 2012

By Tong Qin, Jinxia Zhang, Fusheng Niu, Limei Bai

"The interaction between a deformable bubble and a rigid particle in viscous liquids under microgravity conditions is studied by direct numerical simulation via an Arbitrary-Lagrangian-Eulerian (ALE) method. Due to the microgravity, the bubble will stay as a sphere in the fluid without external forces and its deformation is caused by the moving particle. In this study we assume the flow field is axisymmetric and the motion of the gas inside the bubble is neglected. The particle equations and the Navier-Stokes equations for the fluid are solved in a unified finite element framework. The particle obtains an impact velocity by an external force and the impact velocity is varied over a wide range. A ‘critical time scale’ T0 was identified for the interaction process. For successful contacts between particle and bubble, the time scale of their relative motion must be less than T0.INTRODUCTIONThe particle-bubble interaction is an important process in many applied industrial domains such as water treatment, froth flotation and liquid steel purification. It is a complex three phase process in that it embraces many research areas: fluid hydrodynamics, interfacial forces, particle and bubble behaviour and solution chemistry.Derjaguin and Dukhin(1961) clarified the particle-bubble interaction by introducing three-zone model for small and medium size particles. When the particle is far away from the bubble surface, the hydrodynamic forces are dominant. The particle is driven toward the bubble surface by the particle inertial and gravity. This region is regarded as Zone 1 and the interaction in this zone is a collision subprocess. As the particle gets close to the bubble, it exits a zone where the liquid flow around the bubble surface creates a tangential stream from the upper surface of the bubble toward the rear of the bubble. This is Zone 2 which is called the diffusiophoretic zone. In Zone 3, the particle is very closed to the bubble, surface forces like van der Waals, electrostatic and structural forces are considered. Contrast to Zone 1, Zone3 can be regarded as an attachment subprocess."

Jan 1, 2016