Search Documents

By Franco Chiesa, David Levasseur, Bernard Duchesne

A 500kg aluminium AlSi7Mg03 casting has been poured and the metallurgical quality at different locations inside the casting has been thoroughly investigated. It included measuring the local tensile properties (YS, UTS, El) in the T6 condition, the dendrite fineness (DAS) and the level of microporosity. A correlation was found between the microporosity level, the local solidification time and solidus front velocity; this correlation allows to predict the porosity level in large aluminium castings (solidification times between 20 and 200 minutes). Quite expectedly, properties varied widely within the casting and the actual mechanical properties were much less than the "textbook values" based on measurements carried out on separately cast standard specimens. A correlation between the secondary dendrite arm spacing (DAS) and the local solidification time was in keeping with previously published data. Finally the conditions to obtain an acceptable finish on machined surface were determined.

Jan 1, 2014

By Y. Miyabayashi, K. Nishikawa, H. Nagai

JX Nippon Mining & Metals Group recovers valuable metals from end-of-life electronic products in an economical and environmentally-benign way, based on technologies that have been acquired in mining, smelting, and refining operations over time. End-of-life electronic products contain halogens and hydrocarbons. When such materials are treated in the copper smelting process, corrosion of equipment and discoloration of sulfuric acid occur. As a countermeasure to these problems, we have developed pretreatment processes that include an incinerator, exhaust gas washing towers, and a defluorination facility. By implementing these improvements, we have been able to treat a large volume of end-of-life electronic products efficiently in the copper smelting process.

Jan 1, 2014

By G. Russo

During the construction of the S.Martin La Porte access adit, 9m in diameter, extreme squeezing conditions occurred while crossing Carboniferous schistose formations, with diametric convergence up to 2m. Back-analysis of monitoring results shows that an acceptable simulation of the observed excavation behaviour can be derived using a combined analytical and numerical approach, with simple elasto-plastic laws but a progressive reduction of residual parameters and a relevant increase of dilatancy.

May 1, 2009

By Q. Han

Irradiation of high energy ultrasonic vibration in metals and alloys generates oscillating strain and stress fields in solids, and introduces nonlinear effects such as cavitation, acoustic streaming, and radiation pressure in molten materials. These nonlinear effects can be utilized to assist conventional material processing processes. This article describes recent research at Oak Ridge National Labs (ORNL) and Purdue University on using high intensity ultrasonic vibrations for degassing molten aluminum, processing particulate reinforced metal matrix composites, refining metals and alloys during solidification process, welding, and producing bulk nanostructures in solid metals and alloys.

Jan 1, 2014

By Ron Ferris

The Westinghouse Temptifier TM, using heat pump principles, recovers lowgrade waste heat in the 600P to 1600P temperature range and amplifies it to usable levels of up to 2200P. Coefficients of performance (C.P.D.) normally encountered are from 3.0 to 6.0, with capacities from 200,000 to 10 million Btu/hr.

Jan 1, 1979

By G. J. Desroches, E. Ozberk, M. J. Collins, B. D. Krysa, I. M. Masters

The zinc refinery of Hudson Bay Mining and Smelting Co., Ltd. went through a major modernization in 1993, when the roaster and the calcine and fume leach circuits were replaced by a new Sherritt zinc pressure leach plant. The HBMS plant, in Flin Ron, Manitoba, represents the first commercial application of the Sherritt two-stage zinc pressure leach process, with /00% of the zinc concentrate feed processed in autoclaves. The process design of the new plant required definition of the deportments of elements such as antimony, arsenic, chlorine, cobalt, fluorine, germanium, magnesium, manganese, selenium, tellurium and thallium. This paper describes the deportment of these elements in the commercial zinc plant during the first nine months of pressure leach operation, and compares these results with operations prior to the introduction of pressure leaching, and with the results of tests carried out in the She"itt laboratory during the process development phase.

Jan 1, 1995

By Chuck Crowell

ISO Standards ?Provide Information to Address Commercial and Safety Needs for Standardization: ?Definitions and Terminology ?Test Methods ?Performance Criteria ?Conformity Assessment Process ?Developed by Global Experts ?Promote Global Harmonization

May 1, 2013

By Malcolm Scobie

"This paper reviews the evolution of Canadian surface and underground mining automation, principally relating to: advances in communications, initial development of machine teleoperation from line-of-sight remote control, and islands of automation. The eventual role of teleroboties and minewide robotic mining remains to be resolved. The progress and approaches adopted have tended to vary within each sector of the mining industry. Recent information technology advances have made possible the Digital Mine; in which information associated with all mining processes, however dispersed, would be integrated with support systems using new communications technology. The Digital Mine will provide the information infrastructure to serve as the foundation for minewide automation. This paper concludes by reviewing the issues likely to govern implementation success, relating to: mining process design, machine design, machine intelligence, and mine planning and control.IntroductionSignificant advances have recently been made in underground hardrock mine communications and teleoperation. Subsequent R&D efforts are mainly focussing on control systems for various types of machines. In underground potash mining, the realization of automated continuous mining systems appears to be imminent. Recent advances in surface mine dispatching, machine monitoring and global positioning systems (GPS) have tended to reactivate some of the initial R&D enthusiasm developed in the '70s for surface mine automation. Mines at large are approaching a major milestone: the implementation of comprehensive communications infrastructure which proves to be sufficiently reliable and economical to support the automation of routine mine production, either using teleoperated or autonomous machines. This then should motivate a deeper commitment to real time monitoring and management. The communications advances make possible the Digital Mine; in which information associated with all mining processes, however dispersed, would be integrated with support systems using information engineering. The Digital Mine will provide the information infrastructure to serve as the likely foundation for a wide range of automation scenarios. This paper surveys the status and directions of automation development in both surface and underground Canadian mines, pointing to what are seen to represent key technology development issues."

Jan 1, 1995

By Walter Curlook

"With Inco recording record profits over the past year, most people have forgotten the painful years of the last recession/depression when Inco was losing up to a million dollars a day for a short period . While high nickel prices have contributed to the exceptional recent profits, the real achievements stem from the tremendous advances in productivity and cost improvements that make Inco one of the lowest cost nickel producers.Some of the major advances in productivity have occurred in the mines. The establishment of Mining Research Departments in both Thompson and Copper Cliff in 1979/80 provided the stimulus and the opportunity to dedicate personnel to specific research projects, on a full-time basis; and more particularly to concentrate on the efficiency of the total mine system. The Copper Cliff North Mine was brought back into production as a research mine dedicated to the development and testing of new mining methods and equipment. A shop facility known as the ""Murray Shop"" was set up as the centre of innovation for the development and construction of prototype equipment required for new bulk mining methods. While other expenditures were being curtailed , investment in mining research was being increased. An early success was an ""in the hole"" drill that could be broken down into small components to access even the remotest sectors of a mine to convert labour intensive undercut-and-fill mining to "" vertical crater retreat "" , VCR, bulk mining. A new mine manufacturing company-Continuous Mining Systems-was incorporated with the objective of building innovative mining equipment, with strong focus on automated continuous sytems. Continuous Mining Systems has now grown to a $25 million per year business. With these synergistic thrusts, the VCR bulk mining method was implemented in all of the Ontario Division mines, raising the percentage of ore mined by bulk mining techniques from 320/0 in 1981 to over 90% today. Coupled with re-designed job responsibilities, sup- ported by appropriate training, mine productivity more than doubled. It was discovered that VCR mining could be adapted to the narrower Thompson mine ores with identical improvements in productivity. Development of the Thompson Open Pit North had an additional favourable impact on production cost s in Thompson. The timing of the open pit development could not have been better. It permitted Inco to rapidly increase production at high productivity and low cost, in years of record demand and prices."

Jan 1, 1990

By J. C. Thornley, H. L. J. Drummond

"Fifty years of wear on the original carbon steel shaft of this hydro turbine necessitated repair operations in 1980. Both austenitic and martensitic stainless steels have been used individually as journal materials in separate trials on an80-inch long and 22-inch diameter radial bearing but neither one nor the other has been successful.The wear and cracking problems of the stainless steels leading to the present abandonment of both classes of stainless steel are described. In particular the dependence of the toughness of type 410 stainless steel on its tempering temperature and the susceptibility of that steel to quench cracking are highlighted because problems have been caused by both of these metallurgical factors.IntroductionAs part of a desire to improve the efficiency of a fifty-year old hydro-electric generating station on the Saint John River, the decision was made to change the journal and bearing material for the shaft bearings, which are stave-type bearings. For the initial fifty years of operation the bearings had been wooden (lignum vitae) and had run on the carbon steel shaft directly. For one of the four unit s at this station the performance of this combination has been truly excellent, and the remaining three sets of bearings had performed well. However there had been shaft wear on the units and the wear had made the shafts somewhat elliptical when a decision was made to install some sort of new journal on to three of the old shafts. [In addition to the wear on the carbon steel journals it was found that one shaft was significantly softer in the bearing area than it was immediately above the bearings (180 Vickers in comparison with 230 to 250 Vickers)] ."

Jan 1, 1985

Why innovate? ? How are we doing in Canada? ? How can we do better? ? Why now? ? What?s next? ? Lowering production costs ? Improving productivity ? Increasing value-added ? Discovering new mines, extending life of existing ore bodies ? Reducing environmental footprint ? Improving health and safety

May 1, 2008

By Harvey McLeod

M3 -Technology HOWEVER:In practice we have limitations ?Clients: aggressive or cost based; inexperienced ?Consultants: ?expanding market w/training limitations ?Prescriptive designs ?Lack of senior oversight ?Regulators: difficult to retain technical capacity ?Stakeholders: perceptions and expectations ?Physical settings: challenging terrain, climate, soils/rock Do M3?s Perform? YES?Generally M3?s since mid-1960 do perform ?BC Closed Mines: Afton, Highmont, Trojan, Bethlehem, Cheni, SNIP, NO?ARD/ML issues?e.g. Equity Silver, Samatosum; selenium, cadmium, sulphate

May 1, 2010

By J. H. Curran

Agenda ? Challenges of developed world mining ? Software aids for creative and practical engineering ? Rocscience software philosophy ? Rocscience suite of geomechanics programs ? Case study ? design of de-stress slot Mining Challenges of the Developed World ? Dwindling reserves ? Great depths ? Strict operating and environmental regulations ? Competition from lower cost operations in developing countries

Apr 1, 2005

By M. Muinonen, A. R. Barnes, R. Pandher, M. J. Lavigne

Over the past three years, Ring of Fire chromite ores have been tested extensively at both the bench scale and pilot scale at XPS Consulting and Testwork Services. Following bench scale testwork, two smelting campaigns were completed using a 300 kW DC arc furnace on different chromite deposits from the Ring of Fire. A ChemSheet model was developed to aid in the design and optimization of the recipes, and its predictions were confirmed with both the bench scale and pilot scale tests. A total of 7.5 tonnes of chromite ore was smelted at XPS. The results of the testwork demonstrate excellent reducibility for the ores tested with good reduction kinetics when compared with South African chromites.

Jan 1, 2014

By R. Esteban, D. Runnels, S. Girgin, J. Torrealba-Vargas

"Each mineral processing project requires early testwork to evaluate the economic potential of a deposit. The testwork needs to be efficient and it should provide enough information to obtain key parameters, first for a high level flowsheet selection at the conceptual and PEA stages and then, for later stages, to confirm the flowsheet selection and optimize the metallurgical efficiency of the plant. The testwork should consider all rock types or lithologies present, and carry out testwork for the purpose of sizing the major processing equipment.A successful project requires that the project stakeholders develop an efficient sample collection program to produce enough material for a scoping and pre-feasibility level program. This involves the participation of a team of geologists, mining and metallurgical engineers in the project, as early as possible, to define the deposit characteristics that need to be validated.The project schedule requires a close control of the testwork scope, procedures, and timing, but also the efficient analysis of results to provide indications of red flags that could impact circuit design as early as possible.In some cases, projects are put on hold due to fluctuations of the world economy until the return of more favorable conditions. In that scenario, prior data analysis of former testwork results could reduce significantly the amount of testwork required to restart a project. The paper will also present examples where the analysis of former testwork data was used to reduce the amount of new testwork in addition to presenting examples of latest projects where the above-mentioned test program approach was followed."

Jan 1, 2016

By J. A. Drozdiak, A. Bamber

In this paper we examine, through pilot-scale testing, the possibility of operating a circuit comprised of two stages of HPGR comminution, followed by grinding through a horizontal stirred mill. In order to assess whether the novel circuit design could achieve the reduced energy requirements indicated in the literature, two more-established circuits, a cone crusher / ball mill and an HPGR / ball mill, were examined using a combination of testing and flowsheet simulation. The results showed that, based solely on the specific energy requirements for comminution, the HPGR / stirred mill circuit achieved a reduction of 9.2% and 16.7% over the HPGR / ball mill and cone crusher / ball mill circuits, respectively.

Jan 1, 2012

By M. Leijd, K. S. Forrester, M. Saxon, M. Oczlon

This paper provides an introduction to wet high intensity magnetic separation (WHIMS) and its successful application to the beneficiation of rare earth element (REE) enriched eudialyte. The analysis includes an in-depth reporting of the deportment of key elements as well as a statistical interpretation of the relative importance of operational parameters including magnetic field intensity, flow velocity, and matrix loading density. Conclusions are drawn on the relative success of the technology, potential areas for process improvement, and the research direction that continues to be investigated. Three original equipment manufacturer (OEM) technologies were subjected to a series of screening and characterization tests to identify the optimal operating parameter set to magnetically beneficiate eudialyte from Norra Kärr, Sweden. Upon the completion of the characterization test it was apparent that the Metso HGMS technology was superior with respect to REE recovery and gangue rejection for the Norra Kärr composite. The Metso HGMS was then subjected to a series of verification tests to confirm the repeatability and reproducibility of the system.

Jan 1, 2014

By J. Kuipers, R. W. Lawrence, P. B. Marchant, W. Brooks, J. T. Chapman

"Bioleach testing and piloting was conducted on refractory gold sulphide concentrate from Austin Gold Venture in Nevada during 1988. The objective of the test programme was to determine the technical and commercial viability of bioleaching as a concentrate pretreatment step prior to gold extraction by cyanidation. Baseline CIL cyanidation typically resulted in < 20% gold extraction from the Austin concentrate. Bioleaching enhanced gold extraction up to 95% using conventional CIL techniques. This paper summarizes the bioleach test programme and results, including pilot plant studies onsite, and describes the commercial design details for a possible retrofit of the Austin flotation tailings leach circuit to accommodate 20 tpd and 40 tpd capacity concentrate bioleach facilities.INTRODUCTIONBioleach testing on a refractory carbonaceous sulphide concentrate from Austin Gold Venture (AGV), was initiated in late 1987 as part of an ongoing programme at Austin to investigate alternatives to concentrate smelting. Preliminary batch biooxidation tests at Coastech indicated that over 90% gold extraction by carbon-in-leach (CIL) cyanidation of the bioleach residue could be achieved, compared with less than 20% gold extraction on untreated concentrate by similar CIL processing.Subsequently, a more rigorous laboratory study was undertaken at Coastech to establish continuous biooxidation operating criteria on a bench scale. The objective of continuous testing in the laboratory was to provide confirmation of enhanced CIL response based on continuous bioleach products and to determine key process operating and design parameters for pilot testing. The success of the laboratory test program led to the installation of a mobile pilot plant at Austin Gold Venture. The plant was operated by Coastech and AGV during 1988 to provide scaleup data and design criteria for commercial design and feasibility analysis. Based on pilot plant operating data, a detailed commercial bioleach plant was designed as a possible retrofit to the existing 1000 tpd CIL plant. Capital and operating costs were estimated to provide a commercial feasibility study of bioleaching as an oxidative pretreatment for Austin refractory concentrate."

Jan 1, 1989

By Robert B. Parsons

"The February 18, 1987, Federal Budget contains a proposed amendment which would simplify somewhat the ""successor corporation"" rules in the Income Tax Act. Despite this amendment, though, the important successor rules will continue to be relatively complex.IntroductionThe February 18, 1987, Federal Budget papers propose an income tax amendment whereby the so-called ""successor corporation"" rules would be revised by removing the present provision which limits the application of these rules to a maximum of two ""successions"". The successor corporation rules represent one of the most complicated sets of rules in the Income Tax Act. This month, Tax Notes seeks to explain these rules and the proposed amendment in simplified terms.Basically, the successor rules provide a mechanism for transferring unused exploration and development expenses from one taxpayer to another , in specified circumstances. The aforementioned limitation of two successions refers to the rule which allows a maximum of two such transfers with respect to any particular pool of deductions."

Jan 1, 1987

By P. Condori, G. Rech, J. Winnett

"Palabora Mining Copper has a unique ore body composition which unlike other copper ore bodies has three main components in significant proportions; these are copper bearing ore, magnetite and dolerite. The high content of dolerite, a hard barren material, creates a high proportion of pebbles which normally are recycled back to the mill. This action increases the mill bearing pressure and power progressively until corrective actions are taken.A logical action to solve the pebbles generation would be to incorporate a pebble crusher. This in fact was done however two fundamental issues were encountered; the high content of magnetite and existence of a cyclone classification section. Due to the high content of magnetite, metal detectors have not been able to work efficiently to separate tramp metal which causes damage to the pebble crushers. The existence of cyclones in the circuit had a detrimental effect on the final product when the pebbles crusher was online producing coarse sandy material.Due to the difficulties in treating pebbles via conventional procedures and the unique Palabora ore composition and characteristics, sorting technology was investigated at laboratory and pilot scale. It was found that a combination of optical and electromagnetic sorting could efficiently separate dolerite from the copper bearing and magnetite ores.This paper reports the findings of the laboratory and pilot scale work performed and discusses the additional benefits to the circuit."

Jan 1, 2012