Search Documents

By A. S. H. Kabir, I-H. Jung, J. Su, S. Yue, M. Sanjari

The final mechanical properties of wrought magnesium alloys are mostly controlled by microstructure and crystallographic orientation or texture. In common magnesium alloys, grain coarsening occurs during annealing process and formation of undesirable basal texture cannot be changed markedly. The aim of this work is to investigate the effect of static precipitation on microstructure and texture evolution during annealing at 250 °C after warm rolling of Mg-Al-Sn alloy. Mg-3Al-3Sn (wt. %) alloy has been designed using thermodynamic modeling software, FactSageTM, based on forming target stable and incoherent Mg2Sn precipitate within the industrial deformation temperature range. Microstructures and precipitation were investigated by optical and scanning electron microscopes and macro-texture was measured by X-ray diffraction (XRD) techniques. It was found that static precipitates form in a large scale at the recrystallized grain boundaries and retards the grain growth during annealing. Slight weakening in basal texture was also observed during annealing.

Jan 1, 2014

By E. G. Joe

"The continuing increase in costs for power and fuel are affecting significantly the cost for milling of Canadian ores. In order to ascertain the scope and source of energy consumption in Canadian mills for further energy conservation opportunities, CANMET, in cooperation with the Canadian Mineral Processors carried out a detailed survey on the metallic mineral processing plants. Sixty-seven mills representing almost 300 million tons of annual capacity participated in the survey. The results indicated that in general, copper and iron ore mills, representing the bulk of the tonnage, consumed relatively low levels of energy per ton. Nickel-copper, zinc-copper and lead-zinc ore mills were moderate in energy consumption, while uranium and some copper-lead-zinc mills reported much higher energy consumptions due primarily to the increased heat requirements of the ore pulp. While the plant heating costs varied somewhat with the location in Canada, it was apparent that the lowest heating costs were achieved by those built with proper insulation and energy conservation design. If the cost per million British Thermal Units is taken as $2.00, the mill energy costs generally ranged from 40¢/ton up to $1.20/ton.IntroductionEnergy consumption in milling has always been of significant interest to Canadian mineral processors who traditionally calculate their milling costs down to pennies per ton. Even the measure of an ore's grindability is expressed empirically by Bond in kilowatts hours per ton milled. Some of the mills located in isolated areas were obliged to generate their own electrical energy from fossil or petroleum-based fuel at a cost substantially higher than that obtainable from captive or public hydro-electric installations. These mills practiced energy conservation long before the advent of O.P.E.C. energy cost inflation. One example of this was the use of electric boilers to produce process and heating steam during off-peak electrical load periods."

Jan 1, 1978

By Akira Miura, Katsuyuki Sato, Yuken Fukano

JX Nippon Mining and Metals Corporation has developed the JX Iodine Process, which is an innovative and patented copper-leaching process for low-grade primary sulfide ores. This process consists of the irrigation of ferric iron and a low concentration of iodide solutions. One-meter column leaching tests were conducted on ore samples from two different mines. At the end of experiments, the total copper recovery exceeded 70% for Sample A and 50% for Sample B with the iodine method, which was significantly higher than that with conventional ferric leaching of 14% for Sample A and 20% for Sample B. To elucidate the reason for the JX Iodine Process effectiveness, cross sections of leached residues were studied. Reaction products were confirmed around chalcopyrite even in the central area of particles in Sample A, however, reaction products were recognized at a depth of only 1 mm from the ore rim in Sample The resistance of Sample A to the leachate appeared to be lower than that of Sample B because Sample A had a high permeability and porosity, whereas Sample B had been affected strongly by a potassium alteration. No reaction products were visible on conventional leaching samples, even at the ore surfaces. INTRODUCTION Hydrometallurgical copper leaching (heap leaching or dump leaching) has been used extensively for copper recovery from oxide and secondary-sulfide ores, but not for primary copper sulfides, which contain mainly chalcopyrite as copper minerals. Although they are major resources of copper, primary copper sulfides are difficult to process because of their refractory nature. Extensive leaching studies have been carried out to leach primary copper sulfides (chalcopyrite), including biological and chemical, using a variety of oxidants and additives to enhance copper recovery. Watling (2013) reviewed acid-chloride-oxidizing agents with chalcopyrite. Abdollahi et al. (2015) tested silver as a catalyst for bioleaching with a chalcopyrite-bearing molybdenite concentrate. Hiroyoshi, Miki, Hirajima and Tsunekawa (2000) found a specific redox-potential zone for high-speed chalcopyrite leaching by controlling the ratio of ferric and ferrous iron. However, no ambient-temperature economic process has been developed for leaching primary copper sulfide, which usually has a low copper grade.

Jan 1, 2019

By Peter Lighthall

What is an engineering firm?s role? ? The ideal situation is a life of mine service alliance with the owner ? Engineering firms are long term custodians of information ? Maintain consistency with established closure objectives, adjust closure plans to meet changing situations and technologies ? Develop range of solutions and present owners with risk profile The mine closure planning process ?new mines ? For metal mining, geochemistry is the issue ? The planning process: ?Sampling ?Waste characterization ?ARD prediction ?ARD control strategies ?Life of mine waste management planning ?Assessment of residual impacts ?Development of strategies for dealing with residual impacts ?Estimate closure costs ?One time decommissioning and reclamation costs ?Ongoing treatment/maintenance costs

May 1, 2006

By R. Thierbach, W. Kahnt, Oberthür. T., D. Eisenburger, V. Gundelach

ABSTRACT: The ground penetrating radar (GPR) method was used in a platinum mine in Zimbabwe by members of the Federal Institute for Geosciences and Mineral Resources (BGR). The measurements were carried out in boreholes and drifts. Electromagnetic re?ections from a fault that consistently trends parallel to the mineralization zone permitted the mapping of the economically minable parts of the deposit. An introduction is given to the geology of the studied area and the application of the GPR method. The electrical parametres of the rocks are measured in situ, the GPR measurements are displayed with radargrams, and the visible structures are explained in illustrations.

Jan 1, 2010

By Wojciech Naworyta

The development of the Gubin lignite deposit, located in western Poland is the first mining investment of this magnitude in 30 years. Gubin is the second largest prospective lignite deposit in Poland, with over one billion tonnes of indicated reserves, which would be sufficient for a 2700 MW power plant for almost 50 years. The paper presents select problems related to the mining development of Gubin deposit. Attention has been paid to changes in legal and formal requirements for mining investments that were introduced after the change of Polish social and economic system. The significance of spatial, environmental and social conditionings has been emphasized. Typical attributes of the mine planning process have also been presented. Those include the long time horizon of the investment, uncertainty of external conditions and resulting difficulties in the project?s economic evaluation. Focus has been placed on mutual connections between particular elements of the project and time dependence during the process of their development. Iterative characteristics of the design process have been proven, together with resulting necessity of frequent verification of previous assumptions. As a background for presenting selected problems related to future development of Gubin lignite deposit, the methods of design have been discussed ? the variants method, the empirical method and the method of consecutive approximations. The tools and the possibilities of their use for solving specific problems related to mine design of an open pit have been broadly discussed. The chapter in which the authors relate to the specific problems of Gubin deposit development constitutes the main part of the paper. It depicts the assumptions on which the annual production and the total extraction of lignite during life-of-mine period have been based. The process of mine designing has been discussed, taking into consideration environmental, geotechnical, spatial, social and mining conditions. The criteria for choosing the location of the opening cut and the external dump have been mentioned. In the summary, the present state of mine design progress has been presented, together with some problems that will need to be solved during the next stages of the deposit?s development.

Aug 1, 2013

By Marty Hudyma

Mining-induced seismicity and rockbursting is one of the primary risks in deep mines. Seismic data management software has been created to facilitate analysis of mining-induced seismicity. The Mine Seismicity Risk Analysis Program (MS-RAP) is a purpose built database with mine seismicity analysis tools. One of the primary features of MS-RAP is the creation of seismic hazard maps in quasi-real time. The seismic hazard maps identify areas that are more prone to large seismic events and rockbursts, allowing risk management measures to be focused on the areas of greatest risk. These maps allow mining engineers to be more proactive about identifying and managing seismic related geomechanics risks in mines.

Oct 1, 2009

By Marty Hudyma

Mining-induced seismicity and rockbursting is one of the primary risks in deep mines. Seismic data management software has been created to facilitate analysis of mining-induced seismicity. The Mine Seismicity Risk Analysis Program (MS-RAP) is a purpose built database with mine seismicity analysis tools. One of the primary features of MS-RAP is the creation of seismic hazard maps in quasi-real time. The seismic hazard maps identify areas that are more prone to large seismic events and rockbursts, allowing risk management measures to be focused on the areas of greatest risk. These maps allow mining engineers to be more proactive about identifying and managing seismic related geomechanics risks in mines.

Oct 1, 2009

By Changyoon Kim

Technological advances in mobile systems, such as smartphones and tablet computers, provide engineers with new opportunities to enhance the current facility management processes. Equipped with powerful system processors, touch screens, and wireless communication capabilities, mobile systems enable the experience of omnipresence of facility information. Building information modeling (BIM) also enables improvements in facility management. With an advanced data structure and visualization capacity, BIM can be used in numerous applications for facility management. This study aims to incorporate the strength of mobile systems and BIM in facility management. The proposed system, which utilizes smartphone technology, allows engineers to conduct facility management functions, such as maintenance planning, inspection, and assessment, irrespective of a user?s location. The integration of building information modeling in a system provides detailed visual information of the building components. A case study was conducted to verify the applicability of the mobile system in terms of the hardware functions, system design, and user interface. This proposed system, with its study results, provides a guideline as to how mobile systems can be effectively integrated with BIM for improved management of facility information.

Aug 1, 2013

By Sadan Kelebek, S. O. Fekete, Gerhard W. Heinrich, Peter F. Wells

"For many years, rejection of pyrrhotite at the milling stage has been a viable method for sulphur dioxide abatement. Pyrrhotite rejection options have included the use of selective pyrrhotite depressants in flotation; a depressant which has recently come into use is diethylenetriamine (DETA). This reagent has been the subject of recent research and development efforts in the processing of nickel-copper sulphide ores.In the present study, adsorption trends for DETA have been monitored under the dynamic conditions of flotation using a spectrophotometric method which has been adopted for this purpose at Falconbridge Limited. The results indicate that the adsorption of DETA is quite fast and in the majority of cases, accounts for the disappearance of 75-95 % of this reagent from pulp's liquid phase. The adsorption decreases linearly with an increase in the DET A dosage from 100 git to 600 git. The tailings produced in flotation tests were subjected to washing with deionized water at 60 °C to examine the desorption of DET A. These results indicate that the amount desorbed increases with increasing DETA dosage used during flotation but is less than 7 per cent of that adsorbed. It was found that adsorption of DETA alone, even at relatively high levels, does not always cause depression of pyrrhotite. A new combination of reagents identified in the metallurgical laboratories of Falconbridge Limited utilizes sulphur dioxide with DETA. These reagents together are capable of efficient depression of pyrrhotite on a consistent basis."

Jan 1, 1995

By S. McCarthy, K. E. Waters, A. Jordens

The beneficiation of rare earth (RE) element bearing minerals has become an active area of research as applications for these elements grow while the supply to non-Chinese consumers is restricted by export quotas. One of the most interesting beneficiation techniques for RE minerals is froth flotation as their unique chemistry suggests that collectors with a specific affinity for RE cations should be able to selectively recover these minerals. Existing literature, focusing mainly on bastnäsite flotation, identifies hydroxamic acids as excellent collectors for RE minerals. The high stability of hydroxamate-RE cation complexes is the explanation most often offered for the observed selectivity of these reagents in bastnäsite flotation however some research has also suggested that mineral solubility plays a crucial role in the success of hydroxamic acid flotation of RE minerals. This work investigates the interaction of allanite, a relatively insoluble RE-silicate mineral, with benzohydroxamic acid using zeta potential measurements and microflotation. The effects of Fe(III) and Fe(II) ions as potential activating ions (cations that form stable hydroxamate complexes) on benzohydroxamic adsorption to the allanite surface are investigated as a potential solution to promote hydroxamic acid adsorption. The results indicate that the optimum conditions for separation of allanite from quartz occur at pH 4 using FeCl2 as an activator for benzohydroxamic acid adsorption.

Jan 1, 2014

By J. Drozdiak

In this paper we present the results of preliminary investigations into the applicability of new laboratory scale tests for the prediction of operating gap and specific throughput in high pressure grinding rolls (HPGR). The work is a part of the CAMIRO HPGR research program being conducted at the University of British Columbia, which aims to develop a suite of small-scale tests and procedures for the selection and sizing of HPGRs. A focus of the presented study is to test sample types in terms of their terra-mechanics based characteristics and relate them to specific throughput and gap results from pilot HPGR testing on the same samples.

Jan 1, 2012

An optimization process is described that can be systematically applied by mine planners to produce life-of-mine schedules aligned with their strategic targets, while maximizing the net present value of the mining operation. The software tool employed uses heuristics and an evolutionary algorithm to generate life-of-mine schedules of production and development activities. Generating such schedules is typically a very difficult task due to the large number of operational constraints that must be respected, and the vast number of alternative schedules; as a result the value of the mining operation can be compromised. With an expansion at Newmont?s Leeville mine in Nevada, the mine planners were given the task of producing feasible life-of-mine schedules with significantly increased production rates. Their initial efforts indicated that it would be a considerable challenge to generate such schedules in a timely manner. By systematically applying the proposed optimization process, the mine planners were able to generate optimized life-of-mine schedules with the desired production rate.

Aug 1, 2013

By A. Suzue, T. H. Okabe, Y. Taninouchi

Methods for the physical separation and enrichment of platinum group metals (PGMs) from autocatalyst scrap were studied in order to develop an environmentally friendly and efficient recycling process. In general, an autocatalyst has a honeycomb-structured ceramic substrate that is coated with a catalyst layer containing platinum (Pt), palladium (Pd), and rhodium (Rh). Therefore, physical separation of the PGM-containing catalyst layer directly from the ceramic substrate is favorable for upgrading the autocatalyst scrap. In this paper, the authors present a scrap-upgrade process consisting of electroless iron plating and magnetic separation techniques. Iron was plated on the surface of a catalyst sample used to represent an autocatalyst, which was then crushed and magnetically separated. The Pd in the catalyst sample was successfully extracted and concentrated in the magnetic powder. Under certain conditions, the process increased the Pd concentration by a factor of 4 and recovered 89% of the Pd in the autocatalyst sample.

Jan 1, 2014

By A. R. Guest, R. Clayton, J. Jakubec

"The potential for mudrushes is a potential hazard that should be evaluated during cave mining studies. Mudrushes are a phenomenon that can have very different origins, but produce the same results: injury, loss of life, damage to property, excess dilution, production delays, or mine closure. Although mudrushes are more common in cave mines than other mines, any mining activity that enables the accumulation of fine particles and water is susceptible to mudflow. This paper describes the process developed by the authors during the past decade to evaluate the risk of mudrushes, specifically in caving and sublevel caving mines.RÉSUMÉ Un danger potentiel qui devrait être évalué durant les études d’exploitation par blocs foudroyés est la possibilité d’afflux de boue. Le phénomène des afflux de boue peut avoir des origines très diverses; les résultats sont cependant les mêmes : des blessures, des pertes de vie, des dommages à la propriété, une dilution excessive, des délais de production ou des fermetures de mines. Bien que les afflux de boue soient plus fréquents dans les mines exploitées par blocs foudroyés, toute activité minière qui permet l’accumulation de particules fines et d’eau est sujette à des coulées de boue. Le présent article décrit le processus développé par les auteurs au cours de la dernière décennie pour évaluer le risque d’afflux de boue, surtout dans les mines exploitées par blocs foudroyés et par sousniveaux foudroyés."

Jan 1, 2016

By M. P. Amsden

"Ecstall Mining Limited, a subsidiary of Texasgulf, Inc., Operates the Kidd Creek Mine, Concentrator and Zinc Plant at Timmins, Ontario. Two different ore types are mined and milled to produce concentrates of copper, zinc, lead and tin. The ores are processed at the Concentrator in three separate individual milling circuits, each with the capacity to treat up to 3500 tons per day. Two circuits treat copper-zinc ore 1t an average combined rate of 6500 tons per day and the third circuit treats 3500 tons per day of silver-lead zinc ore. Conventional crushing, grinding and flotation procedures are followed. The purpose of this paper is to describe Ecstall's experience with rubber mill linings in the grinding circuits.CrushingBoth ores are crushed to minus 6 inches at the Mine and delivered by rail to the Concentrator where they are reduced by secondary and tertiary crushing to minus 5/8 inch.GrindingThe crushed ores are prepared for selective flotation by grinding with rod mills and two stages of ball milling. flotation circuit middling products are reground in regrind mills prior to further treatment. A typical flowsheet of one of the grinding circuits is shown in Figure 1.All the grinding units are Allis-Chalmers Mills. The rod mills are 10 1/2 feet diameter by 16 feet long. Both the primary and secondary ball mills are 12 feet diameter by 18 feet long and all regrind mills are 6 feet diameter by 12 feet long. The primary mills are charged with 1 13/16 inch forged balls. Secondary mills are charged with 1 1/2 inch forged balls and the regrind mills are charged with 1 inch forged balls. All cyclones are Kreb units. The primary cyclones are Dl5B hydrocyclones, the secondary cyclones are D6B hydrocyclones and all regrind cyclones are D6B hydrocyclones."

Jan 1, 1974

By A. E. M. Warner, A. Vahed, P. J. Mackey

In the decade 2002 to 2012 some 6.7 million tonnes of new copper concentrate production capacity was brought on line, corresponding to 2 million tonnes of contained copper. This increase in concentrate supply necessitated the commissioning of a number of new copper smelters as well as the modernization and/or expansion of existing plants to meet the demand. This paper gives an overview of the copper extractive industry, reviews recent copper production trends and changes in the copper industry, including an examination of pyrometallurgical and hydrometallurgical technology developments. WorleyParsons has supported a number of the projects involved in these developments and this role is briefly discussed. The paper introduces a number of ideas related to possible future directions of the copper industry.

Jan 1, 2014

By Jianglan Duan, Steve L. Cockcroft, Andre B. Phillion, Carl Reilly, Daan M. Maijer

"In the aluminum alloy wheel casting process, careful design of the cooling system in the die and its operation (cooling channel timing) are critical to achieve quality and productivity goals. The problem is challenging owing to the cyclic nature of the process and the relatively large thermal mass of the die in comparison to the wheel. For a given die geometry, a set of constraints have been defined to ensure directional solidification and an objective function, based on cooling rate during solidification, has been defined to reach a target secondary dendrite arm spacing. The methodology presented in this study employs the commercial finite element package, ABAQUSTM, and an optimization module based on the open source library, Scipy. The developed methodology has been applied to a series of geometries and cooling system configurations, including a 2-D axisymmetric wheel and die assembly generated from a prototype die. Preliminary testing has shown that careful selection of the objective and constraint functions have made it possible to reach desired solidification pattern.TM- Dassault Systèmes Corp."

Jan 1, 2014

By Alok Porwal, E. J. M. Carranza, M. Hale

Abstract- Approaches to mineral potential mapping based on weights of evidence generally use binary maps, whereas, real-world geospatial data are mostly multi-class in nature. The consequent reclassification of multi-class maps into binary maps is a simplification that might result in a loss of information. This paper describes results of using multi-class evidential maps in an extended weights-of-evidence model vis-à-vis results of using binary evidential maps in a simple-weights-ofevidence model. The study area in the south-central part of Aravalli province (western India) hosts a number of SEDEX-type base metal deposits in Proterozoic supracrustal rocks. Recognition criteria for base metal deposits were represented as both multi-class and binary evidential maps. The known mineral deposits were divided into two subsets, viz., the training and the validation subsets. The training subset was used to calculate, for the evidential maps, the weights, contrasts, and posterior probabilities and their variances. The distributions of expected frequencies of base metal deposits estimated from the posterior probabilities and the observed frequencies were compared using standard goodness-of-fit tests to verify conditional independence of the input evidential maps. The posterior probabilities from both the models were mapped and interpreted to classify the study area into zones favorable, permissive, and non-permissive for base metal deposit occurrence. As compared to the simple weights-of-evidence model, the extended weights-of-evidence model results in more robust and finely differentiated posterior probabilities in favorable and permissive zones and has a better prediction rate. The results also reveal that the statistical properties of the weights of evidence, the contrasts, and the posterior probabilities are not significantly degenerated by using multi-class evidential maps in weights-of-evidence modelling.

Jan 1, 2001

By G. Tairova, J. Ioffe

Arsenic, selenium and mercury species are common contaminants in mining aqueous streams and present significant environmental and health problems. The objective of this project is to investigate methods to lower the concentrations of these elements in mining aqueous streams. A new composite media for removal of these elements of concern from mining effluents was developed. The results of bench scale and pilot plant experiments, using the media, indicated removal of arsenic, selenium, mercury and other elements of concern below detection limits.

Jan 1, 2014