Search Documents

By M. S. Moats

"The effects of commercial copper electrorefining additives (glue and thiourea) on the electrochemical removal of bismuth are of importance in copper production. It was found that Bi(III) electrodeposition occurs readily from acidic sulfate solution via a diffusion-controlled quasi-reversible reduction. The diffusion coefficient of Bi(III) was measured and found to be less than reported values of copper in similar solutions. The presence of thiourea and/or glue was found to accelerate or de-polarize Bi(III) reduction on stainless steel as compared to the inhibition or polarization of Cu(II) reduction. The additives also inhibited the dissolution of the Bi-Cu co-deposit during cyclic voltammetry. During short term deposition studies, the additives increased the concentration of Bi in co-deposited Cu-Bi products from solutions with low concentrations of Cu (<2 g/L). Bi deposition was significantly suppressed by increasing the Cu(II) concentration in the solution. The formation of a copper layer on the stainless steel electrode appeared to significantly suppress the reduction of Bi(III). This study demonstrates that glue and thiourea depolarize the deposition of bismuth on stainless steel. Therefore, the additives could be used to improve Bi impurity removal during third stage liberation.INTRODUCTIONThe production of high purity copper has been steadily increasing due to the wide application of the metal and its alloys in electrical and electronic products, infrastructure construction, industrial machinery and equipment, general products and transportation (Moskalyk et al., 2003). Most high purity copper is manufactured from copper sulfide mineral concentrates and/or scrap via a pyrometallurgical process followed by electrorefining (Navarro et al., 1999). During the electrorefining process, cast anodes of 99-99.5% purity are electrochemically dissolved into an acidified copper sulfate solution while high purity copper (>99.99%) is plated on stainless steel blanks or copper starter sheets (Davenport et al., 2002). The control of cathode deposit growth (purity and morphology) while maintaining a high current efficiency is of significant importance for copper refining (Ilkhchi et al., 2007). At typically applied current densities for industrial copper electrorefining, mass and charge transfer play important roles in the quality of cathodic products (Hiskey et al., 1998). If the real current density at some surface points is substantially higher owing to uneven current distribution, then rough spots can and will grow faster leading to nodules (Suarez et al., 1992). Nodulated deposits tend to capture solution and anode impurities (slimes) resulting in unacceptable cathode quality (Afifi et al., 1987). Furthermore, these nodules can grow until they eventually contact the anode leading to short circuits and current efficiency reduction (Ilkhchi et al. 2007)."

Jan 1, 2016

By Poul Hansen

"In mid-1986, a world-class mining enterprise was created in Highland Valley, British Columbia, bringing together the copper mining operations of Lomex and Cominco . In 1988, Highmont joined the new partnership.Highland Valley Copper is the largest copper mine in North America in terms of both tonnage mined and tonnage milled, and it is one of the largest in the world. Due to its relatively low ore grade its production of copper in concentrate ranks about ninth in the Western World.The current eighteen year mine plan is based on ore reserves of 761 million tonnes. The daily milling rate is 133 000 tonnes. At the end of mine life, a total area of approximately 6500 hectares will have been disturbed. At this time, vegetation has been established on about 600 hectares and while work will be done during the operating years, it will not be until the end of mine life, about 2008, that the last half of the land can be reclaimed and revegetated.Once final reclamation has been accomplished, Highland Valley Copper will have completed its "" temporary use of the land"". In the meantime, about 1250people have had employment for about 50 000 man years, at wages ranking among the best in Canada.IntroductionTo provide and sustain our way of life, we need steel, copper, aluminum, zinc and many other minerals.To sustain mining, we must have adequate ore reserves and replacement of reserves as they are mined. Each year the search becomes more difficult as more of the Earth&apos;s surface is investigated and depo sits are mined. This calls for aggressive and sustained efforts.In British Columbia, past and present mining activities have disturbed less than one-tenth of one per cent of the land.With today’s technology, mining operations can be substantially reclaimed and thus complete the cycle of ""A Temporary Use of the Land""."

Jan 1, 1992

By K. Sinding, R. Poulin

"Recent land-use decisions in British Colwnbia, and the publication of a report on compensation for expropriations of resource interests, have highlighted the nature of land use policies. Landuse decisions, such as the creation of large new parks, raise three principal issues which have implications for how land-use policy is conducted and how it impacts on the mining industry. The first is the identity of the parties advocating different land-use policies and their motives for doing so, the second is the changing nature of benefits derived from land, and the third is the change of property-rights regime which is devised to accommodate the (changing) benefits from using land and natural resources, as well as the interests of the different parties involved.Involved Parties and BenefitsThe process of establishing or modifying property rights depends on the interest groups involved. Three distinct categories, each with distinct incentives which can influence the process, must be distinguished: private claimants, politicians and bureaucrats (Libecap, 1989).The first groups claim rents and management powers through asset ownership. They may be incumbent owners seeking enforcement of the status quo, new claimants seeking redistribution of assets, or third parties who depend on the distribution of assets (e.g. lenders, labour suppliers and contractors). Some infonnal property arrangements can be negotiated within the group whereas others requires action in the political arena through lobbying politicians for (re)allocation of property rights and influencing bureaucrats for favourable administrative decisions. The second category is politicians, who direct the powers of the state to change or enforce property rights. Both incwnbents and office-seekers fall in this category and their actions and opinions are shaped by their constituencies and financial backers. However, not all causes can be championed and trade-offs have to be made, resulting in decisions that maximize political benefits. The third category of parties in the process is the bureaucrats. The power to manage has been delegated by politicians but bureaucrats also have opportunities and incentives to further their own interests. These can include maintaining or expanding jurisdictional turf or increasing operating budgets (Libecap, 1989)"

Jan 1, 1994

By Z. Zhong, Y. J. Hu, D. Elsworth

"A standard triaxial apparatus was set up to perform sliding tests. Slide-hold-slide (SHS) tests, with hold times from 10 to 3000s and at invariant effective confining pressures of 1MPa, incremented to 3MPa and then 5MPa, were conducted on both dry and wet split limestone samples to study the evolution of fracture friction under holding and sliding processes. Limestone fracture shows time-dependent behaviors in SHS tests, friction drops (creep) gradually during hold periods, and recovers (healing) after re-slide. Frictional healing and creep increment are proportional with hold times, while are inversely proportional with effective confining pressures. Moreover, the wet sample displays heavier healing than the dry one, whereas creep increment of the wet sample is lighter than the dry one. We conclude that the evolution of limestone fracture friction is significantly controlled by mechanisms of fluid-rock interactions.INTRODUCTIONThe evolution of the mechanical properties of fractures and faults exerts a critical influence on the behavior of fault zones and on the earthquake cycle. In addition to natural processes, this behavior has broad implications in induced seismicity and influences oil and gas production, the sequestration of carbon dioxide and the disposal of nuclear wastes.Fault friction is typically measured by slide-hold-slide experiments, where fault gouge is deformed at low velocities (<0.1 mms-1) and over small shear offsets (<30 mm) (Dieterich, 1979, 1981; Mair et al., 1999; Marone, 1998, 2004) or alternatively with rotary-shear devices, that enable higher slip velocities over very large shear offsets (Hirose & Shimamoto, 2005; Mizoguchi et al., 2006). Typical experiments (Dieterich, 1972; Marone, 1998; Olsen et al., 1998; Bos & Spiers, 2002; Tenthorey et al., 2003) show significant creep during the holding period and frictional healing (strength gain) upon reloading. Fault creep and healing are often time-dependent with longer hold times typically resulting in greater magnitudes of creep and in strength gains (Tenthorey et al., 2003; Yasuhara et al., 2005; Carpenter et al., 2012). Frictional healing may arise from growth of grain contacts (potentially induced by pressure solution) (Rabinowicz, 1951; Dieterich & Kilgore, 1994; Yasuhara et al., 2005), strengthening of the contacts (correlates with cementation) (Hickman & Evans, 1992; Beeler et al., 1994; Karner et al., 1997; Olsen et al., 1998; Muhuri et al., 2003; Tenthorey et al., 2003; Li et al., 2011) or via other changes in state including changes in porosity and rearrangement of force chains. Experimental evidence (Dieterich, 1979, 1981; Johnson, 1981; Marone & Scholz, 1988; Marone, 1998; Saffer & Marone, 2003; Moore & Lockner, 2007; Ikari et al., 2007; Ikari et al., 2011; Carpenter et al., 2012) quantifies both the mode and magnitude of second-order changes in the velocity-dependent (including velocity- strengthening and weakening) evolution of frictional strength."

Jan 1, 2015

"An atmospheric process for the synthesis of scorodite(DMSP®)has beendeveloped,in which ferrous ions were oxidized by oxygen gas in the presence of pentavalent arsenic ions. Under optimum conditions, the synthesized scorodite (FeAsO4?2H2O) was well crystallizedand the crystals were faceted; the particle sizes were as large as 15 to 20 µm. In thisstudy, iron (II) sulfate heptahydrate (FeSO4·7H2O), arsenic (V) acid (60mass%H3AsO4) solution, and distilled water were used to prepare the original experimental solution (700 ml), in which the contents of Fe(II) and As(V) were 55.9 g/L and 50.0 g/L, respectively. The effects of various synthesis conditions, such as the type of oxidizing gas (oxygen or air), gas injectionrate, temperature, and the initial pH of the solution, on the size and shape of the scorodite particles wereinvestigated. From the experimental results, the changes in the shape of the scorodite particles wereclarified for each synthesis condition.INTRODUCTIONDOWA has developed a processfor synthesizing well-crystallized scorodite (FeAsO4•2H2O). Theprocess is named andtrademarked as DMSP® (Fujita et al., 2008; Fujita et al., 2008; Fujita et al., 2009; Fujita et al., 2009; Fujita et al., 2009, Kubo et al., 2010). In this process, oxygen gas is injectedinto a sulfuric acid solution containing large amountsof As(V) and Fe(II). Facetedscorodite crystals as large as 15–20 µm weregeneratedthrough the pre-formation of a gel-like precursor. However, it is known that the synthesized scorodite particles become smaller and more aggregatedwhen the synthesis conditionsdeviate from the optimumconditions.In this study, the effects of various synthesis conditions, such as the type of oxidizing gas (oxygen or air), gas flowrate, temperature, and initial pH of the solution, on the size and shape of the scorodite particles were investigated. The experimental resultsclarified the changes in the shape of the scorodite particles for each synthesis condition."

Jan 1, 2016

By Ning Yu

There are about 1.341 trillion tons (t) of proven coal reserves in China, of which 279.58 billion t are available for mine well construction basis. Thick coal seams are 44% of the reserves. The production of thick coal seams exploitation is over 45% of the total coal production. Full-seam mining and fully-mechanized mining for large mining height is the technology development direction of thick and extra thick seam mining. It is also the important way to achieve efficient and intensive mining with the characteristics of high production, high mechanization, high efficiency and low energy consumption, etc. Complete set of technology and equipment of fully-mechanized top caving for large mining height of full-seam (7m) mining and extra thick seam ( 14-20m) has been gradually mature and for demonstration application by the joint research of government, enterprises, universities, scientific research organizations and users. It has solved some technical problems of coal face for large mining height (over 7m) such as the coal wall spalling control, stability of support, wall rock coupling, cooperation work of mining and caving, full roadway support for super large section, end support, equipment matching of coal shearers, hydraulic support and scraper conveyor. It has developed key equipments including powerful hydraulic support of fully-mechanized mining and fully-mechanized top caving for large mining height, electrically-driven coal shearer with high speed and reliability, scraper and belt conveyer with big capacity, soft-start and high reliability, automatic control system of coal face with the core of electric-hydraulic control, bolting drill boom large section coal roadway shearer, heavy auxiliary transport equipment. The operation rates of fully-mechanized top caving equipment for full-seam and large mining height are 94% and 92.1%, and recovery ratios are 93.6% and 88.9% respectively. The annual raw coal production of single work face is over 10 Mt. The automation and intelligentization level have been clearly improved. The exploitation of thick and extra thick coal seam that is safe and efficient has been achieved in China.

Aug 1, 2013

By B. P. Verma, K. N. Sinha, N. M. Raju, B. Singh

The paper describes a new method of grouting bolts developed at the Central Mining Research Station at Dhanbad in India. This method makes use of wire-mesh sleeve instead of the expensive metal tube to insert the cement mortar into the drill hole. The field trials confirmed that the method is cheap and an effective system of support.

Jan 1, 1972

By I Wilkomirsky, F. Parada, R. Parra, E. Balladares

"The neutral roasting of As bearing copper concentrates is confirmed well established and promising option for the treatment of this type of complex concentrate. The AS elimination by volatilization allows subsequent treatment of the calcines produced in a conventional pyrometallurgical process, by blending this product with standard concentrates.Several tests were performed using the fluidized bed pilot plant at the University of Concepción with different types of concentrates. Calcines, fines from two hot cyclones and flue dust from the ESP were collected. These materials were characterized using QEMSCAN® and the results used for the development of a mass and energy balance which took into consideration the specific chemical transformations that occurred in the reactor.A physico-chemical/kinetic model is proposed to explain the formation of bornite, chalcopyrite and magnetite. The mechanism involves solid-gas reactions between chalcocite, pyrrhotite and gaseous sulfur that without the mineralogical characterization would not have been possible to propose"

Jan 1, 2014

By K. E. Waters, C. Marion, T. Grammatikopoulos, A. Jordens

"The Nechalacho deposit, located in the Northwest Territories, Canada, is a heavy rare earth element (REE) deposit. The main REE-bearing minerals in the deposit are zircon, allanite, bastnäsite, synchysite, columbite (Fe) and fergusonite. Previous work investigated the use of gravity and magnetic separation in the processing of this ore and showed that coarse particles following grinding were enriched in zircon, suggesting the potential for selective comminution. The current work investigates the possibility to selectively comminute gangue minerals and concentrate REE-bearing zircon into coarser size fractions. The ore was ground wet in a laboratory rod mill for various lengths of time (0, 10, 20, 30, and 40 min). The resultant products were analyzed using ICP-MS, to determine the distribution of zirconium and REEs in the different size fractions produced after grinding, and QEMSCAN, to identify mineral phases, mineral liberation and the distribution of minerals. Optimum grind sizes for the upgrading of zircon due to selective comminution were then proposed, and dense medium separation was investigated as a means to further concentrate zircon.It is important to note that this process is not representative of the currently selected process design or recovery for the Nechalacho deposit. Any application of this process to this deposit would require optimization in order to ensure appropriate grade and recovery targets are met.INTRODUCTIONThe rare earth elements (REEs) are the fifteen elements in the lanthanide series of the Periodic Table, as well as yttrium (scandium is excluded in this work). Traditionally, REEs are categorized into two groups: the cerium sub-group of “light” rare earth elements (LREEs); and the yttrium sub-group of “heavy” rare earth elements (HREEs) (Golev et al., 2014). The LREEs comprise the first six lanthanides (lanthanum through samarium) and the HREEs comprise the remaining nine lanthanide elements (europium through lutetium) coupled with yttrium (Golev et al., 2014). HREEs are much less abundant in the earth’s crust and on average are more expensive than LREEs (Seredin, 2010). Of the fifteen REEs, the production of neodymium, europium, terbium, dysprosium and yttrium has been determined to be most critical due to their scarcity, high demand and criticality in many high-technology and clean energy applications, such as in illuminated screens for electronic devices and permanent magnets in wind turbines (Seredin, 2010; U.S. Department of Energy, 2011). These five elements are classified as critical rare earth elements (CREEs) (U.S. Department of Energy, 2011)."

Jan 1, 2016

By Steven R. McCutcheon

"The Bathurst-Newcastle district, a subcircular area approximately 50 km in diameter, contains 37 massive-sulfide Zn-Pb-Cu deposits that have defined tonnages, and has 58 additional significant occurrences. The largest deposit is Brunswick No. 12, with total reserves (including past production) of 148 million tonnes grading about 12.5% combined Pb-Zn. The deposits/ occurrences are spatially associated with a felsic volcanic pile that contains a significant sedimentary component. In the vicinity of the Brunswick deposits the pile is divisible into lower and upper sequences. The lower is characterized by megacrystic rhyolite (QFAS) and coarse- to fine-grained quartz (± feldspar) wackes and/or tuffites (QAS); the upper sequence is characterized by aphyric to sparsely porphyritic rhyolites (HWR), micro-breccias, and acid hyaloclastites with interbedded dark gray sedimentary rocks. A greenish gray to dark gray siltstone (GGS) separates the two sequences and hosts the sulfide deposits. Lithogeo chemistry of least altered samples shows that the QFAS and HWR have an igneous character, whereas the QAS and GGS have a sedimentary signature. The two types can be distinguished on the basis of total alkalies (Na2 + K2O) versus SiO2/Al2O3 and Ti02 versus Fe/(Fe +Mg). Some trace elements, such as Sr and Y, also help differentiate the two types. The QFAS differs from HWR by having higher La/Yb ratios but lower Zr and Th. The Bathurst deposits do not show a close spatial association with rhyolites but rather are stratiform bodies Oacking clastic textures) within fine-grained sedimentary rocks. The scarcity of barite and other sulfates indicates that there was little mixing between the metal bearing fluids and cold seawater. High Fe/(Fe+Mg) ratios in chlorites also indicate the fluids did not contain a significant seawater component. These features and the large size of many deposits suggest that the deposits formed from metal-rich pore waters that were released catastrophicallyfrom an acquifer in the footwall stratigraphy."

Jan 1, 1992

By L. H. Rajala, K. H. Singh

"This paper presents the results of a detailed feasibility study carried out to investigate whether a low-grade deep underground mine of Falconbridge Nickel Mines Ltd., closed since 1975, could be made more productive and profitable by the introduction of new mining technology. For this purpose, recent advances in mine design and development concepts, larger and better designed machines, such as hydraulic drills, high-pressure down-the-hole machines, LHDs, new blasting concepts, more efficient and improved stoping methods, and ground control technology were considered. Technical and economic analyses incorporated the latest computer-based techniques. The mine was reopened in 1979 and the paper concludes with an assessment of actual progress and performance compared with that planned and forecast.IntroductionThe East Mine orebody, located between the Falconbridge Mine and Inco&apos;s Cryderman Mine in the Sudbury District of Ontario, has been in production since 1956. From 1956 to 1978, about 5.6 million tons of ore had been mined from this ore zone. The ore body is low grade and was developed as a cut-and-fill operation. Due to high operating costs, the mine has been shut down several times during economic downturns. The latest closure was in 1975 due to a lower demand for metal.In 1978, investigations were initiated to assess the economic and technical feasibility of mining this ore using new developments in mining technology. In this study, consideration was given to the application of bulk mining methods with a potential for higher productivity, trackless development utilizing efficient LHD machines and hydraulic drills, new blasting and fragmentation concepts, and new ground control technology. Advanced computer techniques, such as finite element, for mine design and rate of return with discounted cash flow analyses for the economic comparison- of various mining options were utilized for a rapid and comprehensive assessment during the feasibility stage."

Jan 1, 1981

By A. C. Hatton

Doped SrCoO3.8 was found to be a promising material for use as a cathode component in intermediate temperature SOFCs. In this work, strontium cobaltite ceramics doped with 10 mol% to 90 mol% samarium were synthesized using the glycine nitrate process in order to study the electrical conductivity and thermal expansion at temperatures of up to 800°C. As-synthesized powders were deagglomerated, pressed and sintered at temperatures ranging from 1100-1250°C. The effect of temperature and composition on electrical conductivity and thermal expansion are presented and discussed.

Jan 1, 2005

The influence of joint orientation and joint persistence, on the mechanical behaviour of jointed rock masses under uniaxial compression, has been studied systematically. The joint inclination angle ß was varied from 0° to 90° with an increment of 15°. The joint continuity factor k was taken as 0.2, 0.4, 0.6 and 0.8. The peak strength, Young’s modulus, the complete axial stress-axial strain curves, the cracking process and the characteristic of the fragments, were investigated. It was found that the anisotropic response of the jointed specimens was governed by the micro-mechanism, such as crack initiation, propagation and coalescence, crack opening or closing, and frictional slip of cracks or joints. With the increase of joint continuity factor, the axial stress-axial strain curves change from single-peak to multipeak, the peak strength and Young’s modulus decrease. The specimens with medium joint inclination angle (30°,45° and 60°) has lower energy dissipation and strength due to stepped or shear failure, while specimens with small and large joint inclination angle (0°, 15°, 75° and 90°) has higher energy dissipation and strength due to axial cleavage or crushing failure.

Jan 1, 2015

By Hang Zhao, Xinping Li, Pingan Wu, Yi Luo

The deep-buried rock surrounding the Jinping II Hydro-power Station was taken as the engineering background. Using model specimens of classified rock materials to simulate fractured rock mass under high in-situ stress conditions, the test about acoustic propagation law on single fracture model of specimen under different pressures and different angles were carried out. The variation of p-wave velocity in fractured rock mass and axial stress-strain relationship in the whole test procedure was also studied. Based on damage mechanics principle and the acoustic wave propagation in cracked rock mass, comparative study on damage constitutive relation of fractured rock mass under high in-situ stress in consideration of equivalent strain and equivalent energy was performed. As the results showed, with the change of axial stress level under constant confining pressure, the change in wave velocity can be divided into three stages: slow increase (small variation in amplitude), rapid reduce (large variation in amplitude ) and accelerate reduction. When the confining pressure is constant, the maximum p-wave velocity and the peak strength of specimens increases with the decrease of the crack angle. When the crack angle is constant, the maximum p-wave velocity and the peak strength of specimens increases with the increase of confining pressure.It is identified that the theoretical calculation results of constitutive relation about elasto-plastic damage model containing variable wave velocity in the fractured rock mass is consistent with the model test results.Therefore,the constitutive relation can provide reasonable suggestions for engineering practice.

Jan 1, 2015

By Gulshan Kumar Pradhan, Yogendra Pratap Singh, Dhawanm Nikhil

"Potassium (K) is one of the essential elements for the growth of plants and thereby for humans. In fertilizers, potash demand has been steadily increasing at ~3.5% annually. Water soluble potash deposits are rare and highly localized. India is neither present on the world potash production map nor it has adequate potash rich rocks. The K-bearing minerals are recovered either by using conventional underground mining methods or though solution mining methods. India possesses a vast resource of silicate rocks such as glauconitic sandstone and Feldspar. These rocks are basically a group of alumino silicate of potassium, sodium and calcium (K2O%: 5-12, Na2O%: 3-10%, SiO2%: 52-65, Al2O3%: 15-20, Fe2O3%:, 5-7 and MgO%: 2-3.5).The K extraction from silicate rocks has received little attention probably due to the slow release, the locked structure of alumina-silicate minerals, and the unavailability of appropriate economic processes & their know-how. In fact due to this India imports all of its potash demand (about 3.5 million tons per annum) from different countries.In the present work, an attempt has been made to identify the structural and chemical alteration of desired K mineral phase in silicate rock (~K2O%: 10.5, Na2O%: 2%, SiO2%: 55, Al2O3%: 19, Fe2O3%, 5-6, MgO%: 2.5) under different conditions such as acid leaching, thermal treatment and chemical processing. Different treatments are aimed to increase K availability which is related to the modifications in mineralogical composition. The modifications in the feed sample and treated samples are studied through SEM-EDAX, XRD, EPMA and optical microscope. With the combination of treatments, it is possible to extract more than 90% K and the formation of sylvite phase (water soluble) confirms the dissolution of potash values."

Jan 1, 2016

By R. K. Jonas

Many leading copper and other mineral processors have rapidly adopted advanced controls in last 5-10 years. Almost 600 multivariable predictive controls have been installed in mineral processing, and almost 50% of those are in copper concentrator plants. In most cases, mineral processors rely on 3rd party support to implement these advanced technologies. One challenge facing advanced control user is the selection providers and services for these technologies. The trend has been towards the use of multivariable predictive control and use of technology provider’s services. This paper will discuss status of advanced control, and the merging trends in the mining industry. A review will be presented of how advanced control is being applied in the mining industry over the last decade, and how user challenges are being overcome. Next the emerging uses of multivariable predictive control (such as multi/inter-unit optimization), focusing on the latest trends in concentrator plants. Finally, a review will be made of emerging technology advances in the that can be advantageous to mineral processors. INTRODUCTION Review of advanced control in mineral processing Advanced controls are serving an increasing role to improve processing plant operations and profitability. As advanced control is being installed into more mining processing plants such as copper concentrators, many of these plants are concerned about the selection technologies and vendors to support the installation and maintenance of these controls. In a study by Jonas and Craw (2011), they found that most new users have not had prior experience with advanced controls. It is the author’s experience of almost 30 years in advanced controls that most mineral processers considering advanced controls can benefit from better understanding of the technologies and their support requirements.

Jan 1, 2019

By Shahé Shnorhokian

Numerical modeling is increasingly being used as a tool to examine complex geomechanical issues related to rockmass behaviour and stability of underground openings. The in-situ stress regime and the evolution of mining-induced stresses during the life of an operation, taking into account the planned stope sequence, are topics that can only be handled through the use of a realistic and calibrated numerical model. This paper presents a case study of a deep underground Canadian mine in northern Ontario. A FLAC3D model was constructed and calibrated based on in-situ stress measurements. In the first stage, the evolution of stress regime was studied and compared with the occurrence of rockburst events during a period of three years. The locations of clusters were examined and compared to the mining sequence during that period. In the second stage, stresses within a diminishing ore pillar were examined based on the planned stope sequence and compared to levels deemed acceptable to the mine. Based on the results, an alternative sequence was arrived at to reduce stress accumulation in the pillar, or induce it to occur at a further distance from a brittle dyke in the vicinity of the orebody.

Aug 1, 2013

By John C. McKay

"The five papers which follow, under the heading of ""Technology Transfer-Universities to Industry"", were originally presented at the 20th Annual CIM Conference of Metallurgists in Hamilton, Ontario. They are a unique group of papers, unique because each paper is concerned with applied research done wholly or partly in a university environment and then translated into industrial practice.Universities can rightly be regarded as one of our nation&apos;s greatest resources-a veritable storehouse of knowledge and expertise. Yet, too often, this resource is overlooked or, at best, sparingly used by Canadian industry. Of course, university-based research cannot supplant industry-based research, nor vice versa; each type of research activity has its proper role in the over-all process of technology development.University-based scientists are best equipped to conceptualize, innovate, determine viability of basic premises and to verify these at the bench or small pilot-plant level. Industry based scientists are best equipped to develop ""bench-scale"" innovations into mature manufacturing practices. Thus, university-based scientists and industry-based scientists do not compete with, but rather complement, each other. Active, relevant university research enhances industrial research provided good communication between the two ""solitudes"" is continually nurtured.Good communication between industry and university is a prime objective of CSIRA/ACRIS (Canadian Steel Industry Research Association /Association Canadienne pour la Recherches dans d&apos;Industrie Siderurgique), The directors of CSIRA/ACRIS foster improved communication by making regular visits to universities, by sponsoring projects and by providing lists to professors of uncharted areas where basic research is needed. More can be done to improve communication between industry and university, and it is the intent of the Association to do more.The five papers sponsored by CSIRA/ACRIS are examples of good communication and healthy cooperation. It is interesting to note when reading these papers that the cooperation arose, in each instance, as a result of different circumstances. However, there is a common thread and it is personal acquaintanceship-the university scientist/professor and the industry investigator/manager knew each other prior to the initiation of the project."

Jan 1, 1982

By J. F. Wang, Y. Jin, Z. L. Wang

Smelting reduction as an ironmaking technology for the 21st century has been challenging the traditional blast furnace. The process has many attractive advantages over the blast furnace, however, the massive by-produced coal gas mainly containing CO, H2 and CO2 requires further treatment. From a chemical engineering view, coal gas is a valuable chemical stock and can be transformed into hydrogen-rich synthesis gas. Hydrogen can be directly used as clean fuel and synthesis gas can be used for the production of some important chemicals such as methanol, ammonia and dimethyl ether. Among those chemicals, dimethyl ether as an alternative clean fuel for diesel engine and liquefied petroleum gas has been drawing more attention. It has excellent environmentally-benign behaviours not only in compression ignition combustion, but also in the much lower emission of SOx and NOx. In this work, a combined technology of smelt reduction ironmaking and direct synthesis of dimethyl ether, which will strongly promote the energy efficiency, environmental protection and resource recovery, is proposed and described in detail.

Jan 1, 2004

By N. Dahata

B206 aluminum?copper alloy has a potential for wider use in the automotive industry due to its light weight and relatively superior mechanical properties as compared to aluminum-silicon alloys. The possibility of casting this alloy via Lost Foam Casting (LFC) has not been investigated in detail. Therefore, the effects of foam types (T170B standard untreated EPS and T175-brominated EPS), coating types (Styro Shield 5553 and Styro Shield 5554), copper level (4.5 wt % and 5.0 wt %) and titanium levels (0.5 wt % and 0.25 wt %) were related to fillability, microstructure and microporosity. The metal velocity in T175 EPS pattern was higher than that in T170B EPS pattern. For T175 EPS pattern, the total solidification time was 3% higher and the loss of temperature for decomposition of EPS was lower than those in the case of T170B EPS pattern. The grain size, porosity level and maximum pore size were quantified using Light Optical Microscopy (LOM) and image analysis. The casting with T175 EPS pattern showed larger grain size relative to that with T170B EPS pattern. The porosity level and the maximum pore size decreased significantly when the titanium level was increased from 0.05 wt % to 0.25 wt %.

Jan 1, 2007