Search Documents

By R. R. Rogers

Introduction The subject of cathodic protection is not new. In 1824 Sir Humphry Davy, in publishing the results of his investigations for the British navy, pointed out that copper could be protected from sea-water corrosion by connecting it electrically with zinc or iron. Since that time much work has been clone in this field, particularly in the protection of metals from the action of sea water, neutral brines, and treated and untreated waters. Special mention should be made of the successful protection of underground pipe-lines which formerly were badly corroded by the water in the ground. So far, magnesium alloy and zinc anodes have been the most popular. However, fairly recent work has indicated that aluminium anodes will give good service under certain conditions. The principle of cathodic protection has been applied extensively in coating steel articles with zinc and in cladding aluminium alloy sheet with pure aluminium. A valuable discussion of the fundamentals and applications of cathodic protection recently was presented in the Corrosion Handbook. A useful list of references was included in the article.

Jan 1, 1949

By Ki-Bok Min, Bona Park

"In spite of the applications of DEM models to emulate the elastic modulus, Poisson’s ratio and strengths of isotropic rock in laboratory scale, extensions to anisotropic rock and larger engineering scale still have many challenges to overcome such as robust verification and validation against observed field case. In this study, a discrete element modeling was performed in order to represent a transversely isotropic rock such as shale, and the upscaled model was applied to foundation and borehole problems using PFC2D. The applicability of the upscaled rock mass model was verified by an analytical solution. The DEM modeling of stress redistribution induced by an applied surface line load compares well with Boussinesq’s isotropic solution and anisotropic solution given by Bray. The borehole model with a circular opening under biaxial stress was compared with both isotropic and anisotropic solutions resulting in good agreement. The abilities of DEM model to investigate the micromechanisms accounting for complex macroscopic behaviors and to predict the macroscopic behavior are discussed.The results demonstrate that DEM modeling has the potential to be applied to anisotropic rock mechanics problems on larger engineering scales such as wellbore stability problems especially in shale formations. Furthermore, the effect of anisotropy modeled through this study may be able to explain failure behavior of anisotropic rock encountered frequently in real cases.INTRODUCTIONAnisotropy is prevalent in various types of rocks, especially in shale that contain a set of parallel bedding planes. These weak planes in various forms are sources of large deformation and low shear strength and contribute significantly to the anisotropic behavior of rocks (Amadei, 1996; Cho et al., 2012; Kim et al., 2012). As elastic and strength behavior of anisotropic rock is substantially different from that of isotropic rock, proper consideration of anisotropy is of great importance. There is extensive of experimental evidence showing the anisotropy of shale. Niandou et al. (Niandou et al., 1997) analyzed the plastic deformation and failure mechanisms of Tournemire shale were highly dependent on the orientation of bedding planes. Cho et al. (Cho et al., 2012) presented various deformations and strengths of Boryeong shale obtained from laboratory experiments. Fjaer and Nes (Fjaer and Nes, 2013) performed uniaxial and triaxial compressive strength tests using Mancos shale, and they observed that the shear sliding along the planes of weakness before the occurrence of a major failure can reduce the strength of anisotropic rock. The recent research has demonstrated that the anisotropy of rock is an important consideration in rock engineering."

Jan 1, 2015

By R. B. Taylor

"The Delnite mine is in the northwest part of Deloro township, Cochrane district. The property consists of 307 acres on the so-called 'South Break' in the Porcupine camp. The Company was formed in 1934 to take over the holdings of La Roche Mines, Limited. Gold has been produced continuously since June 1, 1937. The value of the gold recovered to date (December 31, 1946) has been $7,456,000, and the average grade of ore $6.81 a con.The ore at the Delnite occurs in relatively narrow, persistent, quartz-ankerite veins, which generally contain tourmaline and have a ladder-like structure. The gold occurs in the free state, and in association with pyrite and arsenopyrite, the two chief sulphides. The host rock is fine-grained, highly carbonatized andesite of Keewatin age."

Jan 1, 1954

By Zia Pirzada

"Time is of the essence" and "Time is money" These are powerful and true statements during a project life cycle and have far-reaching implications on the success and failure of the project Time and progress management is crucial to the project success. Project delays may increase the cost to an unacceptable level and may render the project as economically unfeasible. On the other hand, if the project is completed on time or earlier than as planned, it may generate economic benefits greater than what had been envisioned To take advantage of the financial opportunities and to improve the cash flow as well as Return On Investment (POI), project schedule can be accelerated to complete the project earlier than planned Project schedule acceleration can be achieved by using analytical tools, such as "Schedule Optimization", "Schedule Reduction", "Schedule Compression" or a combination of any of these concepts along with the "Planning for start up". Schedule optimization does not entail any extra cost, however, other acceleration methods, such as Schedule Reduction and Schedule Compression, may require extra expenditures from the owner. Based on the forecasted early start of the revenue stream, the extra expenditure could become a worthwhile venture with a very high rate of return To accelerate the schedule, all aspects of the project should be reviewed with acceleration costs calculated. All risks and opportunities should be evaluated and taken into consideration to determine if the acceleration is feasible and advisable and will provide definite financial advantages Sometimes schedule acceleration may be desired to prevent the company from paying liquidated damages. This is especially true when the project is not expected to complete on the contractual completion date and when the cost of acceleration is less than the liquidated damages that may accrue against the company.

Oct 1, 2010

By A. W. Johnston, R. E. Barrett

"The Central Patricia mine is in the greenstone belt north of lake Sc. Joseph in northwestern Ontario. It is 90 miles north of Allanwater on the Canadian National railway and 220 miles east of the Manitoba boundary. The unusual feature of the ore of this mine is that the gold does not occur in quartz but in sulphide minerals filling fractures in iron formation.AREAL GEOLOGYThe rocks of the area in which the mine occurs belong to the Early Precambrian. They consist · of andesite lavas and tuff interbedded with greywacke-like sediments and iron formation . A siliceous phase of the sediments lying north and south of the greywacke enclosing the ore-bearing iron formation in places resembles a sheared and sericitized quartz porphyry. This is shown in the legend of Fig. 1 as quartz porphyry and quartzite, but it is possible that the quartz porphyry-like phase is sediment. A northwest- striking dyke of diabase crosses the property 3,000 feet east of the shaft ( Fig. 1).IRON FORMATIONAlthough there are numerous bands of iron formation in the v1cm1ty of the mine, ore has been found to date in only one main and two lesser zones. The iron formation bands range in width from a few inches to 60 feet, and are interrupted along their strike by gaps that are parallel and rake to the east at about 65°. The iron formation is definitely banded and laminated."

Jan 1, 1954

By D. Nie, M. Ren, T. Mo

This paper studied the phenomenon of room temperature creep deformation at crack tip and its effect on fatigue crack growth rate of a X-70 pipeline steel using compact-tension (CT) specimen on a MTS 810 testing machine. Time-dependent deformation at the crack tip under constant load was observed in this steel at room temperature and the amount of deformation produced was seen to depend on loading rate and the magnitude of stress intensity factor. It is found that there exists a critical stress intensity factor below which the deformation decreases with time when the applied load remains constant. It is also found that the occurrence of room temperature creep obviously affects the subsequent fatigue crack growth rate. The observed behavior was explained based on dislocation theory.

Jan 1, 2005

By R. S. Jr. Stronach

"IntroductionThe property of Campbell Red Lake Mines, Limited, is in Balmer township, Red Lake area, Patricia portion of Kenora district, Ontario. It consists of a group of twelve claims which had been staked and re-staked a number of times before George W. and Colin A. Campbell staked them in 1944. Messrs. Brewis and White incorporated Campbell Red Lake Mines, Limited, in July, 1944, to acquire these claims from the Campbell brothers, and in November of the same year re-assigned their option on the controlling interest of the treasury shares to the Dome Exploration Company (Quebec), Limited, a wholly owned subsidiary of Dome Mines, Limited.A long known exposure of sulphides on the northeasterly portion of the property, which returned low gold assays, on sampling, was the only showing of interest at this time. However, Dr. H. C. Horwood's report and map of the district had recently been published and favourable structure W3.S indicated in Balmer township. It was on the strength of this showing and Dr. Horwood's report that Dome Exploration became interested in the property.Between. January, 1945, and April, 1946, a diamond drilling programme was carried out, with completion of sixty-one holes. Five holes proved the surface showing to hold no commercial interest, so routine cross-sectioning of the property from north to south was started. The fourth hole of the series returned excellent ore intersections and from that time on the programme changed to one of extending these values. The final results of the drilling showed that what is now known as the A zone has a continuous length of some 1,200 feet, a width of 4½ feet, and an overall grade of about 0.5 oz. gold per ton. There were many other intersections of ore grade outside this A zone which could not be successfully correlated .at that time, but underground work has opened many of them. It may be said here that practically all the work to date has been confined to the southeast claims of the property."

Jan 1, 1950

By Alexander Potapov, Lawrence Nordell

A Conjugate Anvil-Hammer Mill (CAHM) has the potential to replace conventional crushers and SAG mills, with their respective conveyors and stockpiles, in a SABC circuit. It may improve comminution circuit efficiency by 100%. CAHM compresses rock in a more efficient way, similar to 19th century stamp mills, which follows the fundamental research of Schönert (1990 & 1996). CAHM efficiency is being proven through the use of ROCKY (2011) Discrete Element Method (DEM). ROCKY features allow it to simulate realistic comminution. CAHM is customizable with many geometries that are rock-property specific. ROCKY’s wear modeling compliments the structural integrity of the design.

Jan 1, 2012

By A. Mular, T. Bond, G. D. Farnell, J. F. Kingston

"ABSTRACT:-A 60—cm semiautogenous grinding-(SAG) mill was designed -for continuous wet operation in closed circuit with a vibrating screen. The circuit is fully instrumented and automated. Part of the control system incorporates Foxboro SPEC 200 controllers around the pump box to maintain level. The rest of the control system involves an ACTION model BC2 basic direct digital controller that handles all other inputs/outputs and contact closure sensing:·The success of the control system is attributed to the uniqueness of specially designed mass flow metering systems. Various control strategies are possible. Employed to date has been control of a mill load set-point by cascading the deviation from load set-point as the set-point to the fresh feed rate ""controller"". Mill feed water is ratioed to total flow rate of solids fed to the mill. The performance of the circuit is being correlated with the performance of full scale SAG circuits in British Columbia to develop models, to assess the feasibility of scale up and to investigate the effects of design variables on responses such as circuit throughput. 1 INTRODUCTIONWhere ore types are appropriate, semiautogenous grinding and/or autogenous grinding (AG) has replaced conventional grinding. Secondary/Tertiary crushing plants are thereby eliminated so that capital expenditures are less and overall comminution costs can be lower (Barratt 1982). To establish the suitability of an ore for SAG circuits, pilot scale tests with 1.7 to 1.8 M diameter mills are often conducted. At least one test per ore type in a deposit has been necessary. Often, each test involves a large amount (up to 50 tonne) of sample, so that the testwork can be expensive and may discourage the use of SAG or AG circuits. However, MacPherson (1977) has employed a continuous 45 cm dry Aerofall mill circuit closed with screens and an air classifier to determine whether ores are suitable for SAG milling. The amount of sample per ore type is of the order of 60 kg or less. Thus an established SAG mill scale up procedure that employs small circuits is highly desirable.The purpose of this paper is to describe a small 60 cm wet continuous SAG/ AG mill pilot circuit assembled at the University of British Columbia to study the feasibility of scale up, to assess the influence of design variables, to develop mathematical models and to evaluate the effects of alternative control strategies on circuit performance"

Jan 1, 1988

By Jochen Franke, Matt Bird, Thoma Perkins, Malcolm Powell, Jason Robertson, Paul Toor

zThe operation of SAG mills is variable over time due to their continually changing liner shape, mass and subsequent load motion. However, this tends to be poorly accommodated in liner design and mill control, with only limited compensation made for this influence, usually in the first few weeks after a new liner is installed. With ever-increasing ore competency, increasing energy costs and decreasing ore grades, simplified design and operational approaches that compromise the achievable mill efficiency are no longer adequate. This paper presents a methodology that has been developed to measure and account for the changes in mill performance as the liner wears. This involves monitoring all liner profiles – in other words the three-dimensional liner shape - over the life of the liner, then conducting controlled surveys at different stages of the liner wear life, and correlating the mill performance to the liner profiles. The measured liner mass is modelled to provide an ongoing meaningful load mass measure that excludes the liner mass.

Jan 1, 2012

By E. Stansfield

Coal samples are sometimes taken from a wet spot in a mine, or from an open car or pile shortly after rain, and submitted for analysis in a dripping wet condition. Other samples are taken from a dry spot in the mine, or from an open car or pile after a period of dry weather. Comparison of the analyses obtained in the two cases would be absurd, although the samples might be of essentially the same coat apart from the surface moisture on the one. The analyst therefore attempts to reduce all samples to an equal basis by the operation known as air-drying. Air-drying is practised by the chemist for three reasons: (1) To make it possible to grind the coal to powder. (2) To bring the coal sample to a condition in which it will not change in weight rapidly whilst portions are being weighed out for analysis -in other words, to bring it into equilibrium with the air in the laboratory. (3) To determine the water-retaining power of the coal. Any kind of drying is satisfactory for (1); the coal should be dried more or less according to the humidity at the time in the laboratory for (2); whilst it should be always dried to the same extent for (3). In other words, no method can be satisfactory for both (2) and (3). In this paper the only question considered is (3) -that is, air-drying the coal under standard conditions so that strictly comparable results can be obtained for the water content of coals after air-drying. After a sample of wet coal is exposed, it loses moisture until it is in equilibrium with the air at the time: thus the coal will loose distinctly more water in air of 20 per cent relative humidity, for example, than it would in air of 80 per cent.

Jan 1, 1923

By A. F. Gregory

"AbstractA resumé of aerial radiation survey studies performed by and for Eldorado Mining and Refining, Limited, since 1943 is presented. Flight tests were initiated in 1947 and were followed .by intensified use and study of Geiger counters and other radiation detectors. Development of an aerial scintillation counter began in 1948, but •a sensitive large crystal unit was not available for exploration purposes until 1950. Modifications of this unit have been used in all subsequent surveys.For the Eldorado detector, several limiting conditions were established for successful radioactivity detection, the most important being that natural vein exposures can only be assuredly detected .at distances less than 150 feet. Sedimentary and pegmatitic radioactive occurrences can be detected at much greater distances. A helicopter investigation technique appears to •have •a useful prospecting potential.IntroductionAerial radiation surveys were first proposed in the early 1940's. However, it was not until 1949 that airborne detectors were extensively used in the search for radioactive minerals. Eldorado has flown about 50,000 miles of exploration flights, exclusive of tests, using a variety of •detectors and aircraft. Considerable data have •been gathered for .the evaluation of the several techniques employed. Much of the early work was performed with the co-operation of the National Research Council of Canada ( 1). More recent work was done in conjunction with the Commercial Products Division of Atomic Energy of Canada, Limited. The Development Department of this latter corporation designed and built the scintillation counter used in recent Eldorado surveys."

Jan 1, 1955

By S. H. Seyedein

A mathematical model was developed to study fluid flow and solidification in a single-roll casting system. Fluid flow coupled with energy equations were solved numerically using a finite volume method. A body-fitted coordinate transformation technique was adopted to handle the irregularly shaped domain. In order to couple the continuity and momentum equations, a SIMPLEC algorithm was used. A fixed-grid enthalpy method was considered to model the solidification in the system. The turbulence effect on flow field was modeled using a low-Re k-e model The model developed in this work was further run under various conditions to optimize the operating parameters of the process.

Jan 1, 2004

By S. Vaidya, R. C. McKellar, N. K. Sinha

Nominally [001]-oriented nickel-base single crystal (SX) superalloy CMSX-10 was investigated at 900°C under constant load, equivalent to an initial stress of 700 MPa, for creep strains from 7% to fracture strain (18.2%). The cross-sectional dimensions of initially uniform cylindrical specimens were measured along their entire length after the tests. The cross-section changed from circular to near elliptical shape. The anisotropic deformation, measured in terms of eccentricity, increased with the increasing strain level, but for a given strain level, it remained constant along the entire length of the initially uniform gauge section. The results are discussed in terms of diameter, eccentricity, area, local stress and microstructural observations. The most striking observation was the fact that all the specimens displayed a yoke-like shape, or the reduction of cross sectional area, at two locations within the originally uniform gauge section. Such observations have not been reported in the literature for single crystal superalloys.

Jan 1, 2006

By A. B. Irwin

"Discussion at MeetingDR. D. DERRY (Ventures Limited) referring to the diagram (Figure 15) which shows a transverse structure section across the Central Slocan area, asked what the assumed structure at depth was, remarking that dips are steeper and more uniform at depth and that the contortions with gently-dipping axial planes are at higher elevations. He wondered whether the section represented ,part of a very large fold with steeply-dipping axial plane.MR. J. D. LITTLE (Canadian Exploration, Limited) replied that E. B. Mayo (Kelowna Exploration Company) and others had considered that the entire section illustrated faces to the southwest and represents part of the lower limb of a great overturned •syncline which is concave toward the southwest.DR. R. DEWIT (Geological Survey) remarked that the photograph of a ripple mark (Figure 7) showed internal lamination conformable to the ripple mark and wondered if the structure was not due to slumping during consolidation, since the normal mode of formation of ripple mark would seem to preclude the possibility of such internal stratification.MR. LITTLE remarked that in his opinion such structures should not be depended upon alone with-out other confirmatory evidence of the direction of tops of beds."

Jan 1, 1952

By I. S. Zajac, Y. O. Oyediran, M. C. Robart

This paper presents an overview of the metallurgical work on the Strange Lake Alkalic Complex (SLAC), from historical development of the "Main Zone" to present day develoment of the "B Zone". The SLAC, originally discovered by the Iron Ore Company of Canada (IOC) in the northeastern Canadian Shield of Québec and Labrador, is one of the world’s largest deposits of rare earth elements (REE) including yttrium and high field strength elements (HFSE) including zirconium, niobium, and titanium. It is part of a Precambrian, post-tectonic complex of peralkaline granites which intruded along the contact between gneisses and monzonites of the Churchill Province of the Canadian Shield. Mineralization of interest at Strange Lake principally occurs within peralkaline granite-hosted pegmatite and aplite sheets and, to a lesser degree, within the host granites, particularly in intra-pegmatitic granites. The highest grade and metallurgically most favorable mineralization is in the upper, open pit mineable parts of the SLAC. Metallurgical development has been conducted under a number of mining companies, and various value metals have been targeted throughout the history of the deposit, including yttrium, zirconium, niobium, and rare earths. Historic processing routes tested have included ore beneficiation, atmospheric leaching, solvent extraction (SX), and metal precipitation. This paper also presents the metallurgical development supporting Quest Rare Minerals Ltd.’s (Quest) 2013 Pre-Feasibility Study (PFS) and 2014 Preliminary Economic Assessment (PEA).

Jan 1, 2014

By T. -W. Hong, Y. Son, S. -J. Hong, D. Choi

The characteristics of indium-tin-oxide (ITO) nanoparticles recovered from TFT-LCD panel scraps were investigated. The ITO was separated from TFT-LCD panel scraps by dissolving the color filter layer located between the ITO layer and the glass substrate. The solution was filtered to separate the ITO from the color filter component, and the filtered ITO was dissolved in the acid solution. ITO nanoparticles were then precipitated with ammonium hydroxide and organic dispersing agent, followed by heat-treatment at 600 °C. HRTEM, EDX and XRD analyses revealed that the 20 nm sized particle were composed of 90 % In and 10 % Sn, and were well crystallized to in the (222) preferred orientation.

Jan 1, 2014

By Rolf Andreas Lauten, Guy Kluck

"Formation of scales may have important detrimental effects in many mineral processing applications. A well-known problem is the need for frequent maintenance to remove scale from processing equipment. Another challenge may relate to encapsulation of valuable minerals in precipitating scale. In this work, we explore the ability of some crystal growth inhibitors to prevent or lower the degree of scale precipitation. In many situations pregnant leach solutions contains substantial concentrations of calcium, magnesium, sulfate and carbonate in addition to dissolved valuable elements, e.g. gold, copper, zinc. Together with non-dissolved gangue minerals, some slurries may also contain particulate gold, copper etc. During normal processing of the pregnant leach solution it may be exposed to temperature gradients or similar promoting precipitation of various scales. Valuable minerals may become entrapped in precipitates and thus become inaccessible to the lixiviant. Use of a crystal growth inhibitor may lower the degree of encapsulation of valuable elements.Using a simple model system, supersaturated with respect to gypsum, the effect of some crystal growth inhibitors on the prevention of scale is evaluated in terms of amount precipitated gypsum, the particle size of the precipitated gypsum and the carbon gold loading capacity.INTRODUCTIONGold bearing sulfide ores are often roasted or pressure oxidised prior to leaching. The purpose of this unit operation is to prevent loading the leaching circuit with sulfides that consume cyanide. Pressure oxidation or roasting chemically converts the sulfides into sulfates and at the same time, the pH of the slurry ends up in the acidic range. Typically, lime addition is the preferred means to raise the pH to around 10 where gold leaching takes place. Combination of large amounts of calcium ions from the lime with sulfate ions from the ore induces precipitation of gypsum. Compounds like calcium carbonate may also precipitate if carbonate ions are present in the slurry. Depending upon the composition of the ore, compounds like calcium carbonate and other types of scale may also precipitate on gold surfaces on the slurry particles. A layer of scale on top of exposed gold surfaces will prevent dissolution in the cyanidation that takes place during leaching. Naturally, such a precipitation may lower the gold recovery."

Jan 1, 2016

By Luis Bergh, Juan Olivares, Juan Durán, Juan Yianatos

"In the last decades heuristic approaches based on logic rules have been one favored tool to control flotation units and plants on top of distributed control systems. Fundamental knowledge on flotation processes, expressed in reliable models, and programs to assure the quality of the information, contained in available measurements, are still insufficient to develop robust predictive control strategies. In this paper the idea of using simplified models, when a known disturbance is coming into the process, is explored. As a first approach, the set points of the froth depth and air flow rate controllers are estimated based on this model. Since these target predictions are only approximate, a conventional feedback expert system, based on logic rules, continues the task of calculating the set points of the distributed controllers, in order to decrease the gap between actual and desirable metallurgical targets. This combined actions permitted a fast response of the process to change the operation of the circuit when a measured disturbance is detected. This control system was implemented and experimentally evaluated in a pilot rougher flotation circuit, with three pneumatic cells, with froth depth and air flow rate controllers in each cell. Since the circuit is operated for the air-water system, a phenomenological model, with parameters estimated from industrial data, is fed on-line with real operating variables and virtual values, characterizing the feed (grades, solids%, particle size distribution), in order to predict the metallurgical targets (recovery and concentrate grade). Several cases are discussed showing the benefits of this control system and the possible improvements to work on. INTRODUCTIONToday, large size mechanical flotation cells of 100 to 300 m3 are used in rougher operation in different flotation industrial plants, in Chile and worldwide. However, in spite of the advances in fundamental research and the notable growing in equipment size, with more complete instrumentation systems, there are still a lack of reliable data for industrial flotation modeling and simulation to advance in better control systems design."

Jan 1, 2016

By W. Petruk, D. R. Morris

"The lead concentrate produced from the volcanogenic base metal ore of Brunswick Mining and Smelting in New Brunswick contains major to trace amounts of iron, zinc, cadmium, arsenic, antimony, copper, silver, selenium, tellurium, bismuth, sulphur, tin, indium, mercury and manganese as impurities. When the concentrate is sintered some of these impurities enter a variety of oxide phases, whereas others precipitate as metals. In the lead blast furnace the oxide phases decompose and the impurities recombine 10 form new phases, most are eventually discharged to the slag. The metals of the sinter remain as metals in the lead blast furnace where even more are produced, and are discharged largely with the lead bullion,IntroductionMany lead concentrates are produced from volcanogenic base metal ores . Such ores contain a wide variety of trace minerals and trace elements , therefore, concentrate s obtained from them will contain the trace elements as impurities . The impurities in the lead concentrate from one such ore, the Brunswick No. 12 deposit of Brunswick Mining and Smelting Corporation (BM S) in the Bathurst area in New Brunswick , were studied as pan of a larger investigation that was conducted to determine the extent of chemical reactions of the sinter within the lead blast furnace(1,2) The lead concentrate was investigated to identify the host mineral s for the impurities, the lead sinter was studied to identify the host phases, and frozen products from different depths within the BMS blast furnace at Belledune, New Brunswick were studied to determine the behaviour of the impurities.T he investigation was performed by pre pa ring polished sections o f the samples and studying them with a reflecting microscope, a scanning electron microscope (SE M) equipped with a Kevex energy dispersive X-ra y analysis system, a microprobe, and a Quantimet 720 image analyzer. The samples were also analyzed by X-ray diffractometer, and individual grains were analyzed by the Debye-Scherrer X-ray powder film method."

Jan 1, 1985