Search Documents

By Bruce Chalmers

INTRODUCTION TIE most important practical problem with which Physical Metallurgy is faced is the control of the mechanical properties of alloys. The most difficult aspect of this problem is the development of new alloys with the properties that are required for meeting exacting engineering requirements. A great measure of success has been achieved by following the empirical method and most, if not all, of the present variety of alloys have been developed by the process of experiment and observation or trial and error. It may, however, be that this method will become. less productive as time goes on, and that eventually it should be replaced by a process based on an understanding of the factors that determine the properties, so that alloys can be 'designed' to meet the requirements. This method of investigation will not be possible until a much better fundamental understanding of metals has been gained, and this will come only about as a result of a great deal of detailed research. The subject of Physical Metallurgy can be divided, as follows, into two parts: we may consider the factors which determine the structure, in the broadest sense, of an alloy. These include the composition and also the treatment to which the material has been subjected. The second aspect is the influence of the structure on the mechanical and other properties. In order to make an effective contribution in this field, it is necessary for an individual or a group to concentrate on a specific and very restricted topic. It is proposed to discuss in some detail the particular subject in which the writer and his colleagues are working.

Jan 1, 1951

By S. Amira

In the last two decades, many new creep-resistant magnesium alloys have been developed for high temperatures applications. Their mechanical performance and corrosion behaviour were reported for various experimental conditions. However, these conditions often led to uneven comparison basis. In the present study the microstructure, mechanical properties and corrosion performance of four of these newly developed creep-resistant magnesium alloys were systematically compared. Specimens were obtained from experimental box-like components that were die-cast and thixocast in comparable conditions. Their mechanical and corrosion properties were compared using similar testing conditions. Results show that the creep resistance, strength and impact resistance of specimens are comparable but systematically lower compared to specimens cast under optimized conditions. The reduced concentration of elements such as Al, Ca, Sr and Ce lead to a decrease of the corrosion resistance of the magnesium alloys in 3.5% NaCI solution.

Jan 1, 2007

By J. Etcheverry, E. Seguel, R. Díaz, F. Parada, R. Parra, E. Balladares

A thermodynamic and kinetic model is proposed to explain the formation of bornite, chalcopyrite and magnetite during partial roasting of enargite-containing copper concentrates. The proposed mechanism involves solid-solid-gas and solid-gas reactions between chalcocite, pyrrhotite, gaseous sulfur and oxygen. The formation of bornite could be explained by a two-step reaction: the first one involving the formation of chalcopyrite by a reaction between Cu2S, FeS and gaseous sulfur, followed by a second step in which the newly formed chalcopyrite reacts with additional chalcocite to form bornite. Although thermodynamically the direct formation of bornite is more favorable than that of chalcopyrite, the lower diffusion kinetics of bornite formation could explain the preferential formation of chalcopyrite. If the reaction occurs with stoichiometric chalcocite and pyrrhotite in the presence of gaseous sulfur to form chalcopyrite, no bornite is formed, while for the stoichiometric reaction between chalcopyrite and chalcocite in the absence of sulfur, only bornite is formed. For the formation of magnetite and chalcopyrite the mechanism could involve the partial reaction of chalcocite and pyrrhotite in the presence of oxygen. The proposed model is thermodynamically consistent with the experimental results obtained in laboratory and pilot plant. INTRODUCTION The processing of high-arsenic copper concentrates with over 0.7 wt.-% arsenic by conventional smelting-converting normally require an additional arsenic removal step to reduce arsenic content to levels below 0.2–0.3%. One of these high-arsenic copper concentrates is the one produced by the Ministro Hales Division (DMH) of CODELCO, which has the typical chemical composition shown in Table 1. Enargite (Cu3AsS4), chalcocite (Cu2S) and pyrite (FeS2) are the main mineralogical species present in these concentrates, with over 75 wt.-%, as shown in Table 2. Partial or “neutral” roasting of these concentrates under controlled temperature and partial oxygen pressure conditions at 923–993K (650–720ºC) can remove up to 95% of the arsenic as As2S3 (As4S6), which has a high vapor pressure under these conditions, leaving a calcine with low residual arsenic. In copper concentrates, arsenic is present generally as enargite and arsenopyrite. This compounds as well as others such as pyrite and covelite, decompose readily above 770 K (500ºC), releasing, in addition to gaseous arsenic trisulfide, gaseous sulfur which by oxidizing to SO2 generates most of the heat required by the process.

Jan 1, 2019

By W. Beres, R. E. Miller, B. Shiari, L. R. Zhao

A dynamic multiscale simulation method has been developed to study the material scratching processes on nanoscale single crystals. The model simultaneously captures the atomistic mechanisms near the free surface and the long range mobility of dislocations and their interactions, without the computational cost of full atomistic simulations. The method also permits the simulation of system sizes that are approaching experimentally accessible systems, albeit in 2D. Simulations are performed on single crystal aluminum to study the atomistic details, surface evolution, and generation and propagation of dislocations for a variety of scratching depths at room temperature. Simulations demonstrate the power of the developed method in capturing both long-range dislocation plasticity and short-range atomistic phenomena during tool advance. Variations of scratching normal and tangential forces are investigated and related to plastic deformation and dislocations generation during the simulation process.

Jan 1, 2006

By T. Abu Leil

A new class of ternary Mg-Sn-Ca alloys is being developed to address the dual demands of corrosion and creep resistance at service temperatures. While tin has proven to enhance the corrosion resistance, calcium is expected to significantly increase their creep resistance of binary magnesium alloys. Their effects in ternary magnesium alloys are not yet known. The series of alloys studied has Sn and Ca in the ranges 3-6% and 1¬2%, respectively. The results indicate that these alloys have two-phase structures with CaMgSn phase dispersed in a matrix that is predominantly a solid solution of magnesium. The corrosion behavior of these alloys has been investigated by means of salt spray tests and potentio-dynamic measurements. Creep behavior of these alloys was measured at a temperature of 135 C under an applied compressive stress of 85 MPa. Scanning Electron Microscopy with Energy Dispersive X-ray facility and X-ray Diffraction techniques were used to characterize the microstructures. The results indicate the prospect of designing alloys that can provide optimum combinations of corrosion and creep resistance by adjusting the relative compositions of Sn and Ca in the system.

Jan 1, 2006

By William H. Pomroy, Kenneth E. Hjelmstad

An underground mine fire can seriously threaten the lives of all personnel in the mine. This fact makes fire emergency planning a high priority in the mining industry. A fire emergency plan includes a means of warning miners of the existence of a fire, and the need to evacuate or retreat to a place of refuge. The warning alarm must be fast and must reach all miners, regardless of their location or work activity. Means of fire warning are varied, and include such methods as stench, flashing lights, telephones, and word-of-mouth (messengers). Unfortunately, none of these methods are entirely satisfactory. Stench can be slow and seldom achieves total mine coverage, especially in high-back room-and-pillar mines with low ventilation velocity. Telephones are effective only where personnel are close enough to hear the phone ring. A novel fire warning alarm system has been developed by the U.S. Bureau of Mines which enables instantaneous warning of all underground personnel. The warning alarm is sent by an electromagnetic signal which penetrates through mine rock from a transmitter to small person-wearable receivers. Each miner's cap lamp battery could be equipped with a small receiver and when a fire or other emergency occurs the miner could be alerted to the danger by a blinking of the cap lamp. Testing of prototype equipment has demonstrated that the transmitted signal is capable of penetrating through over a mile of mine rock and activating the receiver. This paper describes the theoretical basis for through-the-rock ultra-low frequency electromagnetic transmission, design of the prototype transmitter and receiver, test results, and status of commercial development of systems utilizing this technology.

Jan 1, 1994

By J. Drenda

The model for methane removal from the workings directly behind an advancing longwall as presented in this paper may be used for U-ventilated cross or length-wise systems of longwall advance, starting from the boundaries of the extraction field. In mines with high methane concentrations, Uventilated longwall extraction from the boundary of the extraction field produces a methane risk. The risk is manifested by a higher methane concentration at the end of the longwall, upper gate and incline. The methane in increasing concentrations, which is emitted mainly from the workings with caved areas, appears towards the end of the longwall and in the upper gate. The graphical model of the longwall provided includes both the workspace of the longwall and the caved area. Based upon a model of the rock distribution in the cave, a ventilation model comprising two standard air splits and large number of crosswise air splits has been constructed. Simulations indicate that if the shearer is not present in the longwall, the air distribution in the caved area is symmetrical. The presence of the shearer, both at the bottom and the top of the longwall, causes an asymmetrical air distribution in the cave, that is the asymmetrical flows in the goaf and longwall workspace and in the inflows and outflow between those regions. This phenomenon causes an increase in methane concentration at the end of the wall and at the upper gate. The methane removal method proposed for workings with a caved area directly behind the advancing U-ventilated longwall, starting from the boundary of the field, consists of the removal of methane-air mixtures from the caved area with the boom pipes. These booms may be of several meters long and may be extended if necessary. The insertion of the boom pipes into the cave towards the end of the longwall and connecting them with the general methane removal system creates negative pressure causing a change in the depression field, which is the aerodynamic potential field in the goaf area around the ends of the boom pipes. This will promote the extraction of the methane-air mixture from voids and the goaf cracks, and the area from which methane is being extracted may extend to the side of the cave. This is a positive phenomenon, which could result in the methane flow from the goaf into the airflow in the longwall workspace decreasing or even stopping. A reduction in the methane flow into the longwall workspace with extractions booms will be advantageous for the production continuity. Based on the floor load model for the rocks in the cave and the methane-removal boom load model, the value of the force required to move the boom behind the advancing wall has been calculated. Strength calculations for the pipe were performed using a finite elements method. The analysis results, as well as the comparison of the pipe material effort to the strength parameters of steel, which can serve as piping material (for the assumed load conditions), lead to a belief that the proposed boom construction satisfies the strength requirements.

Aug 1, 2013

By C. -S. Xie, J. -H. Kong

The microstructure and mechanical properties of X80 hot-rolled thick steel strips with a thickness of 17.5mm produced in Wuhan Iron & Steel Company (WISCO) are introduced in the paper. The steel strips as fabricated through proper thermomechanical processing (TMP)/ on-line accelerated cooling (OLAC) processing have shown high strength and toughness, low brittle transition temperature, good weldability, and high Shear Area (SA) percentage in Drop Weight Tear Test (DWTT). The microstructure of the steel strips is characterized with mainly acicular ferrite, and fine dispersed Martensitc-Austenite (M-A) phases. It is determined that the mechanical properties are improved due to the presence of the fine M-A phases and precipitates, which could be formed by reducing the finish rolling and coiling temperatures.

Jan 1, 2005

By Esa Peuraniemi, Hanna-Leena Heikkilä

Boliden Harjavalta has been operating a copper flash smelter since 1949. Thus, in 2019, the smelter is celebrating its 70th anniversary of flash smelting. Slag formation is an integral part of the smelting process; currently the processing of slag is based on froth flotation at the slag concentrator. It provides high recovery of copper but restricts slag utilization; the final copper slag is deposited in a landfill. The Harjavalta smelter commissioned a new landfill area for final slag in May 2018. This paper describes the full project from permitting to commissioning of a new landfill area. The permitting process is described comprehensively, including environmental impact assessment together with the environmental and dam safety monitoring. During the environmental impact assessment, observations on rare animals protected on European level were made as well as archaeological findings. Successful completion of the permitting allowed the construction phase to start on time. After six years of intensive work, the new landfill was commissioned in May 2018. The new landfill area provides a sustainable way to store the smelter’s slag for decades to come. INTRODUCTION Slag processing Sulphide based concentrates have always formed the main raw material stream at Harjavalta’s copper smelter. During the smelting and converting steps, the iron included in the concentrate is oxidized and fluxed using a silica-based sand. Originally, the slag was processed by using an electric slag cleaning furnace after which the final slag was water granulated. Froth flotation has been utilized for slag treatment since 1966. In the beginning, the slag was cooled in open ditches. In 1984, controlled slow cooling of slag was licenced to enhance copper recovery at the flotation plant. Today, the slag from both the smelting and converting is tapped/skimmed to slag ladles and treated in the following steps: Slag ladle transportation from the smelter to the cooling area by slag hauler Slow cooling of slag in the ladle to allow mineral precipitation Unloading the slag by tilting the ladle; causing the slag to crush as it drops from the ladle Feeding the crushed slag (-500 mm) by wheel loader to a slag concentrator’s feed funnel followed by a conveyor belt transporting the slag to the concentrator plant Crushing and grinding using lump and pebble mills Froth flotation of the valuables Recycling the slag concentrate back to the smelter feed after dewatering Pumping the final copper slag to the landfill area.

Jan 1, 2019

By L. K. Mireku

"Abstract - The Halfmile Lake South Deep zone, Bathurst Mining Camp, New Brunswick, was discovered by Noranda Inc. (Exploration) as a result of a 3-D seismic survey in 1998 and the subsequent drilling of ten diamond-drill cores. The deposit consists of massive, breccia, and stockwork Pb-Zn-Cu sulfide minerals, and is hosted by a volcano-sedimentary sequence belonging to the overturned Ordovician Tetagouche Group. Epiclastic rocks and interbedded fine-grained felsic pyroclastic rocks dominate the stratigraphic footwall. Locally, crystal-rich felsic tuffs and subordinate epiclastic rocks comprise the immediate stratigraphic hanging wall. The entire stratigraphic sequence was intruded by quartz-feldspar porphyritic intrusions, and cut by intermediate and basic dikes. The volcanic and sedimentary rocks can be discriminated geochemically using trace element ratios such as Zr/TiO2 and Nb/TiO2, despite intensive alteration and cleavage development. These ratios indicate that four protolith volcanic compositions exist: rhyolite, dacite, andesite, and basalt. The aphyric and feldspar- and quartz-phyric volcanic rocks are dacitic and rhyolitic in composition; epiclastic rocks have trace element ratios consistent with dacitic compositions. Pearce element ratio diagrams, general element ratio diagrams, and petrographic observations demonstrate that the rhyolitic volcanic rocks exhibit evidence of albite, potassium feldspar, and quartz fractionation, dacitic volcanic rocks exhibit little evidence of any fractionation, and epiclastic sedimentary rocks exhibit evidence of quartz sorting only. Hydrothermal alteration is best represented by the presence of phengitic muscovite and daphnitic chlorite. Minor calcite occurs in the stratigraphic hanging wall, deep in the stratigraphic footwall, and in post-mineralization dikes, and thus is not interpreted to be part of the causative hydrothermal event. Element additions and losses during alteration have been used to determine net alteration reactions, and these have been used to identify alteration parameters that are independent of other forms of alteration and fractionation/sorting, and which can be used to guide exploration. These parameters include: a bulk hydrolysis measure, (2Ca+Na+K-2CO2)/Al; a muscovite alteration measure, K/Al; an albite destruction measure, Na/Al; a chlorite alteration measure, (Fe+Mg-S/2)/Al; a chlorite composition measure, (Fe-S/2)/Mg; a sulfidization measure, S/Ti; and a carbonatization measure, CO2/Ti. With the exception of the carbonatization measure, these alteration parameters define a distinct lateral and vertical zone of intense hydrothermal alteration in the stratigraphic footwall of the deposit, and demonstrate that the epiclastic rocks are predominantly chlorite altered, and the volcanic rocks are predominantly muscovite altered. Within the alteration halo, element additions of Fe and H, and element losses of Na are characteristic. Potassium was added to muscovite-altered rocks, but subsequently removed from chlorite-altered rocks. The results from this study demonstrate that metamorphism and deformation have not significantly obscured hydrothermal alteration signatures."

Jan 1, 2006

By Michael S. Moats, Addin Pranowo, Gerardo R. F. Alvear F., Nigel Aslin

The toxicity of arsenic is well known and documented. However, the presence of arsenic in copper electrorefining anodes and electrolyte is critically necessary to produce high quality cathode. Arsenic as well as antimony and bismuth concentrations vary depending on their relative concentration in the anode copper received from the smelter. This paper will discuss the behaviour and benefits of arsenic in copper electrorefining and the detrimental effects of antimony and bismuth on cathode quality and tankhouse performance. This will include the minimization and mitigation of problems associated with arsenic, antimony and bismuth including cathode contamination, floating slimes, scaling and anode passivation.

Jan 1, 2014

By Simon Pelletier, Jose Delgadillo, Dave Page, Pramod Kumar, Raj Rajamani, Dilek Alkac, Martin Fillion

"In general, many past works examine mill load, mill power, shell lifter design etc with a view to improving the mill capacity. On the contrary, only a handful of papers have addressed the transport of fine slurry through the pulp lifters. We present the flow dynamics of pulp lifters via laboratory scale experiments, high speed photography and modeling with computational fluid dynamics. Next, the flow behaviour in ArcelorMittal’s Mont-Wright autogenous mill discharge flow is examined. In an effort to improve mill throughput, a comprehensive simulation and plant scale study of the mill was taken up with a focus on the shell and pulp lifter design. The shell lifter was found to be at its optimum limit for breakage of ore particles given the constraints of wear life and occupied volume. Next, the pulp lifter study was taken up with computational fluid flow code and discrete element code. The simulations directly showed that there was considerable carry-over of slurry. This effect was traced to the area restriction in the pulp lifter channels. Further, crash-stop studies confirmed slurry pooling within the mill. Thus it was readily apparent that mill throughput can be increased if the pulp-lifter could be redesigned. Consequently, the discharger section of the pulp-lifter was redesigned.First, this paper outlines the modeling in laboratory scale studies and plant scale studies leading up to the discharger design. Next, the discharge flow in seven different published mill surveys is predicted with computational fluid dynamics (CFD) methodology shown here. Finally, Mont-Wright mill circuit performance before and after the discharger redesign is described. The usefulness of fluid flow simulations in the design of pulp-lifters is emphasized."

Jan 1, 2012

By N. Katsikaros, R. Agius, B. Adaszynski

"With stricter limits globally being imposed on cyanide discharge levels in plant tailings, having a reliable and well designed cyanide detoxification circuit is critical for any operation. The INCO SO2/Air method is most commonly used for cyanide detoxification where sulfur dioxide and oxygen combine to oxidize cyanide to the much less toxic cyanate. This paper discusses the steps involved with the development, from laboratory through to design, of a robust cyanide detoxification circuit. The goal is to produce a cyanide detox circuit that reliably meets discharge target with the lowest operating and capital cost.Design begins in the laboratory where continuous tests simulate full scale operation of a detoxification circuit. Detailed design relies on several design parameters, based on theory and experience, to ensure the reactor can satisfy requirements of the cyanide destruction reaction. Selection of the correct reagents and their supply to the reactor is important to an operable process with minimal operator workload. The operability of the system relies on correct process control strategies to maintain optimal reagent addition and chemical conditions in the reactor. These design factors are critical to providing a robust plant that will consistently meet cyanide discharge levels, ensuring uninterrupted production and plant profitability."

Jan 1, 2014

By L. Tang

A seismic monitoring system was installed in 2005 at Dongguashan Copper Mine, the deepest metal mine in China. Based on the seismic events monitored in situ, the possibility of rockburst prediction and prevention is investigated in this paper. The characteristics of space-timeintensity of mining-induced seismicity and the seismic response to mining are studied in detail using the seismic data in Dongguashan Mine. A conceptual model and a criterion of assessment of hazard seismic nucleation are proposed for Dongguashan Mine. In this model, the mine seismic stiffness method is adopted for rockburst prediction within the framework of the unstable failure theory. To analyze rock failure cases in Donggauashan Mine, the rate of the ratio of stiffness of rock in nucleation area to its surrounding area is proposed as a criterion for rockburst prediction.

May 1, 2009

By W. L. Brown

"The properties of Base Metal Mining Corporation are in Yoho Park about 2 1/2 miles northeast of Field; British Columbia; on the main line of the Canadian Pacific railway. There are actually two mines; the Monarch on mount Stephen and the Kicking Horse on mount Field; separated by the steep valley of Kicking Horse river. The outcrops of the orebodies range from 4; 900 feet to 5; 300 feet above sea-level. The concentrator is situated below the Monarch mine and is connected to the main portal by an aerial tramway. The ore from the Kicking Horse mine is conveyed by aerial tramway to a storage bin on the main highway and is then trucked to the concentrator.During the construction of the Canadian Pacific railway through Kicking Horse valley, galena float was found at the base of mount Stephen. The East Monarch outcrop was staked in 1894. The outcrop of the West Monarch ore body on the cliff face of mount Stephen was not discovered until 1916. The Kicking Horse orebodies on mount Field were discovered a few years later. In 1912, a 75-ton concentrator was erected, which operated at intervals until 1924. During this period approximately 42,000 tons were mined and milled, largely from the East Monarch orebody. In 1928, the Base Metal Mining Corporation, Limited, was formed to take over the Monarch and Kicking Horse mines. A 300-ton differential flotation concentrator was erected and production started in the autumn of 1929. In a very short time, however, the low price of metals forced the mill to shut down until August 1933. From 1929 to 1935, when the mill again ceased operation, a total of 256,500 dry tons of ore, averaging 1.59 oz. silver per ton, 9.7 per cent lead, and 12.6 per cent zinc, was mined and milled, largely from the West Monarch orebody. After a period of further underground development, the concentrator reopened in 1940 and is still in operation. From 1940 to the end of 1944, 354,363 tons of ore was milled, averaging 5.32 per cent lead and 10.47 per cent zinc."

Jan 1, 1954

By D. G. Macintyre

Thick westward prograding clastic wedges were deposited along the margin of ancestral North America from Mid-Proterozoic to Mid-Paleozoic time. Periodic rifting and tectonic subsidence resulted in the formation of starved sub-basins along this otherwise passive continental margin. These sub-basins host important sedimentary exhalative barite-zinc-lead-silver deposits. In northeastern British Columbia, a thick succession of Paleozoic basinal facies clastic rocks is preserved within the northwest-trending Kechika Trough. Within the trough, sedimentary exhalative barite and barite-sulfide deposits occur in starved basin sediments of Middle Ordovician, Early Silurian, and Late Devonian age. The last are the most economically sigrrificant and are hosted by carbonaceous cherty argillites and siliceous shales of the Middle to Late Devonian Gunsteel Formation of the Lower Earn Group. The largest deposit, Cirque, has reserves in excess of 35 million tonnes averaging 100J0 (Pb +Zn) and 47 g/t Ag. Other potentially significant deposits include Driftpile Creek, Bear, Mt. Alcock, Fluke, Pie and Elf. Stratiform barite deposits are also common, particularly near the basin-to-shelf transition zone. The Late Devonian barite-sulfide deposits typically are zoned: interlarninated barite-sphalerite-galena-pyrite occurring near suspected vent areas grades outward into bedded barite. Laminated beds of pyrite typically occur in hangingwall siliceous shales, particularly above the inferred vent zone. The apparent absence of epigenetic stringer sulfide zones and footwall alteration implies that the deposits were formed from ponded brines at relatively low temperature. Away from the main deposits, the favourable stratigraphic interval is marked by the presence of thin beds of nodular and laminated barite and thin laminae of pyrite. Thin tuff beds also occur locally in this stratigraphic interval and are evidence for a Late Devonian volcanic event. A paleogeographic reconstruction of the Kechika Trough in Late Devonian to Mississippian time suggests that the barite-sulfide deposits formed in third-order starved basins between uplifted, northwest-trending horst blocks that were capped by shallow-water carbonate banks. The presence of intraformational breccias suggests that fault movement accompanied barite-sulfide precipitation. This tectonic activity may have allowed the escape of heated, overpressured metalliferous brines from permeable reservoirs within the sedimentary pile. Sedimentary exhalative deposits formed where these brines were exhaled as buoyant plumes onto the seafloor, cooled, and ponded in anoxic seafloor depressions.

Jan 1, 1992

By B. Garitte, O. K. Mahabadi, P. Marschall, A. Lisjak, H. R. Müller, T. Vietor, G. Grasselli

Numerous research studies have shown that clay rock formations exhibit favourable characteristics for the deep geological disposal of radioactive waste. However, one main concern is that the favourable long-term isolation properties of the intact rock mass could be negatively affected by the formation of an excavation damaged zone (EDZ) around the underground openings. The goal of this paper is to present new rock mechanics insights into the phenomena involved in the EDZ formation and evolution processes in Opalinus Clay, a clay shale currently being assessed as a potential host rock for an underground repository in Northern Switzerland. More specifically, discontinuum-based computer simulations, using a hybrid finite-discrete element method (FDEM) approach, were applied to two case studies considering circular excavations in an anisotropic Opalinus Clay formation. In the first case study, numerical modelling was applied to the HG-A experiment, a long-term in-situ test carried out at the Mont Terri underground rock laboratory to investigate the hydro-mechanical response of a backfilled and sealed microtunnel. A mechanistic analysis of the fracturing processes involved in the EDZ formation was carried out. In the second case study, the long-term effect of the bentonite backfill swelling on the EDZ around an emplacement was numerically analyzed. Overall, the simulation results highlight short-term distinctive rock failure kinematics due to the bedded rock structure, as well as a long-term reduction of the excavation-induced fracture porosity in response to mechanical loading.

Jan 1, 2015

By R. G. L. McCready, Marco Zentilli

"Brogan coal containing mean averages of 6,93% w/w total sulphur (1.1% sulphate sulphur, 1.6% organic sulphur and 4.24% pyritic sulphur) and 16.34% mineral ash was used as the test coal in these studies.Shake-culture leaching studies on seven size fractions of the coal, ranging in size from 0.045 mm to 1.7 mm, showed that the rate of pyrite leaching was inversely proportional to the particle size. As the use of continuous stirred tank reactors would be uneconomical for the reclamation of waste coal, column leaching studies were initiated on coal sieved to >6.35 mm to < 12.7 mm, The leachate was monitored for all metal ions and the release of iron was used to monitor the rate of pyrite oxidation . Measurable amounts of Zn, Co, Ni, Mn, and V, all of which can replace iron in the pyrite crystal structure, were released during the initial stages of leaching. Further, high concentrations of AI, Ca and Sr and trace amounts of Sn, As. Se, B, Ca, Cr, Si, and Ti were detected in the column effluents.These studies suggest that bacterial leaching will remove the pyrite and qualitative amounts of environmentally undesirable trace metals from the coal if such a process is developed for waste coal reclamation.IntroductionIn 1947, Colmer and Hinkle showed that acid mine drainage was the result of an oxidative attack of the iron-mineral sulphides by Thiobacillus ferrooxidans to produce sulphuric acid . Ashmead (1955) proposed the use of these organisms to desulphurize coal , but the subsequent research effort was concentrated on the metabolism and physiology of these extreme acidophiles.A limited number of studies have been reported on the bacterial leaching of pyrite from coal (Silverman et al., 1963; Dugan, 1977). However, the bacterial oxidation of pyrite is a self-limiting first-order reaction, probably due to the precipitation of Fe(OH)J and elemental sulphur , which progressively inhibits intimate contact between the bacterial cells and the sulphide-mineral surface. Consequently, the best pyrite oxidation experiments with coal reported to date required five days to remove 97070 of the pyrite (Dugan &Apel , 1978) using mixed cultures of T. ferrooxidans and T. thiooxidans."

Jan 1, 1985

By Ö Yilmaz

In this study, the behaviour of rock mass subjected to blasting load is investigated using three dimensional finite difference numerical modelling. In the analyses, Mohr-Coulomb failure criterion has been used for the characterisation of the rock mass strength. Stresses acting on the borehole boundary have been simulated by an exponential function which reaches its maximum within a short time and then falls to zero value in a considerable time period. The strain rate effect on the mechanical properties of rock material has also been taken into account in the analyses. Four different explosive-rock mass combinations have been studied to investigate blast induced damage zone. It has been observed that proposed equation for the dynamic compressive strength of rock material fits very well to general suggestions. Results have shown that blast damage analysis model recommended with this study is successful.

Aug 1, 2013

By D. R. Hatton

To obtain sufficient material on which to perform copper-molybdenum separation testwork a variability set of drill hole reject samples amounting to several tons was put together to include the different ore types proportions expected in the copper circuit. The samples were treated in a copper circuit pilot plant and enough mass of bulk concentrate was recovered to conduct copper moly separation tests in the laboratory. Tests consisted of stage flotation reactor (SFR) rougher pilot plant tests, conventional laboratory rougher, cleaner and 4 stage open circuit cleaner tests. The mineralogical liberation analysis of the feed and concentrate was used to model the effect of liberation on the grade-recovery relationship of the different samples. Mineral kinetic parameters for the various samples were determined by calibration to the test data. The copper concentrate results as simulated from previous studies on the same deposit were used to simulate the variability in head grade and throughput expected for the feed to the copper molybdenum separation circuit for each of the first 10 years of production. This variation in feed was then simulated through the separation circuit to obtain optimised molybdenum grade recovery curves to forecast the circuit production for each of the first 10 years. INTRODUCTION Incorporating Geometallurgy into the design for a copper molybdenum separation is especially challenging due to the low mass of final concentrate typically produced during testwork. This is due to the low molybdenum head grades and high overall molybdenum upgrading expected. With molybdenum head grades of around 300 ppm, 1 tonne of copper circuit feed is expected to produce around 300 g of molybdenum concentrate in the plant. In the laboratory however, this may end up only resulting in a few grams. Obtaining sufficient mass for laboratory testing therefore requires starting with a large initial sample and careful testwork planning to maximise the utilisation of this mass. A testwork program was designed to investigate the effect of ore variability on the copper molybdenum separation circuit (here after referred to as the molybdenum circuit). Composite samples were selected to represent the various ore types, copper content, moly content, pyrite content and clay contents expected in the copper circuit feed. These samples were run through a bulk copper pilot plant to create the feed for the molybdenum testwork. The molybdenum testwork consisted of rougher kinetic flotation tests, rougher cleaner kinetic tests, rougher cleaner kinetic tests with regrind, stage flotation reactor (SFR) pilot plant tests, open circuit cleaner tests. These tests were used to calibrate the ore kinetics in the IGS-FLEET model for simulation of the molybdenum circuit performance.

Jan 1, 2019