Search Documents

By T. R. Yu, D. B. Counter

"In an effort to increase productivity, the use of fly ash as a binder for consolidated backfill was studied. From laboratory and underground tests f or its cementitious properties and environmental effects, it was found that a portion of Portland cement could be replaced by the same amount of type ""C"" fly ash to produce an acceptable consolidated rockfill product for use at Kidd Creek.The environmental concerns in terms of dust control and emanation of radon gas were unfounded from measurements. The dust count was comparable to the use of Portland cement only, or with ground blast furnace slag, and the radiation readings were low, averaging one-seventh the regulation level.Since May 1984, a total of over 100 000tonnes of fly ash has been consumed as a binder blended with Portland cement, producing over four million tonnes of consolidated rockfill. To date, the fill in the stopes has performed very satisfactorily, while yielding considerable cost savings.IntroductionThe Kidd Creek minesite, located 27 km north of the city centre of Timmins, Ontario, produces 4.5 million tonnes of base metal sulphide ore annually. The mining method for both No. I and No .2 mines is mainly sub-level blasthole stoping with delayed backfilling.No. 1 mine was developed with a shaft to a depth of 930 m in 1973 to recover the ore between the floor of the open pit at the 216 m horizon, and the 792 m horizon. Stopes are normally 18 m wide, 22 m to 65 m long, with heights varying from 90 m to 135 m. Vertical rib pillars between stopes are typically 24 m wide and sill pillars are 30 m thick.Pillar recovery is implemented after the consolidated rockfill placed in the mined stopes has cured for a period of at least three months. This allows a maximum recovery of the ore with a minimum of dilution, while also maintaining safe working conditions.No. 2 mine was developed from a second shaft, sunk to a depth of 1530 m in 1978, for the recovery of ore beneath the No. I mine. Sub-level stoping in No .2 mine is similar to No.1 mine in methodology, yet differs in sequencing, as no rib pillars are left."

Jan 1, 1988

By K. Yoo

Chalcopyrite is the most abundant copper sulfide mineral, which is normally processed using pyrometallurgical methods (i.e., smelting) to produce copper metal. Smelting has several major disadvantages, such as high gas-handling costs, high capital costs, saturation of sulfuric acid market, and inability to treat low-grade concentrates and to recover some by-products, such as zinc, nickel and cobalt. The development of hydrometallurgical processes for chalcopyrite is desirable to overcome the problems of smelting. Because chalcopyrite is refractory, the leaching rate for chalcopyrite is very low. Therefore, increasing the leaching rate has been extensively investigated, both in sulfate and chloride media, as well as in the presence of bacteria. Chloride leaching processes have shown relatively high leaching rates. The mechanism of the chloride leaching process has been investigated, but the behavior of chalcopyrite leaching in chloride solution is not clear. Therefore, the effect of the solution redox potential on the leaching rate of chalcopyrite in chloride solution was investigated. In the present study, leaching experiments were carried out using 0.1 M chloride solutions and the results indicate that high leaching rates of chalcopyrite can be achieved at relatively low solution redox potentials.

Jan 1, 2007

By Trent Hamilton

Cameco ? McArthur River Operation is a high-grade uranium mine in northern Saskatchewan. Average grades mined are nearly 20%, more than 20 times higher than other operating uranium mines in the world. The significant risks involved with mining this grade has been effectively mitigated using innovative and unique controls, implemented from development and production mining through to ore processing. The types and sources of radiation are presented and protection measures are discussed. McArthur River?s strong radiation culture is evidenced by continually low radiation exposures while transitioning to new mining zones.

Aug 1, 2010

By Avinash Kandalam, Markus Reuter, Jörg Kleeberg, Michael Stelter

The Top Submerged Lance (TSL) technology has obtained significant importance in the pyrometallurgy industry for nearly four decades. One of the advantages of TSL furnace is its high reaction rate, which is caused by splashing and turbulence of the melt. In contradiction, this phenomenon stands as a barrier for conducting experimental investigations to validate the simulation models. The highly turbulent and splashing environment in the TSL furnace is caused due to the immersion of the lance into the slag layer and thus the effect of the flame structure is directly related to the splashing, turbulence, reaction kinetics and life-span of the lance. Moreover, the material properties such as viscosity, density and the surface tension will also influence the flame structure. As a first step to understand the flame structure, attempts are made to generate a stable flame of the lance in an open environment. INTRODUCTION Top Submerged Lance (TSL) technology was invented during the 1970s at Commonwealth Scientific and Industrial Research Organisation (CSIRO), Australia by Floyd and Denholm. This technology was later commercialised and currently, there are about 100 TSL plants around the world commissioned by various licence holders such as AUSMELT (Outotec) and ISASMELT (Xstrata- Glencore Technology). Copper is the most produced non-ferrous metal followed by lead and zinc, see Hunt (2005). Today, a wide range of primary, secondary, and complex recycling materials are used as a feed material in the TSL, Alvear et al. (2010), Kaye et al. (2008). The working principle of TSL technology lies on inserting and submerging a lance from the top of a vertical cylindrical chamber into the slag layer. The lance is considered as the heart of the furnace, where the air and fuel are transported through two concentric tubes and are mixed in a combustion chamber, which is approximately 7 cm from the tip of the lance (considering the pilot-scale TSL furnace at the Institute for Nonferrous Metallurgy and Purest Materials - INEMET). The TSL furnace is very flexible with the type of fuel, feed material and the air input. The fuel can be natural gas/heating oil/fine coal particles and the air could be enriched with oxygen (Figure 1). The general mechanism of the TSL furnace lies on feeding the material from the top of the furnace and the material is pulled into the molten bath due to the high turbulent atmosphere, which results in high reaction rates. The thermocouples installed in the furnace (i.e. in the ceramic linings) allow the operator to know the temperature of the melt. For example, in the case of copper production the tapped material (i.e. matte/metal) can be transported to a settler for further processing or directly used.

Jan 1, 2019

By K. E. Haque

"This paper is a brief overview of the role of oxygen in cyanide leaching of gold feeds (e.g. ore, concentrate). As the majority of gold occurs in the elemental state (Au °), its oxidation is of vital importance for dissolution in the cyanide lixiviant. The cyanidetion at high pH is favourable for the oxidation of Au° with a mild oxidant such as air or oxygen. Beside oxidation of gold, deleterious effects of soluble sulphides, arsenates, antimonates on cyanidation of gold can be alleviated by preaerating the leach slurry with air or oxygen (i.e. preaeration process).If gold is refractory due to its occlusion in sulphides, silicates, tellurides, etc. then gold liberation is possible by roasting in the presence of oxygen or by leaching under oxygen pressure. The data in the recent literature indicate that reactive oxygen supplied by H202, Na202, Ca02 or 03 during cyanidation can accelerate considerably gold oxidation-cyanidation and yield high gold recovery in much shorter leach time. The information compiled in this review leads to the conclusion that oxygen plays a vital role in the dissolution of gold in cyanide lixiviant."

Jan 1, 1992

By A. -I. Abenhaim, I. Sasu, C. Perron, I. Mantegh, S. Larose

Manufacturing long shafts, such as those used in turbine engines, normally involves with drilling inside them in order to take the excessive mass out. Concentricity between the shaft axis and that of the drilled hole is very crucial as it impacts the mass distribution around the axis of rotation. It is important that the shaft mass be well balanced around the central axis in order to minimise the centrifugal forces on the bearings and supporting structure as well as any unwanted vibrations. The eccentricity problem, mostly in long shafts, comes due to machining limitations. It is difficult in long shafts to maintain the concentricity tolerances while drilling inside the shaft. In this work, we address the problem of correcting this eccentricity problem, i.e., when the axis of the inside hole deviates from the central axis. The presented work is based on a threepoint bending method and investigates its effect on the residual stresses and plasticity regions induced on the shaft. A full finite element model is presented that can used to design the solution parameters (bending load, location, etc.) and predict the effect. Limited experimental results are also presented to validate the finite element modelling.

Jan 1, 2006

By J. W. Senn

A magnesium alloy modeled after commercial alloy WE54 was thermomechanically processed and characterized to understand the mechanisms by which its texture can be randomized, as reported by Ball and Prangnell [1]. Samples were deformed in plane strain compression to prescribed strain levels at temperatures high enough to prevent cracking and then recrystallized. The deformation texture is very similar to that observed after plane strain compression (e.g., rolling) of other Mg alloys, such as common AZ31. However, the texture can radically evolve during recrystallization. Annealing above the precipitate solvus temperature results in a nearly random recrystallization texture where the initially strong basal texture is completely eliminated. Annealing below the solvus temperature produces a recrystallized texture similar to conventional Mg alloys, i.e., a weakened basal texture. If this same material is then annealed above the solvus to promote grain growth, a randomized texture evolves, which is similar that of samples simply recrystallized above the solvus. It is hypothesized that a sort of preferred growth mechanism, whereby grains with random orientation grow faster than those with the original basal texture, contributes significantly to the texture randomization observed in wrought magnesium alloys containing rare earth elements.

Jan 1, 2006

By H. T. John

"The objective of this paper is to demonstrate how the optimum cut -off grade can be calculated for typical large tonnage openpit mines. In the examples, it is assumed that the concentrator tonnage is fixed and that there are no market restrictions. The mining rate is assumed to be variable. This is usually the situation at an operating property.ModellingA model of the ore body is required to examine alternate cutoff grade strategies. The model must be accurate in its relationship between grade and tonnage. Table I shows a typical relationship between ore tons and grade for various cut-off grades. The average strip ratio is also shown. For higher cutoff grades, the ore tonnage is decreased and the ore grade is increased. Strip ratio increases with the cut-off grade.Using the relationship between ton s and grade, and assuming a homogenous, long life orebody, a simple calculation of the optimum cut-o ff grade can be made. The objective is to maximize the present value of cash flows. For the long life homogenous orebody example this objective is satisfied by maximizing present cash flows.Cash flow is calculated by subtracting operating cost from revenue . Operating cost will increase with the cut -off grade as the strip ratio increases."

Jan 1, 1985

By Jeremy Breker

Cameco aligns its social and environmental responsibilities with its vision, mission and values. Environmental Leadership is established as a corporate objective that emphasizes the triple-bottom-line and a systematic approach to understanding environmental, social and economic issues, risks and opportunities. These are ingrained in the project culture, systems and processes and used to influence solutions derived by the project teams to achieve Cameco's objectives. This paper traces the organizational objectives from the early stages of a project through to implementation and turn over to Operations. A case study is used to demonstrate how an asset is influenced by Cameco?s strategy.

Aug 1, 2010

By J. L. Luo, D. G. Ivey, A. H. Adeleke

Double-edge-notched flat tensile samples of X70 steel were used for both slow strain-rate testing (SSRT) and cyclic loading testing with the notch located in the zone of interest, i.e., the weld metal (WM), base metal (BM) and heat affected zone (HAZ). By using both optical and scanning electron microscopy, the stress corrosion cracking (SCC) behaviour with respect to crack morphology and various forms of microstructure was investigated. In all the samples considered, the mode of failure was predominantly transgranular with cleavage facets around the edges of the fracture surface. The BM, with a bainitic microstructure, had the highest resistance to SCC when compared with the mixed microstructures of acicular ferrite-primary ferrite and acicular ferrite-grain boundary ferrite observed in the WM and HAZ, respectively. The effect of microstructure on stress corrosion cracking behaviour is discussed based on experimental observations.

Jan 1, 2005

By M. L. Wacker

"Cigar Lake high-grade uranium mine in Saskatchewan is operating after 25 years of test mining, construction, and mine flood remediation. Factors include ground stability, groundwater control, radiation exposure, and ore handling. A 10 year test program resulted in validating “jet boring”, a non-entry mining method involving artificially freezing the orebody and surrounding rock; tunnelling to develop access crosscuts below the orebody; installing cased pilot holes through ore; extracting ore using rotating high-pressure water jets within pilot holes; and cavity concrete backfilling. Ore slurry is prepared underground, pumped to surface, and trucked to McClean Lake mill for processing to uranium concentrate.RÉSUMÉ Après 25 années d’essais sur les méthodes minières, de construction et d’assainissement suivant les inondations à la mine, l’exploitation de minerai à haute teneur en uranium Cigar Lake, localisée dans la province de la Saskatchewan, est opérationnelle. Les principales difficultés concernent la stabilité du terrain, le contrôle des eaux souterraines, l’exposition aux rayonnements et la manutention du minerai. Un programme d’essai de 10 ans a abouti à la validation du « forage à érosion », une méthode minière qui consiste à congeler artificiellement le corps minéralisé et les roches environnantes ; à creuser des tunnels pour développer des travers-bancs d’accès en dessous du corps minéralisé ; à installer des puits de fondation pilotes à travers le minerai ; à extraire le minerai à l’aide de jets d’eau à haute pression dans les puits pilotes ; et à remblayer les cavités avec du béton. La boue de minerai est préparée sous terre, pompée vers la surface puis transportée par camion jusqu’à l’usine de concentration de McClean Lake pour le traitement afin d’obtenir du concentré d’uranium.INTRODUCTIONThe Cigar Lake deposit is in northern Saskatchewan, 660 km north of Saskatoon, Saskatchewan, Canada, at the east edge of the Athabasca basin (Figure 1; Bishop, Mainville, & Yesnik, 2016). The operation is jointly owned by Cameco Corporation, AREVA Resources Canada Inc., Idemitsu Canada Resources Ltd., and TEPCO Resources Inc. Cameco has been the operator of Cigar Lake since January 2002. The discovery hole was drilled in 1981. Commercial production was declared in May 2015 and the Phase 1 operation will have a mine life of 15 years."

Jan 1, 2017

"The United Nations, through the secretariat of the United Nations Economic Commission for Europe (UNECE) and its Ad Hoc Group of Experts on Harmonization of Fossil Energy and Mineral Resources Terminology, developed the Framework Classification.The UN Classification applies to fossil energy and mineral reserves and resources located on or below the Earth's surface. It aims to simplify reporting of energy and mineral reserves and resources in a globalized world and is intended to improve global communications regarding remaining quantities of non-renewable fossil energy and mineral resources. The UN Classification is not recognized as a Foreign Code under NI 43-101.SECTION I1.,The United Nations Framework Classification (UNFC-2009) applies to fossil energy and mineral reserves and resources located on or below the Earth' s surface. It serves the needs for classification at a global level (for energy and mineral supply studies), for governments (resources management and policy formulation), for industry (business process management) and for financial reporting.SECTION II2.,The UNFC is a generic system in which quantities are classified on the basis of the three fundamental criteria of economic and social viability (E), field project status and feasibility (F), and geological knowledge (G), using a numerical coding system. Combinations of these criteria create a three-dimensional system. Categories (e.g. El, E2, E3) and, in some cases, sub-categories (e.g. E1.1) are defined for each of the three criteria as set out and defined in Annexes I and II.3 The first set of categories (the E axis) designates the degree of favourability of social and economic conditions in establishing the commercial viability of the project, including consideration of market prices and relevant legal, regulatory, environmental and contractual conditions. The second set (the F axis) designates the maturity of studies and commitments necessary to implement mining plans or development projects. These extend from early exploration efforts before a deposit or accumulation has been confirmed to exist through to a project that is extracting and selling a commodity, and reflect standard value chain management principles. The third set of categories (the G axis) designates the level of confidence in the geological knowledge and potential recoverability of the quantities.4. The categories and sub-categories are the building blocks of the system, and are combined in the form of ""classes"". The UNFC can be visualised in three dimensions, as shown in Figure 1, or represented in a practical two-dimensional abbreviated version as shown in Figure 2."

Jan 1, 2003

By H. Utsunomiya

Most magnesium alloy sheets show low deformability in rolling. Edge cracks and transverse fractures are common difficulties. In addition, rolled sheets show well-developed basal texture <0001>//ND. The texture causes high anisotropy in mechanical properties and low formability in subsequent metal forming. Differential-speed rolling, where the upper and the lower rolls rotate at different speeds, introduces shear deformation through the thickness. Not rolling texture but shear texture evolves in the sheet so that the asymmetric rolling can be a method of texture control. However the primary slip system of the hcp alloy, is basal, the shear texture should be also basal. Differences between the two basal textures, i.e., the rolling texture and the shear texture, have not been understood completely. In this study, conventional (same-speed) rolling and differential-speed rolling have been applied to commercial AZ31B sheets at 623K. Microstructures, textures and mechanical properties of the rolled sheets before/after annealing are compared. It is found that the basal texture is more pronounced by the asymmetric rolling. On the other hand, the asymmetric rolling is effective to decrease the grain size and the planar anisotropy.

Jan 1, 2006

By V. Songmene, R. Khettabi, J. Masounave, R. D. Njoya

L&apos;augmentation régulière des règlements environnementaux et de la sécurité au travail deviennent de plus en plus strictes. L&apos;usinage fait partie des opérations industrielles qui peuvent causer des problèmes de santé au travail et sur l&apos;environnement. La plupart des particules de poussières produites pendant toutes les opérations d&apos;usinage à sec ou lubrifie causent des nuisances environnementales graves. Le travail propose étudie l’influence des paramètres de coupe, des alliages et des états des matériaux sur la formation des copeaux et sur la génération de poussière lors de l&apos;usinage à sec. Deux modes d&apos;usinage (le fraisage et le perçage) sont abordés. Une loi reliant la ténacité des matériaux aux émissions de poussières est proposée. Les effets des matériaux et de leurs conditions, ainsi que des procédés d&apos;usinage sur la génération des poussières ont été mis en évidence. Des mécanismes de formation de poussières sont identifiés et reliés à la formation des copeaux.

Jan 1, 2006

By Richard Samson

"RésuméComme l&apos;exploitation d&apos;un gisement à grande profondeur représente un défi de taille et que la profondeur à laquelle se situe celui d&apos;Ansil varie de 1200 m à 1460 m, nous avons dû mettre en place une infrastructure de surface d&apos;envergure incluant un treuil de production et un chevalement d&apos;une très grande capacité. De même, l&apos;infrastructure sous terre a été proposée en tenant compte de ce fait important; d&apos;ailleurs, l&apos;excavation de deux puits circulaires dont l&apos;un est en beton et acier et l&apos;autre exclusivement en béton en témoigne. De plus, la plupart des cheminées principales qui furent excavées sous terre sont de forme circulaire.L &apos;exploitation du gisement s&apos;effectue par une méthode chantier ouvert (abattage par longs trous), remblaye immédiatement âpres avec un mélange de roche stérile et ciment. Un taux de minage de 1750 tonnes par jour est requis pour assurer la production.L &apos;utilisation d&apos;une technologie de pointe tels: les ventilateurs et les portes de ventilation sous terre contrôlées de la surface, un système de relèves macroséismiques, de chargeuses-navettes contrôles à distance, en passant par le dessin et la planification assistes par ordinateur nous permet d&apos;optimiser l&apos;exploitation du gisement Ansil.IntroductionEtant donne la grande profondeur a laquelle le gisement Ansil se situe, no us avons à mettre en place une infrastructure souterraine et de surface d&apos;envergure pour nous permettre d&apos;atteindre nos objectifs d&apos;exploitation.Infrastructure de surfaceLa mine Ansil dispose d&apos;une infrastructure de surface d&apos;importance possédant une grande capacité (Fig. I). Les deux facteurs qui furent déterminant pour le dimensionnement des infrastructures furent le taux d&apos;extraction de 1990 t/jour et la profondeur a laquelle I &apos;exploitation s&apos;effectue, puis que cette dernière affecte le temps de cycle et la capacité de hissage.La première composante principale de I &apos;infrastructure de surface est un treuil de production a 2 tambours de 3.65 m de diamètre et de 2.0 m de largeur chacun. Ce treuil de marque Fullerton, Hodgart & Barclay construit en 1970, opère avec 2 moteurs de 930 kW a une vitesse de 700 m/min. et il a une capacité maximale de 32000 kg. Deux câbles d&apos;acier de 45 mm de diarnètre et de 160 000 kg de résistance a la rupture servant au hissage des bennes d&apos;une capacité de 12 tonnes. De plus, un moteur/générateur de 3000 kW (M.G. Set) raccorde au treuil de production sert a stabliser son alimentation électrique."

Jan 1, 1991

By Pierre Montrueil, Marcel St-Amant

Within the next few years, underground mobile equipment will be partially automated. Mining methods will integrate more and more automation. Such an evolution will be possible only if adequate underground communication systems are developed. This is expected due to the available competence in Canadian telecommunication, to the economic pressure on the Canadian mining industries for international competitiveness and to the social changes where a better working environment (i.e. less accidents) becomes a major concern. CCARM propose the concept of a Production Area Network for Automated Mobile Units called PANAMU as an intermediate size communication system. It can be implemented using mature present-day technology and it can be integrated in some mine wide communication systems. It can evolve so as to incorporate new technologies because of its modular concepts. In this paper, the communication requirements are estimated, the amtmptions are defined, the concepts of the PANAMU are presented and an over- view of its implementation is described. CCARM presents this article to the mining industry as a document for discussion.

Jan 1, 1994

By R. W. Nice

"For many decades the incidence of a highly active graphite-like ore has plagued the McIntyre mine. This ore acts as a precipitant of the gold complex immediately upon formation of this complex. The gold is subsequently discharged with the tailings.Many different methods have been devised by various researchers all of which proved inapplicable for the McIntyre problem.Recently, McIntyre personnel, through their own research, developed a flowsheet. This circuit should give an overall recovery of 36% which is below the 94% experienced in the mill at present. Therefore, less revenue would arise from treatment of these ores. On the other hand there exists a possibility of more efficient mining methods in some of this ore thus allowing more economic recovery.INTRODUCTION This paper has been prepared to serve two purposes:i) To propose a method of recoverying gold from a sizeable orebody at the McIntyre mine at Schumacher.ii) To summarize and present the many methods suggested to solve a very old but very real mineral dressing problem familiar to the industry as long as cyanidation itself."

Jan 1, 1971

By S. Kodama, G. Sasaki, K. Matsugi, K. Sugio, Y. B. Choi

"Pure aluminum (Al) matrix composites with changing the volume fraction of TiB2 particle content from 10 to 30% was fabricated by spark plasma sintering (SPS) process. Then the microstructure, density, dispersibility and thermal conductivity of the composites was estimated. As increasing TiB2 content, the dispersibility of particles and the density of the composites degraded slightly. And, the effect of the dispersibility of TiB2 particles on the thermal conductivity was quite little. The thermal conductivity of the composites was less than the theoretical value calculated by Maxwell-Eucken equation considering the effect of the density. It is due the influence of the interface heat transfer rate, because these composites have many small sized particles and have high interface density.INTRODUCTION Recently, metal matrix composites (MMCs) have been used widely in electric / electronic components, architectural materials, transportation equipment, aerospace and a precision instruments, because it’s superior properties have been greatly watched. Demand of MMC for industrial use has been increasing gradually. Furthermore, multifunction properties are required for the composites strongly. By integrating the dissimilar materials, the composites have various properties that we cannot get from monolithic materials. On the other hand, the response to the thermal management is required for materials, recently, and the need for the structural material controlling the thermal conductivity has been increasing. Especially, superior thermal conductivity and good mechanical properties from room temperature to high temperature are required for heat sink and heat exchanger at the same time. In late years, a study on the composites combining carbon materials and aluminum and copper has been developing, and actually the composites with high thermal conductivity which is not provided in the conventional materials is developed. On the other hand, non-oxide ceramics particles such as SiC and AlN, TiB2 have good thermal conductivity. Particularly, as TiB2 has good electrical conductivity, TiB2 containing MMCs is expected as innovative materials used as electric/ electronic components. Furthermore, as TiB2 has low density, high melting point, low thermal expansion and good deformation resistance, the development of high performance composites with multi-functional properties is expected. As thermal conductivity of pure Al and TiB2 are 225 and 66.4 W/mK, respectively, it is expected that the degradation of thermal conductivity by adding dispersant in Al matrix is suppressed. The authors have carried out a thermal conductivity, electrical conductivity, mechanical properties of 20 vol.% TiB2 dispersed Al composites (Sugio, 2016, Sasaki, 2016). In this study, the influence of quantity of addition of TiB2 on microstructure, thermal conductivity was studied minutely."

Jan 1, 2018

By Pierre Beaudoin, Michel Bourassa, Robert Lanthier, Samir Chéfaï

"Mine Doyon, in collaboration with CRM's Process Control Division, improved the control strategy at the SAG mill I Ball mill grinding circuit. The project aimed at increasing operation stability and throughput. First, a needs analysis was achieved in order to define the control philosophy and to upgrade the process control equipments and instrumentation. The stabilizing control strategy has been developed and implemented successfully using single loop PID controllers. The monitoring feature as well as the rule based supervisory control strategy were implemented on 486PCs running Process Vision and COMDALE/C softwares. Main features of the control strategy are described in this paper while results are presented and discussed.RésuméLa Mine Doyon, en collaboration avec le service de contrôle des procédés du CRM, a optimisé la stratégie de contrôle au circuit de broyage. Les objectifs du projet étaient !'amélioration de la stabilité de !'ensemble de !'opération et la maximisation du tonnage usiné. Une analyse de besoins a été réalisée pour concevoir la philosophie de contrôle et déterminer les ajouts a apporter a I 'instrumentation et au systeme de contrôle. Une stratégie de contrôle à deux niveaux, integrant stabilisation et supervision, a été developpee et mise en opération. La regulation est réalisee par une combinaison de contrôleurs Moore de type PID. Le monitoring et la stratégie de contrôle a base de règles soot implantés sur des micro-ordinateurs de type PC/486 avec les logiciels ProcessVision et Comdale/C. Les principaux aspects de Ia stratégie de contrôle sont décrits dans cet article et les résultats obtenus soot présentés et discutés."

Jan 1, 1995

By Robert D. Brown

"On April 22, 1980, the Ontario government introduced a totally new incentive program for mineral exploration in the province to be effective September I, 1980. Replacing the former Mineral Exploration Assistance Program (MEAP) and also the assistance formerly provided to the mining sector under the Small Business Development Corporations Act, the new Ontario Mineral Exploration Program (OMEP) promises to offer a valuable benefit to certain eligible applicants.Unfortunately, the program is not without its shortcomings: the eligibility for grants or tax credits under the program is comparatively restrictive, and an October 1980 federal budget provision to amend income tax legislation would blunt some of the originally intended attractiveness of the grants and credits.IntroductionIn his budget of April 22, 1980, Ontario Treasurer Frank Miller introduced a new incentive program to encourage mineral exploration in the province.The Ontario Mineral Exploration Program (OMEP) replaces the Mineral Exploration Assistance Program (MEAP), which will be phased out by March 31, 1981. Exploration programs approved under MEAP will continue to qualify for incentives under that program, but will not qualify for OMEP."

Jan 1, 1981