Search Documents

By J. H. Pee, Y. J. Kim, H. U. Lee, G. H. Kim

The general recycling process of tungsten scrap to produce tungsten raw materials (tungstic acid, ammonium paratungstate (APT) and WO3) have been carried out by the oxidation, milling, sodium-fusion, dissolution, and extraction processes. Many studies on the high temperature oxidation of tungsten scrap have investigated various aspects such as swelling kinetics, fracture resistance, and the effect of alloying composition. However, the accelerating factors on the scrap oxidation rate during oxidation were not considered here. In general, oxidized products were fused with sodium carbonate or sodium hydroxide to produce Na2WO4. Later in the process, solid Na2WO4 was dissolved in water. This process required considerable reaction time and was a costly process. Therefore, the aim of this study was to increase the solubility of solid oxidized products to produce Na2WO4 solution by hydrothermal reflux method. Na2WO4 solution was used to produce CaWO4 and H2WO4 by general chemical reactions with calcium chloride and hydrochloric acid. Ammonia solution was also added to the tungstic acid to produce APT. In this study, the effect of ammonia addition on the APT precipitation process was investigated in detail.

Jan 1, 2015

This paper discusses three case studies conducted at Highland Valley Copper mine (HVC) that illustrate operational improvements and insights which resulted from using the McGill University gas dispersion sensors. In the first study, the superficial gas velocity (Jg) sensor was used to implement a gas profiling control strategy for the rougher, scavenger and first cleaner cells in the Cu/Mo separation circuit. The data showed a 40% reduction of down-the-bank Cu recovery at constant Mo recovery which resulted from operating the cells at the target profiles. In the second study, the bubble size analyzer was used to better understand two mechanisms of bubble formation in the two flotation columns that make up the final Mo cleaning stage: the conventional rubber-sleeve sparger and the Microcel(TM) system. The data showed a considerable reduction of bubble size in the Microcel column which resulted in a significant increase in concentrate quality (1-2% Mo absolute) and a dramatic (4-5 fold) increase in concentrate production rate compared to the typical operation. The estimated economic benefit resulting from the improved column flotation operation was an overall 4% increase in Mo circuit recovery. In the third study, real-time measurements obtained from the gas holdup and bulk density sensors were used to infer the pulp density (% solids) in a rougher cell of the bulk flotation circuit. Validation tests demonstrated that this approach provides reliable pulp density measurements. Although promising, more work is required before implementing this approach at HVC.

Jan 1, 2009

By L. S. Beck

"IntroductionThe Beaverlodge District is an important mineralogenic province of pitchblende and occupies about 1300 square kilometres centred on Beaverlodge Lake near the north shore of Lake Athabasca in northwest Saskatchewan (Fig. 1). Uranium City is the main settlement of the area and is serviced by scheduled aircraft from Edmonton, some 700 km to the southwest, and from Prince Albert which lies a similar distance to the south.During the summer, boats and barges supply the area from the railhead to Fort McMurray via the Athabasca River and Lake Athabasca, a distance of about 550 km. For the past few years a winter road has been maintained across Lake Athabasca to Cluff Lake to connect with Highway 155.The topography of the area is typical of the Precambrian Shield with generally low relief and a disorganized drainage of numerous lakes separated by hummocky rock ridges, muskeg and drift-covered areas. Local topography in the area is, however, extremely rugged, particularly south and east of Beaverlodge Lake, where resistant rocks form prominent hills and ridges extending as much as 180 m above lake level. Rock exposures are abundant and form over 50 per cent of the land area.History of Exploration and DevelopmentEconomic interest was first aroused by Tyrrell (1896) who described an occurrence of iron formation at Fish Hook Bay; however, subsequent evaluation of the deposit indicated it to be uneconomic."

Jan 1, 1986

By James F. A. Hatley

Northern Saskatchewan comprises an area of about 350 000 km2 and boasts some of the world's largest known high-grade uranium deposits. The successful mining of these deposits, however, can not be accomplished without overcoming technical challenges. Not only is the high grade of the uranium ore challenging, but mining methods need to be developed to deal with groundwater at very high pressures, and ground conditions that vary substantially from excellent to wholly unconsolidated clays and sand. This paper discusses the various mechanisms of inflows at the three of the Cameco Corporation Mines in Northern Saskatchewan. The risk of inflows is quantified in terms of unique challenges from hydrogeologic conditions, rockmass integrity, and uncertainty in geologic conditions. Mitigation strategies in case of an inflow are also briefly described. The paper concludes by addressing the impact of institutional rules (corporate standards) on minimizing, monitoring, and controlling the probability and/or impact of unexpected inflows.

Aug 1, 2010

By David S. Robertson, Richard F. Douglas

"Uranium is a lithophile element of relatively low natural abundance. Concentrations of uranium form through processes of erosion and sedimentation, and over 90 per cent of the western world's uranium ore reserves are in sedimentary rocks.Proterozoic quartz-pebble conglomerates contain about 60 per cent of the known uranium reserves. These are all similar in appearance, in mode of distribution and in manner of origin. They carry uranium minerals and/or gold and abundant pyrite. Their unique distribution in Huronian time required a pre-existing crust well enough evolved to have plentiful quartz and abundant gold, uranium and pyrite. The materials of value were deposited as detrital heavy minerals prior to the appearance of an oxidizing atmosphere in late Proterozoic time.Epigenetic uranium deposits occur in arkosic sedimentary rocks through the entire geological column. About 30 per cent of the western world's known ore reserves are in _these rocks. This type of deposit is particularly prominent in semi-arid parts of the United States, having yielded most of the uranium ore produced and containing nearly all of the known reserves.The Western States type"" of deposits occur in lenticular, permeable stream-laid sedimentary rocks. The de-posits are believed to have been precipitated from moving ground water at locations where plant debris or other organic matter had accumulated. The uranium may be derived from volcanic sediments, which are commonly associated with the units containing the ore, or it may be leached from exposed granite surfaces or from granitic debris which forms the sediments.A significant part of the world's uranium resources are in black shales and lignitic rocks. The lignites that contain uranium are virtually valueless as potential sources of heat. Uranium concentrations at levels such as to be potential sources of by-product uranium occur in many phosphorites.Reworked sediments may provide uranium in pegmatites and vein-like deposits."

Jan 1, 1970

By Ken McClure, Alex Day

Located North of Williams Lake British Columbia, Gibraltar Mine is the fourth largest open pit Copper mine in North America. Gibraltar commenced Copper concentrate production in 1972 with a mill throughput rate of 30,000 tons per day. A series of expansion projects, including installation of a second SAG mill with variable speed drives in 2013, has increased mill throughput to 85,000 tons per day. Over the past 24 months, Gibraltar Mine in partnership with Spartan Controls has executed several advanced process control programming projects culminating in the implementation of a Continuous Speed Controller (CSC) for the most recently installed SAG mill. This paper covers development and results for the SAG mill speed controller. INTRODUCTION In January 2016, the price of Copper fell below $2.00 USD per pound, the lowest price in 7 years. Gibraltar Mine faced a significant challenge; how to maximize profit in an environment where capital spending was not an option. An opportunity was quickly identified to improve performance through increased automation and advanced control of the grinding processes. Beginning in March 2016, Gibraltar Mine partnered with Spartan Controls to introduce Advanced Process Control (APC) to the grinding circuits. The collaboration between metallurgical and process control engineering disciplines proved to be effective for achieving gains in throughput, reliability and productivity for the mill process. The Gibraltar milling facilities include 2 grinding-flotation plants for concentration of chalcopyrite ore with throughput rates of 58,000 tons per day (Concentrator 1) and 38,000 tons per day (Concentrator 2). Each of the two concentrators has a 34’ diameter SAG mill powered by 2 GE 4800 kW synchronous electric motors. For SAG 1 (in concentrator 1), power is transmitted through 2 Eaton Airflex clutches. For SAG 2 (in concentrator 2), the motors are driven by 2 TMEIC Variable Frequency Drives (VFDs). All programming is done using DeltaV, which Gibraltar uses as its Distributed Control System (DCS) and Human Machine Interface (HMI).

Jan 1, 2019

By R J. Tremblay, R. R. Hoffman

This paper deals with materials of construction and problems encountered and overcome in leaching and filtration of oxidized sulphuric acid slurry in the Port Radium mill after eight years of operation. The slurry is characterized by a high calcium sulphate content as well as a high chloride level under oxidized conditions, both of which affected initial design and subsequent changes. Leach agitation tanks are of wood with a mild steel superstructure and stainless steel agitator and moving parts below solution level. Electro-polished 316 stainless steel cooling coils are used for temperature control of the slurry. The string filters are of the Oliver type with wood decking. Extensive use is made of wood, Linatex lined mild steel and stainless steel for the slurry handling. A typical analysis of the slurry solution follows:(pH-1.30) ClOa Fe+++ Free Acid UaOs c1-so.--0.10 gms/litre 10.2 gms/litre 6. 7 gms/litre 3.5 gms/litre 2.0 gms/litre 155 gms/litre

Jan 1, 1961

By Alexander Burns, David Dreisinger

The kinetics of the oxidation of uranium(IV) by oxygen gas in aqueous systems is dependent on acid concentration, oxygen partial pressure, and temperature. In order to better understand the relationship between these variables and the speed of oxidation, a series of experiments have been conducted where each parameter has been varied in turn. Data were collected continuously using UVVis spectroscopy, allowing for a detailed examination of the reaction rate over the course of each experiment. The data fit an overall apparent rate law that is 1.5order in uranium(IV), -2order in H+, first order in oxygen, and unaffected by uranium(VI). This relationship does not appear to hold for solutions with <0.2 mol/L initial acid, where a different kinetic mechanism appears to be dominant.

Jan 1, 2014

By Yosuke Ota, Makoto Tawara, Tetsuya Kojima

"Dry-lube has been used in Europe to enhance formability of aluminum sheet for automotive applications, but it is difficult to ensure degreasing performance with lower degreasing bath temperature. However, newly developed, highly lubricating pre-coats utilizing a urethane resin, which is soluble in water, have been found to show excellent degreasing performance. Furthermore, a richer pre-coat weight coincides with a lower friction coefficient and better formability. Combined use of anti-rust liquid oil showed different friction coefficient depending on applied surface pressure.INTRODUCTION The global demand for aluminum alloy products, especially for automotive application, has been increasing because aluminum alloys can offer excellent corrosion resistance with good strength and low density compared with steel. Aluminum alloys can contribute to saving much more energy and greenhouse gas emissions over the lifetime of the product. On the other hand, the amount of aluminum alloys in vehicle architectures is still somewhat limited due to relatively low formability. As a consequence of this low formability, it is necessary to set a certain limit to the shape of an aluminum alloy panel for automotive applications. So far hot melt wax dry lubricants have been in use especially in Europe as they have been recognized to provide better lubrication than conventional rust protection oils (Meiler & Jaschke, 2005). The benefit of hot-melt wax for automotive manufacturing is associated with a more stable forming process and the possibility to avoid extra lubrication in the press shop. But because of the low poorer solubility of hot-melt wax in degreasing aqueous bath solution, a higher degreasing temperature is required so that no remnant of hot melt wax can be carried over to the next manufacturing process. This temperature control is difficult to impress upon a manufacturing degreasing bath originally designed for liquid oil, especially in Japan. The typical temperature of degreasing bath in Europe is around 60°C, while it is only around 40°C. in Japan. Various types of pre-coats other than hot-melt with high lubricity have been reported (Tawara, 1993; Ueda, Hatsuno & Totani, 2013), but a balance between sufficient degreasing performance and high lubricity has not yet been achieved for an actual production process line."

Jan 1, 2018

By James D. Hall

THE Dome ore-bodies are more or less isolated and are mined. by shrinkage stoping. An interwoven system of veins is mined at Hollinger &apos;.1.nd requires close filling. Deep mining is the problem at McIntyre. Dome ore contains a large amount of free gold, which is recovered on blankets. An all-cyanide flow-sheet is \lSed in the Hollinger mill. Flotation concentration is an important feature of McIntyre mill operation. Therefore, these three mines afford an unusual opportunity to compare gold mining and milling methods. The purpose of this paper is to describe the conditions existing at the Dome, Hollinger, and McIntyre mines and to outline the mining and milling practice at each property. Figures 3, 4, 5, and 7 are reproduced from the Canadian Mining ]011rna/, September, 1935 (Young, A. W., Mining at Hollinger), and Figures 8 to 11 from the Engineering and Mining Journal, November, 1933 (Keeley, D. E., Development and Mining at McIntyre). The photographs (Figures 6, 12, and 13) are by The Canadian Government Motion Picture Bureau. Diagrams of the several mill flow-sheets, which formed a part of the original paper, are not reproduced here. They will be found in Dorr&apos;s Cyanidation and Concentration of Gold and Silver Ores.

Jan 1, 1938

By F. Barriga-Ordonez, J. A. Finch, L. Calzado, S. R. (Ram) Rao

Sludge, formed by lime treatment of acidic drainage and stored in tailing ponds of the Sudbury region, contains 5-7% Ni, mostly in a mix of hydroxides with Fe (~ 10%), Mg (~ 10%) and Cu (-0.5%), and Ca (-3.5%) as sulphate. Investigations were conducted to recover nickel by a 2-stage process. In the first stage, the sludge was leached with sulphuric acid at pH 3.2. About 90% of the nickel was extracted, producing a solution, which contained mainly nickel (2 g/L) and magnesium (3.7 g/L). In the second stage, nickel was separated by treating with ozone which recovered 99% of the nickel in the Ni(III) oxidation state as -85% pure nickel oxide-hydroxide (NiOOH) precipitate. The oxide settled and filtered readily. A potential use of the product in battery making is suggested. The leach residue contained 0.5% Ni making it less toxic for disposal. Some physical properties of nickel oxy-hydroxide and process parameters including ozone consumption will be discussed.

Jan 1, 2005

By C. Blawert

The corrosion properties of the skin and the bulk of semi-solid processed and high pressure die cast AZ91 alloy were studied in 5% NaCI solution by (a) analysing the corrosion morphology, (b) measuring electrochemical polarization curves, (c) performing electrochemical impedance spectroscopic measurements, and (d) immersion tests at constant pH-values. Using XRD, LM, SEM and EDX to evaluate the microstructure of skin and bulk specimens, the corrosion results were related to the microstructures of the particular alloys. However, microstructure and corrosion performance were found to be similar for both production processes, and only slight but distinct differences were found. Generally, the skin corrosion properties are inferior to those of the bulk, with the exception of the high pressure die cast AZ91 alloy, where the finer microstructure of the skin layer exhibits a better performance as showed by impedance studies and confirmed in long term immersion tests.

Jan 1, 2004

By Yin Wang, Lin Li, Zhongwei Bi, Like Wei, Wen Li, Shaogang Li, Bin Zhang, Hongjie Li

Presently,Many long-wall fully-mechanized faces in shallow depth coal seams are below room and pillar goaf in Shendong mining area. When the working face is advanced out of concentrated coal pillar in upper room and pillar goaf, strong strata behaviors often cause support crushing accident. Aiming at a support crushing accident which happened in Shigetai coal mine of Shenhua group in Shendong mining area, this paper analyses the stress transfer process while mining out of concentrated coal pillar by numerical simulation software FLAC3D. According to the feature, simplifying the roof of upper room and pillar goaf as supporting-beam structure explains mechanism of large area collapse in room and pillar goaf roof. Based on the feature of supporting-beam structure, deep-hole blasting concentrated coal pillar technology is proposed to control the strong strata behaviors in Shigetai coal mine. The blasting control effect is confirmed through characteristics of strata behaviors, growth circumstance of ground crack and multi-point extensometer monitoring results. By using control technology, Shigetai coal mine has been successfully avoided support crushing accident.

Jan 1, 2015

By E. L. Bruce

EUROPEAN Russia is mainly a great plain, the average elevation of which is only 600 feet above sea level and the maximum elevation less than 1,200 feet (Figure 1). The main divide between the Arctic ocean and the Black sea and Caspian sea is an indistinguishable topographic feature from which the Dneiper and Don rivers flow southward to the Black sea and the Volga river to the Caspian. The valleys of these rivers are but little below the general level (Figure 2). To the south, this great, rolling plain is broken by a low ridge of Precambrian gneisses and intrusive rocks. The Crimea is an upland from which the descent to the Black Sea coast is precipitous (Figure 3). The Ukrainian Soviet Socialist Republic occupies the southern part of the plain. It is the southwestern unit of the Union, bordered by Rumania and Poland on the west and by the Crimean Soviet Socialist Republic on the south.

Jan 1, 1938

By K. E. Waters, N. Brodusch, R. Gauvin, H. Demers

"Rare earth elements are becoming increasingly in demand, due to their prevalence in both renewable energy devices and high-end electronics. The characterization of the composition, morphology and volume fraction of the various phases that have valuable rare earths in the ores are needed to find the optimal industrial process to extract the ores containing the rare earths. Rare earth-bearing minerals contain many elements with the M-and L-lines overlap, requiring a high degree of resolution, pushing the boundaries of scanning electron microscopy quantitative analysis. Enhanced microscopy at a high spatial resolution with improved x-ray quantitative analysis enables the accurate determination of the distribution of the desired rare earths in various mineral phases. INTRODUCTIONRare earth elements are becoming increasingly in demand, due to their prevalence in both renewable energy devices and high-end electronics. From batteries (lanthanum and cerium), to magnets (dysprosium and neodymium) and lighting (yttrium), the rare earth elements are crucial to the advancement of technology, and to energy saving devices (Crow, 2011). The goal of this project is to characterize the composition, morphology and volume fraction of the various phases that have valuable rare earths in the ores in order to estimate the economical VALUES (of the ores and to find the optimal industrial process to extract the ores containing the rare earths. High spatial resolution imaging and x-ray microanalysis are needed to reach this goal. In this work, the results obtained with a cold-field-emission scanning electron microscope (FE-SEM) and a silicon drift detector (SDD) energy dispersive spectrometry (EDS) detector at low accelerating voltage are compared to experimental conditions typically used with electron probe microanalysis (EPMA) instrument.With this improvement, a detailed scientific analysis of the composition of these, and other, ores will become possible with a SEM/EDS system. This will help to better understand how such ores were formed, hence assisting in finding them, and to better understand how to process them in preparation for high end industrial applications, namely through mineral processing."

Jan 1, 2012

By John A. Dresser

At a meeting of the Montreal Branch of this Institute in the autumn of 1928, the Honorable J. E. Perrault, Minister of Mines for Quebec, announced his intention to enlarge the Bureau of Mines of Quebec by the addition of a Division of Geology. The announcement further stated that the geological work proposed should be begun in the following field season, and that it should be on a substantial scale of not less than six field parties. The announcement was received with enthusiasm and much encouragement was held out for the success of the effort. It has been thought that the present meeting would be a suitable occasion to present a report of progress of this Division for the three years that have since elapsed. History This, of course, is not the first geological work to be undertaken by the Bureau of Mines. Prior to the establishment of the Division of Geology, the Bureau of Mines had not been unmindful of the need of geological research, but it had always lacked the means necessary to any sustained work. For more than 25 years the late J. Obalski was the Superintendent and the sole occupant of the Bureau. Yet, even then, Obalski, besides routine visits to mining districts, made a few exploratory trips along the north shore of the St. Lawrence river and one to Chibougamau, but without the equipment necessary to effective results.

Jan 1, 1932

By W. A. Jankola, M. T. Martin

"The world&apos;s first zinc pressure leaching plant at Cominco&apos;s Trail operations started production in 1981. Sullivan zinc concentrate is leached at the rate of 190 tpd in a four-compartment autoclave at elevated temperatures and oxygen pressures to produce a zinc sulphate solution and elemental sulphur. Zinc extraction exceeds 98% and sulphide to elemental sulphur conversion exceeds 95%.The sulphur is recovered from the discharged slurry in the underflow of a hydrocyclone, and is upgraded as a flotation concentrate. The concentrate is dewatered, melted and filtered to produce a polished sulphur product of better than 99% purity. An alternative sulphur recovery process employs an unique sulphur separation method that recovers over 90% of the sulphur in the molten state. The remaining sulphur is recovered by flotation following flash discharge of the slurry. The product slurry containing the zinc sulphate solution and the iron-lead residue joins the existing roast-leach zinc plant for purification and zinc electrowinning.IntroductionIn 1981, Cominco Ltd. commissioned the world&apos;s first commercial zinc pressure leaching plant at their Trail operations in British Columbia. As part of a $700 million modernization and expansion program for lead and zinc started in 1977, the company installed the first o f two autoclave trains.Prior to pressure leaching, zinc production was closely tied to acid and fertilizer production. Sulphur dioxide produced from roasting the concentrates had to be converted to sulphuric acid. Thus, any expansion of zinc operations with the roast-leach technology would have required extensive modifications to the acid and fertilizer plants as well as to the roasters. Zinc pressure leaching, on the other hand, offered a one-step dissolution of zinc from the concentrates with high extraction, and production of elemental sulphur. The associated dust and sulphur dioxide generated in the roasting process are both eliminated from the working environment of the pressure leach facility. The flexibility allowed by producing elemental sulphur, and the opportunity to break the sulphuric acid link for about 25 per cent of the targeted 272,000 tonnes per year zinc production was very appealing. The process was successfully demonstrated at a pilot plant in 1977(1-6)."

Jan 1, 1985

By A. Musschoot

"The paper will review general types and designs of vibratory feeders, describing briefly the design features and characteristics that apply to the application of specific types. Control considerations for selecting types will be dis• cussed, such as fixed or adjustable, manual or automatic, individual or multiple bank, and process requirements. Design parameters for hopper openings and installation geometry will be discussed, including consideration of material size distribution, segregation, moisture content and other characteristics, based on practical applications and experience as well as theory. Pan designs and the selection of pan materials will also be discussed with reference to wear, corrosion, impact and practical economic factors."

Jan 1, 1972

By Richard E. Barrett

SOME YEARS AGO I was associated with a mining operation which, because of its isolated location, burned wood for heating purposes. Year after year the tractors and tucks hauled the cordwood in from the edge of the ever-growing clearing. Each year the cartage costs became greater. The degree to which transportation distances affect the economics of fuels obviously varies with many factors, but the main criterion is the amount of heat a unit weight of the fuel will produce. For in-stance, wood is limited in most cases to a haulage distance of a few miles. Coal can be shipped hundreds of miles, whereas petroleum and gas ?can be transported thousands of miles. The world is now on the brink of having a new fuel -uranium. It has the virtue of being so concentrated that transportation costs can, for all practical purposes, be disregarded.

Jan 1, 1958

By A. Saigal

The effect of temperature on the cutting forces during machining of alumina reinforced aluminum composites was investigated, Aluminum 6061, 10% Al2O3 reinforced composite and 20% Al2O3 reinforced composite were tested, A 5/8-inch diameter high-speed steel end mill, a Micro 100 TiN coated single edge endmill cutter and a two-fluted solid carbide insert cutter were used for tooling, The results, in general, showed an increase in the cutting forces as the temperature of the material increased, From the raw data, there are temperatures ranges in which the force data did decrease but they were insignificant with regards to predicting a downward trend. A regression analysis was used to understand which variables had the greatest affect on the forces being generated, The correlation and regression analysis showed that at 600 rpm (velocity: HSS- 98,2 sfpm, Micro 100 cutter - 78,5 sfpm, solid carbide cutter - 192,4 sfpm) the tooling, the workpiece material, built up edge, and temperature were statistically significant factors in the test, Tooling was a significant variable in all testing, The smallest forces recorded during machining were generated with the solid carbide two-fluted endmill cutter, Visually, the solid carbide tooling produced a better surface finish during the testing which made it the tool of choice, In addition, the force data proved that as the cutting speeds were increased, the cutting forces decreased.

Jan 1, 2005