Search Documents

By S. Orangi

A representative sample of ramming paste from a peripheral seam in an aluminium electrolysis cell was taken in order to develop a process to fabricate ramming paste samples in the laboratory. To this end, paste material was compacted in multilayers in a mould designed to be representative of peripheral seams in Alcoa's smelters. The density distribution in the representative sample was measured ranging from 1.51-1.76 g/cm3. The density range obtained by the proposed methodology in laboratory is 1.47-1.77 g/cm3. The results demonstrate that the proposed fabrication method adequately duplicates paste density from the cell for both one and two layer compaction. Finally, preliminary results related to the compressive strength and Young's modulus of laboratory samples were obtained at various temperatures and are presented in this paper.

Jan 1, 2011

By Joseph Licavoli, Paul Sanders, Yang Yang

"Al-Sc-Zr alloys form thermally stable L12 precipitates which provide high temperature strength. Although the overall fraction of L12 Al3Sc and Al3Zr may be increased by increasing scandium (Sc) and zirconium (Zr) content, such additions may increase primary phase fractions and do not produce desirable secondary phase morphologies. Rapid solidification techniques, such as melt spinning, increase solute atom concentration within the matrix. When the supersaturated matrix is aged, higher precipitate volume fractions at low Sc and Zr levels can be achieved improving high temperature strength. Melt spinning was used to rapidly solidify (107 k/s) a thin ribbon of Al-0.5Sc-0.4Zr at. %. The ribbon was compacted and extruded into 99.8% dense rods, and then aged using multi-step isochronal heat treatment up to 600°C. Precipitation strengthening was evaluated by ambient hardness measurement. The ambient hardness of melt-spun ribbon after precipitation hardening increased by 450 MPa (~67% increment) during isochronal heat treatment.INTRODUCTION Small Sc and Zr additions to aluminum improve strength and creep resistance above 300°C due to tri-aluminide precipitation of Al3(Sc,Zr) in L12 structures similar to ??, Ni3(Al,Ti) in nickel superalloy, but the Al3(Sc,Zr) particles have a Sc-rich core surrounded by Zr-rich shell (Figure 1). The Al3Zr shell limits atomic transport between the Al3Sc core and the matrix and reduces coherency strain. These factors reduce precipitate coarsening rate at elevated temperature (Bergner & Van Chi, 1977; Fujikawa, 1997; Knipling et al., 2011; Clouet et al., 2006).Figure 1. Simplified schematic model of precipitate Al(Sc,Zr) in Al-Sc-Zr alloy. Shell is rich of Al(Zr) intermetallic phase, particle core is rich of Al(Sc) intermetallic phase (after Voorhees, 2006). Numerous Al3(Sc,Zr) particles increase alloy strength and creep resistance as the precipitates impede dislocation glide and to a lesser extent climb. Previous work on ternary Al-Sc-Zr alloys show large strength increases versus binary Al-Sc, and Al-Zr alloys in Table 1."

Jan 1, 2018

By Yongfeng Jia, Shaofeng Wang, Danni Zhang

Arsenic in mineral processing solutions and effluents is commonly removed and immobilized via iron(III)-arsenatecoprecipitation. The effect of re-crystallization of 2-line ferrihydrite on the long-term stability of iron(III)-arsenate coprecipitate is still not fully understood. This work investigated the redistribution of arsenic and iron during 2-line ferrihydrite transformation at different pHs and temperatures over time. X-ray diffraction (XRD), transmission electron microscopy (TEM) and chemical extraction were employed to characterize the crystallinity of the iron oxyhydroxides. Results showed that the amount of arsenic released into solution during aging increased significantly with increasing media pH.

Jan 1, 2014

By K. Kawagishi, J. Ang, A. Sato, H. Harada

"We have recently proposed a new ""EQ Coating"" bond coat system to solve the problem of secondary reaction zone (SRZ) formation caused by bond coats applied on the hot section components of modem jet engines. A viable EQ coating alloy was previously found for a representative znd generation superalloy, TMS-82+. It would be ideal if the same could be done for a representative 5th generation superalloy, TMS-173. In this paper, we will show that the coating with the best oxidation resistance in the EQ system of TMS-173, although possessing considerably better resistance than TMS-173, did not have sufficient oxidation resistance. In order to improve the oxidation resistance of the EQ coating for TMS-173, we have ventured into ""Pseudo-EQ coatings"". A diffusion couple between the Pseudo-EQ coating and TMS-173, after 300hrs at 1100°C, had a 0-15µm IDZ, but no SRZ. A diffusion couple between a conventional coating and TMS-173 formed a 80-150 µm SRZ. After a 1 hr oxidation test at 1100°C, the PseudoEQ coating formed a thinner oxide layer than the EQ coating, but still contained NiO and spinel. Aerospace"

Jan 1, 2006

By R. Cottam

The deformation and recrystallisation of magnesium yttrium alloys containing 0.23, 0.84 and 2.71wt% yttrium and commercially pure magnesium extrusion has been investigated at temperatures between 200 and 350°C. The alloys were produced as billets 7.5 cm diameter, solution treated at 525 °C for 8 h and extruded into 3 cm diameter bar at 390°C. Channel die compression was employed to deform the samples at a strain rate of 1x10-3s-1. For the 0.23 wt% yttrium alloy and the pure magnesium, dynamic recrystallization (DRX) occurred at all temperatures and the amount of DRX increased as the temperature was raised. In the alloys containing 0.84 and 2.71 wt% yttrium DRX was almost completely suppressed at all temperatures. The absence of DRX in the 0.84 and 2.71 wt% yttrium alloys was accompanied by a decrease in the ductility, except at 350°C the highest deformation temperature. It was observed that this increase in ductility was accompanied by a reduction in deformation twinning and the initiation of pyramidal slip. This work highlights the important role that DRX plays in enhancing the ductility of magnesium alloys.

Jan 1, 2006

By Russell F. Palmer

"THE PRACTISING MINING ENGINEER has little time for the expression of opinion on abstract questions concerning the definition and future of mining engineering. The following comments indicate some of the thoughts and suggestions of those who have found mining engineering a very satisfying field of endeavour. The future of mining engineering has been under discussion for perhaps twenty years. It is significant that the University of Saskatchewan program was in- 88 traduced at the time that some traditional mining schools were questioning the need for mining engineers. One Canadian university, and some American schools, actually abandoned the field at this time, some ten years ago.Five years ago, Mining Magazine sponsored an international debate on training for the future, and concurrently, the CIM undertook a major survey of the mineral industry's manpower needs. The current CIM discussions should prove more fruitful, as they are directed toward mining engineering alone, rather than the broad, and confusing, spectrum of all professionals and semi-professionals of the mineral industry."

Jan 1, 1972

Slurry flow, including flow through the charge, through the discharge grates, along the pulp lifters and its discharge from the mill is an important contributor to the efficiency of the grinding process within a SAG mill. Poor transport of finer ground material can adversely affect grinding leading to excess energy consumption and over-grinding of fine material. This paper extends a 1-way coupled DEM-SPH method to three dimensions and applies it to a 1.8 m diameter by 0.6 m long AG/SAG pilot mill. This provides detailed information on the internal flow of slurry within a SAG mill, including the prediction of dry regions and of slurry pooling. Full 3D analysis also allows the pulp flow patterns into and out of the mill via pulp lifter chamber to be investigated.

Jan 1, 2012

By K. T. Aye

An investigation into the leaching of chalcocite and covellite in cyanide solutions at concentrations typically encountered daring gold cyanidation has been conducted. The results indicate that, for both minerals, the extent of leaching is greater under anoxic conditions, but is still incomplete even in the presence of free cyanide ions, with undissolved copper solids remaining in equilibrium with solution species. The speciation of the sulfur and cyanide reaction products in solution are interpreted in terms of the fast formation of a copper(I)- cyanide complexes in solution and a sulfur-rich copper(I) polysulfide solid phase, which then reacts more slowly to produce thiocyanate ions.

Jan 1, 2011

By A. Monballiu, J. A. Martens, Y. W. Chiang, A. Van Audenaerde, R. M. Santos, T. Van Gerven, B. Meesschaert

In this work, bioleaching of non-sulphidic materials by applying chemoheterotrophic bacteria and fungi is studied. It was found that the tested fungus, Aspergillus niger, leached substantially more nickel from olivine than the tested bacterium, Bacillus mucilaginosus. A. niger also outperformed fungal species Humicola grisae and Penicillium chrysogenum in the leaching of olivine. Contrary to traditional acid leaching, the microorganisms leached nickel preferentially over magnesium and iron. On average, a selectivity factor of 2.2 was achieved for nickel compared to iron. This can potentially facilitate postprocessing of the leach liquor and reduce the cost. The impact of ultrasonic conditioning on bioleaching was also tested, and substantial increase in nickel extraction with A. niger was observed. This was credited to an increase in the fungal growth rate, the promotion of particle degradation, and the detachment of the stagnant biofilm around the particles. Furthermore, ultrasonic conditioning enhanced the selectivity of A. niger for nickel, resulting in a selectivity ratio for Ni/Fe equal to 3.5. The chemical resistance of the selected microorganisms to several heavy metal and metalloid (As(III,V), Cd, Cr(III,V), Ni, Pb, Zn) was evaluated. It was found that, with the exception of As(v) and Cd, A. niger has high tolerance to these components. Therefore, this biohydrometallurgical route can potentially be applied to non-sulphidic wastederived materials, such as industrial slags, ashes and sludges.

Jan 1, 2014

By Gary Walters, Thomas Gonzales, David George, William Davenport, Andreas Siegmund, Suping Yao, Shijie Wang

The previous survey of world copper smelters was in 2016 (Copper, 2016). The copper smelting industry has grown and improved considerably since then, including continuing growth in China and modernization in Japan (Extraction, 2018). Outotec flash smelting and Outotec flash smelting/Kennecott - Outotec flash converting continue to be adopted while newer processes continue to be adopted in China. In addition, some of the world's original flash furnaces have been completely rebuilt (Extraction, 2018). This paper provides recent industrial production data and discusses these new developments. INTRODUCTION A world copper survey was redone in 2016 after a thirteen year lag since 2003. Some of the notable changes were the significant increases in production particularly from China. Since then, several smelters have gone through modernization processes and decommissioning of older technologies. This paper will review the notable changes since the last publication at Cu2016. In the last paper, Copper Smelting: 2016 World Copper Smelter Data, the author gave an audible sigh after observing that copper smelter sites as well as new and notable smelters have been spreading like wildfire in China since 2003. Indeed, seeing is believing. Figure 1 shows the Ningde Copper Smelter (double flashing, 400,000 MT Cu/Year capacity) that started up producing copper in 2018; Figure 2 shows the Nanguo Copper Smelter that is under construction with 300,000 MT Cu/Year capacity (first phase, side blown smelting and continuous top blown converting). We should not only admire the Chinese copper industry’s significant technological developments, but also the copper price support that it has provided throughout this century.

Jan 1, 2019

By D. G. Cerigo, D. M. Bryce, P. H. Jennings

This paper summarizes the results of an experimental and economic study undertaken to evaluate the feasibility of treating an oxidized orebody of about 10 million tons, grading about 0.75 per cent copper, by agitation leaching and by percolation leaching.

Jan 1, 1968

By M. Rafieazad, P. Fathi, X. Duan, M. Mohammadi, A. M. Nasiri

"Direct metal laser sintering (DMLS) is a metal additive manufacturing technology that creates highly complex components by fusing metal powder into a solid part. In this study, the impact of surface roughness on corrosion resistivity of AlSi10Mg_200C alloy manufactured through DMLS was investigated. The as-printed DMLS-AlSi10Mg _200C alloy was subjected to various surface finishing processes including grinding and sandblasting. The corrosion performance of the surfaces was then evaluated using potentiodynamic polarization testing and electrochemical impedance spectroscopy (EIS) in a 3.5 wt.% NaCl solution to mimic seawater environment. Surface characterization and corrosion morphology of the samples were assessed by Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray (EDX) spectroscopy. The results of this study show that the surface finishing process and the resultant surface roughness has a significant impact on the corrosion resistivity of the DMLS-AlSi10Mg_200C alloy in the seawater environment.INTRODUCTION Direct Metal Laser Sintering (DMLS), also known as Selective Laser Melting (SLM) (Sames, List, Pannala, Dehoff, & Babu, 2016), Laser Beam Melting (LBM), or Laser Metal Fusion (LMF) (Herzog, Seyda, Wycisk, & Emmelmann, 2016), is an additive manufacturing process that utilizes a precise, high-power laser to micro-join powdered metals and alloys layer by layer to form almost fully dense and functional components in three dimensions from the 3D computer-aided design (CAD) data. Complex geometries not possible with conventional manufacturing processes can be readily manufactured with high accuracy using the DMLS process with no need to time-consuming tooling."

Jan 1, 2018

In-Situ Leaching (ISL) process plants are low cost producers for uranium deposits where the geology is suitable. In the 1970s, a three-year pilot ISL program occurred on gold ore from the Ajax Mine, Cripple Creek District, Colorado, using a chloride and iodide solution [1]. The test was halted due to poor results. With gold and silver the international ISL progress has been slow; however the potential for low capital expenditure (CAPEX) and operating expenditure (OPEX) with large low grade deposits is real. Unless the metallurgy has been demonstrated there are significant risks which could be fatal flaws to an ISL gold or silver project. The metallurgy of gold ISL projects is far from simple and it is early days with project development.

Jan 1, 2011

By D. Neely

As Saskatchewan potash mines grow in age and size, mining reaches greater depths.  The stress-relief design principals which were empirically derived at shallower depths are beginning to show fault.  Nutrien Vanscoy Potash has began to encounter new ground support and panel design challenges which were previously had negligible effect.  While the initial reaction was to reduce extraction and implement distance buffers between operating machines, it eventually became clear that these would only provide short term relief and that in order to continue safely and efficiently mining broad areas, a fundamental change in the mine design would provide the long-term protection required.  Presented is a case study with an overview of the challenges encountered at Vanscoy Potash in areas of greater depth along with an account of the design changes considered, implemented and recommended for future success. 

May 4, 2025

"Discrete Fracture Network (DFN) modelling has increasingly being used in many geotechnical and mining engineering problems, the authors believe there is an ever greater demand to provide updated guidelines that address the collection of discontinuity data in the specific context of DFN models. In general terms, the generation of a DFN model requires collecting information on i) fracture orientation, ii) fracture intensity, iii) fracture length and iv) fracture terminations. The International Society of Rock Mechanics (ISRM) suggested methods for the quantitative description of discontinuities in rock masses directly include most of these parameters. However, there are important differences engineers should be aware. To what extent discontinuities can be sampled and which limitations are inherently introduced in the analysis by the sampling methods being adopted represent important aspects that should drive the collection of discontinuity data for DFN analysis; this will require the introduction of a more appropriate set of guidelines bridging the gap between the current, very practical, ISRM methods and the data requirements imposed by the use of new DFN technologies.INTRODUCTIONThe last decade has seen a major increase in use of the Discrete Fracture Network (DFN) approach, both as a stand-alone tool or integrated within more complex geomechanical simulations (Rogers et al., 2014 and Elmo et al., 2014). In particular, the DFN approach offers the opportunity to maximise the use of fracture data collected from mapping of rock exposures and to construct synthetic rock mass (SRM) models. However, the potential of DFN based modelling is limited if there is insufficient care in collecting the necessary structural data at the required engineering scale. DFN models are also subject to the process of data calibration and validation (Hadjigeorgiou, 2012). With DFN modelling becoming an almost integral part of many geotechnical and mining engineering problems, the authors believe there is an ever greater demand to review the process of collecting fracture data in the specific context of DFN modelling.The value of the DFN model depends directly on the quality and quantity of available field data. For example, fracture length (persistence) is an important parameter in DFN modelling; however, this parameter is either seldom available at the pre-feasibility stage due to a lack of exposures (man-made or natural), or engineers have access to limited length data collected along exploratory drifts. Characterisation of rock exposures should also take into account limits of window/scanline mapping techniques with respect to both trace length bias and the effect of cut-off assumptions inherent in the mapping methodology."

Jan 1, 2015

By M. Cai

"It is well known that Peak Particle Velocity (PPV) plays a critical role in triggering rockburst damage in burst-prone underground mines. To estimate the PPV distribution around excavations, advanced numerical modeling can be used. In wave propagation numerical modeling, velocity field is often assumed to be uniform around an excavation. However, it is observed that wave velocities near mine openings are not constant, but rather non-uniform. Wave velocity in a rock mass depends on many factors such as rock quality and confinement. In particular, confinement has a large influence on wave velocity. The confinement around an excavation is low at the wall boundary and increases gradually and reaches a constant value far away from the excavation boundary. Hence, stress redistribution due to excavation will have a profound influence on wave propagation in underground mines. A better understanding of the influence of excavation effect on wave propagation helps to interpret the field observation of rockburst damage and improve mine safety. For this purpose, a non-uniform velocity model need to be constructed and the influence excavation effect should be taken into account in numerical wave propagation modeling.In the present study, a non-linear velocity model is developed firstly by considering the influence of confinement on wave velocity. This model links wave velocity to confinement explicitly. A coupled numerical method is then developed and used to study the seismic wave pattern around excavations in underground mines. Two codes, FLAC and SPECFEM2D, are coupled in the analysis. The motivation of developing the FLAC/SPECFEM2D coupled approach is to take merit of each code, such as the stress analysis capability in FLAC and the powerful wave propagation analysis capability in SPECFEM2D. The coupling process is realized through three steps: (1) static stress redistribution around an excavation is analyzed in FLAC; (2) data for coupling analysis, such as non-uniform velocity field (based on the new developed velocity model), mesh, absorbing boundaries, etc., are generated by FISH functions in FLAC and passed to SPECFEM2D; and (3) wave propagation modeling is performed in the SPECFEM2D considering a fault-slip seismic source. Because stress redistribution around the excavation is considered, non-uniform velocity field for the SPECFEM2D model can be obtained and this is a notable feature of this study. Very large difference in the S-wave response in these two modeling approaches with uniform and non-uniform velocity fields can be seen from the modeling results.Using the FLAC/SPECFEM2D coupled modeling approach, accurate velocity models can be constructed and this in turn will help to produce accurate PPV distribution around the excavations. Accurate PPV contours can be used to identify high rockburst risk zones for improved dynamic ground support strategy."

Jan 1, 2015

By Hongyan Qu, Lihui Zheng

"Horizontal wells in coal seams, Qinshui basin, China are prone to wellbore instability problems induced by drilling, completion and production operations due to the presence of natural cleat network, anisotropy with regard to permeability, brittleness and mechanically weak property of the coal rock. The mechanism of wellbore instability in coal seams is very different from that in conventional formations, the traditional wellbore stability study methods therefore, are not proper for wellbore stability analysis in coal.In this study, the mechanism and controlling of wellbore stability of coal seams in the Qinshui basin was investigated through theoretical modeling, laboratory experiment and field operation. Firstly, a new physical model of wellbore stability for highly-cleated coalbed was proposed, considering the combined effect of mechanical mechanism and reservoir characteristics, specifically, taking the effect of reservoir pore pressure in the vicinity of the wellbore on the wellbore stability into account. Then experiments on the triaxial stress evaluation were conducted at laboratory where rock mechanical parameters such as Poisson's ratio, Young's modulus, compressive strength, tensile strength, angle of internal friction and cohesion ability were measured respectively. The in situ stress at different depths in four wells of Zheng 1-303, Zheng 1-308, Zheng 1-309, and Zheng 1-310 in the Zhengzhuang were calculated, and the collapse pressure and formation breakdown pressure were predicted through the theoretical model we developed. Finally, by comparing the maximum collapse pressure and minimum breakdown pressure of the four wells in the coal as well as in the roof and floor of the coal seams, the fluid weight window for safe drilling in each coal seams was determined, and appropriate approaches against anti-sloughing in coal seams, Qinshui basin were applied in the field operation.The wellbore stability was found not only related to the wellbore pressure, but also affected by the pressure in the reservoir through the theoretical model. The fluid weight window for safe drilling in each coal seams varies with the coefficient of wellbore stability in the model. The laboratory experiment results indicate that the roof and floor of 3 # coal in Qinshui basin has high breaking strength, high heterogeneity, and are easy to collapse and breakdown. In addition, the whole rock mineral analysis shows that 3 # coal in the Duanshi block has high clay content, resulting in the phenomenon of hydration swelling as clay encountered water, and leading to unstable coal and extreme large drilling uncertainties. Due to the effect of the unstable rock mechanical properties of the roof and floor formation on the wellbore stabilizing, drilling parameters, drilling fluid performance and BHA were optimized during the drilling process according to the formation properties, rock mechanical properties and drilling techniques in the field operation."

Jan 1, 2015

By W. Holyk

"Although lead, zinc, copper, and iron sulphides have been known for many years in the Bathurst region, the existence of large massive deposits was not known until the discovery of the Brunswick orebody in 1952. This was followed by the discoveries of the Anacon orebody in 1953 and the American Metals orebodies in 1954. There is no question as to the great importance of these large massive sulphide deposits, and no doubt that other sulphide deposits are to be found. The problem, of course, is where and how to find them.The discovery of the Brunswick and Anacon orebodies is attributed to geophysical work. The original discovery of the American Metals deposit is generally attributed to a regional airborne electromagnetic survey.It is generally stated that the Bathurst area is a geophysical camp, and this is essentially true, but in this highly competitive search for orebodies it is obviously impossible for an individual company to cover the entire area by a comprehensive geophysical survey. Some means other than geophysics must be used to narrow the target. The quickest, cheapest, and simplest method is geological investigations.It has been stated that nothing can be accomplished by geology in the Bathurst region, since the camp is largely covered with overburden. This is true only insofar as detailed work on certain properties is concerned. It is not true of the larger regional picture. Outcrops are scarce, but angular float is abundant, and precedent shows that angular float has moved but a short distance from its source.GeologyAeromagnetic maps published by the Department of Mines and Technical Surveys are the best guides to the geology and structure of the area. These maps supply factual information concerning the underlying rocks. When coupled with field investigations, they are very useful in the interpretation of regional geology and the selection of favourable areas. The discussion of the geology is accordingly centred upon the aeromagnetic maps. The following is essentially a working theory, based on geological facts as best reconciled with all other available information,"

Jan 1, 1949

By Troy Boisjoli, Sean Hillacre, Matt Batty

Discovered in 2014, the Arrow Uranium Deposit has undergone rapid development through successive drilling programs informed by geostatistical drill hole spacing studies. An independent third-party geostatistical drill hole spacing study was completed by Clayton V. Deutsch Consultants Inc. in 2017, evaluating the uncertainty of thickness, grade, density, and areal limit of the Arrow Deposit to determine a drill hole spacing suitable for Indicated Mineral Resources. Indicated spacing was defined to be 24 to 32 metres (“m”) to be within 15% of predicted for a nominal quarterly production volume with a probabilistic tolerance between 75 and 90%. The study not only defined the Indicated Mineral Resource resultant from the 2016 drill program, but also provided drill hole targeting criteria for subsequent drill programs aiming to convert Inferred to Indicated Mineral Resources. A subsequent geostatistical drill hole spacing study on the Arrow Deposit was completed by Clayton V. Deutsch with Resource Modeling Solutions in December 2018 to define Measured Mineral Resource spacing in support of the 2019 drill campaign. The study resulted in a drill hole spacing of 9 to 17 m to be within 15% of predicted for monthly and quarterly production volumes using an accepted industry probabilistic tolerance of 90%.

Jan 1, 2020

By J. E. Quinn, S. Wolstencrof, K. H. Soldenhoff

Ion Exchange (IX) using Strong Base Anion Exchange (SBA) resins is conventionally used to purify uranium from sulfuric acid pregnant leach solutions (PLS), particularly when uranium grades are relatively low. However, the presence of chloride in the PLS interferes negatively with conventional SBA based IX processes, by reducing the uranium loading on the resin. Chloride can be present in the PLS due to the use of saline bore or seawater in leaching, or chloride containing leach/IX reagents. ANSTO has been examining strategies to combat this problem for several years. ANSTO previously reported that a recently developed high-capacity SBA resin was capable of extracting uranium efficiently from saline leach liquors produced at Boss Resources’ Honeymoon in-situ recovery mine in South Australia. The resin was tested successfully in a 2017 Field Leach Trial carried out onsite in the existing wellfield area. While the piloting was extremely promising, the elution was more challenging, with eluate tenors limited to 2 g/L U3O8 using NaCl. This is due to the resin’s strong affinity for the uranium complex, which makes it difficult to elute efficiently by standard methods. In this paper, we describe a novel elution process developed for strong base resins that significantly improves upon conventional methods. The process, developed by ANSTO, is based upon conversion of the extracted uranyl sulfate species to uranyl carbonate, followed by elution with sodium chloride. The loading and elution process was demonstrated in continuous locked-cycle piloting conducted at ANSTO in 2019. The results were excellent, with eluate tenors of 8–9 g/L U3O8 achieved from Honeymoon PLS containing 50 mg/L U3O8, with very little transfer of impurities. In subsequent test work, the eluate was shown to be amenable to uranium peroxide precipitation. The results represent a huge step forward for the purification of uranium from saline leach liquors.

Jan 1, 2020