Search Documents

By Ian S. Leslie

Seismic monitoring systems for mining operations are being utilized more than ever before in the characterization of rock mass response to underground and open pit mining. This paper provides a review of the use of microseismic monitoring for rock mechanics applications at mines throughout the world. Some practical considerations for the installation of these systems are presented along with techniques for optimizing seismic array coverage. Case studies and installation examples are also provided. Recent applications of advanced seismic analysis techniques are discussed including the determination of event mechanisms, mapping of maximum peak particle velocity (PPV) and seismic hazard fields, and the use of source parameter data for large event re-entry protocol.

Jun 1, 2012

By C. Zangerl, W. Fellin, M. Holzmann, B. Hofer, S. Perzlmaier

"Four deep-seated rockslide systems were investigated and are under surveillance by TIWAG (Tyrolean hydro-electric Company) since the mid-1960s after impoundment of Gepatsch reservoir began. These rockslide systems consist of several individual sliding masses (slabs) which show variable activity from zero to a few centimetres per year. The focus in this paper will be on the findings for the transient deformation behaviour of the Hochmais slab which is part of the “Hochmais-Atemkopf” rockslide system.The rock mass has slid over moraine deposits in the last post-glacial period and was in equilibrium (or slow to extremely slow moving, respectively) until the filling of the reservoir began. During the initial reservoir filling in summer 1964 considerable movements had been observed over a length of 1000 m accompanied with an activation of the Hochmais slab. Geological investigations, additional surface and subsurface measurement showed that the sliding mass is characterized by an en bloc movement and the deformation accumulates within a several metre thick shear zone located within the moraine. In contrast to the deformation characteristics for the first impoundment process (1964 – 1966) where the magnitude of deformation occurred during impoundment, the maximum amount of deformation since 1967 occurs during the drawdown of the reservoir. Based on long term measurement it can be shown that the magnitude of deformations per year correlates with the minimum storage level in the reservoir. Other external influences such as precipitation and snowmelt have no observable impact on the deformation characteristic of the landslide. On the basis of long-term data series it was possible to determine the factors of influence and to elaborate a conceptual mechanical model which describes the transient deformation behaviour of the Hochmais slab induced by the drawdown of the reservoir. The mechanical model considers the reduction of uplift forces in the highly fractured and permeable rock slab during drawdown as well as increasing seepage forces in the less permeable moraine material."

Jan 1, 2015

By D. M. Ward

"The uranium deposits upon which the Rabbit Lake project story is based are located at the eastern margin of the Athabasca Basin just west of Wollaston Lake in northern Saskatchewan. This paper provides a general review of the exploration history for the major deposits and the influence of an expanding geological data base, which served to guide the continuing exploration programs.A brief description of each of the deposits is provided in order of their discovery and with emphasis upon their relative geological and mineralogical characteristics.The Rabbit Lake and Eagle Point orebodies are monometallic uranium deposits localized by thrust faults within the Aphebian Wollaston Group. The Cof/ins Bay A-zone, B-zone, and D-zone are polymetaflic U, Ni, As, Co (Au , Ag) deposits located within the Helikian Athabasca Group at its unconformable contact with the underlying Wollaston Group. INTRODUCTIONThis paper demonstrates the importance of applying the accumulated geological knowledge, gained through the exploration, mining, and development process, to the ongoing success of exploration programs. To emphasize this point, the basic geology of each of the major Rabbit Lake area deposits will be presented in chronological order of their discovery and subsequent development. These depos its include Rabbit Lake, Collins Bay A-zone, B-zone, D-zone and Eagle Point. The geological descriptions are based primarily upon the detailed observations of many current and former geologist s employed by both Gulf Minerals Canada Limited and Eldorado Resources Limited. Much of the early historical data was obtained from Dr. E.E.N. Smith, formerly with Eldorado Resources Limited. Regional GeologyThe Rabbit Lake area which includes the Rabbit Lake, Collins Bay A-zone, B-zone, D-zone and Eagle Point deposit s, is located on the eastern edge of the Athabasca Basin close to the western shores of Wollaston Lake (Fig. I). The area is in the Churchill Province of the Canadian Shield within the Wollaston lithostructural domain, at the eastern edge of the Athabasca Group. The uranium deposits occur within both the Wollaston Group metasedimentary assemblage of probable early Aphebian age, and the diagenetic ally altered quartz sandstones and conglomerates of the Athabasca Group of Paleohelikian age. Both units unconformably overlie granitoid gneisses interlayered with metasediments and a graphitic iron formation all believed to be of Archean age. All uranium depo sits in the Rabbit Lake area occur in close proximity to the Paleohelikian - Aphebian or Paleohelikian - Archean unconformity."

Jan 1, 1989

By G. P. Gu

The in-service 90/10 cupro-nickel tubes in a water-chiller system suffered from severe corrosion damage during their relatively short service life causing unexpected down time. In addition to downtime, the environmental risk associated with losing refrigerant was also a concern that initiated this investigation, Microstructural investigation using SEM and electron microprobe indicated that pitting corrosion had resulted in local nickel depletion, During the corrosion process, copper appeared to have re-deposited around the corrosion pits accelerating the local corrosion.

Jan 1, 2005

By V. Chatain

The environmental assessment of historical mining sites contaminated with various inorganic species, as also the determination of remediation targets require a better knowledge of pollutant-bearing phases. The objective of this paper was to investigate the operational fractionation of arsenic (As) in an As contaminated (ca. 3 wt%) soil collected from a gold mining site in France, where mining activities and smelting processes of gold ores took place until 2004. Single and sequential chemical extraction procedures were performed to evaluate the potential mobility of As according to the fractions to which it was associated in the contaminated soil, and also the part of As sorbed onto soil particles. These procedures used provided information on the nature of As fixation processes in the mining soil studied. Results showed that As appeared mainly sorbed (ca. 72%) with iron on the soil particles, in particular amorphous iron oxyhydroxides. These results confirmed a potential risk of arsenic mobilization under acidic and/or reducing conditions, which frequently occur in mining environment. This research evidenced the importance of the knowledge of As-bearing phases to better predict the mobility of this pollutant and in turn improve the management of As contaminated sites.

Aug 1, 2013

By M. B. Greyver

The results of laboratory tests on iron precipitation from non-decopperized nickel anolyte are discussed. The parameters (pH, oxygen consumption and stirring speed) for iron precipitation from the anolyte, using the oxygen in the air, were determined. In the experiments conducted under optimized conditions, the residual concentration of iron in the anolyte after precipitation was 0.7-2.7 mg/L, and the copper and nickel losses to the solid phase were 0.05-0.07% and 0.05-0.16%, respectively. The filtration ability of the iron slurry obtained was 2 to 5 times higher as compared to that after chlorine oxidation and oxyhydrolysis. The leaching of the non-ferrous metals from the iron cake made using the separate nickel anolyte purification process was possible by dissolution in sulphuric acid. It was established that after cobalt precipitation from the copper- and iron-depleted anolyte, the precipitates obtained had lower ratios of Fe:Co and Ni:Co.

Jan 1, 2006

By Holly L. O. Huyck

Disseminated hypogene sulphide mineralization in the Lakeshore porphyry copper deposit (also called the Cyprus-Casa Grande deposit) of Arizona occurs in both a granodiorite stock and associated volcanic rocks. Structural development and vein paragenesis at Lakeshore are similar to other Laramide porphyry copper deposits of the southwestern U.S. Two major structural trends are present: intrusive contacts, copper-bearing potassic alteration veins and major post-mineralization Basin-and-Range type faults trend N-NW, whereas phyllic veins and secondary post-mineralization faults trend N-NE, and deep propylitic veins trend NE-ENE. Lithologic permeabilities, caused by fracturing in all rocks and by grain size distributions in volcanic rocks, controlled the distribution of copper mineralization. Differences in chemical compositions of host rocks did not affect are grade. Structural control, through density of chalcopyrite-rich veins, was the major control of are grade. Fracture density of other potassic vein types did not strongly affect grade. Within volcanic lithologies, permeability, as indicated by grain size distribution, provided a second-order, but significant, control of mineralization.

Jan 1, 1990

By E. Busse, J. E. Burgener, J. G. Eacott, M. C. Robinson, P. E. Burgener

"This paper presents a preliminary assessment of the technical and economic feasibility of a caustic leach - electrowinning process for the recovery of zinc and lead from electric arc furnace baghouse dust at a mini-steelplant. Recent studies and literature are referenced briefly as they pertain to the formation and characterization of dust, toxicity considerations and alternative dust treatment and disposal options.Laboratory testwork results, published data, pilot plant experience and anticipated influences resulting from recycling residues are used for the purpose of developing a conceptual design for a caustic leach - electrowinning plant to treat 15,000 tonnes/year of dust at a one million tonnes /year capacity steelplant in Canada.Target economic studies, comprising preliminary estimates of capital and operating costs, revenues and rate of return are presented. Economic and commercial considerations concerning the relative merits of dust treatment at a centralized facility compared with an on-site plant are discussed.IntroductionThe treatment or disposal of mini-steelplant electric arc furnace (EAF) baghouse dust has been given increasing attention in recent years for two principal reasons. Firstly, the dust is now classed as a hazardous waste material under V.S. EPA regulations which prohibit its disposal in dumps other than controlled landfill sites. Secondly, the dust contains certain metal values, notably zinc and lead, which may be economically recoverable, depending on the costs associated with disposal resulting from enforcement of the EPA regulations. Other metallurgical dusts and waste materials, from both ferrous and non-ferrous operations, may require the same considerations as EAF baghouse dust.Several studies have been carried out to examine various aspects of dust treatment but few commercial plants are in operation. Technology employed uses pyrometallurgical techniques. Commercial-scale hydrometallurgical plants are not known to exist although small-scale plants are frequently more economically attractive than their pyrometallurgical counterparts which generally require economies of scale to be viable.The concentration of mini-steelplants in northeast V.S.A. and southeast Canada merits study to determine whether or not dust treatment for metals recovery is a commercially feasible alternative to disposal.This paper examines the technical and economic feasibility of a caustic leach - electrowinning process for the recovery of zinc and lead from EAF baghouse dust at an on-site ministeel plant processing carbon steel scrap and discusses economic and commercial considerations pertaining to dust treatment at a larger, centralized facility."

Jan 1, 1984

By L Mariani, G. Mendoza-Suarez

In this investigation, TiH2 powders were coated with copper and nickel by electroless plating to delay hydrogen evolution. Copper-coated samples were found to have a mixed acicular (2D growth) and cauliflower (3D growth) morphology whereas the nickel-coated samples had a cauliflower morphology. Examinations of the coated powder cross-sections revealed that the coating thickness ranges from 0.2 µm to 4 µm. Uncoated areas on the powder surface and coating flakes unattached to TiH2 particles suggest poor adhesion between the coating and the substrate. The phase transformation undergone by the TiH2 during dehydrogenation was studied in samples taken at intermediary points in the heating cycles and examined by XRD. The findings reveal that as the powder is heated from room temperature to 800°C, it changes from TiH1.971 to Tiu and to aTi. Differential Thermal Analysis (DTA) was performed to study the effects of the coatings on the temperature of hydrogen release. It was found that increasing the number of plating iterations, and therefore the thickness of the coating, creates a significant shift in the temperature of gas release.

Jan 1, 2006

By T. Gerritsen, C. Martinez, F. Stober, T Ma, J. R. Frias, M. Sedighy, J. Janzen

Electrode control systems regulate power by physically positioning electrodes. Due to the weight and inertia of the electrodes and hoist equipment, this is a relatively slow process where power fluctuations of less than a few seconds are not fully corrected. Nickel laterite AC furnaces operating in high voltage, shielded arc mode typically incur frequent power variations of approximately +/- 20% or more around the power set point. To provide enhanced power control, Hatch has recently supplied, at commercial scale, a thyristor-switched reactance system called an SPLC. The SPLC incorporates predictive control software to operate furnaces at the maximum transformer rating by reducing the large power swings experienced without the SPLC. The resulting higher average power enables higher production, without increasing transformer or power plant capacity. A 60 MW production version of the SPLC has been commissioned on Falconbridge Dominicana's laterite nickel furnace, yielding excellent results with a 3 to 1 reduction in power fluctuations.

Jan 1, 2005

By Sophia Wong

Nickel is used in a wide variety of applications from consumer goods to industrial uses. In many of these uses, nickel contributes to the environmental attributes of the product. The challenge, however, is measuring that contribution, comparing it to the environmental cost of production, and communicating the role of nickel to the customer in a way that is easy to understand. This paper presents the Nickel Institute?s approach to climate change as a global commodity industry association, and discusses where we stand with regard to some of these key questions. It also identifies issues for the nickel industry moving forward ? challenges that are likely to be common to other commodities.

May 1, 2009

By J. J. Brummer

"A reconnaissance geochemical survey, using the stream sediment technique, is described. The survey covered an area of about 400 square miles, in the Seal Lake area of central Labrador, underlain by basaltic flows, diabase and metadiabase sills, and sedimentary rocks. Previous work had indicated numerous small copper occurrences within the Seal Lake group of rocks. Stream sediments were tested for the readily extractable copper content and total heavy metal content. The results of the copper survey did not yield any new data on the distribution of copper mineralization. Results of the total heavy metal survey attracted attention to a remote portion of the area (Ten Mile Lake), which had hitherto been regarded as having no economic interest. The anomalous values found, suggested that zinc mineralization should occur in this region. Geological mapping indicated that the rocks exposed belonged to the Letitia Lake Group, which is older than the Seal Lake Group exposed to the east, which contains the copper mineralization of the district.Investigation of the area lead to the discovery of: (1) uneconomic lead-zinc mineralization; (2) radioactivity extending over a considerable area. Evaluation of the radioactive rocks led to the discovery of columbium-thorium mineralization in amphibolite and in diopside-actinolite schists along a contact with intrusive alkali syenite.Thus a geochemical survey, which was planned to evaluate a copper province, resulted in the discovery of lead-zinc-columbium-thorium mineralization."

Jan 1, 1960

By G. P. Demopoulos

The solubilities of calcium sulfate in HCl-CaC1z-H20 solutions up to 100°C were successfully modelled with the aid of OLI software after bringing proper modification to it. Modelling, more specifically, was carried out with the help of the Environmental Simulation Program, V-6.6.0.4 (www.olisystems.com). New model parameters were obtained by regressing the solubility data. A private databank was established by adding the newly defined model parameters and the calcium sulfate hemihydrate phase that is not included in the original OLI database. The McGill-modified OLI software was successfully applied not only to modelling solubilities but also the transformation of the various CaS04 phases, namely dihydrate, hemihydrate and anhydrite. In this paper, the modelling methodology will be discussed along with a comparison of the capabilities of the newly developed model vs the original OLI model.

Jan 1, 2005

By W. A. Dixon Edwards

Gravel deposi ts in the Edmonton region are unique in their diversity in origin and age. The deposits were described first around the turn of the century (Dawson and McConnell 1896) . Among the many more recent in vestigations are works by Rutherford (1936), Shelley and Associates Limited ( 1977) and the City of Edmonton (1978) .

Jan 1, 1984

By J. Stiksma, R. Kalanchey, M. J. Collins, G. Owusu, R. Raudsepp, K. R. Buban, L. A. Barta, L. Masters

This paper describes the results of testwork for the treatment of Ambatovy laterite by an acid pressure leach process, with recovery of the soluble nickel and cobalt values as mixed sulphide intermediate by precipitation with hydrogen sulphide, and subsequent refining of the mixed sulphide to nickel and cobalt metals. These process development studies were carried out primarily in 2004, as part of a bankable feasibility study for the Ambatovy Nickel Project.

Jan 1, 2004

By R. del Villar, A. R. Laplante

"This article presents four grinding simulation programs, written in Applesoft BASIC. The firs t two calculate residence time distributions (RT Ds) for open and closed loops mills. The third program calculates the select ion functions from the RTD, breakage function and particle size distribution (PSD) o f the feed and discharge. Two linear regression programs are also included to calculate the breakage function. These results are used in the fourth program to simulate continuous or batch grinding kinetics.The modelling approach presented is the size discrete, time continuous matrix formulation presented by Reid (1965) from concepts originally proposed by Epstein (1948). It is at the present time the most widely accepted phenomenological model of grinding kinetics and is standard textbook material (Austin et 01., 1982; Kelly and Spottiswood, 1982, p. 152). The concepts of RTDs and tracer testing originated from chemical engineering theory and practice, and are well presented in Leven spiel (2n d Ed . 1972 , Ch. 9) .Applesoft* was chosen because it is compatible with many micro computers. It is also one of the simplest and least powerful BASIC versions. Thus it can easily be adapted to other more complex BASIC versions.Open Loop Residence Time Distributions (Program RTDOPEN)As mixing, channelling, stagnation and short-circuiting all affect slurry motion in tumbling mills, transport characteristics are very complex an d cannot be derived from fundamental principles. Fortunately , as grinding follows first order kinetics, transport characteristics for the purpose of grinding simulation ca n be represented by the RTD of the slurry phase . It is normally determined using liquid tracers, as it has been demonstrated and is commonly accepted that in industrial ball mill s, the RTD of the so lid phase is particle size independent and equal to that of the liquid phase."

Jan 1, 1985

By J. W. Matousek

Since the late 1800s, copper-nickel ores have been mined and smelted in the Sudbury area. The Canadian Copper Company, the Copper Cliff ancestor of Inco Limited, commenced operations with a blast furnace smelter in 1888. Coal-fired reverberatory furnaces were added in 1911 and multihearth roasters in 1914. The blast and reverberatory furnaces smelted, respectively, coppernickel ores and ore fines until 1930, when a milling process and plant began operating to concentrate and separate the minerals of these two metals. Two reasons for this delay were: (1) the availability of high grade ores suitable for direct smelting; and (2) the difficulties in making the copper-nickel separation. The Mond Nickel Company, however, practiced flotation at its Coniston Smelter site from 1914 to 1930. A bulk concentrate containing six per cent copper and five per cent nickel was recovered from ore of 1.6 per cent each of copper and nickel. Gravity (table) and magnetic concentrates were also produced. Inco Limited (then The International Nickel Company) began laboratory-scale flotation tests on its ores in 1918. This work led, ultimately (in 1930), to the construction of the 7500 tonne-per-day Copper Cliff Mill, designed to recover separate copper and nickel concentrates. Its capacity was expanded to 11000 tpd in 1936, to 18 000 in 1940, and to 27 000 in 1942. Since 1971 it has operated to process only the bulk flotation products from other mills to yield individual nickel and copper concentrates.

Jan 1, 1999

By Theophile Yameogo

The rock mechanics literature has documented the challenges, failures and successes of tunneling through weak rocks. Cases usually deal with low RMR rock masses or high stresses in a fractured zone. With the combination of 5MPa water pressure, 14 RMR ground with clay infillings and ground freeze walls, the case of the 510-8225N development drift at McArthur River is certainly much more challenging, especially when high grade uranium production is at stake. The article explains the excavation and the ground control techniques that were used to overcome the challenges of development at the Unconformity in the Athabasca Basin.

Aug 1, 2010

By Pierre Antoine Dhaiti, Gilbert Sergerie, Michel Dagbert, Jean-Maurice Brodeur

"Quality of iron ore is generally determined by several factors which can be correlated or independent. Among these f actors, we generally find per cent iron, silica, magnetite or hardness. Forecasting the short- and long-term fluctuations of these f actors in the future pit is an important feature of mine planning in these deposits. Computer simulation provides a realistic answer to these questions. It allows to generate values for the most important quality features of each shovel load with the proper correlations between them as well as between one load and the next being fully reproduced. Then different sampling schemes f or grade control or blending facilities can be examined on the simulated data. The mechanics of the simulation procedure and its potential applications are described in an example.IntroductionThe purpose of this paper is to illustrate the use of in-situ grade simulation in the planning o f the grade control in an iron ore min e. More precisely, given a production unit of given size, we need to know how many samples have to be collected in that unit so that we ca n recognize its grade with a reasonable precision. Conclusions that we would like to arrive at are of the type: with 4 blasthole samples we ca n get the iron grade of a 10,000 ton bloc k with less than a ± 2% Fe error 95% of the time.The approach t hat we take to solve this problem is simulation. We simulate the grade of samples and the grade of the block that contains these samples. We repeat the simulation for hundred s o f blocks. By comparing the sample grade with the block grade in each case, we determine the actual number o f blocks where the difference sample-bloc k is less than a given limit."

Jan 1, 1983

By Isabel F. Barton, Matthew J. Gabriel, Mark D. Barton

Process control, mine-to-mill optimization, and other mining operations depend on having robust, comprehensive mineralogical and chemical characterization. However, current characterization methods rely primarily on analyzing samples from trenches, channels, blast holes, and drill holes and interpolating between them, and are not always sensitive to some minerals (such as clays) that cause major problems for mining and mineral processing. Continuous characterization is possible with techniques such as hyperspectral remote sensing, which measures reflectance or absorption of light in the visible to near infrared (VNIR) and short-wave infrared (SWIR) regions of the electromagnetic spectrum. Absorption and reflectance features are characteristic of different chemical bond types, so each spectrum corresponds to a different mineral or material. In remote sensing, each pixel in the scanned area has both a location and a spectrum. This makes hyperspectral remote sensing potentially useful for characterizing mine site materials. In this study, we tested a hyperspectral remote sensing system as a method of characterizing the mineralogy and material types at mine and metallurgical sites. Our test site was a small open-pit copper mine and leach operation in the southwestern U.S. We scanned mine highwalls, dump piles, leach pads, and nearby rock outcrops with drone- and tripod-mounted VNIR-SWIR spectrometers. We collected ground-truth data through geologic mapping, sampling, and spot analyses with a portable short-wave SWIR instrument. The results show that the hyperspectral remote sensing system that we tested is capable of distinguishing the types and distribution of spectrally active minerals and other materials in diverse mining settings, including showing wet and dry areas of leach pads; clay and carbonate type and distribution on mine highwalls, leach pads, dumps, and rock outcrops; plant type and distribution; fault zones, bedding planes, and other geological features; and qualitative spectral matches between dump piles and areas of the mine highwalls. Hyperspectral sensing proved particularly sensitive to the presence and type of clay and carbonate minerals, which cause geotechnical and metallurgical problems such as highwall failure, gangue acid consumption, and flotation sliming. Examples will be presented and discussed at the conference. Areas of continuing research include automating and streamlining the data reduction process, integrating hyperspectral data with block modeling and mine planning software, and testing the results of hyperspectral sensing in different geological environments.

Jan 1, 2019