Search Documents

By F. Chiesa

Experimental results on thin and thick castings poured in aluminum A356 and magnesium AZ91E by the low pressure permanent mold process have been compared to the result of filling simulations for thin and thick castings. If the results of modeling is reliable when the liquid remains above the liquidus temperature, this is no longer the case when partial solidification occurs. The visco-elastic behavior of a partially solidified liquid is difficult to put into equation as it depends on the amount of shear it has been been subjected to. Attempts to predict misruns with a commercial software has been proven to be very difficult if not impossible; divergence of the numerical solution has been observed unless prohibitively long computing times are used. In order to overcome these difficulties from a practical standpoint, a simple method is proposed which consists in tracking the temperature of the advancing liquid metal front so as to make sure it will always be above so-called `Misrun Critical Temperature' (MCT) determined experimentally for thin and thick aluminum A356 and magnesium AZ91E castings. If the liquid metal front falls below this temperature, a cold-shut or misrun is likely to happen at this location. The values of MCT for thin and thick in aluminum A356 and magnesium AZ91E were determined experimentally on misrun castings of extreme geometries (a thin 2.5 mm wall cover and a 6mm to 25 mm thick bell housing). MCT was found to be lower for magnesium AZ91E and for the thicker castings.

Jan 1, 2011

By F. Pinto, C. A. Prato, R. J. Rocca, P. F. J. Huerta Soaje

"The seismic hazard for civil engineering structures is generally defined in terms of deterministic or probabilistic acceleration response spectra at an equivalent rock outcropping. The design of tunnels, however, requires the definition of demands in terms of accelerations at ground surface (near the portals) and in terms of both accelerations and velocities at different depths within the alignment. The design near the portals is controlled by inertial effects and is often times impacted by the possibility of slope instability and rockfall, whereas the design at deep sections is controlled by kinematic effects. These effects are accounted for in practice by introducing deformation patterns in the structure that are related to an assumed wavefield, often times ignoring the effect of the structural stiffness in the response. This paper presents a study regarding the definition of seismic demands for different sections of 14-km long tunnel in the Andes (Argentina-Chile), with a maximum overburden of 1750 m in a seismically active region. The tunnel will pass through volcanic massifs mainly composed by andesites and rhyolites.The study includes the definition of spectrum-compatible seismograms, deconvolution, and definition of accelerations and peak particle velocities for different overburden conditions. A kinematic interaction study for a 500-m tall ventilation chimney shaft is also described, where a simple formulation for the interaction analysis is considered in order to more accurately evaluate shear and bending demands. INTRODUCTIONThe seismic design of linear underground structures, such as shafts and tunnels, generally considers the inertial forces near the shallow sectors (e.g., portals) and the kinematically imposed deformations for the deep sections (e.g., Hashash et al. 2001). The inertial forces are often times evaluated on the basis of design spectra recommended by seismic hazard studies. The kinematic demands for the deeper sections, however, needs to be defined in terms of additional information which is not always indicated by the seismic hazard studies, e.g.; peak particle velocities and accelerations, and their variation with depth. These parameters can be determined by means of a site response analysis, whereby outcrop motions can be deconvoluted in order to evaluate motions inside the ground mass (e.g., Schnabel et al., 1972). Hashash et al. (2001) defines factors that may be used in order to account for attenuation of motions inside the ground mass. However, these factors are provided for depths up to 30 m only, whereas depths of tunnels structures can range up to thousands of meters."

Jan 1, 2015

By Samuel Frimpong

Green house gases have become a major concern within the international community over the last two decades due to their potential link to global warming. Carbon dioxide (CO2) is the principal greenhouse gas. In the Kyoto Agreement, Canada has committed to reduce emissions by 6 % below 1990 levels by 2012. This presents a serious economic challenge to Canada and Alberta. Over the next decade, oil sands production expansion, population and industry growth and energy demand will increase CO2 emissions. Current and future CO2 emissions and their economic implications in Alberta will be critical in formulating a comprehensive and balanced policy for dealing with concerns in this area. Disposal of carbon dioxide (CO2) in land aquifers is a potentially viable option for Alberta in dealing with long-term CO2 emissions. Studies have confirmed the existence of appropriate aquifers in the Alberta Basin for CO2 storage over a long geological period. Carbon dioxide is an ideal candidate for aquifer disposal because of its high density and solubility in water at relatively high pressures. In this study, the authors develop a computer simulation model of a scaled aquifer disposal system. The scaled model consists of an injector well, aquifer environment with dominant Ca++ and Mg++ cations. Liquefied CO2 is injected at an appropriate pressure and concentration through an injector well model. The injected CO2 migrates from the point of contact between the injector well and the aquifer domain to the main regime of the latter. The rate of migration is a function of porosity, permeability, cations, aquifer fluid flow regime and CO2 injected pressure. These models are validated using flue gas data from the 546 MW Wabamum Power Plant in Alberta. The total energy requirements for aquifer CO2 disposal system are distributed between a minimum of 105 MW and a maximum of 172 MW, with a mean of 132 MW and a coefficient of variation of 10%. The results show that there is significant variability in all the energy requirements for the CO2 disposal system. The total energy requirements for the disposal system as a fraction of the total power generated by the Wabamum plant of 546 MW could be between 0.19 and 0.32. This is a very significant energy requirement and thorough analysis must be carried out to reduce this variability and energy requirements.

May 1, 2001

By P. J. Foster

Bowtie analysis has recently emerged as a technique of choice that can be used when looking specifically at major hazards in the mining industry. A Bowtie diagram is a graphical means of assessment that focuses on identifying all the specific causes and consequences of major events, from which all the ?pre-event? and ?post-event? control measures can be identified. From this critical control measures can be identified and monitoring/assurance systems can be established. It is this assessment of control measures and their effectiveness that replaces the more traditional evaluation of risk (using matrix-based approaches) based on the fact that risk is a function of control ineffectiveness. This is a major difference with traditional risk assessment where all too often control effectiveness is assumed. This paper summarises the Bowtie analysis process and outlines one specific case study where the technique was used on the unwanted event of a collision of a haul truck and light vehicle in an openpit mine. Although more effort is required in undertaking the assessments, control assurance provided this way will go a long way in ensuring that risk assessments and major hazard management become much more effective in practice.

Aug 1, 2013

By Kazutoshi Haga, Ariunbolor Narankhuu, Ariuntuya Battsengel, Yasushi Watanabe, Altansukh Batnasan, Akita University

"Rare earth minerals are usually concentrated by flotation, magnetic or gravity separation methods to produce concentrates that are subsequently leached with hydrochloric (HCl), sulfuric acid (H2SO4) or nitric acid (HNO3). About 75 % REEs are lost in gypsum by-product when apatite is dissolved in H2SO4, whereas more than 80% of REE can be extracted from the apatite using HCl and HNO3 leaching processes, respectively. Therefore, the main aim of this study was to find an efficient process of dissolution of rare earth elements (REEs) from apatite ore by sulfuric acid solution due to its lower cost. In order to optimize the dissolution process, effects of different parameters, namely, concentration of H2SO4 (0.05 – 6 M), solid/liquid phase ratio (1:50 – 1:100), temperature (20 – 80 ºC), agitation speed (300 – 900 rpm), and leaching time (0.5 - 6 h) on the dissolution of REEs from apatite ore were examined in various intervals. The contents of main REEs in the apatite ore used in this study were (as % wt): 3 % La, 6 % Ce, 0.6 % Pr, 2.1 % Nd, 0.2 % Sm and 0.3 % Y. X-ray diffraction (XRD) analysis identified fluorapatite and phlogopite as main minerals in the ore. The results obtained from leaching experiments showed that more than 85% of REEs were dissolved from the apatite ore under the optimized conditions, which were: 1 M H2SO4, particle size of -150 + 100 µm, S:L phase ratio of 1:50, agitation speed of 500 rpm at 20 ºC for 1h. The XRD analysis revealed that main mineral compositions of the residues from 1M and 6 M H2SO4 leaching are gypsum (CaSO42H2O) and hemigypsum (CaSO40.5H2O), respectively.INTRODUCTIONThe term rare earth elements (REEs) denote the group of 17 chemically similar metallic elements consisting of the 15 lanthanides, plus yttrium (Y) and scandium (Sc) in the periodic table. These metallic elements are generally divided into two sub-groups; (1) the cerium sub-group, which is called “light rare earth elements” (LREEs), includes the elements from lanthanum (La) to europium (Eu), and (2) the yttrium (Y) sub-group elements, which are known as “heavy rare earth elements” (HREEs), are the remaining lanthanides from gadolinium (Gd) to lutetium (Lu) plus yttrium (Gupta and Krishnamurthy, 2005). The REEs occur together in the minerals due to their chemical and physical similarities, which cause problems of separating them from one another (Abreu and Morais, 2014). Although REEs are relatively abundant in the earth’s crust, they are typically dispersed and rarely occur in concentrated forms, making them economically challenging to obtain. There are a wide variety of rare earth minerals, however economic deposits of REEs in mining are bastnasite (La, Ce) FCO3, monazite (Ce, La, Y, Th) PO4, and xenotime YPO4 (Binnemans, 2013; Xie, et al, 2014). Due to the unique physical, chemical, catalytic, electrical, magnetic and optical properties of REEs, demand of these elements has increased dramatically with the advent of new technologies in electronics, communication, construction, energy and medicine (Jordens, et al, 2013). Since 1990, China has provided about 90 % of REEs worldwide. Japan and United States are the largest consumers of China’s REEs. In 2010, China announced to reduce REEs exports to Japan, as it tended to increase prices of REEs and to reduce a stable supply of REEs in the world market (Humphries, 2013). Therefore, there has been an increase in recent exploration activities intended to reveal new commercial sources of REEs and to bring them into production (Antico, et al, 1996). Apatite is an important host mineral for REEs in igneous and metamorphic rocks and can be used as an ore for those metals (Kanazawa and Kamitani, 2006). Apatite is also the main source of phosphate fertilizers and phosphoric acid (Habashi, 2013; Emsbo, 2015)."

Jan 1, 2016

By Ming’an Wei, Qifu Duan, Jianmin Wu, Lusheng Zhou, HMR Group Limited / HMR Technology Canada Ltd., Wenjian Wu

"The development and industrial applications of magnetic liners have been around for decades. A Swedish company Skega first introduced rubber magnetic liners, and then followed by the Chinese invention of metal magnetic liners. Traditionally, both liners were used in secondary ball mills and regrind ball mills for industrial applications, especially for ores containing magnetic materials. Mostly steel balls or equivalent forged steel balls, usually below 60 mm in diameter, were used as grinding media. With the development of mineral resources over the years, SAG mills and larger ball mills have become the dominating components for comminution circuit design. Due to the development of larger diameter ball mills and thus larger ball charge diameter (up to 80mm) especially in non-ferrous metal mining operations, the application of magnetic liners have been very limited. Based on “Magnetism theory” and the development of new materials, the HMR Group Limited has been conducting researches on examining the structures of magnetic liners, associated materials and magnetic circuits which led to the invention of the Nano Alloy Steel Magnetic Liner (NSML). Recently, NSML had a successful application in a 5.5 m diameter × 6.5 m ball mill at the Erdenet Copper Mine in Mongolia. The NSML successfully handled a ball size up of to 80 mm, while achieving a service life of nearly 24 months, which is almost 3 times wear life of the original manganese steel liners.INTRODUCTIONDuring the development and utilization of mineral resources, mineral processing is an indispensably operation. The effective separation of various useful minerals depends on sufficient monomer dissociation of minerals in the ores. The crushing and grinding operation is prior operation of mineral processing. Ball mills are used in different concentrators. As the main consumption parts of mill, liners have been studied constantly. As a new kind of liners, magnetic liners besides can meet the requirement of production, and also have characteristics with maintenance-free, saving energy and increasing efficiency. So the magnetic liners are worth to be spread and applied world widely."

Jan 1, 2016

Mirador - Overview ? Located in Andean foothills of SE Ecuador ? Copper-gold porphyry hosted by calc-alkaline Late Jurassic granitic and porphyritic rocks ? 438 MT of 0.61% Cu and 0.19 g/t Au measured and indicated resources (at 0.4% Cu cut-off) ? Additional inferred resources of 235 MT of 0.52% Cu and 0.17 g/t Au ? Initial 25,000 tonnes/day production, expanding to 50,000 in year 6 320 MT of 0.62% Cu, 0.2 g/t Au ore mined at an average 1.4:1 strip ratio over a 21 year mine-life

May 1, 2006

By J. J. Quinn

Several mineral flotation plants utilize process water with high soluble salt content. The processing of semi-soluble minerals, the use of recycle streams, sea or well water give rise to this situation. It is unclear as to the overall effect on flotation response though there does seem to be evidence of bubble size reduction, increased froth stability and reduced reagent dosage. The present work aims to quantify the effects of salts present in process water on gas dispersion (bubble size and gas holdup) and froth properties. The salts examined were NaCI, CaCl2, Na2SO4, Na2S2O3 and Al2(SO4)3. Tests were conducted to determine the effects of salt type and concentration on gas holdup and bubble size distribution. The salts containing multivalent ions had a greater impact than the monovalent ions, in keeping with the literature. A relationship between gas holdup and ionic strength was established. The concentration of frother (methyl isobutyl carbinol, MIBC) giving equivalent gas holdup was determined. The effect of salt and frother combinations was also explored.Proposed mechanisms for coalescence inhibition in salt solutions are briefly reviewed in light of the current findings.

Jan 1, 2006

By M. Vaillé, B. Bossé, N. Durupt, A. Michaut

Imouraren is a sedimentary uranium deposit (> 150,000 tU @ 800 ppm), located approximately 100 km North-Northwest of Agadez (Niger); its depth reaches 110 to 170 meters. For low-grades ores, heap leaching is commonly considered as the appropriate technology for metal recovery. More precisely, the ore is crushed (≤ 300 mm) and agglomerated before being stacked. In this case, sulfuric acid can be added during agglomeration and/or irrigation (for three months to a year) to improve uranium recovery. It is known that mineralogical, chemical and physical properties of the uranium ore impact recovery, yet many challenges remain to increase recovery using this process. For example, ore heterogeneity and spatial variability (e.g., variation in uranium, carbonate and/or clay contents) can affect heap leaching performances (i.e., metal recovery, acid consumption or neutralization, percolation rate). However, laboratory column tests using composite ore sample that do not consider ore heterogeneity are widely used to anticipate recovery. Consequently, a new approach that consists in using Imouraren drill core ore samples was recently investigated. This latter also enabled a better assessment of the main parameters that influence uranium recovery and proposed a new predictive model to optimize mining operations.

Jan 1, 2020

By V. G. c Papangelakis, M. Huang

A conductivity cell, developed previously, was employed in an effort to investigate the inter-relation between electrical conductivity and acidity of sulphuric acid - metal sulphate solutions at high temperatures. The measured solutions include the H2SO4-H2O, MgSO4-H2O, H2SO4-MgSO4-H2O, H2SO4-MgSO4-Al2(SO4)3-H2O solutions. All solutions reported in this paper were measured from 15 to 250 °C at equilibrium vapour pressure. The maximum measured concentrations of H2SO4, MgSO4 and Al2(SO4)3 were 0.45 m, 0.30 m and 0.10 m, respectively. It was found that, from 15 to 250°C, there is a linear relationship between H2SO4 concentration and electrical conductivities for acid concentration up to 0.45 m. At 250 °C and constant H2SO4 concentration, the solution conductivity drops with the increase of MgSO4 concentration. Lt is suggested that this drop is caused by a decrease in the concentration of H. Finally, an empirical model was developed based on the available measurements. This model has been tested against real laterite leach solutions where sulphuric acid and metal sulphates are dominant electrolytes. The average difference between the estimate acid concentration from this model and the one from titration was less than 5%.

Jan 1, 2004

The following briefing is intended to provide an overview of the present and future challenges associated with our access to a secure and adequate supply of electrical energy necessary to support safe, productive and sustainable mining initiatives at Musselwhite. Contents ??Site power demand vs. current available supply ??Supply technical deficiencies ?adequacy and security of present supply ??Present internal generation ??Anticipated future internal generation requirements ??Increased requirements necessary for planned expansion ?demand/security ??Goldcorp?s strategy to achieve required supply ?transmission line initiative ??Subsequent benefits to others from the Goldcorp initiative. ??Economic impact of MusselwhiteMine on the northwest region ??Anticipated economic impact of planned expansion ??Expected life cycle of MusselwhiteMine ??Comparative energy costs for similar operations in other jurisdictions ??Conclusions ??Anticipated action plan ??Energy Management Initiatives ??Site Orientation

May 1, 2009

By D. P. Bishop, G. J. Kipouros, R. L. Hexemer Jr., I. W. Donaldson, W. F. Caley

Aluminum powder metallurgy (APM) is an advanced metal forming technology frequently employed to fabricate complex structural components in a near-net-shape fashion. Exhibiting nearly 100% material utilization, APM continues to rise in popularity. Recent research initiatives in this field have emphasized the development and processing of advanced 2xxx and 7xxx series alloys. In particular, APM equivalents to wrought 7075 and 2024 have been sought. An overview of work completed in this area is presented. Included are data on the various production stages (powder compaction, sintering, forging, and heat treatment) as well as the microstructure and mechanical properties of the finished products.

Jan 1, 2010

By C. K. Wilton

"The Agnew Lake uranium deposits were discovered in 1953 following the discovery of the Elliot Lake deposits to the west. The original property was optioned to Kerr Addison Mines Limited who added additional claims by staking. Agnew Lake Mines Limited was incorporated in 1967 to develop the property and a shaft was sunk to 1040 metres and five levels developed before work was suspended due to low uranium prices at the end of1970.In 1974-75 the mine was dewatered and production started in 1977. By 1978 reserves were estimated at 10,000,000 tonnes averaging 0.35 kg. U10 , per tonne. Underground operations were terminated in 1980 although a uranium leaching operation was continued until early 1983.The deposits lie near the contact of Huronian metasediments with underlying Algoman granite. The sediments consist of arkose, conglomerate, argillite and quartzite with the uranium mineralogy mainly confined to oligomictic quartz pebble conglomerate. The higher uranium values are related to conglomerate with highest percentage of pebbles. The chief uranium minerals are uranothorite and monazite. It is of interest that the uranium thorium ratio differs appreciably from that of the Elliot Lake deposits. This fact along with the fact that the Elliot Lake sediments were deposited by paleocurrents from the northwest whereas the Agnew Lake sediments were deposited by paleocurrents from the northeast indicates widely separate sources for the deposits. It is suggested that the Agnew Lake uranium deposits are syngenetic placers deposited under anoxygenic atmospheric conditions."

Jan 1, 1986

By S. Leong

This paper reports on research examining disclosures from mining companies regarding their water usage in the Macquarie and Lachlan catchment areas, both parts of the Murray-Darling Basin in New South Wales, Australia. The objective of the research was to assess whether this disclosure is sufficient to allow communities to determine whether mining companies are complying with mining conditions of consent and abiding by the requirements of their water licencing agreements. These requirements are then compared to the water reporting requirements of the Global Reporting Initiative (GRI) and the Water Accounting Framework for the Minerals Industry (WAFMI). Communities are concerned about whether the mining industry?s use of water will have impacts on their livelihoods and lifestyle and thus require information concerning the quantity of water that will be extracted, how much water will be left for other stakeholders and whether the mining will affect water quality. This is an archival study. It has involved examining relevant publically available information released by mining companies and government regulators and determining if this is sufficient to meet the needs of the local communities. Additionally, it has involved looking at information indirectly provided by mining companies, via the use of intermediaries. Further, information availability concerning basic water accounting and regulatory breeches and whether such information is available at the mine site level has been considered. It is found that while NSW legislation places very little reporting requirements on mining companies, the development consent conditions for new projects and extensions to existing projects are quite significant and should be sufficient to meet the needs of local catchment residents though such information is not always easily accessible for the layperson.

Aug 1, 2013

By J. Shahabpour

"Abstract - Breccias with angular and rounded clasts of a late-mineralization, ""barren"" hornblende porphyry dike set within a comminuted matrix consisting of rock fragments and quartz, cemented by quartz and K-feldspar of hydrothermal origin is observed in diamond drill cores from the Sar Cheshmeh porphyry copper deposit. Studies of age relationship between vein types, phyllic-altered clasts and the breccia groundmass suggest that the brecciation is a late event. The breccia clasts record evidence of hydrothermal reaction between the clasts and fluids responsible for the brecciation.Formation of bornite, in the breccia clasts of the originally barren hornblende porphyry dike, and in the breccia matrix, along with the scarcity of bornite in the Sar Cheshmeh deposit itself suggest involvement of fluids which are later and of different composition from the fluids responsible for the known mineralization at Sar Cheshmeh. These later fluids may be related to a later plutonic event and suggest the possibility of a later, and concealed deposit."

Jan 1, 1994

By J. A. Espinosa-Guillen, J. A. Lopez-Molina, S. García, J. A. Valencia-Quintanar

"The design and implementation of grouting treatments in rock masses are procedures that require continuous adjustment of parameters and criteria to optimize the results. In this proposal we describe a set of tools that enhance decision-making for this type of jobs particularly in dam projects. The methodology is focused on hydrogeological zoning of the site and its constant update combining engineer’s experience with artificial intelligence techniques to integrate the site knowledge; as well as the evaluation of grouting results for different scrutiny scales, with special attention on the relationship between water absorption and grout consumption. INTRODUCTIONSeveral methodologies for design, implementation and evaluation for grouting rock masses have been developed for the solution of specific problems and tested in diverse geological conditions. Each of these methodologies is focused on results evaluation for different scrutiny scales (Table 1) and is employed to assist decision-making before or during the grouting process.Some methods define specifications for grouting each stage of the borehole, making theoretical, semi empirical or experience-based considerations to define basic parameters as maximum pressure, maximum volume, grouting time, flow rate, etc. Ultimately each approach aim to optimize the injection process, adjusting volumes or the grouting time required to obtain satisfactory results, reducing risk of creating new flow paths or unnecessary grout travels, and enhancing the mixture properties to achieve adequate penetrability and long-term behaviour. Some of these criteria have been widely used in dam projects, for example the concept of Grouting Based on Facts to define the maximum pressure and volume (Ewert, 1997), the GIN method (Lombardi & Deere, 1993; El Tani, 2012), or the North American standards based on Apparent Lugeon measures (Naudts, 1995; Bruce 2011); on the other hand, there are relatively new criteria that have shown good results for dam grouting as the Aperture Control Method (Bonin et al., 2012; Carter et al., 2012) or the Real Time Grouting Control Method (Stille et al., 2012)."

Jan 1, 2015

By Liu Liu

In the recent 10 years the rapid development of Chinese steel industry has attracted the attention of the world. The technological progress of converter steelmaking has played an important role in this process. First of all, slag splashing has been extensively adopted by Chinese steel companies in various sizes of converters from largest to smallest ones, and even including those using special hot metal containing V and Ti. Remarkable metallurgical results have been achieved. Up to now the average converter campaign life has reached nearly 10,000 heats, and the longest exceeds 30,000 heats in three melt shops. Based on this process, the long-life combined-blowing converter steelmaking technology has been developed. Slag splashing has been used to form a gas permeable "slag mushroom" on the top of bottom nozzles to protect the nozzles. In order to keep the effective bottom blowing, furnace bottom thickness control technique has been developed to prevent the furnace bottom growth. It makes the service life of bottom nozzle the same as the converter campaign life (average 10,000 heats and longest > 30,000 heats). The complete combined blowing was ensured through out the furnace campaign. Concentration product [C][0] is in the range of 0.0023 ~ 0.0030%, the T.Fe in the slag is lowered by 4 ~ 6%, and the [0] in steel is decreased by 100 ~ 250 ppm.

Jan 1, 2004

By Parviz N. Farsangi, Ferri P. Hassani, Allen G. Hayward

"Kidd Creek Mines places approximately 10 000 tonnes of consolidated rockfill (CRF) daily. Consolidated rockfill comprises sized aggregate mixed with different ratios and amounts of binders. Consolidated rockfill is employed to simplify subsequent pillar recovery and provide improved passive/active ground support.The consolidated rockfill is designed to sustain not only the gravitational loading of the overlaying fill material, but also to some extent the dynamic loading applied during blasting of the adjacent stopes and/or pillars. This paper describes the steps taken to optimize the pre-sent fill system at Kidd Creek Mines.The emphasis is on four areas which have high saving potential: lower cost alternative binders, structural design, quality control measures, in-situ testing techniques for back analysis. A consolidated rockfill design optimization chart was developed from these investigations."

Jan 1, 1996

By J. Fournier, D. Fortin, F. Robichaud

Since milling began in 1988, the Laronde mill has been expanded several times, the most recent, increasing the milling rate from 5 000 to 7 000 mtpd. Laronde uses SAG/ball mill grinding followed by copper and zinc flotation circuits. A cyanidation/Merrill-Crowe process recovers the remaining gold and silver in the flotation tails in order to cope with high silver/gold ratio associated with the discovery of the Penna shaft. Since the commissioning of the Merrill-Crowe refinery in 2000, several modification and expansion projects were performed to reduce health and safety hazards. Remarkably, several of these improvements have contributed at increasing productivity and Net Smelter Return of the refinery while reducing worker's injuries. In 2004, the refinery was audited to evaluate and quantify the circuit performance. Metallurgical and mechanical operating conditions of the refinery are now understood and areas for further improvements are well defined. This paper describes some of the factors that have contributed to this improvement and describes how ergonomics and recovery can further be improved.

Jan 1, 2005

By J. Qi

Based on the commercial steel 42CrMo (4140, SCM440), a new generation of CrMo steel was developed by increasing the content of Mo, adding the alloy element of V and Nb, and decreasing the content of P and S. This new CrMo steel has higher strength of 1500MPa and better delayed failure property. TEM and EDS were used to study the distribution and function of the alloying elements in this steel. A new EELS technique was developed to study the bonding strength of the grain boundary in the steel. The mechanism of strengthening of the new steel has been studied.

Jan 1, 2004