Search Documents

By P. Sauriol

This work addresses the design challenges and demonstrates the capabilities of a novel water transfer factor measurement apparatus. Several measurement concepts were screened on the basis of their water transfer factor accuracy using Monte-Carlo generated virtual experiments. The most promising measurement concept was assembled and tested to assess its actual measurement accuracy. For these concept validation experiments, the polymer electrolyte membrane fuel cell was simulated by adjusting the water injection rate to corresponding levels. Combining the anode and cathode measurements, the water transfer factor accuracy was typically better than 0.01. Real-time measurements of the water transfer factor on both anode and cathode sides of a polymer electrolyte membrane fuel cell were achieved. The anode and cathode side measurements were in good agreement with each other; however the anode side measurements were generally more reproducible. A parametric study showed that stream humidification plays an important part in the water transfer across the membrane electrode assembly. Finally the water transfer factor along the channel of a 300cm2 co-current fuel cell was obtained by using a series of six 50cm2 sub cells. The results were in good agreement with predictions from a recently proposed model.

Jan 1, 2005

By L. Vinnett, T. Ledezma, F. Contreras, F. Díaz

"Mass balances in secondary grinding are subject to critical constraints mainly because of the unknown load distribution from the SAG mills, the uncertainties in the hydrocyclone split estimations and the lack of flowmeters in the key streams. In this paper, a methodology to support mass balances based on the use of radioactive tracer is presented. This approach was successfully implemented in two secondary grinding circuits of Minera Los Pelambres, which operate with ball mills of 21’ x 33.5’. The method allowed the load distribution of the SAG product (secondary grinding feed) to be determined. This load distribution was used as an input in the mass balance data reconciliation.The effective residence times of solid tracers were obtained in the secondary grinding equipment, where irradiated solid was used as a tracer. The residence times were obtained from the parametric deconvolution between the input and output tracer signals. The model fitting was performed to reconstruct the normalized output tracer concentration. Effective residence times of solid tracers in the ball mills ranged from 1.9 min to 9.5 min. The use of radioactive tracer measurement in grinding circuits is a powerful tool to consolidate mass balance results as well as to characterize grinding mills.INTRODUCTIONGrinding is the last stage of the comminution circuits. At this stage, the ore particles are reduced in size by a combination of impact and abrasion, either dry or wet (Austin & Concha, 1994). The grinding equipment mostly used in industrial operations correspond to horizontal tumbling mills (Wills & Napier- Munn, 2006). Tumbling mills employ steel balls or rods as grinding media. Ball mills, which are a type of tumbling mills, use steel grinding media with greater surface area per mass unit than SAG (semiautogenous grinding) mills or rod mills (primary grinding). Hence, the ball mills are suitable to obtain the particle size required in the next separation stages (Napier-Munn et al., 1996; Wills & Napier-Munn, 2006)."

Jan 1, 2016

By N. J. Contini, R. W. Knopp

"In March 1988, old Denver flotation cells were removed from Dickenson's Arthur w. White Mill, and a new flotation circuit, consisting of four Prochem rougher cells and a Hydrochem agitated cleaner column, was commissioned. The refractory portion of the gold in the ore is associated with arsenopyrite, therefore the flotation circuit is set up to produce a saleable sulphide concentrate. Tailings from the leach circuit are conditioned prior to being pumped as feed to the flotation circuit. The prototype Hydrochem agitated column has been in operation as a single cleaner stage for rougher concentrate. The effect of flotation circuit changes on gold recovery data, as well as cleaner concentrate production, and development work to achieve the target results, have been investigated. Flowsheet modifications and the resulting circuit performance data, along with test results to date, will be presented.INTRODUCTIONThe mill is capable of treating 1000 stpd of ore averaging approximately 0.30 oz/ton Au. The ore is crushed and ground to 75% - 200 mesh. Gravity concentration, cyanidation, and Merrill - Crowe precipitation yields 84% gold recovery. Detailed descriptions of the comminution, gravity separation, and leaching circuits, as well as background information have been presented elsewhere (Suttill, Van Weert et al). The target cleaner concentrate grade is 1.0 oz/ton Au for custom smelting and refining. Historical gold recovery values of the old circuit was approximately 20% of the gold present in the float feed at the target grade. The recovery value objective set for the new circuit during the planning stages was 50% of the gold present in the flotation feed at 1.0 oz/ton Au in cleaner concentrate."

Jan 1, 1989

By Norman Orr, J. W. Gregg, Jack Wahl

The Pembina Cardium pool is a low permeability, stratified, solution-gas drive reservoir. Water-flooding has proven to be an effective means of pressure maintenance for all areas of the pool in which an economic rate of water injection can be maintained. The majority of water injection wells in the pool are converted oil well~ with capacities greater than 100 millidarcy-feet. If the average injection rate per unit of capacity can be in-creased the lower capacity areas of the pool can be economically flooded. Theory, laboratory work, and two . early miscible-flooding projects with-in the pool suggested that average water injection rates for converted wells could be increased two to three-fold by the initial injection of natural gas liquids and natural gas. How-ever, these two early projects received volumes of natural gas liquid!:' and high-pressure natural gas which would be economically prohibitive for routine stimulation. Area D, one of the Five-

Jan 1, 1962

By L. Li

To accommodate the large payloads and harsh operating conditions associated with heavy vehicles in the mining industry, off-the-road (OTR) tires are typically used with heavy mining vehicles. These tires have increased abrasion and wear resistance due to their thicker tread, sidewall and bead thicknesses. Given these features, OTR tires are much stiffer than conventional passenger vehicle tires and cannot be mounted to a single-piece rim without damaging the structural integrity of the tire during the mounting process. Therefore, multi-piece wheels are used with OTR tires to facilitate mounting. While these assemblies are necessary, several instances of their failure have been reported to result in injuries or fatalities within the mining workplace. Many of these failures were specifically reported to be caused by the disengagement of the wheel lock ring - a component used to securely engage the assembly during operation. In this study, a threaded-connection locking mechanism has been proposed in place of the traditional lock ring design. The performance of this threaded-connection was numerically evaluated in a pull-out test against a conventional five-piece wheel assembly. The pull-out test was devised as a means of quantifying the engagement ability of each wheel?s locking mechanism. A high degree of modelling accuracy was maintained throughout the analysis by validating the vertical and horizontal static loaddeflection behaviour of the rim model of the five-piece wheel assembly against experimental data. Through validation, the model data were found to be within 10.5 and 4.80 %, for vertical and lateral loaddeflection behaviour, respectively. Results from the pull-out analysis found that the threaded-connection demonstrated a 113 % increase in the force required for disengagement to occur relative to the conventional five-piece design - a force of 9,550 kN in total.

Aug 1, 2013

By Dirige. A. P. E.

A study was conducted for an operating mine to determine the appropriateness of its tailings material to be used for the preparation of a low modulus, high density backfill. The research was initiated due to issues arising from increased observations of compressive failure of backfill placed in stopes and inconsistent backfill behaviour (i.e. increased backfill brittleness and modulus). Backfill materials investigated were classified tailings and de-slimed tailings. Characterization of the physical properties of the classified and de-slimed tailings materials was conducted to assess the effect that these material properties would have on the strength and deformation behaviour of high density backfill products made using them. Such behaviour was investigated to determine whether differences in tailings physical properties would influence the strength and modulus character of the backfill materials. Uniaxial (UCS) and consolidated-undrained triaxial compression strength tests were conducted to determine strength performance and deformation behaviour of backfill. This paper presents the results of the backfill material characterization study and how different particle size distributions affected the strength performance and deformation behaviour of the different backfill mixes. It also demonstrates how stress-strain curves generated from material strength tests were used to evaluate variation in high density backfill mix response when such materials were subjected to unconfined and confined (triaxial) compression loading.

Aug 1, 2013

By O. G. Olvera, L. S. Quiroz-Castillo, P. J. Valenzuela-Guerrero, D. G. Dixon

The effect of sulfuric acid concentration on the extractions of arsenic and copper in the catalyzed batch leaching of an enargite concentrate was studied. The acid concentrations studied were 60, 45, 30 and 15 g/L. The experimental series yields maximum copper extractions of 96 to 98% in an interval of 81 - 185 h leaching time for 60 - 15 g/L initial sulfuric acid concentration; all the copper extractions plateaued after these values; the rates and plateaus of copper extraction are increased with higher acid concentrations. Arsenic extractions reached maximum values of 89% in 57 hours, 57% in 49 hours, 33% in 25 hours, and 25% in 112 hours respectively; these maximum values were followed by a steep decrease in arsenic concentration, which indicates a precipitation event occurs in the process. According to the literature and process conditions, the arsenic precipitates obtained are iron arsenates similar to scorodite. The stability of the residues was tested using the Toxicity Characteristic Leaching Procedure (TCLP) from EPA; the residues for the four concentration levels passed the TCLP test, reporting arsenic leaching values below 1 mg/L.

Jan 1, 2014

By S. Perez

Core drilling is a fundamental process in the mineral exploration industry. As deep exploration in hard rocks is accelerated due to the depletion of near ground mineral resources, deep-drilling operations need to reduce their reliance in operators experience and begin to implement new technologies in order to increase efficiency and cost-effectiveness of the overall process. Currently, lack of real-time information on the bit/rock interaction is a major problem. Therefore the mechanism behind the acoustic emission, which is a proven technique for remote monitoring, generation in mechanical rock cutting must be understood in order to provide real time information about the rock. This paper aims to identify the influence of mineral composition of granitic rocks on the acoustic emission (AE) during rock abrasivity test with a single contact tool and to evaluate the feasibility of AE as a means to infer Cerchar Abrasivity Index (CAI). Single contact tool will provide precise and accurate description of the source of AE. To provide constant grooving speed Cerchar apparatus was modified to monitor AE during rock/tool interaction. Tests on the modified Cerchar apparatus are carried out under the static load of 70N and cutting speed of 1 mm/s. A Scanning Electron Microscope (SEM) is utilized to visualize the groove in the rock and to identify the mineral composition through Back-Scattered Electrons (BSE) reflected from the rock sample. Based on the microscope images, it was found that biotite shows a larger groove area and plate-like fractures accompanied with burst-type AE signal, whereas plagioclase and quartz, which are characterized by similar hardness and BSE brightness, possess shattered-like fractures and more continuous-type AE signals. In addition, a-value of the Gutenberg-Richter scale has been found to well correlate with Cerchar Abrasivity Index (CAI).

Jan 1, 2015

By Niraj Bala

Boiler tubes of coal-fired boilers suffer severe erosion-corrosion (E-C). One method to counteract this problem is by the use of therma, spray protective coatings. Cold spray coating process was used to deposit Ni-20Cr powder on SA 516 (Grade 70) boiler steel. The bare as wel, as the coated steels were subjected to cyclic experimenta, studies, in the superheater zone of a coa, fired boiler. The weight change technique was used to establish kinetics of the erosion-corrosion. XRD, FE-SEM/EDS and X-ray mapping techniques were used to analyse the as-sprayed and corroded specimens.

Jan 1, 2010

By A. Warczok

Metal losses in discard slag are the main factor determining overall recovery. The metals are present both in dissolved form and as matte or metallic inclusions, varying in size from 2 to 1000 µm. Pyrometallurgical slag cleaning usually consists of heating the slag, reduction of oxides and settling of matte/metal droplets. Heating the slag decreases viscosity and accelerates reactions. Reduction of magnetite liberates inclusions and facilitates co-reduction of dissolved metal oxides. A significant amount of the matte and metal is present as very fine metallic inclusions, too small for settling. The coalescence of these matte or metal inclusions is required to remove them from the slag. The developed new concept of slag cleaning combines DC furnace technology with an extra magnetic field for vigorous slag stirring, enhancing mass transfer to the reductant surface, accelerating the rate of reduction, and destabilizing the emulsion of matte or metal inclusions. Intensive slag stirring increases the probability of collision of inclusions, will accelerate their growth and will therefore improve settling. The process is carried out in a patented DC channel furnace, where the liquid metal or matte layer acts as a cathode and the floating coke bed on the slag surface is the anode. In the first part of the furnace, a superimposed magnetic field induces a Lorentz's force causing the slag to start an intensive circular motion. The next furnace zone does not experience any stirring and is dedicated for quiet sedimentation of the inclusions. A mathematical model of gravitational coalescence combined with forced slag motion showed the possibilities of effective removal of copper matte inclusions. The results of laboratory pilot scale tests of continuous slag cleaning showed fast slag reduction and confirmed the improved matte removal from the slag. Conceptual analysis shows the potential use of the technology in various other non-ferrous industries, like for example nickel plants. It is also possible to use this technique batch wise.

Jan 1, 2007

By J. Graham Eby

"This paper describes the development and some typical applications of Wemco's large-capacity flotation machines, the No. 120 and the No. 144, with volumes of 300 and 500 cubic feet, respectively. During the 1960's, it became obvious that low-grade orebodies would be mined at high tonnage rates - plants and grinding mills would be larger, which would create a demand for larger flotation equipment. To meet this demand, Wemco developed a single-mechanism, 300-cubicfoot cell, having five times the volume of the standard No. 66 cell. The average production rate of the No. 66 cell on porphyry copper ore was 100 tpd per cell; and it was our intention that the No. 120 (300-cu. ft) cell would handle 500 tpd per cell, with at least equal metallurgical results and power consumption per ton. The success and industry acceptance of the No. 120 cell has since led to the development of a larger cell, the No. 144, having a volume of 500 cubic feet."

Jan 1, 1972

By V. A. Leão, A. M. Silva, S. M. Bertolino, B. C. S. Ferreira, D. Guimarães

Although not considered a high risk pollutant as compared to toxic metals and acidity, environmental agencies worldwide are proposing regulations to control sulphate in effluents and drainages by setting a threshold value varying between 250 mg/L and 500 mg/L. The aim of this study was thus to compare four different techniques for removing sulphate ions from mining/metallurgy effluents. The first alternative studied was sulphate removal by precipitation as ettringite. Treating a synthetic solution containing 1650 mg/L sulphate at 22±1 ºC resulted in removals close to 85% during continuous precipitation. Sulphate sorption was also investigated using three different ion exchange resins as well as limestone. Fixed bed experiments produced sulphate loadings of up to 70 mg SO4 2-/L resin, at pH 2.0. In neutral wastewaters, limestone is also a potential adsorbent producing a maximum particle loading of 19 mg/g. Sulphate sorption on limestone seems to be an alternative to treating mine waters with sulphate concentrations below the 1200-2000 mg/L range, where lime precipitation is not effective. Subsequently, sulphate removal by sulphate reducing bacteria was also investigated and it was observed that reactor’s hydrodynamic conditions and the choice of substrate are important factors for the process. The different technical aspects of each technology are addressed.

Jan 1, 2014

By Xiqing Wu, Liang Dai, Tao Yue, Longsheng Yi, Ruifang Wang

Magnetic seeding flotation (MSF), i.e. adding magnetic seeds and pre-magnetization-flotation, is a new flotation technology especially for fine particles, which improves the flotation performance by enlarging the apparent size of the particles in a way of magnetic agglomeration. Both the fine coal slimes with a size of 66.68% –38µm and the pyrite slimes with a size of 73.95% –23 µm were investigated by the MSF, respectively. Flotation tests with variable of dosages of magnetic seeds and polyacrylamide were conducted, and some measurements, such as laser diffraction size analysis, magnetic susceptibility by vibrating sample magnetometer (VSM) and infrared spectroscopy (IRS), were also applied in order to probe the mechanism of the MSF. Based on the tests, measurements and calculations it was found that both the recovery of coal and the flotation kinetics of pyrite slimes increased with the additions of the magnetic seeds, and in the presence of polyacrylamide the coal flotation was further strengthened due to a synergetic effect of magnetic seeds and polyacrylamide on the flotation and a relatively larger apparent size of slimes after additions of magnetic seeds and polyacrylamide. The reason for the MSF lies in fact that the presence of the polyacrylamide intensified the adsorption of magnetic seeds on the coal particles and increased the coverage of the magnetic seeds on the coal surface from 0.2 to 1.3 wt%, resulting in increased magnetic susceptibility of coal particles from 9.13×10-9 to 22.17×10-9 m3/kg and thus a low magnetic field strength of pre-magnetization needed for the magnetic agglomeration among the coal particles from 602 to 24 mT prior to proper flotation. IRS shows that polyacrylamide chemisorbed on the surfaces of both coal particles and magnetic seeds, thus acting as the bridging media between particles and seeds.

Jan 1, 2016

By F. Azgomi

A possible way to characterize (classify) frothers using gas holdup as a surrogate for bubble size was explored. Nine surfactants with a range in chemical structures were selected and tested in a bubble column instrumented to measure gas holdup and superficial gas velocity. A correlation between frother type and gas holdup was observed: for alcohols, gas holdup increases with hydrocarbon chain length and the effect is the same whether the chain is branched or straight; for polyglycols, gas holdup increased with number of propoxy groups. The ranking by gas holdup gave the same result as other frother characterization techniques.

Jan 1, 2006

By Q. H. Bui

The elastoplastic self-consistent model is one of the effective models to study the initial microstructure effect on the mechanical behavior of bulk materials. However, the use of this micromechanics-based model which takes into account only the Hall-Petch relationship at grain level for predicting the grain sized effects on the strength of the deformed materials is not accurate yet because of the fact that the dislocation density contributes also to the strengthening of this kind of materials. In this study, a modification made to the Hill-Hutchinson elastoplastic self-consistent model was proposed for investigating the microstructure dependence of the mechanical behavior of cold-drawn 6063 aluminium tubes. Because of the novel modification, an estimation procedure with two steps was required to identify the parameters of this micromechanical model. An acceptable agreement between experimental and theoretical stress-strain curves was achieved.

Jan 1, 2011

By E. S. Moore

DEEP oxidation and-secondary enrichment of ore deposits, although so important in many parts of the world, are comparatively rare in the Canadian shield. Intensive glaciation during the Pleistocene epoch accounts for their rarity. Glaciation has cost Canada much in the destruction of not only enriched ore deposits, but placers that must have been developed near our numerous gold deposits during the long period of weathering that pre-ceded the Pleistocene. There seems to be a very common misconception regarding the average depth of rock that has been removed from the shield by glaciers. These bodies of ice are usually given credit for the removal of the greater portion of the thousands of feet of rock that we know has been eroded from this large area since Precambrian time. As a matter of fact, the average thickness of solid rock removed can be measured in tens rather than even hundreds of feet, although very deep erosion has resulted in some sections where the glacial ice has been constricted in depressions, such as deep valleys and lake basins. On the other hand, there are few areas within the shield where the glaciers have not disturbed practically all of the mantle rock and some feet of the underlying bed-rock. The chances of finding deeply oxidized cappings and enriched ore deposits are therefore comparatively few and these have been found chiefly where favourable structural and topographic conditions for their formation and preservation have existed. Faulting has been responsible for several of these deposits, and easily decomposed rocks, such as. sulphides and carbonates, have been very important factors. Topographic features, such as high and resistant hills, favourably situated with respect to the ore deposits have, in a few cases, played a part in providing protection from glacial erosion and in furnishing head for the descent of surface waters. At least four cases of oxidation to depths quite abnormal in the Canadian shield have so far been found in Ontario. These are the Helen and Josephine iron mines in the Michipicoten district, the Keeley silver mine in South Lor-rain, and the Ross gold mine in Hislop township, Cochrane district. A deeply oxidized zinc deposit of unusual interest occurs in the Precambrian rocks in New York State, not far from the Canadian border, and there arc the well-known iron deposits in the Lake Superior region of the United States.

Jan 1, 1938

By K. Ghyselbrecht, R. Swennen, Y. W. Chiang, V. Cappuyns, R. M. Santos, T. Van Gerven, B. Meesschaert

Heavy metal contamination from mining and metallurgical activities of aquatic systems poses significant risk to the environment and human populations. The investigation of the distribution and immobilization mechanisms of heavy metals in sediments and soils has recently attained high priority. Different remediation methods can be employed to suppress or eliminate these contaminants. A tailored approach using both commercially available and in-house made adsorbents to rem ediate a heavy metal contamination site due to historical metallurgical activities in north Belgium is studied in this paper.

Jan 1, 2011

By G. Zárate, G. Tapia

Anglo American Chile has been doing copper concentrate leaching studies at the laboratory and small pilot plant scale since 1992. Among the processes evaluated are bacterial leaching and pressure leaching using Mantos Blancos, Salobo Project and Quellaveco Project concentrates. Late in the nineties, it was decided to focus the research on pressure leaching, either medium or total pressure oxidation. Preliminary scouting tests were run with Mantos Blancos concentrate samples during 2000, which were repeated during 2003 together with samples of Los Bronces and El Soldado concentrates, in order to define the most suitable concentrate for running a pilot plant campaign at AARL, which was carried out in two campaigns, a first one from November 2003 through January 2004 and a second one during April 2004. Mantos Blancos was the selected concentrate and the laboratory and pilot plant results are discussed in this paper together with some preliminary economic estimates.

Jan 1, 2004

By Balmer Neilly

FOR some reason or other, Mine Taxation has never been a popular subject for discussion in meetings of this kind, and it has never received the study and consideration its importance demanded. By way of explanation, two reasons may be suggested. In the first place, the computation, adjustment, and final payment of taxes, have been looked upon in most cases as a Head Office chore. Secondly, since taxes represent an uncontrollable cost item, they have been treated as an added rather than an inclusive factor in calculating unit costs. Perhaps because I am half Irish, and therefore resent taxation of all kinds, perhaps because I am half Scotch, and am therefore concerned with the results, I have always taken a keen interest in this subject. Moreover, by some peculiar set of circumstances, I have been a participating party in many, perhaps I can say most, of the discussions on this subject that have taken place between the Governments and the representatives of this industry during the past thirty years. Looking backward, certain very definite impressions remain. Political considerations have never had any part in these discussions. Views have been exchanged upon the frankest possible basis, and, when we disagreed on some particular detail, we agreed to disagree, and followed through in harmony and? good faith. We, as an industry, have refrained from importuning and fault finding in ways that might be considered as petty or selfish, and it is only upon occasions such as this, where conditions necessitate action, that we lay our troubles before the powers that be. The Ontario Mining Tax Act was drafted by men who were earnest and practical as to purpose, and that Act has stood the test of time. It is, in. truth, a mode! Act, for it has been copied in its general clauses by both Quebec and the Dominion of Canada. We all know that, when a machine is running smoothly, we should leave it alone. The same is true of a well designed, easily applicable, taxation measure, and our present difficulty with respect to this Act arises out of an amendment made in 1916. In that year, you will remember, the Dominion imposed a wartime Income Tax Act. It was described as a wartime necessity and it was intimated t:1 at with the end of hostilities its application would be restricted and finally cancelled. The rate of taxation was modest, and when the Ontario Government was asked that the Dominion Income Tax be allowed as a deductible item, they readily acquiesced. This was looked upon as a temporary arrangement.

Jan 1, 1943

By Northeastern University, B. Y. Cui, B. Y. Wang, D. Z. Wei, W. G. Liu, Z. C. Guan, S. L. Gao

To recover iron values from low grade ores by reverse froth flotation method, further research on cationic collectors used in reverse flotation of iron ores is launched to promote the utilization efficiency of iron ores. In this paper, one new cationic surfactant, bis(2-hydroxylethyl) dodecylamine (BHD), that could be dissolved in water easily was used as collector for quartz flotation. Flotation results indicated that BHD shows stronger collecting performance on quartz than hematite. The maximum recovery of 96.30% to quartz is obtained at a collector concentration of 20.0 mg/L in the pulp pH range from 5 to 7. This collector can be used to float quartz from hematite. And optimal separation results with 86.59% iron recovery and 66.60% iron grade to synthetic sample were achieved at a collector concentration of 20.0 mg/L and pulp pH of 5.02 when hematite and quartz were mixed at a mass ratio of 3:2. The adsorption mechanism of the collector on quartz surface was investigated by XPS analysis, infrared spectroscopic analysis and zeta-potential measurements, which revealed that electrostatic attraction and hydrogen bonding adsorption occur between collector and quartz surface.

Jan 1, 2016