Search Documents

By J. F. Boux

"The study of the total utilization of fly ash has involved all of the known technology in the processing of this waste material into useful products. In addition, a complete knowledge of all the possible uses of fly ash and its products in the market area was probably the most important factor in evaluating the theory and practical feasibility of the total utilization of fly ash from a single large supplyLaboratory tests carried out on the separation of fly ash into different fractions were shown to improve its value and utilization. Four main fractions were studied: a fine pozzolanic low-carbon fraction; a coarse fraction for light-weight aggregate production by pelletizing and sintering; a high-iron fraction; and a carbon-rich fraction. The term ""beneficiation"" here refers to a process of separating fly ash into more useful components.Laboratory and pilot sinter strand tests were employed to optimize the sintering capability and the quality of the heat-hardened pellets through a study of the agglomeration cycle in four principal heat zones, under controlled conditions of air flow, temperature and atmosphere, and including the controlled sizing of pellets.The suitability of the heat-hardened pellets as light-weight aggregate was evaluated in test batches of concrete, which were compared with concrete containing commercial lightweight aggregate of established quality.A study of beneficiated fly ash pozzolan as a partial cementitious binder component in normal and high-temperature cured concrete was reported in a paper at the re-cent Second International Fly Ash Symposium.Samples of raw and beneficiated Lakeview ash were compared with samples of other established high-quality fly ash pozzolans. The evaluation indicated the usefulness of beneficiated Lakeview ash as a pozzolan. Economic studies indicated that to accomplish the primary objective of total utilization of any single source of fly ash (in this case. fly ash from the Lakeview Generating Station, producing approximately 400,000 tons per year), a broad knowledge of the technology of various mineral processes was essential.The design of the fly ash processing plant had to be based on the disposal of all the raw fly ash produced by the generating station. This is contrary to the normal design of a processing plant in which raw materials are supplied and produced according to product demand. The design, therefore, had to be of such flexibility as to pro-duce as wide a variety of products as possible, and the ability to market them had to be well researched and understood."

Jan 1, 1970

By Lionel Roberge, Borge J. G. Fredriksson

"Late in 1981, a six-rope friction hoist was installed in the Number 2 shaft at Les Mines Seleine Inc. on the Madeleine Islands in Quebec. This paper deals with the reasoning behind the selection of hoisting equipment from the economical point of view, safety point of view, future needs point of view, etc.After establishing the basic parameters for the hoisting system, features of the most common types of hoists (i.e. single-drum hoist, double-drum hoist, Koepe hoist) are briefly laid out. The reasons for selecting a friction (Koepe) hoist are summarized. However, why go for a six-rope hoist rather than the (in North America) more common four-rope hoist? As the subject hoist is the first six-rope hoist in Canada, this question is studied in more detail, covering initial cost, maintenance cost, etc., as well as practical aspects, such as safety, physical dimensions, etc.In summary, experiences from other multi-rope hoist installations world-wide are presented.BackgroundIn 1980, Seleine Mines Inc. was established as a subsidiary of SOQUEM. The new mining company was to develop and operate a salt mine and associated harbour on the Madeleine Islands in the Gulf of St. Lawrence. The Madeleine Islands form part of the Province of Quebec. The mine has a planned annual output of 1.2 million metric tonnes of salt, with reserves in sight for over 20 years. Mining will be by room and pillar, with an underground primary crusher and treatment plant. From the underground treatment plant, the salt will be transferred via conveyors to a 5.5-metre-diameter circular shaft and hoisted to the surface. Surface transportation to the warehouse will again be via conveyor, and a conveyor will also transport the salt from the warehouse to the point of shiploading."

Jan 1, 1983

By M. H. ElMaghraby

This paper describes the development and validation of a strategy for vibration-based online detection of faults in a particular class of machinery commonly found in industry. This machinery is defined by two basic characteristics that preclude it from the application of standard online condition monitoring approaches. The first characteristic is that the machine is in a constant state of transient operation, thus making it difficult to differentiate between changes in transducer measurements that are due to variable duty and those that are due to machine malfunction or fault. The second characteristic is the fact that the machinery involves multiple sub systems that are subject to identical and simultaneous loading, operating environments and duty cycles. An example of such machinery is a system of multiple hydraulic pumps driving a common load. The monitoring strategy presented here employs an anomaly detection scheme together with methods of signal processing and feature extraction that exploit the parallel duty arrangements of this equipment. Preliminary data is collected from a pair or motor-gearbox assemblies used in a material haulage system in the mining industry. Testing and validation was performed on a mechatronic test bench with both healthy and faulted components. Experiments were carried out to investigate how various configurations of the system were able to detect different types of faults. The results indicate that this approach is effective and merits further investigation.

May 1, 2013

By Craig Dirk

Agenda Applications of ?GPS ?Drill Navigation ?Cycle time monitoring ?UDS / Boom Stress monitoring ?Payload systems ?Laser Surveying Future Applications

May 1, 2006

By R. B. Fermor

"The tyndalloscope is used in Europe for dust-hazard assessments in both coal and metal mines. Dust-hazard conditions can be directly evaluated by the tyndalloscope in many underground working situations, once the basic standard table or tables have been prepared from representative mine-rock samples.The tyndalloscope is excellent, in many cases, for diagnostic dust sampling during a working shift, because individual readings can be taken to within three-minute intervals. The limitations of the tyndalloscope are also discussed.The author suggests that a combination of both the tyndalloscope and gravimetric sampling methods would be an ideal match for most mine dust-hazard assessments."

Jan 1, 1970

By N. Aslin, R. Clark, G. Heferen

The methods of harvesting copper from stainless steel mother plates has been investigated from fundamental and operational experience perspectives. At least five different harvesting techniques have been identified that have different effects on product quality, current efficiency, current distribution, growth morphology and ease of stripping. Each method is examined from fundamental principles to understand what occurs during the harvesting process and why the particular effects are manifested. Experience from plants operating the harvesting method is provided to show that the fundamental understanding is relevant. Best practice harvesting method and harvesting management are described.

Jan 1, 2014

By Zolfan F. Oszter

As exploration for new mineral deposits advances farther into the Canadian North, the more the design engineer is faced with the problems of cold weather conditions. This is especially true when designing belt conveyor systems for open-pit operations where the temperature in the winter may go to -40°F or below. Problems with the mechanical components and also with the belting will arise, which in turn may reduce the availability of the system. This paper outlines the problems encountered during cold weather operation and what precautionary measures must be taken into consideration in the design of equipment, as well as in the selection of materials, in order to ensure a system which will maintain production. THE conveying of ore and waste in the pit or to the processing plant poses problems during cold weather, when temperatures may drop to -4o?F or be-low. Troubles with the mechanical components, the belting or the supporting structure may arise, and this, in turn, will reduce the availability of the conveying system.

Jan 1, 1965

By The Staff

Development of the Eldorado Mine THE pitchblende-silver deposits of Great Bear lake, Northwest Territories, were discovered by Gilbert LaBine in 1930. The property owned by Eldorado Gold Mines, Limited, consists of 53 claims situated, for the most part, on LaBine point, on the northeast shore of the lake. The Company also holds a group of 10 claims on Dowdell point, 7 miles to the southeast of the main group and across Echo bay. The fractures traversing the ridge on LaBine point can be readily seen from the air. Lack of overburden and the scantiness of vegetation leave rock exposures which are visible for miles. The years 1931 and 1932 were spent largely in staking, prospecting, and examination of the outcrops. A small Diesel plant was shipped to the property in 1932 and underground operations were started. Entry was made into the ore-body by means of an adit. A 20-ton mill was completed in the winter of 1933-34, and since then operations have been continuous, except for temporary shut-downs for additions to the mill. TRANSPORTATION The mine is situated 28 miles south of the Arctic Circle and is reached by an air route of 1,140 miles from Edmonton. The water route follows the course of the Mackenzie River system from Waterways, Alberta, the end of steel, and is approximately 1,450 miles in length. Two portages, at Fort Smith and on the Bear river, respectively, are necessitated by the occurrence of fast water. Transportation was one of the major problems to be solved, and Eldorado Gold Mines, Limited, found it necessary to embark upon both water and air freighting on its own account. The Company now operates a Bellanca 'plane with a payload of 4,400 pounds, and a complete water transportation system. The latter was established some years ago by the Northern Transportation Company and it is still operated under that name, but the Company is now a subsidiary of Eldorado. Modern steel boats, oil tankers, and barges were added to the fleet this season. The greater part of the ore shipments are made by water, aircraft being used for this purpose only when occasion demands. Freight rates have been greatly reduced by direct ownership of carriers. For example, water-borne freight is now quoted 'to the mine at $ll0 per ton, as compared with $240 per tan four years ago.

Jan 1, 1938

By Y. M. Jubeli

"Abstract - Gamma-ray spectrometry, an effective tool in geological mapping, was used to define boundaries between various lithological formations in three adjacent areas of Central Syria, namely, the Syrian Desert, Ar Rassafeh Badiayat and the Northern Palmyrides mountains. This paper describes the role of an airborne gamma spectrometric survey which was orginally undertaken to assist uranium exploration. Interpretation of the total count data obtained through the survey has led to significant modifications and corrections to the previously published distribution map of the palaeogene phosphate rocks.Another important result of the survey is the discovery of four previously unknown phosphorite horizons in the Rasm Al-Aawabed area of the Northern Palmyrides. In addition, previously unknown phosphatic horizons are outlined in the other study areas. The importance of this technique as an effective prospecting method, not only for U but also for exploring for the economically important phosphorite formations in Syria, is emphasized. Furthermore, its role in geological mapping is stressed, especially in areas that lack sufficient geological data."

Jan 1, 1997

By Y. M. Jubeli

"Gamma-ray spectrometry, an effective tool in geological mapping, was used to de?ne boundaries between various lithological formations in three adjacent areas of Central Syria, namely, the Syrian Desert, Ar Rassafeh Badiayat and the Northern Palmyrides mountains.This paper describes the role of an airborne gamma spectrometric survey which was originally undertaken to assist uranium exploration. Interpretation of the total count data obtained through the survey has led to signi?cant modi?cations and corrections to the previously published distribution map of the palaeogene phosphate rocks.Another important result of the survey is the discovery of four previously unknown phosphorite horizons in the Rasm Al-Aawabed area of the Northern Palmyrides. In addition, previously unknown phosphatic horizons are outlined in the other study areas. The importance of this technique as an effective prospecting method, not only for U but also for exploring for the economically important phosphorite formations in Syria, is emphasized. Furthermore, its role in geological mapping is stressed, especially in areas that lack suf?cient geological data."

Jan 1, 1997

By R. Aubertin, G. Panneton, P. Donovan

The Detour Lake gold project is located in northeastern Ontario, approximately 300 km northeast of Timmins, within the Abitibi greenstone belt in the northwestern portion of the Archean Superior Province. Historically this greenstone belt has produced approximately 180 million ounces of gold, largely from narrow vein underground mining. The Detour Lake project is a site of extensive past exploration since 1974, as well as underground and limited open pit mining activity from 1983 to 1999. During this period, it produced 1.8 million ounces of gold. Underground mining focused on narrow vein conventional shrinkage and mechanized longhole stoping. After acquiring the property in January 2007, Detour Gold Corporation initiated a comprehensive drill campaign to define the potential for a large, open pitable, low-grade gold deposit. From 2007 to present, Detour Gold has completed over 500,000 metres of diamond drilling. A technical report completed in March 2011 defined an open pit mineral reserve of 14.9 million ounces of gold, which is Canada's largest undeveloped gold reserve. The Detour Lake project is currently in development and infrastructure construction of the mine facilities started at year-end 2010, after all the necessary Provincial regulatory permits were received. Gold production is expected to commence in early 2013. Gold mineralization at Detour Lake is associated with a large scale deformation zone (Sunday Lake Deformation Zone; "SLDZ") that occurs at the contact between the 2.72 Ga Deloro Group mafic metavolcanics and the 2.69 Ga Porcupine Assemblage metasedimentary and metavolcanic rocks. The bulk of the gold mineralization is found in the hanging wall of the SLDZ, which is associated with a stockwork of auriferous quartz veins that splay from a flexure along the deformation corridor. The mineralization forms a 200-350 metres wide auriferous corridor defined over 3 kilometres along the strike of the mafic metavolcanic assemblage, from surface to at least 1,000 metres depth. The richest gold mineralized zones are commonly associated with quartz veins with a strong biotite alteration and local zones of pyrrhotite-chalcopyrite-pyrite-gold enrichment formed during the deformation of the quartz vein system.

Jan 1, 2011

By John B. Phillips

The mine is entered by a central vertical shaft, strongly timbered, and containing two compartments-one for the passenger cage, the other for the large skips bringing the ore to the surface. A man-way, for emergencies, is also provided, parallel to the shaft. The cage is a single-deck steel box, carrying about thirty persons; by means of arrangements above and below, it can also hoist and lower materials needed in the workings. Levels are run at intervals of 100 feet. In special cases, where the ore conditions warrant, sub-levels are operated, such as those at 1,113 feet and 1,123 feet (Fig. 7), which are connected by winzes with the 11 th level. One of these was pushed for 40 feet, and then abandoned because it was unprofitable to take up ore of the grade encountered. The ore between levels is removed by stoping. The drifts follow the course of the veins as much as possible, with numerous cross-cuts. Winzes, raises, connections, etc., are blasted out where needed. The main drifts are at least 8 ft. high by about 9 ft. wide. All former narrow drifts had to be widened some time ago, by ruling of the Ontario Department of Mines, to lessen the danger of accidents with cars in the small passages. Accurate plans of the under-ground workings are kept in the office, and extensive surveying is always being done underground to keep the maps up to date, measure the cubical contents of stopes, and so forth. Timber is extensively used in the construction of supports and chutes, and in the sinking of the shaft. Steel and concrete are too ex pensive to compete with timber, which 1s abundant in such sections as have escaped forest tires.

Jan 1, 1926

Agenda ? Introduction ? Inmet?s Operations and Closed Properties ? Inmet?s SECA Philosophy ? Inmet?s SECA Framework ? The Business Case for TSM ? Inmet?s TSM Reporting ? Inmet?s 2004 TSM Performance ? Opportunities for Improvement ? What Have We Learned From The TSM Process So Far? ? Summary Introduction ? Inmet has evolved into a strong TSM supporter ? Inmet is confident that TSM can be successfully and cost effectively implemented by smaller companies ? Inmet?s reporting on economic, environmental and social performance was raised significantly in our 2003 Annual Report ? a signal our commitment to good performance and improvement in these areas ? Our 2004 Annual Report has been further enhanced with the inclusion of our TSM performance

Apr 1, 2005

By George C. Coupland

"THE PRELIMINARY EVALUATION of the orebodies was computerized for tonnages and grades on a 20- by 20-ft grid. The evaluation was based on drill-core intersections over 40-ft vertical projections coinciding with the proposed bench intervals, taking the deviations of the drill holes into account. The computer print-outs gave an ore distribution and evaluation bench by bench and indicated the areas of varying mineralization. The two orebodies have a combined length of 2,200 ft. and a maximum width of 600 ft. They strike almost due north, dip about 85 degrees east and rake to the north. The computer print-outs were used to design an open pit with an over-all waste to ore ratio of 2.58:1. At the outset, the waste to ore ratio was 4:1. The pit is tear-drop shaped, with the narrow end to the south, and at the surface is 2,600 ft long by 1,800 ft wide. Ramps are 100 ft wide, with a 10% grade. The south ramp is left-handed, starts at the southeast and will continue to the bottom of the pit. A second ramp on the west and north walls runs from surface to join the south ramp at 7 bench. This ramp will handle the total pit production when part of the south ramp, from 4 bench to surface, is lost due to the underground operation. Over-all wall slopes are 53 degrees, and are laid out to avoid prominent protuberances which could relax and become unstable and potentially dangerous (Fig. 1) ."

Jan 1, 1974

By K. Robertson, K. A. Scalise, K. C. Kocsis, M. B. Teixeira

"Many deep and highly mechanized underground metal mines require cooling. In many cases, appropriate working conditions might be fulfilled by ventilation alone, but some require the implementation of cooling systems. The most common cooling systems are bulk air cooling and localized cooling. These systems are effective, but they use considerable amounts of electricity. Ground source heat pumps (GSHP) can supplement existing cooling and heating systems, while geothermal systems can cool the mines in their entirety if there are significant sources of geothermal energy are present. A major advantage of geothermal and GSHP systems are their renewability, which reduces the carbon footprint of the mine.INTRODUCTIONThe western United States has abundant alternative energy sources including a high potential for geothermal energy. Geothermal utilization is a viable energy alternative that many areas throughout the world have access to because high geothermal potentials are located near areas of volcanic activity such as along plate boundaries, mid-oceanic ridges, rift valleys and hot spots (IRENA, 2017). There is significant potential to use geothermal energy for many applications. With constantly evolving and innovative technologies being developed, an increasing number of geothermal applications are becoming feasible. The western United States is an ideal candidate for alternative energy applications due to the geothermal availability and the emergence of modern technology. This paper investigates the incorporation of renewable methods and the alternative energy possibilities of Barrick Goldstrike, located in northern Eureka County, NV and Rio Tinto/BHP Billiton’s Resolution Copper mine located in Superior, AZ.RENEWABLE SYSTEMSGeothermal SystemsGeothermal temperatures are typically defined as either high or low temperature systems(Shengjun, Huaixian, & Tao, 2011). The high-temperature reservoirs (>220°C / 428°F) are feasible forlarge, commercial production of electricity with dry stream and flash stream systems (Shengjun, Huaixian, & Tao, 2011). Low temperature systems, below 220°C (428°F) (Shengjun, Huaixian, & Tao, 2011), aremuch more difficult to use for energy production. Low-temperature reservoir heat can be harnessedthrough the implementation of a binary cycle plant. The working fluid for a binary cycle plant is eitherorganic (Organic Rankine Cycle (ORC)) or an ammonia-water mixture (Kalina cycle). Organic fluids andammonia-water mixtures have low boiling points that allow for the recovery of heat from low-temperaturesources (Eymel Campos Rodriguez, et al., 2013). The efficiency of the binary cycle plant varies depending upon the fluid, thus the proper selection of the fluid is critical for maximum energy output"

Jan 1, 2019

By R. D. Prettie

Wood preservation may be defined as the art of protecting wood from decay. In its broadest sense, however, it includes a much wider field. It might be more properly de-fined as the art of protecting wood from destructive agents, such as decay, insects, marine borers, mechanical wear, etc. The earliest data on record for the preservation of organic bodies is found in Egyptian manuscripts. The bodies which we call mummies were impregnated with antiseptics, of which the principal were natrum (sodium sesqui-carbonate), sodium chloride, and sodium sulphate. After being steeped in the solution, they were subjected to either a boiling or baking process in a bituminous preparation. The first attempts in Europe to preserve timber were made by the Greeks and Romans. They extracted essential oils from the juniper and cypress trees, and either rubbed these oils into the wood they wished to preserve, or bored thousands of small holes in the wood and poured the preservative oil into the holes. The famous statues of Jupiter and Diana were carved out of wood. The ceremony of pouring in the preservative oil by the High Priests was a religious pageant of great importance, of which there are many records.

Jan 1, 1926

By C. J. Simensen, R. Østhus, H. J. Roven, K. G. Skorpen, H. Kalager

"This work encompasses co-extrusion of alloy Al4.5Mg at the core and rapidly solidified Al4.5Mg1Ag forming the surface layer. The goal is to produce a multi-material by co-extrusion having a relatively hard surface as compared to a softer core. At the same time, work hardening in both alloys is expected to be significant due to Mg in solid solution. Precipitation hardening at 160°C is studied by applying solution heat treatments at 560°C. The hardness increased from 80 to 130 VH in the surface material after 236 h. Surprisingly, the Al4.5Mg alloy also shows pronounced aging at this temperature, i.e. from 70 to 90 VH. The relatively high solution heat treatment temperature introduces grain growth in the core, but this is insignificant for the RS surface alloy. Blisters forms at the surface and cracks follows large portions of the interface. However, the tensile ductility is significant in all conditions due to very pronounced work hardening, i.e. for the as co-extruded, T6, under- and over-aged. The elongation at fracture ranges between 40–45% and the tensile strengths 240–275 MPa. The tensile properties increase linearly with the thickness of the RS alloy, i.e. following the rule of mixtures.INTRODUCTION Al-Mg alloys in 5xxx-series are classified as non-heat treatable wrought alloys (Polmear, StJohn, Nie, & Ma, 2017). The formation of the binary ß-Al8Mg5 does not give a substantial increase in the strength of the alloys (Mondolfo, 1976). When a third element like Ag, Cu or Zn are added, G.P.?zones are formed at low temperatures and intermediate, partial coherent phases are nucleated somewhat higher temperatures and finally a ternary, equilibrium phase is formed (Auld, 1968; Cousland & Tate, 1986; Mondolfo, 1976). Both the formation of G.P.?zones and intermediate phases increase the hardness and strength of the materials. An intermediate, hexagonal T´?phase is formed in Al-5 wt%Mg-1wt%Ag, and finally the equilibrium, cubic phase (Al,Ag)9Mg5 is nucleated (Cousland & Tate, 1986; Mondolfo, 1976)."

Jan 1, 2018

By H. C. W. Bosman

"Over the past five years, contributions from geologists and mining engineers were instrumental in the successful development of MEPS. It is a system of FORTRAN programs specifically designed to be used by mining personnel to solve geological and mining problems. MEPS is a flexible keyword-driven system. Extensive error editing procedures significantly reduce the time required to proceed from problem recognition to solution. Possibly the most attractive feature of MEPS is that computer solutions may be guided or selectively modified to obtain desired solutions. Some highlights of MEPS are:1. Vocabulary that is familiar to mining people.2. Geological data storage and retrieval.3. Statistical analysis and variograms.4. Contour maps of assays and geological horizons.5. Trend surface analysis with residual evaluation.6. Ore reserve calculations.7. Open-pit mine design.8. Marginal profitability calculations on pit walls.9. Production scheduling.10. Vertical cross-section plots indicating pit outlines, ore grade contours and selected geological horizons."

Jan 1, 1973

By Gerald Blackmore

This paper discusses the present state and future trends within the coal industry, and then goes into the reasoning behind these planned trends. Such factors as marketing, costs, new mining techniques and machinery, and manpower and human resources are considered. Finally, the author refers to the effect that these trends will have on the coal industry of Cape Breton.

Jan 1, 1968

By Soumitry J. Ray

Poor visibility of powered industrial vehicles, such as forklifts, used in industry is often the cause of accidents that include pedestrians. Current standards allow up to 20 % non-visible regions for forklifts where measurement of these regions is performed by using lamps. A collaboration of research organizations, including National Institute of Standards and Technology, Georgia Institute of Technology (NIST), and Direct Dimensions, has been evaluating advanced methods for measuring a forklift operator?s visibility. These methods can potentially improve visibility standards. They can also help forklift and sensor manufacturers to determine (1) how visibility-assist sensors and algorithms can be designed and (2) where sensors can be mounted on forklifts. This paper includes explanation of visibility measurement experiments performed and results, associated language suggested to standards organizations, and a prototype design for measuring the visibility of forklifts automatically.

Aug 1, 2013