Search Documents

By M. Dupuis

In the present study, the heat balance of the Hirakud smelter aluminium reduction cell has been accurately assessed using only a surface thermocouple and a pyrometer, As it is well known that using a single linear or quadratic relationship to estimate the heat flux from the measured surface temperature does not provide the accuracy required to close the cell heat balance, this approach was not used in this study, Instead, the fundamental natural convection and radiation heat flux equations were used systematically for each measurement point, Practically, this means that the ambient air temperature and at least one ambient radiative temperature must also be known in addition to the surface temperature for each measurement point. Sometimes, the radiative heat flux could not be accurately estimated using a single ambient radiative temperature, In those cases, a more accurate estimation based on two ambient radiative temperatures and corresponding view factors has been used instead, It turns out that although at least three temperature measurements are required to estimate a single heat flux, it takes a lot less time to make those temperature measurements using a pyrometer than directly measuring the heat flux using an expensive heat flux meter, Furthermore, no loss in accuracy was detected when using this approach as the cell heat balance could be closed within 5%, the level of accuracy typical of cell heat balance assessment using heat flux meter.

Jan 1, 2004

By D. G. E. Kerfoot

In September 1945, when the Lynn Lake nickel orebody was discovered Sherritt Gordon Mines was a small copper mining company with rapidly depleting ore reserves at its single producing mine at Sherridon in the Cold Lake area of Manitoba, 100 miles north of The Pas. The company has been formed in 1927, largely through the efforts of Eldon L. Brown, a 27-year old mining engineer, with the financial backing of Thayer and Halstead Lindsley and the Gordon family. The Lindsleys were American mine promoters who had been successful in the Sudbury area, and the Gordons had extensive interests in the lumber industry in northern Ontario. Carl Sherritt, who gave his name to the company, was an American trapper and prospector who had staked the copper property and sold his interest to the new company. Carl Sherritt died in a flying accident at The Pas in 1928. The Sherritt Gordon Mine started production in 1931, shipping copper concentrate to the new Hudson Bay copper smelter at Flin Flon, Manitoba. In 1931 the price of copper was 18¢/lb. Within a year the price had fallen to 5¢ /lb and the mine was forced to close. It remained closed through the Depression years.

Jan 1, 1999

By J. Stiksma, R. Kalanchey, M. J. Collins, G. Owusu, R. Raudsepp, K. R. Buban, L. A. Barta, I. M. Masters

This paper describes the results of testwork for the treatment of Ambatovy laterite ore by a pressure acid leach process, with recovery of the soluble nickel and cobalt values as mixed sulphide intermediate by precipitation with hydrogen sulphide, and subsequent refining of the mixed sulphide to nickel and cobalt metals. These process development studies were carried out primarily in 2004, as part of a bankable feasibility study for the Ambatovy Nickel Project. The Ambatovy orebody is located in Madagascar. The mini pilot plant testwork was carried out in the Dynatec metallurgical laboratory in Fort Saskatchewan, Alberta. The results of the testwork were very encouraging, including nickel and cobalt extractions in the range of 95.5% to 97.0%, and 94.0% to 97.0%, respectively, in the ore leach step with sulphuric acid. High recoveries of nickel and cobalt were achieved throughout the remaining process steps, yielding separate nickel and cobalt metal powders with better than acceptable purity.

Jan 1, 2005

By T. Xue, A. Singhal, D. Wrana, I. Mihaylov

"At Vale's Thompson Nickel Refinery, the copper and arsenic in the nickel electrolyte are removed by precipitation using H2S, generating a sulphide precipitate containing about 40% Cu, 8% Ni, 2 to 4% As and 30% S. This residue has been typically stored in impoundment ponds within the plant site. Various options for reprocessing it have been investigated over the years. One of the options involved oxidative pressure acid leach, whereby over 95% Cu, Ni and As were extracted. More recently, an atmospheric alkaline sulphide leaching process for selective removal of 70 to 90% As was developed and mini-plant tested. After alkaline sulphide leaching, the dissolved arsenic is precipitated as stable basic ferric arsenate (BFA) with the addition of ferric sulfate, while the low-arsenic Cu/Ni sulfide is suitable for processing in Vale's operations elsewhere in Canada.INTRODUCTIONVale’s Thompson Nickel Refinery was commissioned in 1961 and currently it has the capacity to produce about 56,700 tonnes per year of electrolytic nickel as cathode slab and rounds products. A sulphate and chloride mixed electrolyte is used in the Thompson refining process and it typically contains 75 to 85 g/L Ni, 50 to 60 g/L Cl, 90 to 120 g/L SO4 2-, 25 to 30 g/L Na and 8 to 9 g/L boric acid. The main impurities in the Thompson anolyte are copper, cobalt, arsenic, iron and lead.The simplified Thompson electrolyte purification flowsheet is shown in Figure 1 (Oliver & Wrana, 2009, Goble & Chapman, 1986); it consists of precipitation of copper, arsenic and lead with H2S, followed by nickel replenishment with ground matte and acid and removal of cobalt and iron with Cl2 and NiCO3."

Jan 1, 2012

By Ursula M. Franklin

Old iron nails are one of the most common objects which entice the general public to ask questions about the history of metallurgy. There is a lot of history in old nails - history of the manufacturing industry, and social and economic history. Nails, therefore, are fine teaching tools; whether students have to acquire metallurgical skills or explore the structure and properties of wrought iron, whether they want to look into the history of inventions and the development of machinery, studying nails tells a story better than any teacher or any book. I have used this approach often and the following note is based on several student projects, particularly the work of Carmina Herrero and Vicky Marchant. Nails, those essential metallic fasteners, have long been with us. Their size, shape and design is basically a compromise between the makers' ability to control and manipulate material and the demands of the intended application. There were copper and bronze nails in antiquity, but in this paper I want to deal only with iron nails. In Rome, iron nails were common, and Cleere carried out the fine metallographic investigations on a large stock of nails recovered from a Roman fort site in Scotland. Those nails were hand forged; sorting them at the site on the basis of length, shape of head and shape of shank (in cross section) indicated that there seemed to have been some nail standardization. It appears that the Roman smiths used a series of heading dies starting with a 1/s-in. size. Each successive size increased by approximately 1/16-in. The metallographic inspection of the microstructures of the nails showed that the smaller nails were made in the one operation; i.e. both the tapering and the formation were accomplished on the heated rod without reheating. However, in the case of the larger nails, the nail had to be reheated for the tapering after the head had been forged. Most nails were tapered on all four sides of the shank and the shanks were square in cross section; only one group had rounded shanks. Most heads were flat disks, but in one group the heads were pyramids and another group had conic heads. Figure 1 shows the procedure used to produce the pyramidal heads. Obviously, Roman nail making was sophisticated and each nail design was meant for a particular use.

Jan 1, 1999

By C. Anderson, H. Huang, P. Miranda, E. Dahlgren, I. Chandra, M. Jeffrey

The latter part of the 20th century saw great advances in the treatment of refractory gold ores coupled with increased reliance on the use of cyanide for gold processing. Now, in many parts of the world, there is social pressure to limit or eliminate the use of cyanide. As well, treatment of some refractory ores or concentrates which have excessive cyanide consumption, gold cyanide pregrobbing or significant sulfide content remain difficult. This paper will outline the history of the development of alkaline sulfide leaching as an ancillary process to nitrogen species catalyzed (NSC) pressure leaching. Electrochemical fundamentals and the applicable thermodynamics of the alkaline sulfide hydrometallurgical system will be outlined. As well, examples of refractory gold recovery with alkaline sulfide hydrometallurgy such as an arsenopyrite gold concentrate application, a chalcopyrite gold concentrate application, a pregrobbing gold ore application, and a cyanide consuming gold ore application will be delineated in this paper.

Jan 1, 2005

By P. K. Kaiser, D. D. Tannant

"A support system for large ground convergence conditions or burst-prone ground must contain holding elements (rockbolts, cable bolts, etc.) that are strong yet capable of sustaining large deformations, i.e., they must absorb as much energy as possible. Steel wire rope anchored in a borehole by a friction bolt provides these desired yield characteristics if the frictional anchorage is placed deep enough into the rockmass, i.e., in non-yielding rock or beyond the expected depth of rock ejected during a rockburst. Pull-out tests were conducted on wire ropes anchored by inflated Swellex bolts to assess the feasibility of this support concept. The test results demonstrate that a Swellex bolt generates a frictional anchorage that allows the wire rope to slide at high loads and to absorb significantly more energy than either a Swellex bolt alone, or a cement-grouted cable.The rope/friction bolt combination can be engineered to provide the desired energy absorption and allowable deformation by varying the installed lengths of the friction bolt and the rope. For yielding rope support, the contact length between the rope and Swellex bolt must be short enough to ensure that the rope can slip well before its tensile capacity is reached. A safe maximum overlap length is about one metre for the wire rope used in this testing. When used as support in the backs of drifts, a swaged button on the ropes end must be used to ultimately mobilize the full rope capacity thereby protecting against gravity-driven falls of ground."

Jan 1, 1995

By Dougla McDonald, Richard Poulin

"Most mine managers in Canada today will agree that one of the keys to mining efficiency and productivity is their human resources. A5 a result, many mines develop some sort of incentive designed to tap their employees' capabilities to the fullest extent. Historically, the most common plans used have been ""piece-rate"" plans, where individual or small groups of miners are paid a financial bonus based on some measure of their productivity. Recently, however, incentive plans that take a more team-based approach have been developed in some Canadian mines. One such plan will be defined in this paper, and its popularity in the industry today discussed.Gainsharing PlansThere are two primary components to a gainsharing plan. The first is a cash incentive, which is paid to all employees and based on factors that are highly correlated with employee productivity, and key to the profitability of the mine. For example, the typical gainsharing cash incentive is based on the cost/unit of metal produced. Management (in consultation with employees in some cases) will establish the budgeted cost per tonne, and any savings in this amount is shared between the company and the employees. The second is a management philosophy and associated communication network, which is designed to foster an environment that encourages information exchanges, communication, participation, and trust between employees and management. The typical gainsharing communication network consists of two tiers of committees. The first, operational committees, include all employees working in the same department or departments which frequently interact. The employees meet monthly with management personnel to discuss problems encountered and brainstorm for solutions. In most cases, these committees will nominate a person in the group to structure the meeting to maximize its efficiency. The second, the screening committee, is a single group consisting of representatives from the various operational groups, whose primary job is to ensure that the plan is effective, and the objectives and results generated by the plan remain consistent with the mine objectives. In short, gainsharing plans tell employees that their bonus depends upon performance and then gives them the opportunity and incentive to affect that performance. The opportunity is provided by a communication network and positive management practices, and the incentive comes in the form of ""intrinsic"" rewards of participation and the ""extrinsic"" rewards of the bonus payments. Figure I will clarify the relationship between the intrinsic and extrinsic rewards."

Jan 1, 1995

By Jiuhua Xu, Shuiku Jia, Weiren Sun

"Abstract -The Jinqingding gold deposit, situated in the east Jiaodong Peninsula of Shandong province, is typical of the pyrite-quartz vein gold deposits in the Muping-Rushan gold belt of China . The gold deposit is controlled by a great NNE fracture zone and is composed of several lenticular orebodies within the fracture zone occurring in the Kunyushan granite massif. The Kunyushan granite massif was formed by the replacement of the Archean Jiaodong group.The main minerals associated with gold are pyrite, chalcopyrite, galena and sphalerite; the gangue minerals are dominated by quartz, sericite, microcline and calcite. The mineralizing event can be divided into four stages: (1) pyrite-quartz; (2) quartz-pyrite; (3) siderite-polymetallic sulfides; and (4) calcite-quartz. Gold occurs mainly as native gold and electrum in stage 1 and stage II. There are some evident differences between pyrite from major stages of gold mineralization and that from minor stages; these include differences in crystal forms, size and composition of fluid inclusions.Wallrock alterations consist of sericitization, silicification, pyritization and potash-feldspar alteration. Five alteration zones can be distinguished from unaltered granite (zone 0) to vein lodes (zone IV). Au and Ag increase rapidly from zone 0 to zone IV, Cu increases continuously, while Pb and Zn increase slowly. R-type geological factor analysis indicates that the Au, Ag, Cu, Pb and Zn bear a close relationship to wallrock alteration."

Jan 1, 1994

By O. B. Horne, R. O. Morgan, C. E. Anderson

"Air-photo interpretation and photogrammetry are two of the most effective and versatile tools available to the petroleum industry. The techniques have proven successful in providing solutions to many of the problems encountered in the design and construction of oilfield projects.Although most technical personnel are aware that air-photo interpretation and photogrammetry are useful in the selection of routes for roads and pipelines, few realize the true scope of the techniques or the wide variety of areas in which they are applicable.This paper briefly describes the principles involved, and reviews a number of typical applications of particular interest to petroleum companies. Excessive detail is avoided, rather the emphasis is placed upon the wide spectrum of possible applications. It is stressed that on-the-ground examination generally is a necessary adjunct, and that there are certain limitations to the techniques discussed.Properly applied, however, air-photo interpretation and photogrammetry can offer significant advantages in terms of time, flexibility, secrecy and economy."

Jan 1, 1968

By M. A. Vasina, I. A. Matveeva, E. A. Naumova, V. V. Doroshenko, N. A. Belov

"Using the calculated (Thermo-Calc software) and experimental methods (SEM, TEM, EMPA, DSC, XRD, etc.) the phase composition, structure and hardening of aluminium alloys of the Al-Ca-Zn-Mg system were studied in the following range: 2. 5%Mg, up to 10% Ca, and up to 14% Zn (wt%). Fragments of this quaternary phase diagram in the aluminium corner were constructed, including the liquidus surface, as well as some vertical sections. It was shown that the relatively large amount of zinc enters in the Ca-containing phase, which formula can be described as (Al,Zn)4Ca. An increase of Zn content leads to formation of Al4Ca primary crystals at lower concentrations of calcium. The eutectic (Al)+(Al,Zn)4Ca has a fine structure and aluminide particles are capable to spheroidization during the heat treatment at temperature 500 C. The maximal level of hardness observed on calcium containing alloys was higher than 200 HV, what gives the reason to expect good strength properties. With an example of an Al-9% Zn-2,5%Mg-3,5% Ca model experimental alloy based on the (Al)+(Al,Zn)4Ca eutectic, a principal possibility of manufacturing thin rolled sheets was demonstrated.INTRODUCTION Aluminum alloyed with calcium was first studied in 1970-80s by such authors as Piatti (1976), Moore (1978, 1980), Il'enko (1985), Swaminathan (1990), and Perez-Prado (1997) as superplastic materials. In particular, the alloy systems Al-Ca-Zn were studied (Il'enko, 1985, Swaminathan, 1990, Perez-Prado, 1997). For some time there was no new published works concerning the aluminum-calcium alloys. During the last years many works were published dedicated to the calcium alloying of magnesium alloys (Kim, 2011; Xu, 2011; Aljarrah, 2008; Bakhsheshi, 2014). This urged the authors (Belov, Naumova & Akopyan, 2016) to start studying cast and wrought aluminum-calcium alloys for construction (2008–2014). There is almost no information in the literature concerning triple and more complex diagrams of the aluminum-based system states with calcium and other elements. In recent work, parts of the state diagrams are plotted for the aluminum angle zone: Al-Ca-Mg-Sc (Belov, Naumova & Bazlova, 2016), Al-Ca-Ni-Sc (Belov, Naumova & Bazlova, 2017), Al-Ca-Si-Sc (Belov, Naumova & Akopyan, 2017) and others. Special attention was paid to the study of the system Al-Ca-Zn-Mg (Naumova, 2017). Based on this system creation of advanced extra-high tensile alloys is planned. Wrought extra-high tensile alloys series 7??? based on the system Al-Zn-Mg-Cu are well studied."

Jan 1, 2018

By L. L. Sirois

Because segments of the Canadian mineral-based economy are dependent totally or in part on foreign sources of certain minerals, their well-being may well be affected by inability to obtain these minerals. Where such dependency exists, it is therefore important that contingency plans be available to counteract possible price increases or lack of supplies by means of technology, developed well in advance of any pending crisis . Canada is vulnerable to possible future real or artificial shortages of certain foreign-produced mineral commodities, and science and technology can provide information for the development of policies for counteracting efforts by foreign exporters to control prices or limit supplies.

Jan 1, 1977

By Sakellariou M., Ferentinou M.

Determination of the nonlinear behavior of multivariate dynamic systems often presents a challenging and demanding task. Therefore, complex geomechanics systems are an ideal area for the application of intelligent methods. Often the physical problem is controlled by nonlinear equations, conveying to the use of neural networks. Hudson, (1992a), aiming at efficient engineering modelling and design, introduced and developed Rock Engineering Systems (RES) approach, through the implementation of generic interaction matrix GIM. This approach has been used for a wide variety of rock engineering and other problems, resulting in many case studies available, which illustrate the application of RES to rock engineering problems. Considering the spectrum of the coding methods for the Generic Interaction Matrix, we suggest an objective coding approach. Among the five proposed coding GIM methods, the coding method according to the slope of Pi and Pj relation is relatively accurate, but it might be difficult or impossible to establish or estimate the exact relation of Pi vs Pj for most of the variables involved within a rock engineering system. Self organising maps, are a special type of unsupervised artificial neural networks, which can learn from complex, multidimensional data, and transform them to visually decipherable clusters. The proposed, coding of the GIM, is performed through the combined use of scatter plots produced through, (SOM), and the coding according Pi vs Pj slope. Naghadehi et al., (2013) constructed a database of worldwide experience, in open-pit mine slope stability, the selection of the principal factors was based on Hudson (1992a) who proposed an ‘atlas’ of factors affecting the stability of rock slopes. Slope classification was performed according to status of stability. The rating of the GIM matrix was completed, coupling scatter matrix produced by SOM training, and Pi vs Pj slope plot. Results refer to the identification of clusters, according to status of stability within the original multivariate data set, and the rating of the principal factors according to the dominance and interaction intensity within the open pit mines RES.

Jan 1, 2015

By H. A. Hamza, J. Visman

"This is a report on the combined application of ""long-chain"" flocculants and classifier cyclones in the field of slimes treatment, with emphasis on the simultaneous thickening and clarifying of industrial effluents, at low cost. The principle of the process described below involves: (1) the formation of small floes of relatively great strength, by sequential dispersion and conditioning, with average floe size of about 1501 microns; (2) the floes being of sufficient strength to withstand the shearing forces operating within a cyclone and consequently behaving as solid particles with an equivalent diameter (Stokes) that exceeds the size cutpoint of the classifier cyclone; (3) the removal of flocculated solids by means of a classifier cyclone the size cutpoint of which permits effective separation of these solids from the water. Results of test work to date indicate that a broader use of cyclones in industry is possible with the above types of flocculants because the submicron particles and colloidal material are readily collected and clear water is produced, with the attendant advantages of compact construction and low cost that are characteristic of centrifugal separation. The process generally permits classifier cyclones of medium throughput capacity (e.g. 12-in. diam.) to be used for clarifying effluents that contain minus 10-micron particles."

Jan 1, 1973

By Jing Li, Weiqiang Lai, Joe Zhou, Jiezhen Ma, Shuibo Chen, Ashele Copper Company, Feng Gao, Guofu Feng

"Copper-zinc ores often contain gold and silver, which can be recovered into copper concentrate by flotation as by-product. The challenges for operations that produce copper, zinc, gold and silver are the separation of copper and zinc and the low grade of precious metals. Ashele copper-zinc ore in north China contains 2.38% Cu, 0.69% Zn, 0.21 g/t Au and 18.10 g/t Ag and the plant produces copper and zinc concentrates, with gold and silver being recovered into copper concentrate. Copper occurs mainly as chalcopyrite and Zn occurs as sphalerite. Copper is well recovered with a recovery of over 94%. However, the recovery of Zn is substantially low (around 50%) due to fine grain size of sphalerite. In addition, gold recovery is much lower than expected and only 33% of gold in the flotation feed was recovered. The grade of gold in copper concentrate is also lower than the required payable grade (1.0 g/t). To determine the cause for lower Zn and Au recoveries, a plant survey program was conducted on the operation. The information acquired shows that the loss of Zn was mainly in the copper concentrates (accounting for approximately 38% of the head assay); of which, 24% was liberated, 8.5% was associated with chalcopyrite and 4.6% was associated with pyrite, indicating that the separation of copper and zinc was the main cause for the Zn loss, with liberation being the second cause for Zn loss. Future effort in improving Zn recovery should be focused on the separation of zinc from copper. Gold in the ore occurs as both microscopic gold and submicroscopic gold, accounting for 36% and 64% of the head assay, respectively. Microscopic gold occurs mainly as native gold and electrum; it is relatively coarse with a grain size of 10 to 240 µm and a large portion can be recovered by gravity. Submicroscopic gold was mainly carried by pyrite (accounting for 38%), and to a less extent, by tennantite (15%) and chalcopyrite (10%). Gold in sphalerite is nominal (1%). It is suggested that more coarse gold and tennantite be recovered and a gold recovery increase can then be achieved to obtain a copper concentrate with over 1.0 g/t Au through flowsheet optimization. Gravity concentration should be investigated and may be worth added into the existing flowsheet to maximum the gold recovery and grade.INTRODUCTIONCopper-zinc ores containing gold and silver is a subtype of polymetallic sulphide ores. Unlike porphyry copper sulphide ores and iron-oxide copper-gold ores, this type of ores often contains substantial amounts of zinc and lead. Polymetallic sulphide ores are mainly distributed in Canada, such as at the LaRonde and Horne deposits. Other examples include Mt. Morgan in Australia and Boliden in Sweden. Globally, production and reserves from gold-rich VMS deposits account for 1370 t gold. This is equivalent to 1% of the world production and reserves, whereas the Canadian total for gold-rich VMS deposits is 870 t, representing close to 10 % of Canadian production and reserves (Gosselin & Dube, 2005a, 2005b). Flotation is the principal process for processing the copper-zinc sulphides ores, for subsequent smelting, roasting, or hydrometallurgical treatment. Oxidized copper-zinc ores can also be processed using leaching technology. For example, at LaRonde operation (a Cu-Zn-Pb ore containing 3-4 g/t Au and 60-100 g/t Ag) the flowsheet consists mainly of a copper flotation circuit and a zinc flotation circuit followed by a cyanidation process of flotation tails. The precious metals are recovered with copper concentrate, zinc concentrate and cyanidation of zinc tails via Merrill Crowe precipitation (Zhou et al., 2005)."

Jan 1, 2016

By Raymond D. Potts

"Minntac is a taconite mining, concentrating and pelletizing operation located near the town of Mountain Iron, Minnesota, U.S.A. It is totally owned and operated by USX Corporation and represents its largest source of domestic iron units. Minntac began producing fluxed pellets in 1988 and has produced both acid and fluxed pellets since then. This paper compares the acid and fluxed pellets produced at Minntac. It reviews modifications that have been made to the plant flowsheet and discusses areas recognized for improvement since the beginning of fluxed pellet production. It also comments briefly on the performance of Minntac fluxed pellets in USX blast furnaces and the future of fluxed pellets at Minntac.IntroductionMinntac was built in three steps with each step designed to produce 6 million long tons of acid pellets per year. The actual production has varied though. Figure I shows the production by year at Mirmtac. Step I began production in 1967, Step 2 in 1972 and Step 3 in 1978. Mirmtac produced 16.5 million tons in 1979 but only 3.5 million tons in 1982 when the facility was shut down for six months because of the lack of demand for pellets. Since the initial start up, Mirmtac has produced over 200 million long tons of pellets. Until 1987, all the pellets produced were ""acid"" pellets. In 1987, equipment to produce ""fluxed"" pellets was installed and tested. In 1988, full scale production of fluxed pellets began."

Jan 1, 1991

By L. Tafaghodi, S. Sarbishei

"Following the depletion of nickel sulfide ores, laterites are considered as one of the main sources for producing nickel and cobalt. One of the primary steps in pyrometallurgical extraction of nickel from laterites involves partial reduction of the ore at temperatures below 1000°C. Studying the kinetics of laterite reduction provides valuable information on reducibility of nickel laterites using coal as a reductant. The present study investigates the reduction behavior of a nickel laterite by thermal gravimetric analysis and differential scanning calorimetry. Non-isothermal reduction tests and X-ray diffraction analysis were performed to find the main reactions that occur during the process. The kinetic parameters were calculated by Coats-Redfern method. The general model of simple reaction f(a)=(1-a)n was used for calculating kinetic parameters.INTRODUCTION Nickel (Ni) naturally occurs in the form of sulfide and laterite ores. Laterite ores are mainly available in tropical regions. Weathering phenomena during millions of years has led to the formation of several layers with specific mineralogy (Butt & Cluzel, 2013). The three main layers downward are limonite, smectite, and saprolite (Crundwell et al., 2011). Although laterites are the most available nickel ore resource (70%), their share in the overall Ni production is limited to 40% (Crundwell et al., 2011). The main reasons for not materializing the full potential of laterites are as follows (Ray et al., 1985): •,Laterite ores contain high water content (free and combined) which in turn results in high energy consumption of the extraction process. •,As Ni is present in the form of solid solution in laterites, physical upgrading methods such as flotation are not effective in increasing the Ni content before the extraction process. •,Extracting Ni from sulfide ores involve exothermic reactions which are beneficial due to decreasing the overall energy requirement of the process, however there is not efficient release of energy in the process of extracting Ni from laterite ores."

Jan 1, 2017

By M. J. Brodie

"The decision to proceed with mine decommissioning, generally involves a number of complex and independent factors. These factors, including potential for re-opening, legal requirements, contingent liability, asset depreciation, due diligence, and public relations are discussed in the context of the financial implications on a net-present- value basis. It is concluded that the decision to delay mine decommissioning is commonly not in the best financial interests of the mine operator. Some measures to reduce decommissioning costs and expedite the process are presented.IntroductionThe primary audience for this paper is mining executives, although it should be of interest to all professionals involved in the planning and carrying out of mine decommissioning. Historically, mines were abandoned, not decommissioned. Then, as decommissioning became required, it was assumed that salvage revenue would pay for decommissioning. During the I980s, it became apparent that mine decommissioning costs would exceed salvage revenue for nearly all sites, and that a substantial net cost for decommissioning would be realized for some sites. Throughout this period, the approach to decommissioning has evolved through the sequential addition of measures to meet the increasing regulatory burden. This has resulted in a process in which the elements of decommissioning may not be optimized with respect to each other for the most favourable net present value to the corporation. Additional considerations which are not specific to mine decommissioning, such as environmental policy, due diligence and public relations, may now come to bear on the decision-making process.This paper addresses the issue of mine decommissioning as a three-step process. The first step involves identification and evaluation of all of the issues that relate to mine closure, the most importantof which is the potential for re-opening of a mine. Assuming that it is decided that a mine is unlikely to re-open, the second step is to determine when to carry out the decommissioning work. This aspect is examined through a net present value (NPV) approach. Finally, details regarding who does the work and how the various tasks are divided up must be resolved.Every mine is a unique concentration of minerals at some specific location, hence the development, operation and closure of a given mine must be regarded as a special case. Superimposed on the site-specific considerations are the size, history and financial status of the associated corporation."

Jan 1, 1995

By James Ball

The paper describes a new type of pump and related apparatus specifically designed to dredge sea-floor minerals from very great depths. The principle of operation of the dredging system is explained, and the factors which determine the equipment size and the power required for varying mining rates and depths of water are discussed. An estimate of the capital and operating cost of a commercial-scale mining system is presented.

Jan 1, 1968

By K. Jomoto, H. Majima

"Experimental work has been attempted to find a useful criterion of comminution which can be determined simply in a laboratory. The suitability of the ratio of the square of tensile strength to Young's modulus, St2/E, previously derived from the theory of elasticity as a criterion of comminution, was examined measuring tensile strength, Young's modulus and critical height for drop-weight impact of five different rocks. However, satisfactory correlation between St2 /E and critical height has not been obtained, suggesting the necessity of further experimental verification of the representative value of Young's modulus of rocks. The plot of St2 vs. critical height, however, shows one-to-one correspondence, and this finding suggests that St• may be a useful criterion of impact crushing. Also, a close relationship was observed between st• and the energy index for tumbling mill grinding of •the sample rocks. It is confirmed from these findings that the quantity St• is a useful criterion of comminution of rocks, not only for impact crushing but also for tumbling mill grinding. As shown in the experimental part of this paper, the determination ol St with irregularly shaped specimens is simple."

Jan 1, 1972