Search Documents

By Thomas Mütze, Frank van der Meer, Gunnar Kretschmar

"The air classification of moist bulk materials is addressed in the literature insufficiently. Therefore a feasibility study investigated the influence of feed moisture on the separation efficiency expecting a reduction with higher moisture content in the feed. Two iron ore samples were characterized in terms of the nature of bonding of moisture as well as its effect on the agglomerate strength. The classification tests themselves were conducted with two dynamic laboratory air classifiers at cut sizes from 45 to 110 µm and a moisture of the feed material between 0 to 10 wt.-%. The quality of classification was assessed by split factor, cut size, separation efficiency, moisture of both products, as well as the yield of the fines as product fraction in a corresponding processing plant. An initial approach was found for a technological implementation: A sufficient drying of a moist feed can be realized simultaneously to the pneumatic transport inside the classifiers. In the present case the drying effect and dispersion intensity was sufficient to provide good separation results up to 3 wt.-% feed moisture. An additional drying step was necessary beyond 3 wt.-%.INTRODUCTIONSpecific information about the influence of moisture in air classifiers is very rare. Mostly only dry products are processed and/or drying prior to classification is recommended. Apart from the specific influence of the feed moisture a lot of literature can be found regarding air classification itself. Altogether air classification can be divided into several sub-process (Leschonski, 1977):- dosage of the feed material,- dispersing the solid feed material into a gas stream,- feeding the dispersed material into the classification zone by pneumatic conveying,- separation of coarse and fine particles, and- separation of fine particles from gas.For wet feed particles also drying plays an important role. Interesting for the present investigation are the humidity of the feed and its influence on the single sub-processes."

Jan 1, 2016

By T. Bhambhani, Mukund Vasudevan, Partha Patra, D. R. Nagaraj, P. Somasundaram

Selective Ni separation from ultramafic ores rich in serpentines has been a huge challenge in the mineral processing industry, and therefore highly inefficient. Analysis of the root causes of the challenges and consequent development of robust processing solutions were the main goals of the Cytec-Columbia. University-Vale Joint Development Program. In this context, the subject of this paper is limited to one of the key findings of this research program which is the influence of fibrous serpentines on grade-recovery characteristics. Specifically, the poor flotation behavior is characterized by an atypical reverse C-shaped grade-recovery curve.

Jan 1, 2011

By D. H. C. Wilton, W. A. Sears

"Abstract-The 682.8 ± 1.6 Ma Tickle Point Group consists mainly of rhyolite flows and tuffs with- in the Avalon Zone of the Appalachian Orogen in Newfoundland. Stratabound massive sulfide mineralization, consisting of pyrite, sphalerite, chalcopyrite and galena, occurs at the Winter Hill prospect, where a lower pyritic, Cu-rich zone and an upper Zn-Pb-rich zone are hosted by a carbonate-calc-silicate lens. At the Frenchman Head prospect, stringers of pyrite, minor sphalerite, chalcopyrite and rare galena are hosted by felsic volcanic rocks of the Tickle Point Group .Base metal ratios, metal zonations and the overall stratigraphic framework suggest that these sulfide occurrences represent volcanogenic massive to semi-massive sulfide mineralization (stringer type at Frenchman Head). As such these prospects represent the only known VMS occurrences within the Avalon Zone of Newfoundland. Pb isotope data indicate that galena from the Winter Hill prospect is less radiogenic and older than galena from Dunnage Zone occurrences, and suggest that the Winter Hill mineralization formed in an environment tectonically distinct (exotic) from the Dunnage Zone."

Jan 1, 1996

By J. J. Hussey

"Abstract-The ""Brunswick Horizon"" an informally named ore-bearing unit near the top of the Nepisiguit Falls Formation in the Ordovician Tetagouche Group, hosts the Brunswick No. 6 and No. 12 base-metal mines, as well as the former Austin Brook iron mine, in northern New Brunswick. Detailed structural analysis of the No. 6 and No.12 mines led to the prediction that a massive­ sulfide deposit may have been repeated by F1 folding along the Brunswick Horizon. A subsequent drilling program discovered the new massive-sulfide North End Zone at a vertical depth of 1100 m, 1 km north of the No. 12 underground workings. By the end of 1990, Zn-Pb-rich massive sulfides had been delineated over a strike length of 200 m and a down-dip extent of 170 m. Rock units intersected in the North End Zone are generally thinner and vary somewhat from those at the Brunswick No. 12 mine. Thinning of the hanging wall rocks may be primary, may result from attenuation along F2 folds, or may represent truncation by a thrust fault. The newly discovered sulfide zone indicates that significant potential exists for the discovery of other deposits at previously unexplored depths.SOMMAIRE-Dans le nord-est du Nouveau-Brunswick ""l'horizon Brunswick"" est le nom usuel de la zone qui contient les mines de métaux de base Brunswick No. 6 et No. 12, ainsi que l'ancienne mine de fer Austin Brook, toutes situées sur le dessus de la Formation ""Nepisiguit Falls"" dans le Groupe Tetagouche d'âge Ordovicien. Une analyse détaillée de la structure des mines No. 6 et No. 12 à permis a van Staal de prédire qu'un gîte de sulfures massifs pourrait se répéter dû à une déformation F1, au nord de Brunswick No. 12. Suite à un programme de forage, la nouvelle zone de sulfures massifs appelée le ""North End Zone"", profonde de 1100 rn, et à une distance d'un km au nord des chantiers souterrains, fut découverte vers la fin de l'année 1990, les sulfures massifs riches en Zn-Pb ont été délimités sur une longueur de 200 rn et une hauteur de 170 rn le long du pendage. Les unités de roches intersectées dans le ""North End Zone"" sont généralement plus minces et sont quelque peu différentes de celles de la mine Brunswick No. 12. L'amin­ cissement des roches pourrait être primaire ou être le résultat de l'atténuation le long des plis F2, ou soit tronqué par une faille. La nouvelle découverte d'une zone de sulfures indique un potentiel énorme pour la découverte d'autres g ""tes à ces profondeurs inexplorées."

Jan 1, 1992

By J. T. Liu, G. H. Han, W. C. Chai, Y. F. Huang

"In beneficiation process, metal ions could adsorb onto clay mineral surfaces or interact with flotation chemicals, and then result in the flotation behavior changing of desired minerals. Al(III) is the dominating ion existing in the bauxite flotation system. In this research, the adsorption behaviors of Al(III) on two silicate clay minerals (including bentonite and kaolin) were investigated by means of UV-Vis spectra, zeta potential testing and scanning electron micrograph analysis. The adsorption experiment results show that the adsorption capacity of clays for Al(III) ions increases with the initial Al(III) concentration, contact time and solution pH. There are some different adsorption behaviours for two clays. Increasing the clay concentration decreases the adsorption capacity of bentonite, while increases first then decreases for kaolin. Higher temperature favours the adsorption of Al(III) on bentonite but goes against for kaolin. The adsorption capacities of bentonite and kaolin for Al(III) respectively reach 12.48 and 0.875 mg/g at initial solution pH 5. Zeta potential results show that the adsorption of Al(III) on two clays is characterized by electrostatic attraction mechanism.INTRODUCTIONIn beneficiation process, there is inevitably a wide variety of metal ions generated from mineral crushing, mineral dissolution and water chemistry conditions. Metal ions adsorb on the mineral surfaces or interact with the beneficiation agents, affecting the flotation efficiency of desired minerals (DiFeo et al., 2001; Parolis et al., 2008; Shackleton et al., 2012; Shengo et al., 2014). Therefore, it is necessary to have a detailed investigation on the adsorption behaviour of metal ions on clay minerals.Having good ion exchange capacity and negative surface charge, the clay minerals could take up various metal ions from the mineral-water system. Bentonite and kaolin are very common aluminosilicate clays in the mineral processing system. These two clays both hold a permanent negative charge, =X- on the basal surfaces, and a smaller variable charge, =SiOH on the mineral edges (Gu & Evans, 2008; (Gu et al., 2010). Adsorption experiments are usually used to study the adsorption affinity of metal ions for clay minerals (Sen & Bhattacharyya, 2012). The adsorption of Zn(II), Cu(II) and Pb(II) onto natural bentonite showed that the adsorption amounts of metal ions increase with contact time, solution pH and metal ion concentration, but decreases with adsorbent concentration and system temperature (Sen & Gomez, 2011; Melichova & Hromada, 2013). Cr(III) adsorption on bentonite was significantly pH dependent. The adsorption process followed pseudo-second-order model and the equilibrium adsorption was consistent with Freundlich isotherm (Lollino et al., 2015). The adsorption behaviours of Pb(II), Cd(II), Ni(II) and Cu(II) onto kaolin indicated that increasing pH favoured the adsorption of metal ions (Jiang et al., 2010). The adsorption of Cd(II), Cu(II), Pb(II) and Zn(II) onto kaolin showed that an ion-exchange reaction occurred at pH<7.0 and inner-sphere surface complexes were prone to form at higher pH (Srivastava et al., 2005)."

Jan 1, 2016

By SANDVIK WHITE

The mining industry produces approximately 4-7% of global greenhouse gas (GHG) emissions. It is fundamental for mining operations to take immediate sustainable action to actively contribute to an emissions-free future for the next generations. The mining industry has traditionally relied heavily on diesel technology and transitioning to more sustainable solutions requires change management to drive cultural acceptance and new product development. Sandvik was interested to find out the lifetime emissions of a single drill rig and to compare similar application diesel and BEV drill rigs with same use profile to each other. That led the calculation and pondering towards comparing different countries and mine sites as well

Jan 1, 2023

By J. Guha, D. Racicot, S. Peloquin, F. Lange-Brard, S. Bureau, A. Tremblay

The Devlin copper deposit consists of a flat-lying vein and a network of steeply dipping mineralized veinlets hosted by leucotonalite of the Chibougamau Pluton. Most of the vein is enclosed in a hydrothermal breccia zone which has been superimposed on a primary igneous breccia formed during the emplacement of the leucotonalite unit. This igneous breccia contains cognate fragments as well as fragments of the Dore Lake Complex, host rock to the pluton, set in a leucotonalite matrix. The hydrothermal breccia is formed of fragments of leucotonalite and the earlier breccia set in a matrix of finely comminuted rock variously altered in a roughly zonal arrangement. The major ore-bearing structure is the tabular flat-lying vein, varying in thickness from 10 centimetres to 1 metre, with a slight dip to the northeast. Well developed fracture planes, in four major orientations, contain both sulphides and gangue minerals. These appear to be displaced by the flat-lying vein. Late movements affecting the deposit include minor vertical displacements and an east-west shear truncating the southern edge of the vein. Widespread selective alteration of the leucotonalite, followed by multiple alteration veining stages characterize the deposit. Fluid inclusions associated with the mineralization indicate low temperatures, variable salinities with a variety of daughter minerals, and a vapour dominated phase. The fluid shows evidences of boiling at shallow depths. The sequence of events envisaged for the Devlin deposit is a primary brecciation during emplacement of the leucotonalite unit with widespread selective alteration possibly during the cooling stages followed by hydrothermal brecciation and late stage fract uring producing the vertical fractures and the flat-lying vein. From the alteration characteristics and the fluid data it is inferred that the Devlin deposit is the near-surface expression of a porphyry system.

Jan 1, 1984

By N. Parnian

"Carryover of caustic soda (NaOH) in the steam path caused catastrophic failure of superheater 304H stainless steel tubes in a steam generator and led to an unexpected shutdown after just five months of continuous service of petrochemical following the start of production. The cause of the failure was studied, with a focus on the formation of sigma phase in the weld joint and effect of caustic embrittlement on stress corrosion cracking (SCC). The cracks were examined at the seam weld, heat affected zone (HAZ), and Ubend areas. Hardness was measured for the base metal, HAZ, and weld metal, and microstructures were examined using optical microscopy and scanning electron microscopy (SEM). Crack initiation is attributed to gouging on the precipitated carbide at the HAZ and also the formation of sigma phase in the weld metal, as shown by energy dispersive X-ray (EDX) analysis. In addition, cracking was propagated by caustic embrittlement because of residual stresses and hammering. Finally, the characteristic feature of fracture was illustrated by SEM fractography, and consists mostly of intergranular SCC and some quasicleavage transgranular. INTRODUCTIONThree key factors are needed for the initiation and propagation of intergranular stress corrosion cracking (IGSCC): a susceptible material, a corrosive environment, and sufficient stress. Although austenitic stainless steels are susceptible to sensitization and IGSCC, they are widely used in boiler and superheater tubes because of their high corrosion resistance, high oxidation resistance, acceptable mechanical characteristics at elevated temperatures, and low cost.Sodium hydroxide is injected to neutralize acidic constituents in the steam path, but caustic can concentrate in boiler tubes and attack the surface metal (known as gouging) even traces of caustic in the steam can deposit on surfaces and cause local concentrations of several percent (ASM handbook, 1992). Not only sensitized grains but also sigma phase formed in the weld metal can initiate caustic cracking. In this research, the cause of the failure of 304H stainless steel superheater tubes in a methanol petrochemical plant in Iran was studied with a focus on the effects of caustic embrittlement on IGSCC."

Jan 1, 2012

By McGill Metals Processing Centre, S. Chang, L. Calzado, X. K. Cao, C. H. Hsin, M. Isac

"Due to the increasingly stringent cleanliness requirements for final steel products, there has been a growing interest in the possible use of micro-bubbles for the removal of inclusions with diameters smaller than ~50µm, present within the steel passing through a steelmaking tundish. However, several technological barriers have prevented the adoption of this technique in industry. These are related to a) the generation of micro-bubbles in liquid steel, b) the measurement of bubble size distributions, and c) the optimization of bubble injection conditions to create micro-bubbles. In the present study, a novel Aqueous Particle Sensor (APS) system was developed for the in-situ, on-line, detection of micro-bubbles in water, generated by a newly designed full-scale ladle shroud, located at McGill Metal Processing Centre (MMPC). Measurement results from the sensor were validated against bubble size data collected through a high speed camera and post-processed through the commercial software, Image J.Control variables and orthogonal experiments were designed to assess the dependence of average micro-bubble sizes and bubble size distributions on key experimental parameters. Those chosen were the air inlet flowrate, the distance of the gas injection port from the slide gate, and the number of injection ports used. The investigation demonstrated that the APS system can be successfully adapted to detect micro-bubbles up to ~800 micron diameters. Using this novel sensor, it was shown that multi-port injection using low air inlet flowrates, closer to the slide gate, were useful in forming small micro-bubbles within the flow through the ladle shroud. The results from the APS system were compared and validated against data resulting from an optical technique. INTRODUCTIONModern industry expects increasingly stringent cleanliness requirements for final cast products. Therefore, the numbers and sizes of inclusions need to be strictly controlled in steelmaking operations. Thus, the cleanliness of steel products depends on the amount, morphology and size distributions of nonmetallic inclusions in steel (Zhang L. & Thomas B., 2003). Since large, deep, tundishes provide longer nominal residence times for liquid steel passing through it to the exit SEN’s, this can provide the ideal place to separate inclusions, and bubbles can assist by removing help attach inclusions and float them to the top surface."

Jan 1, 2016

By C. Allen, V. Hensel, J. S. Stachulak

"Vale has been actively evaluating new technologies to curtail diesel emissions. This paper discusses the selection, installation, operation, and evaluation of the MANN+HUMMEL SMF®-AR diesel particulate filter system to reduce diesel particulate matter emissions in underground mines. The system uses a sintered metal filter element, an iron fuel-borne catalyst with an onboard dosing system, an electric heater that uses onboard power, and a sensor-based control unit. More than 6,000 h of testing demonstrated that the system represents a breakthrough in the successful control of soot emission from light-duty vehicles with differing soot emission levels, exhaust temperatures, and duty cycles.RÉSUMÉ La compagnie Vale évalue activement de nouvelles technologies pour réduire les émissions de diesel. Le présent article discute du choix, de l’installation, du fonctionnement et de l’évaluation du système MANN+HUMMEL SMFMD-AR de filtrage des particules de diesel pour réduire les émissions de particules de diesel dans les mines souterraines. Le système utilise un élément filtrant en métal fritté, un catalyseur à base de fer dans le carburant avec un système de dosage intégré, un élément de chauffage électrique qui utilise l’alimentation incorporée et une unité de contrôle avec un capteur. Plus de 6 000 heures d’essais ont démontré que le système représente une avancée pour réussir à contrôler les émissions de suie des véhicules légers avec différents niveaux d’émission de suie, différentes températures d’échappement et différents cycles opératoires."

Jan 1, 2015

By T. Donkin, B. Patterson, M. I. Guthrie, J. T. Ross

"The interest in the use of sensor-based particle ore sorting has increased significantly with the recent advances in the sorting technologies and higher capacities per unit. This technology has the potential to provide great value in processing lower grade ores from the mine whilst delivering higher grades to the mill as well as in upgrading waste rock into ore. Typically, the focus is on the amenability of the ore to ore-sorting and associated reductions in the consumption of energy, water and consumables. However, layout has a significant impact on the installed cost of a concentrator and the layout impacts from fitting an ore-sorting circuit into the concentrator plan need to be carefully considered. This paper examines layout considerations that play an important role in ore sorting projects. These include additional crushing and screening requirement, transportation of the rejected material back to the waste stockpile (mine fleet requirements) and effects on concentrator footprints.INRODUCTION Ore sorting has been practiced throughout history with an early report by Agricola in 1556. Metallic and non-metallic minerals were extracted from rocks by laboriously breaking them with hammers and picks and hand-picking selected material with higher grade off a table. The concept has not changed but the sorting technology has evolved significantly over the last 20 years. Ore sorting is usually a dry process in which a portion of the material is rejected based on mineral properties and/or grade. The methods used for sensing ore particles cover a large range of physical properties. A variety of sensors are available that differ on the discrimination technique that is used, which include: photometry, radiometry, conductivity, magnetism, microwave, X-ray transparency: X-ray transparency and luminescence and UV fluorescence (Sivamohan and Forssberg, 1991; Wotruba, 2006). There are two main ore sorting techniques: particle ore sorting and bulk ore sorting. According to Nadolski et al (2018), the potential for sorting is determined though analysis of grade heterogeneity within the orebody (greater heterogeneity represents more opportunity to add value to a project) at the scale of the intended sorting unit size."

Jan 1, 2019

By T. Avilez, D. Salari

"The economics of developing gold deposits containing elevated levels of cyanide soluble base metals is often challenged by high cyanide consumption and increased operating costs. SART is a chemical process that enables cyanide consumed by base metals to be recovered and recycled for gold leaching. The process also provides concurrent recovery of the base metal to generate incremental revenue from the sale of high-grade base metal sulphide concentrates. Although SART was developed and successfully piloted by Lakefield Research and Teck Corporation in the late 90’s and is now a public domain technology, the adoption of SART has been relatively slow due to concerns about implementation costs and the reliability of metallurgical performance. Through extensive experience in selective metal sulphide precipitation applied to mining wastewater since 2007, BQE Water has provided process know-how, design along with operations and maintenance experience to a number of projects involving the integration of SART into various metallurgical flowsheets on an industrial scale. This paper presents the commissioning experience and operating data from a SART plant treating up to 500 m3/hr of leach solution at a heap leach operation in Mexico. INTRODUCTION One of the current trends in the gold industry globally is the increasing importance of complex polymetallic gold deposits as discoveries of large Carlin type gold deposits become increasingly rare (Sceresini, 2005). The presence of cyanide soluble copper and zinc in complex gold deposits necessitates changes to the traditional gold extraction metallurgical flowsheet. A tool available to the industry to help manage the interference of cyanide-soluble base metals in gold extraction is the SART (sulphidization-acidification-recycling-thickening) process. SART breaks the weak acid dissociable (WAD) base metal-cyanide complexes, precipitates the metals as high-grade sulphide concentrates and makes the freed cyanide available for recycle."

Jan 1, 2018

The extractive industry has the potential to impact the health and well-being of workers, families and surrounding communities. In the current environment of social performance, project planning considers that activities should be conducted in the best environmentally, socially and economically acceptable way across the development cycle (i.e. from exploration ? post-closure). In this context, health impacts of mining can be mapped and extend over the Life of the Community and can encompass worker injury and disease, exposure to communicable and non-communicable diseases, and health outcomes specific to family and community health and well-being outside the fence. To contribute to an emerging field focused on Health and the Extractive Industry, this paper reviews and compares health activities extracted from social and environmental reports published by selected major mining, oil and gas companies with operations in Australia and Canada. The objective of this review is to map corporate approaches to public health management across our previously developed Life-of-Mine within Life-of-Community (LOMLOC) framework in order to identify and compare trends and behaviour in corporate health investments across the project cycle, as well as identify the level of prevention targeted by this investment activity (i.e. primary, secondary and tertiary prevention of detrimental health impact). With the extractive industry facing ongoing rapid growth worldwide, this paper provides preliminary comparative information about corporate health spending by some companies in Australia and Canada. This information serves as a resource for minerals industry managers, civil society and regulators regarding current health management approaches in this sector.

Aug 1, 2013

By T. G. Phillips

"This paper gives an inside look at a bulk terminal and describes the preparations that must be made by a company in developing such a terminal and its position in today's traffic pattern. The following headings cover the subject material: (a) Traffic pressures, their detection and measurement, (b) position in the traffic flow -selection of site, (c) transportation connections -present and possible future routes, (d) engineering studies and costs, (e) contracts, the basic material for insured traffic, (f) financing, (g) budgetary control, (h) development of new techniques, (i) growth into new cargoes or cargo-handling methods and (j) consolidation."

Jan 1, 1968

By K. Hawboldt, J. E. Halfyard, C. Bottaro, I. A. Harrison

"The removal of elemental sulfur from leach residues derived from massive sulfide concentrates via hydrometallurgical routes has been demonstrated in a laboratory setting by converting water-insoluble sulfur to water-soluble polysulfides. The approach was applied to leach residue from Vale's nickel hydromet demonstration plant in Argentia, Newfoundland, which contained significant amounts of elemental sulfur. This technique offers an alternative treatment protocol for residues with a sulfur component not amenable to standard flotation/hot filtration processes. The practical considerations of a proposed flow sheet will be discussed including the impact of other sulfur species (e.g. thiosulfate and sulfides) and key process variables. INTRODUCTIONPresently, large scale elemental sulfur extraction from hydrometallurgical leach residue is performed by Teck Resources using a process of sulfur flotation followed by hot filtration (Chalkley et al., 1993). As mentioned, the technique proves viable for residues derived from specific concentrations - in this case zinc - whose residues constituency is primarily elemental sulfur itself. However, problems arise when this constituency is altered as happens when, for example, a mine containing one particular concentrate is mixed or replaced with a differing concentrate from a second mine. Such cases can often strain the effectiveness of current sulfur removal processes (D'Odorico, 2004). If hydrometallurgical residue containing elemental sulfur cannot be effectively treatment by flotation, the residue is stored subaqueously as is the case in some 'grass roots' hydrometallurgical plants (those not coupled with smelting operations). Hydrometallurgical processing of concentrates involving pressure leaching is becoming increasingly common throughout the mining world, the genesis of which can be found in research performed by Sherritt in Fort Saskatchewan since the 1950’s (Ozberk et al., 1995).The investigation of elemental sulfur removal by means other than flotation includes the uses of sulfide salts (NH3S or Na2S) effecting the conversion of hydrophobic elemental sulfur to hydrophilic polysulfides. The work of Kunda et al. (1974) and Olper et al. (2007) shows that elemental sulfur can be quantitatively removed from hydrometallurgical leach residue via the formation of a mixture of polysulfides."

Jan 1, 2012

By Rob Kelso

The PISCES Goals ? To conduct research and develop programs to enable and promote planetary surface exploration ? To host international tests and technology demonstrations at the PISCES Test Site. ? To promote STEM education, inspiring students by connecting Hawaiian culture to space exploration and settlement. - economic and workforce development ? To involve the commercial sector, spinning off technologies to help the local Hawaiian economy. ? To develop a full-scale, technically valid, analog lunar/Martian outpost on Hawai`i Island.

May 1, 2013

By A. Brown

THIS P APER has been pre-pared as a progress report on Mines Branch investigations into problems of ground stress in certain co al mines of Western Canada. As such, it should be considered as a companion report to the one ( 1) presented to the Mining Society of Nova Scotia in 1956 and which dealt with similar investigations in the coal mines of Eastern Canada. For the past 50 years, dynamic incidents in the form of &apos;bumps&apos; and &apos;outbursts&apos; have been occurring in the coal mines of the Inner Foot-hills belt of tl1e Canadian Cordillera. As these phenomena generally become more frequent with in-creased thickness of overburden, a limiting depth of mining of 2,500 feet has been set (2) for estimating recoverable reserves of coal. If such a view were accepted, from a long-term viewpoint very large resources of coking-grade ?coal -in a part of the continent deficient in such coals -would not be available to the nation. The terrain in which these in-6dents take place may be described in geological terms as being dominated by pronounced structure in strata ?consisting of a large proportion of highly indurated rocks. The Geological Survey of Canada has co-operated by carrying out structural studies (3) at the mines, supplemented lithological by stratigraphic observations.

Jan 1, 1958

By James H. C. Martens

Among the many interesting problems of the pre-Cambrian of the Canadian Shield is that of the origin of certain types of gneisses which are intimately associated with the granites on the one hand and with the metamorphic rocks of known sedimentary origin on the other. The observations recorded in this paper on the structure and composition of these ancient rocks found in a small part of northern Quebec may help to lead to a clearer understanding of the way in which they were formed and also constitute a contribution to the regional geology and petrography of a district for which little detailed information is available. The area considered is located near the Ashuapmuchuan, or Chamuchuan, river about 180 miles north-northwest of the city of Quebec, and therefore well within the Canadian Shield. Although most attention was devoted to the rocks along this river from the 57th to the 70th mile above its entrance into Lake St. John, a few observations on other localities to the north and northwest of that lake will be included. The field work was done in the summer of 1924 in cooperation with L. W. MacNaughton, E. S. Roberts, and B. M. Shaub, all of Cornell University. The party ascended the Ashuapmuchuan river by canoe and spent about a month near the mouth of Stacker, or Brochet, river, the outlet of the lake of the same name, returning by way of Mikoasas river. The writer wishes to express his obligation to his associates for their co-operation in the field and for their permission to publish the results. He is especially indebted to B. M. Shaub for the photographs of rock outcrops. Professor A. C. Gill g:ive many suggestions which were helpful in the laboratory study of specimens and in the preparation of this paper.

Jan 1, 1927

By K. Soga

DOWA has long been specialized in the treatment of complex massive sulfide ores from exploration through smelting. Its competitive advantage derived from ore dressing technology to dress and concentrate complex ore to various kinds of metals concentrates. With this technology, the company recovers as many as seventeen different nonferrous metals. Therefore, it is crucial for the environment management and recycling business both to recover valuable elements like gold, silver, copper etc. and to handle hazardous elements in safety. From this view point, the nonferrous metal industry has a potential to play an important role; that is "The Anchor of Recycling" or "The Joint of Recycling Loop". By utilizing these mining, smelting and refining technologies, know-how and facilities, DOWA became a leading waste treatment, soil remediation and metal recycling company in Japan. This knowledge is now being applied in China .

Jan 1, 2007

By C. Doyle, J. Brennan, C. Díaz, J. Hrepic, K. Cushnie

"In 1991/1992, INCO undertook a successful R&D program aimed at extending the lining lives of the top blown rotary converters (TBRCs)at its Copper Cliff Nickel Refinery (CCNR) and the electric furnace at INMETCO. At the laboratory scale, this effort was divided into three phases. In the first part, mineralogical work was performed on six refractories that were either currently being used to line these vessels or were considered suitable alternatives. In the second part, this mineralogical knowledge was used to help determine the compositions of slags that would not corrode the bricks at the operating temperature (1600°C) of the above furnaces. Finally, several important properties of the six refractories were measured to complete their evaluation as candidate linings. This paper reports the results of all three phases of the laboratory scale R&D work.The mineralogical work showed that rebonded fused grain magnesite-chrome (RFG-MC) bricks consist principally of periclase with minor amounts of free chromite and trace quantities of silicates monticellite and sometimes olivine. The bricks are principally held together by periclase-periclase direct bonding. Of note, the bulk of the chromite exists as exsolved precipitated blebs within the periclase grains. These likely redissolve at high temperature.Slags on the periclase liquidus coexist stably with these refractories. Examples are presented using CaO-MgO-Al2O3-SiO2 slags at~1600°C.Finally, the two refractories manufactured using close to 100% fused grain material generally outperformed the others in terms of physical properties and certainly were superior in their resistance to slag penetration damage."

Jan 1, 1997