Search Documents

By R. Siwik, N. K. Davé

"The national reactive tailings (RATS) program is a co-operative industry-government effort to develop practical techniques for closure of reactive tailings areas. This paper summarizes the RATS program objectives and areas of research, and details the Noranda/CANMET project on the Waite Amulet tailings.Geophysical and biohydrogeochemical investigations were carried out at an inactive copper-zinc mine tailings site, Waite Amulet, in Noranda, Quebec. Geophysical investigations consisted of seismic, electromagnetic conductivity and electrical resistivity surveys to determine the thickness of the layers above bedrock and to map conductivity variations within the tailings and the immediate outlying area. Biohydrogeochemical investigations consisted of installing multilevel piezometer nests to determine groundwater flow patterns and porewater chemistry, obtaining solid core samples and characterizing for physical, chemical and mineralogical parameters, and iron oxidizing and sulphate reducing bacterial counts.The geophysical survey indicated a bedrock ridge extending under the tailings from the northeastern outcrop which may act as a porewater boundary layer. The survey also indicated a 2 to 20 m clay layer underlying the main tailings dam. Preliminary results of the saturated zone porewater chemistry have indicated three major zones of high electrical conductivity varying between 1,000 to 12,000 µs and pH between 3.4 to 8. Lower pH and high metal and sulphate concentrations were obtained in a shallow zone near the water table. With depth, the concentration of metal and sulphate ions decreased and pH increased below the water table. The underlying clay layer is relatively impervious -and most of the seepage from the tailings is probably exiting from the sides of the impoundment dam."

Jan 1, 1987

The 2-4D window shown above is the base startup window which allows you to begin a new project. ??Setting up the project is the first step ??The next step is to setup the properties to be used in this project

Feb 1, 2008

By Anne-Marie Dagenais

Un recouvrement de type couverture à effets de barrière capillaire (CEBC) a été mis en place en 1988-1999 sur le parc à résidus de l?ancien site minier Lorraine situé au Témiscamingue. Depuis sa construction, la CEBC fait l?objet d?un programme d?auscultation et de suivi qui vise à évaluer son comportement hydrique et sa capacité à limiter le DMA. Des essais de consommation d?oxygène ponctuels ont également été réalisés sur le site afin de mesurer directement le flux d?oxygène traversant la couverture. Les résultats provenant des relevés de teneur en eau volumique et de succion, pour les années 1999 à 2001, montrent que les effets de barrière capillaire sont présents et que la couche de rétention d?eau demeure dans un état près de la saturation pour l?ensemble de la couverture. Les flux d?oxygène calculés à partir des mesures mensuelles sont en général inférieurs à 10 g/m2an, soit en deçà des valeurs de design de 20 à 40 g/m2an. Les essais de consommation d?oxygène réalisés sur la CEBC donnent également des flux d?oxygène du même ordre de grandeur. Les résultats obtenus de ces différentes méthodes d?évaluation concordent, et ils confirment l?efficacité de la CEBC à inhiber le flux d?oxygène et à contrôler le DMA.

Nov 1, 2002

By J. Pepin

When using alternating current submerged arc welding (SAW) to produce pipes from microalloyed linepipe steels, it is critical to balance penetration depth and deposition rates, in order to minimize the number of weld passes while still maintaining good heat affected zone (HAZ) microstructures and properties. A series of bead-on-plate (BOP) submerged arc welds were performed on X70 steel, using different waveform variable settings (i.e., balance, offset and frequency). Weld bead cross-section profile deposition and penetration areas were measured, and both Vickers hardness and Charpy V-notch impact testing were performed. Both single electrode and tandem electrode welds were evaluated.

Jan 1, 2011

By W. S. Dyer

Considerable attention has been paid in recent years to the fire-clay and silica-sand deposits of the Mattagami and Missinaibi rivers and ? to the lignite occurring in them. The fireclay especially deserves this attention; it is of first-class quality; it appears to be widespread; it is the only fire-clay in central Canada, and part of it lies not more than 20 miles west of Coral rapids, to which point steel will be laid this coming spring by the Temiskaming and Northern Ontario railway. Undoubtedly, these clays will rapidly find a place in industry. The fire-clays and the better grades of silica-sand are Mesozoic in age and have been referred to the Lower Cretaceous or Upper Jurassic. Glacial clays and sands and Palaeozoic shales also occur in the same region, but are of little economic value, and will not be dealt with in this paper. Dr. Robert Bell was perhaps the first to discover the clays, since in the Report of Progress of the Geological Survey of Canada for 1877 and 1878 he reported beds of lignite on Coal brook, a tributary of the Missinaibi river, underlain by sticky clay and overlain by glacial drift. In 1880 E. B. Borron (1) discovered an extensive deposit of white sand and clay on the east bank of the Missinaibi river, five miles below Coal brook, and in 1890 (2) he examined the deposit found by Dr. Bell on Coal brook. He recognized that the underlying clays were quite distinct from the glacial clays of the region, and suggested that they might be used for fire-brick if metallurgical operations were undertaken in the region. Somewhat later, J. M: Bell described a deposit of fire-clay and silica-sand on the Wabiskagami river, another tributary of the Missinaibi.

Jan 1, 1928

By D. R. Boyle

"The Murray Brook precious metal (Au, Ag) gossan deposit is one of nine supergene mineral deposits that have developed over polymetallic massive sulfide deposits in the Bathurst Camp of New Brunswick. Reserves consist of 1.9 Mt of gossan containing 1.53 g/t Au and 65.9 g/t Ag. The supergene zone at Murray Brook consists of six distinct units: a) altered massive sulfide, b) pyrite-quartz sand, c) massive sulfide gossan, d) disseminated sulfide gossan, e) ferruginized wallrock, and f) leached bedrock. The massive sulfide gossan constitutes the main body of economic mineralization and consists of goethite, primary quartz, secondary amorphous silica, K-Fe-Pb-As- Sb-Ag hydrated sulfate and oxide minerals (beudantite, plumbojarosite, jarosite, bindheimite, scorodite), trace cinnabar, and cassiterite of primary origin. The order of stability of sulfide minerals during oxidation was pyrite _ arsenopyrite _ galena _ Bi-Sb sulfosalts _ chalcopyrite _ tetrahedrite group _ sphalerite.Two mass balance techniques (isovolumetric and conservative element) indicate elemental depletion in gossan relative to primary ore in the order: S>Cd=Zn>Cu=Mn>Na=Ca>Fe=Al=V> Mg= K=Se=Hg>Pb>Ti>Ag>Mo=P>Ba; and enrichment in the order Au>As>Sb>Si>Bi. Tin, as cassiterite, is conservative.Mineralogic and paleomagnetic data suggest that the gossan deposit formed under a warm temperate climate throughout the Pliocene. The rate of oxidation and the compositional nature of the ore was significantly influenced by: a) the position of the primary sulfide zone in a downward moving hydrological system, b) primary sulfide composition and zonation that promoted the development of a strong electrochemical oxidation system, and c) pronounced intercalation of carbonate and sphalerite mineralization in sulfide zones, which promoted rapid development of secondary porosity, permeability and downward flow of oxygenated groundwater.During progressive oxidation and physico-chemical erosion of the gossan zone, Au was transported downward in groundwaters, probably as a Auo colloid complex, to be concentrated in the lower horizons of the gossan profile. The precipitation of Au was greatly increased in the pyrite/arsenopyrite zones. Gold concentration was multi-cyclic with continual dissolution and nucleation of the metal until final concentration in the void structures of the gossan. Leaching experiments and microprobe analyses indicate that Au is present in the gossan as submicron composite sols of Au-Ag-silica."

Jan 1, 1995

By D. R. Boyle

"Abstract - The Murray Brook precious metal (Au, Ag) gossan deposit is one of nine supergene mineral deposits that have developed over polymetallic massive sulfide deposits in the Bathurst Camp of New Brunswick. Reserves consist of 1.9 Mt of gossan containing 1.53 g/t Au and 65.9 g/t Ag. The supergene zone at Murray Brook consists of six distinct units: a) altered massive sulfide, b) pyrite-quartz sand, c) massive sulfide gossan, d) disseminated sulfide gossan, e) ferruginized wallrock, and f) leached bedrock. The massive sulfide gossan constitutes the main body of economic mineralization and consists of goethite, primary quartz, secondary amorphous silica, K-Fe-Pb-As- Sb-Ag hydrated sulfate and oxide minerals (beudantite, plumbojarosite, jarosite, bindheimite, scorodite), trace cinnabar, and cassiterite of primary origin. The order of stability of sulfide minerals during oxidation was pyrite > arsenopyrite > galena > Bi-Sb sulfosalts > chalcopyrite > tetrahedrite group > sphalerite.Two mass balance techniques (isovolumetric and conservative element) indicate elemental depletion in gossan relative to primary ore in the order: S>Cd=Zn>Cu=Mn>Na=Ca>Fe=Al=V> Mg= K=Se=Hg>Pb>Ti>Ag>Mo=P>Ba; and enrichment in the order Au>As>Sb>Si>Bi. Tin, as cassiterite, is conservative.Mineralogic and paleomagnetic data suggest that the gossan deposit formed under a warm temperate climate throughout the Pliocene. The rate of oxidation and the compositional nature of the ore was significantly influenced by: a) the position of the primary sulfide zone in a downward moving hydrological system, b) primary sulfide composition and zonation that promoted the development of a strong electrochemical oxidation system, and c) pronounced intercalation of carbonate and sphalerite mineralization in sulfide zones, which promoted rapid development of secondary porosity, permeability and downward flow of oxygenated groundwater.During progressive oxidation and physico-chemical erosion of the gossan zone, Au was trans- ported downward in groundwaters, probably as a Auo colloid complex, to be concentrated in the lower horizons of the gossan profile. The precipitation of Au was greatly increased in the pyrite/arsenopyrite zones. Gold concentration was multi-cyclic with continual dissolution and nucleation of the metal until final concentration in the void structures of the gossan. Leaching experiments and microprobe analyses indicate that Au is present in the gossan as submicron composite sols of Au-Ag-silica."

Jan 1, 1995

By M. B. Shongwe, R. K. K. Mbaya, C. K. Thubakgale, P. Mendonidis

"A low-grade nickel-bearing ore was pre-concentrated on a SB40 laboratory model Falcon Concentrator. Three size fractions, -212+125, -125+75 and -75 µm were tested with the intent to upgrade the nickel content by reducing their content of fine silica, which becomes amorphous during leaching. Separation of silica from nickel-bearing magnesium silicate minerals; hornblende, clinochlore and talc, was more efficient in the finer particle sizes, -125+75 and -75 µm, and at high G-forces. For these two size fractions, nickel was upgraded from 0.06 to 0.07%, with a reduction in silica content from 52.12 to 50.71%. Leaching of feed samples prior to pre-concentration resulted in the formation of amorphous silica, indicative of the presence of fine silica in the samples. Leaching of nickel from the -125+75 µm fraction increased with increasing G-force and feed pulp percent solids, while that of -75 µm was not influenced. The optimum nickel recovery was 15.68% to the Falcon underflow, using the feed size fraction of -75 µm, 30 G and a feed pulp solids content of 10% solids, after 120 minutes of treatment.INTRODUCTION A low-grade South African nickel-bearing ore with about 0.06% Ni was previously studied for atmospheric pressure acid leaching using sulphuric acid. The study was motivated by the continuing search for methods to treat of low-grade ores, which appear to be an increasingly important source of valuable metals as a result of a declining production from rich sulphide ores. Nickel is a base metal that is used as an alloy in steelmaking and chemical industries because of its resistance to corrosion (Haudet et al., 2015). Nickel laterite ores with grades lower than 1.50% Ni are considered to be complex ores, accounting for 70% of the global nickel reserves (MacCarthy et al., 2016). Their complex nature may be attributed to the indefinite mineralogy of these ores, in which nickel may occur in more than one mineral host. In some cases, nickel may be finely disseminated in the ore. The grade of such an ore and complex mineralogy do not justify the application of pyrometallurgical methods for extraction of nickel (Zhu et al., 2012). This suggests that there is a need for less expensive alternative methods of extraction. This study investigates the application of centrifugal gravity concentration, using the Falcon concentrator, followed by leaching to determine the effect of pre-concentration of the ore prior to extraction by atmospheric pressure leaching with sulphuric acid."

Jan 1, 2017

By K. Thuro, L. Wilfing, H. Kasling

"In mechanized tunneling, performance prediction is a crucial issue for estimating excavation costs and construction time of a tunnel project. The aim of this work is to compare the calculated parameters by penetration prediction models with the results of penetration tests during excavation by a Tunnel Boring Machine (TBM) at actual tunnel projects. This comparison helps to improve the existing prediction models (Gehring, 1995 and Rostami (Colorado School of Mines), 1997.) and to develop a new, so-called “Alpine Model” (research group ABROCK; Schneider et al., 2012).On-site penetration tests are a common tool to determine performance of a TBM in certain geological environments. During a test, the TBM is operated under defined conditions that allow comparing the results of different projects and machine types. There are two different types of penetration tests in use. The more common type, described by Bruland (1998a), is based on test drives at different thrust levels. The tests in this study are performed as start-stop-tests, meaning that the TBM starts from zero to the maximum possible thrust and reverse with slowly increasing respectively decreasing steps (Frenzel et al., 2012). To gain information about the interaction between TBM and rock mass, a detailed geological documentation including an analysis of the discontinuity pattern and laboratory testing for rock strength characterization are mandatory.Within the last year 16 penetration tests have been performed. The results are thrust- penetration curves (Figure 2) showing that up to a certain penetration rate only crushing occurs (subcritical penetration). From there the desired rock fragmentation process called chipping takes place (Frenzel et al., 2012). These two different fragmentation processes can be described best by a bilinear function as seen in Figure 3. Both, CSM- and Gehring-model, do not fit to the trend of the penetration rates determined during the excavation process as they are using potential or simple linear functions.Another parameter that has to be implemented into the new prediction model is the influence of discontinuities. In case of favorable orientation and spacing, discontinuities reduce the required thrust at same penetration rates. In contrast, unfavorable discontinuity systems can cause blocky faces and hence worse performance than predicted. Besides discontinuities, the toughness of rocks has to be taken into account when predicting the penetration as tough rocks need more energy to obtain complete failure than brittle rocks.Key advantage of these tests in comparison to existing are more data points in less time. By improving respectively extending the existing penetration prediction models with the stated parameters, the penetration prediction for TBMs can be more accurate and also wear calculation can benefit from this approach."

Jan 1, 2015

By R. C. Tait

The gold at Giant Yellowknife is intimately associated with a complex mixture of sulphides, including pyrite, arsenopyrite, stibnite, and a wide variety of antimony sulpho-salts. Direct cyanidation has never been feasible. Recovery is almost entirely dependent upon flotation, roasting of flotation concentrate, and cyanidation of calcine. In November 1958, an Edwards-type roaster and an early prototype, two stage Fluosolids roaster, were replaced by a large two-stage Fluosolids roaster of improved design. The new roaster was started at "safe" medium temperatures, but early in 1959, temperatures in both stages were gradually and deliberately lowered to determine whether continuous autogenous roasting could be maintained under exacting low temperature conditions necessary for good extraction. Operation is smooth and continuous with first and second stage temperatures controlled at 925° and 875°F respectively. Plant cyanide ex-traction compares very favourably with extraction from low

Jan 1, 1961

"Ground control research in underground coal mines has been ongoing for over 50 years. One of the most problematic issues in underground coal mines is roof failures associated with weak shale. This paper will present a historical narrative on the research the National Institute for Occupational Safety and Health has conducted in relation to rock mechanics and shale. This paper begins by first discussing how shale is classified in relation to coal mining. Characterizing and planning for weak roof sequences is an important step in developing an engineering solution to prevent roof failures. Next, the failure mechanics associated with the weak characteristics of shale will be discussed. Understanding these failure mechanics also aids in applying the correct engineering solutions. The various solutions that have been implemented in the underground coal mining industry to control the different modes of failure will be summarized. Finally, a discussion on current and future research relating to rock mechanics and shale is presented. The overall goal of the paper is to share the collective ground control experience of controlling roof structures dominated by shale rock in underground coal mining.INTRODUCTIONThe National Institute for Occupational Safety and Health’s (NIOSH) Office of Mine Safety and Health Research (OMSHR), formerly the United States Bureau of Mines, has been conducting research on ground control safety for over 50 years. The overall objective of the research is to reduce underground mining injuries and fatalities by characterizing roof conditions, improving roof support performance and application, and optimizing pillar design and mine layout. Underground mining has one of the highest fatal injury rates of any industry in the United States—more than five times the national average compared to other industries (CDC, 2012). Roof fall injuries can be severe, resulting in lacerations, bone fractures, amputations, and death. Non-injury roof falls can also be problematic, resulting in lost production, delays, blockage of primary escape routes, disruption to ventilation, and hazardous rehabilitation conditions.Coal mining is increasingly subject to more adverse geological conditions. Weak roof can be found in all coal mining regions in the United States, but there are a few geographically isolated areas with higher roof fall rates contributed to by particularly poor roof conditions, as represented in Figure 1. This figure shows that when non-injury roof fall rates are normalized to production, the Illinois Basin and Central/Northern Appalachia regions have the highest rates. These isolated regions have inherently weak roof even before mining has occurred, and this roof is easily damaged during the mining process. The weak roof in these regions consists primarily of shale. Shale can be troublesome in underground coal mining because it can appear massive but easily splits along bedding planes and is often moisture-sensitive."

Jan 1, 2015

By I. I. Betcherman

INTRODUCTION A DISTILLATION process offers one of the most effective methods of refining metals. Its use is particularly attractive in the case of reactive metals which are not readily treated by pyrometallurgical or electrolytic methods. The 1ow vapour pressure of most metals severely restricts the applicability of the disti1lation process and only one or two metals may be effectively treated under atmospheric pressure at a reasonable temperature. If operations are carried out under reduced pressure several additional metals may be effectively distilled. Table I shows the vapour pressure of a number of metals together with a value of the free energy of formation of their ?oxides. Zinc and cadmium head the list and for many years? they have .been effectively refined by distillation. Sodium, magnesium, and calcium follow in descending order, and they may be distilled readily in vacuo and with difficulty at atmospheric pressure. Sodium, which is not of great metallurgical interest, is not considered. Magnesium has recently been produced in considerable tonnages by distillation methods ( 3). This paper describes the vacuum distillation of magnesium and calcium, their separation from each other, and their separation from less volatile impurities.

Jan 1, 1951

By O'Halloran. Gerard F.

"ECSTALL MINING has installed in their plants the most modern equipment in the mining industry. At the minesite, digital blocked frequency controls are used to monitor all crushers, conveyors, ventilation equipment and pumps from underground. Distant pumping stations are monitored and controlled by radio. Modern friction skip and cage hoisting systems have been installed with static power supply designed for automatic operation. Rotary-type compressors of recent design are in service in place of the conventional reciprocating-type units. At the concentrator, the 800- and 1500-hp synchronous motors driving the grinding mills have static field excitation and pneumatic clutches, still meeting modern-day concepts, having been• installed in 1966. The maintenance work load has increased annually for the past eight years. The modern plant, with all the present-day sophistication, must have a welltrained and well-organized force of skilled workers, and a maintenance system which will supply realistic facts and guidelines. This presentation will review the relative location of plants, utilities, maintenance and services, plant maintenance control and mechanical control. It is the hope that enough information will be presented to weigh the size of the job and how the resources are utilized for controlled maintenance."

Jan 1, 1974

By D. Michaud, C. Bazin, S. Lévesque, L. Pérez-Barnuevo, H. Longuepée

In recent years, with the emergence of Geometallurgy, a great effort has been made to characterize ore resources as early and accurately as possible, to allow better design and a more efficient operation of mineral processing circuits. In this context, core logging plays an important role, since drill cores provide the first insight into the ore characteristics. However, to satisfy geometallurgical requirements, traditional core logging does not suffice. New tools and methodologies need to be developed for the automation of core logging and the acquisition of mineralogical data better related to mineral processing performances. In this paper, a methodology for the geometallurgical characterization of drill cores is proposed, based on the drill core textural patterns. Textural pattern is defined here as the macroscopic spatial arrangement of minerals. The Mont-Wright iron ore deposit (Quebec, Canada) is used as a case study. The first part of this work aimed at analyzing the potential link between the iron ores textural patterns observed in drill cores and their response to ore processing, namely comminution and concentration. Preliminary results show similar performances in terms of energy consumption and heavy liquid separation for samples showing the same textural pattern. In the second part, this work seeks to develop a methodology for the automated identification of drill core textural patterns by the application of digital image analysis and discriminant function analysis. The results obtained show that this methodology is able to discriminate between the textural patterns identified at Mont-Wright with a good rate of success. Therefore, this work lays the foundation for the development of a new drill core characterization tool, which would allow for the early prediction of the iron ore behaviour during mineral processing through the identification of drill core textural patterns.

Jan 1, 2016

By R. Q. Honaker

It has been shown that naturally hydrophobic carbonaceous materials such as coal and graphite can be selectively coagulated and separated from hydrophilic impurities without using oily agglomerants, flocculants or electrolytes. The coagulation occurs at C-potentials significantly higher than those predicted by the classical DLVO theory, suggesting that it is driven by the hydrophobic interaction. In the present work, the energy barriers for the coagulation of a hydrophobic coal sample have been calculated using the extended DLVO theory which incorporates the hydrophobic interaction energy in addition to the dispersion and the electrostatic energies. For the coagulation of minerals present in the coal, the classical DLVO theory has been used for the energy barrier calculation. The results of these calculations provide an excellent correlation with the results of a series of Selective Hydrophobic Coagulation (SHC) tests conducted with run-of-mine coal and graphite samples.

Jan 1, 2004

By M. H. Allan

"This paper presents the geographic and geological setting of Saskatchewan Power Corporation's Poplar River Mine in south-central Saskatchewan, about 8 miles from the U.S. border. Generally the mine, which is being expanded to four million tons per year, is in an extremely disturbed geological area with severe dewatering problems. The lignite coal, which is strip mined, is supplied directly to an electric power generating station by means of a 7-mile unit-train private railroad.A number of unique reclamation and socio-economic problems were encountered because of the proximity to the U.S. border and because of the lack of experience of the regulatory authorities in projects of this kind. These are described in some detail, as well as the performance of one of the largest draglines in Canada. IntroductionThe Saskatchewan Power Corporation is a publicly owned utility which has the franchise to supply electricity and natural gas to all customers within the boundaries of Saskatchewan.Saskatchewan is a province which can almost be divided in two: the populated southern portion, principally devoted to farming, and the northern portion which is mostly on the Precambrian Shield and consists of lakes, rocks and muskeg. This portion is largely uninhabited except for a number of small villages. However, in the last few years there has been considerable mineral exploration and development, notably for uranium. This has helped considerably in the diversification of the basic agricultural economy of the province.Saskatchewan consists of 251,700 square miles, 761 miles north to south and an average of 335 miles east to west. It has a population of approximately 960,000, giving a population density of four persons per square mile. The Saskatchewan Power Corporation supplies 357,249 electrical arid 221,378 natural gas customers."

Jan 1, 1982

By Cedric E. Gregory

"A study of model rectangular mine shafts has been made in the wind tunnel, with the aim of reducing air-flow resistance elements to a practicable minimum. An analysis of Table 7 shows an indicated average decrease in resistance of 28 per cent by adopting the over-all modifications involved in the configurations actually tested. Much greater reductions (up to 68 per cent) are indicated by extrapolating beyond the test results directly achieved. Intermediate partial reductions in aerodynamic resistance are shown for individual modifications, such as: (1) about 3 per cent for locating the lagging in the No. 4 (inside flush) position as against the No. 1 position - 8 per cent as against the No. 2 position - and 23 per cent as compared with position No. 3; (2) about 12 per cent for using lagging instead of steel meshwork along the divider separating the skipway from the service compartment; (3) about 14 per cent for using steel gridwork ladder stagings at 3-set intervals instead of similarly spaced wooden stagings; (4) about 12 per cent for using steel gridwork ladder stagings at 3-set instead of at 1-set intervals; (5) about 13 per cent for fitting a streamlined fairing (see Fig. 5) to the upstream face of the skipway divider. Contrary to expectations, an advantage of only 3 per cent is indicated for lagging in the inside flush (No. 4) position over the outside position (No. 1). This slight gain does not appear to warrant the cost of moving the lagging. However, if the lagging is already in the No. 2 or No. 3 position, there is an 8 and 23 per cent advantage respectively."

Jan 1, 1973

By Douglas R. Schmitt

In general, knowledge of the state of stress within the Antarctic lithosphere remains largely unconstrained due in part to Antarctica?s inaccessibility and because of the paucity of seismic focal mechanism solutions. As such, an important component of the ANDRILL project was to acquire new information on the stress directions and magnitudes within the upper crust. Extensive fracture mapping of the core and oriented ultrasonic televiewer logging were carried out to provide strong constraints on both stress orientations and the faulting regime. The first hydraulic fracturing stress determinations in Antarctica were also carried out to provide complimentary stress magnitudes. These measurements were accomplished using a wire-line transported hydraulic fracturing system consisting, essentially, of two synthetic polymer packers that were inflated to isolate the 1-m long pressurization interval. The tests were conducted at the end of the drilling and logging in a ~130-m section specially drilled below 1000 mbsf (nearly 1500 m from the rig floor) for hydraulic fractures. This zone was drilled primarily through competent, dense, and low permeability diamicts. The core fracture and televiewer logging information was used to site twenty separate measurements. Classic hydraulic fracturing pressurization records with unambiguous breakdown and fracture closure pressures were obtained in about half of the measurements. The remaining tests provided fracture propagation and closure pressures that are consistent with the classic breakdown curves, but they did not include a clear breakdown pressure and are indicative of the reopening of either natural or drilling induced fractures in the wellbore wall. The preliminary analysis of the results are in generally good agreement with the stress directions indicated by the core fracture logging and the stress regime suggested by the character of the drilling induced core fractures.

Jun 1, 2012

By Anita Marks

In 2007 Copper Mountain Mining determined that there were sufficient resources to consider reopening the Similco Mine near Princeton, BC. The mill facility that had been built by Newmont Mining in 1972 was closed in 1996 and all of the process equipment removed. The mill had been built on the west side of the Similkameen River to facilitate mining of the Ingerbelle Deposit. In 1980 construction was completed on a primary crusher and cable belt to deliver ore across the Similkameen River from the Copper Mountain deposit to the Ingerbelle mill. With the decision to restart mining of the Copper Mountain deposit, the decision was made to design and build a 35,000 tpd grinding and flotation mill near the mining operations. This paper discusses the application of historical operating data for the selection of the mills for the new grinding circuit and provides an overview of the grinding circuit design.

Jan 1, 2012

By Güney

"An investigation carried out to determine the tendency of coals to heat spontaneously in terms of time-temperature curves coupled with the resulting oxidation products in an adiabatically controlled laboratory setup is described. Tests were made at differing moisture conditions, including oxidation and also oxidation with either adsorption or desorption of water vapour on coal.From the experimental evidence, there is reason to believe that the oxidation of coal, although an important factor, is not the predominant one in the development of spontaneous heating. In addition to the temperature increase in coal and the gaseous products evolved due to auto-oxidation, the process is accelerated by adsorption and retarded by desorption of water vapour on coal."

Jan 1, 1971