Search Documents

SOFCs with thin electrolyte of two types: SDC (15um) single-layer and YSZ (5um) + SDC (15um) bi-layer were fabricated by screen printing and co-firing on Ni¬YSZ cermet substrates. Using in-situ sintered Sm0.5Sr0.5CoO3 cathode the SDC-cell shows high performance at low temperature, 1180mW/cm2 peak power density around 650°C, while the YSZ+SDC bi-layer cell generates about 340mW/cm2 at 650°C, and good performance at 700-800°C with almost theoretical OCV value. Many Zr-content micro-islands were found on the SDC electrolyte surface. The influence of co-firing temperature and thin film preparation methods on the Zr-islands' appearance was investigated.

Jan 1, 2005

By E. Heikkinen, J. Suikkanen, T. Siren, J. Valli, M. Hakala

Diametrically faced borehole breakout observations are a fairly good indication of magnitude of the secondary stresses acting perpendicular to the borehole. In cases of low in situ stresses, where borehole breakouts are not observed naturally, it is possible to increase the prevailing stress state around the borehole by increasing the rock temperature. When the temperature is increased sufficiently, thermally induced borehole breakouts will occur. By implementing the temperature increase in boreholes located at excavated tunnels, it is also possible to study the effect of the near-field stresses caused by the excavation. The near-field stress state changes as a function of borehole depth, thus increasing the information available from experiment. To study the feasibility of this proposed low cost method, a Borehole Thermal Spalling (BTS) experiment was executed in ONKALO Underground Rock Characterization Facility, in Western Finland in 2014. The first borehole pilot test with the method was conducted in ONKALO at the POSE niche in already at May 2010, with the second pilot test following in August 2010 at Äspö HRL. The major objective of the experiments was to define the trend of the maximum in situ stress component, while also providing knowledge of the in situ spalling strength of the ONKALO rock mass. The stress state in ONKALO is nearly isotropic in horizontal layer, causing problems for the use of more traditional stress measurement methods. With boreholes heated over long interval, the weakest rock parts are observed to fail, thus providing statistical confidence. For these reasons, continuous test sections have an advantage in ONKALO, compared to spatially limited stress measurement methods such as overcoring and hydraulic fracturing. The BTS experiment is conducted in 9 meter deep vertical boreholes located at the POSE niche, situated -345 m depth below the ground surface. The boreholes used within the BTS experiment are located in migmatitic granite, in an experiment area where the surrounding stress state and the rock strength are fairly well known. The prior knowledge of the stresses is favourable for the experiment, as it requires careful planning and iterations to determine the appropriate heating power domain. Too low heating power will not be sufficient to cause borehole breakout, while too high heating power causes breakout in all directions thus making determination of stress direction hard or impossible. The initial state of the borehole and induced borehole breakouts will be monitored using acoustic televiewer logging (ABI) and optical borehole logging (OBI) imaging techniques. Fracture mechanics modelling is used in planning of the experiment, also in back-analysis to link the observed breakout angle to stress state. Both the pilot test in 2010 and BTS test in 2014 resulted in similar borehole breakout direction. The results are in line with so called EDZ & VT1 stress interpretation, revealed the maximum horizontal component bearing the magnitude of 21.5 MPa, with the trend of 166°.

Jan 1, 2015

By R. Heikkilä

In this paper the utilisation of building information models (BIM) and construction automation on building sites is discussed. A lot of research has been carried out to develop new applications for using BIM to assist construction site planning, different operations and logistics. The methods of production control and management on site utilize BIM together with machine control and navigation systems. In Finland machine control systems and the automation of construction equipment is widely used in infrastructure construction. Recently similar methods have been introduced also in building construction. This paper describes some latest Finnish examples where BIM-software is used for the planning, execution and control of building construction operations. University of Oulu has studied methods and technologies to capitalize BIM-models. The research has been mainly in infrastructure construction but the activities have recently been extended to building construction. In this paper a BIM-based tower crane operation and control system is discussed as a case study. The aim of this study was to highlight the potential areas were automation can increase the crane productivity and improve site operations and logistics. The construction site managers and tower crane operators interviewed in this study were experienced in using BIM-models on site.

Aug 1, 2013

By J. Fellowes, Z. Liang, J. Robson, M. Kenyon

"Dispersoids play a significant role in the recrystallization and texture development for wrought Al-Mg-Si (6xxx series) alloys by inhibiting grain boundary motion. It is therefore important to understand the precipitation kinetics of such particles. It is the additions of Mn and Cr in Al-Mg-Si based systems that can lead to dispersoid phases being formed. These phases are currently thought to nucleate on ß’-Mg2Si via an intermediate semi-coherent precipitate. Scanning transmission electron microscopy (STEM) has been conducted to study the precipitation of a-Al(CrFe)Si and a’-AlCrSi dispersoids. Corresponding electron dispersive spectroscopy (EDS) has been used to distinguish the dispersoids. The volume fraction and size distribution of dispersoids has been measured as a function of distance across a grain. Electron probe microanalysis (EPMA) has been conducted to study the inhomogeneity of elements in the cast structure and the effect on dispersoid precipitation. Dispersoid free regions have been observed in the microstructure correlating to regions depleted in the dispersoid forming elements.INTRODUCTION Al-Mg-Si (6xxx series) based alloys are increasingly being used in the automotive industry. The primary reason is to reduce the weight of vehicles, resulting in a reduction of CO2 emissions and increased fuel efficiency. The demand for 6xxx series is predicted to increase over the coming decade. Due to the high cost and CO2 emissions produced by raw extraction of aluminium, close loop recycling of these alloys becomes a more important process. However recycling of automotive alloys can be difficult due to pick up of impurity elements such as Mn, Cr and Fe. The addition of these elements can form dispersoid particles during early heat treatment processes. Although a controlled population of dispersoids is necessary to control the grain structure during thermo-mechanical processing, a significant change to the dispersoid population due to a composition change could profoundly influence the final microstructure, affecting the final properties of the material. More research is required on the precipitation and effect of additional minor alloying elements; in order to increase the 6xxx series alloys recyclability."

Jan 1, 2018

By William Hawker, James Vaughan, Jeff Chen, Antony van der Ent

"Nickel agromining utilizes hyperaccumulator plants (“metal crops”) to extract nickel from low-grade soils, a process that yields high-grade nickel bio-ore. This feedstock is further processed into a range of nickel products. The bio-ore is relatively free of impurities that complicate the traditional processing of laterite nickel ores. In this paper, current primary nickel processing routes and proposed nickel bio-ore processing options are summarised. A novel pyro-hydrometallurgical route demonstrated at the laboratory scale is described. This process produces a precipitated nickel hydroxide product and takes advantage of the water-soluble basic compounds in the ash to minimise reagent requirements, thereby making it suitable for small-scale implementation in close proximity to the nickel farm. In this process, nickel is precipitated from the leach solution using the basic ash wash liquor. Leaching nickel from ash generated from open air burning requires strong acid and long residence times to obtain high recoveries due to its complex nature and distribution of nickel in multiple phases. This process can be improved by optimising the ashing process with respect to nickel leachability.INTRODUCTIONHyperaccumulator plants have the unique capacity to ‘biopurify’ and concentrate certain trace elements (e.g. nickel) from the soil into their biomass (Reeves 2003; van der Ent et al., 2015). Cultivating these plants as ‘metal crops’ by periodically harvesting and incinerating their biomass generates a high-grade bio-ore (Chaney et al. 1998; Li et al. 2003). This process is called phytomining or ‘agromining’ which is an emerging technology for extracting nickel from sub-economic resources (van der Ent et al., 2015). Potential near-term applications of the technology include implementation on land ahead of processing of the underlying ore-body (Willis 2015), as a mine-site rehabilitation strategy or as an alternative crop for farmers on land that is not suitable for normal food crops. In the longer term, nickel agromining could provide a significant supplement to the nickel supply chain. Critical to the success of agromining is effective bio-ore processing. Due to the unique chemical composition of this feedstock material, existing processes are not very efficient. Our current research efforts aim to develop new process options that overcome limitations of previously trialled routes. In this paper we summarise conventional nickel process routes and proposed new options for producing agromined nickel."

Jan 1, 2016

By F. J. Reichhardt

Abstract -The Molopo Farms Complex is a major, layered ultramafic/mafic, early Proterozoic intrusion which is totally covered by sediments of the Karoo and Kalahari Formations and situated in southern Botswana and northeastern South Africa. The approximately 3000 m thick, generally fine- to medium-grained ultramafic and mafic cumulates are intrusive into equivalents of Transvaal Supergroup sediments and lavas. Multiphase deformation resulted in tilting and segmentation of the Complex into individual tectonic blocks. Sr isotopes document at least two chemically distinct parental liquids which interacted in a complex manner to form an approximately 1000 m thick rhythmically layered succession which straddles the ultramafic/mafic boundary. Repeated mixing resulted in a complex cryptic layering pattern and numerous sulfide-enriched layers which contain significant PGE +Au concentrations.

Jan 1, 1994

By Graham Sim

Agenda ?The Water Challenge ?Examples from Three Case Studies ?Mine Drainage, 99% recovery ?Mine Drainage, 80% recovery ?Road Dust Control ?Technology Development ? Conclusion Global water challenges Assuring sustainable quantity Improving water quality Reducing energy consumption

May 1, 2011

By B. Erdem, N. Çelebi

An important problem associated with tandem dragline systems is that of matching the productive capability of individual draglines in the combination. In this paper, a dependence mechanism among draglines in a tandem system is described, and possible consequential problems in a poorly-matched system are defined. The rate of linear advance and the cost of stripping are determined as two major indications for an efficient operation. The proposed decision criteria and the underlying mechanism to select a synchronous couple are introduced and used in simulating tandem dragline systems. The developed model is tested on a hypothetical strip mine where pullback stripping is applied with a tandem dragline system.

Jan 1, 1999

By T. Plikas, L. Gunnewiek

Computational fluid dynamics (CFD) modeling was used to evaluate the performance and optimize the design of a potroom ventilation system in an aluminium smelter facility. The ventilation system must ensure the inflow of fresh air to the workplace by natural draft and the removal of heat and hazardous emissions generated from the pot cell process. A full-scale, three dimensional CFD model of the potroom was developed to predict the air temperature distribution and contaminant concentrations throughout the potroom for the purpose of verifying that the industrial workplace hygiene standards will be met by the proposed ventilation system design. The modeling work was used to optimize the size of the floor gratings around the pot cell and roof ventilator, as well as determine damper settings in the roof ventilator. The effects of outside air temperature and external wind on the performance of the ventilation system was evaluated to ensure the design performs adequately in response to seasonal variations in climatological conditions.

Jan 1, 2006

By Kretschmar. U. H.

Fieldwork in the Meguma of Nova Scotia and Archean equivalents shows that bedding-parallel quartz lode gold veins (LVs) commonly occur at the top of graded elastic sequences. We define a "gold cycle" (GC) by analogy with Bouma turbidites and show that most "shear zones" and "lamprophyres" correspond to the upper pelagic-pelitic (E) division. We describe GCs from Archean Chester Twp, ON; Elmhirst, ON; Bourlamaque, QC; "intrusions" and interpret them as crystal tuffs and tuff-breccias. Extensive early Archean pyroclastic volcanism is implied: the genesis of trondjhemite-tonalite-granodiorite (TTG) rocks must be re-examined. The geopetal nature and asymmetric alteration of LVs indicates genesis from sea-floor hydrothermal vents. Textures suggest that often quartz was deposited as a gel. Vent geometry (fracture, point source or diffuse seep), bottom topography and vent spacing is reflected in wade-thickness plots. GC facing directions survive metamorphism. The Bourlamaque batholith was a flat-lying sheet of quartz-feldspar-hornblende crystal tuff, and isoclinal folding has repeated one or more gold-bearing horizons. Syngenesis clarifies and simplifies LV formation with major implications for models. Exploration becomes more cost-effective. Basin analysis, whole rock geochemistry, ore lens geometry and vent spacing can be used.

Jan 1, 2011

By D. S. Flett, A. V. Tolstov, M. A. Mulagaleeva, N. V. Gudkova, A. M. Zhizhaev, V. I. Kuzmin, Institute of Chemistry and Chemical Technology SB RAS, O. A. Logutenko, V. N. Kuzmina

The complex niobium-rare earth pyrochlore-monazite-crandallite ores of the Tomtor deposit, located in the Siberian Arctic, should be considered as a new type of rare metal materials. The major valuable components of the ore are niobium, rare earth elements, yttrium, and scandium; associated components are titanium, vanadium, aluminum, and phosphorus. Because of the irregular distribution of the rare earth metals and niobium according to grain-size, the extremely finely dispersed nature of the minerals and their close interpenetration to each other, ore processing by gravitation and flotation is not successful. The processes studied for the treatment of the Tomtor ores use direct alkaline-acid leaching to open the ore. A problem in the first stage of alkaline leaching is the high aluminum content, which decreases the activity of sodium hydroxide and alkaline-earth metals, which are bound to phosphorus. Ore processing using alkaline-nitrate and alkaline-chloride leaching was proposed and investigated. The first variant was used to obtain rare earth and scandium materials and a niobium-titanium concentrate, which can be a stock material for processors who use chlorination for the processing of ores and concentrates. The second variant is a complex advanced ore processing scheme with electrochemical regeneration of the waste chloride solutions obtaining sodium hydroxide, hydrochloric acid, and chloridizing agents. Moreover trisodium phosphate is used for purification of the waste mother liquors from metal cations. The complex salt, NaAlCl4, is proposed as the chloridizing agent for the decomposition of the niobium-titanium concentrate.

Jan 1, 2016

By Wm. Snow, J. R. Wallace, E. P. Duchemin

"GeneralA NOT INCONSIDERABLE proportion of the Canadian economy is dependent on the coal mining industry. This is particularly true of the eastern portion of Canada and especially so of the ( authors') province of Nova Scotia. Much has been said about the trying economic straits of the coal industry in Nova Scotia ( 1), faced, as it is, with difficult mining problems, with considerable distance from large markets, and with •competition from other (and usually foreign) fuels. It is of particular interest, at this time, therefore, to discuss one of the larger outlets for coal -that of the production of metallurgical coke.Scope of PaperWhile the title of this paper indicates that it deals with Metallurgical Coke in Canada, the authors beg leave to treat the Canadian industry very briefly and to deal specifically with coal, •coke, and smelting problems with which they are familiar, namely, the operation of the Dominion Steel and Coal Corporation in the Sydney, N.S., area. No mention is made of metallurgical coke for use in the •many foundries in Canada or in the non-ferrons metallurgical industries.Coal and Coke StatisticsA few statistics of the total output of .Canadian coal, production of metallurgical coke, and similar figures for the Dosco holdings (Sydney area only) are shown in Table I."

Jan 1, 1955

By J. R. CAMERON

Gypsum is mined in all Atlantic Provinces except Prince Edward Island. It is generally thought to have been derived from the hydration of anhydrite in areas of minimal drainage. Late Devonian downwarping and crustal oscillation east of the Appalachian fold belt allowed the Windsor Sea to advance and retreat in a depositional trough and deposit about 1,000 m of sediments in Mississippian time, much of which were evaporites. The best areas for further gypsum development are lowland basins such as the Cape Breton Lowlands, the Hillsborough area of New Brunswick and the St. George's Lowlands in Newfoundland, all of which are already sites of gypsum quarries. Nova Scotia's gypsum is mined from the Lower Windsor Group, which is divided into subzones 'A' and 'B'; 'B' provides most of the province's gypsum production. The Atlantic Provinces gypsum industry has markets from the St. Lawrence waterway to the mouth of the Mississippi River.

Jan 1, 1984

By P. J. Le Roux

"Mining worldwide and definitely in South Africa, is constantly under pressure to reduce its cost structure so as to sustain profitability. In underground gold mines where an open stope mining method is employed, dilution often has a significant effect on the viability of sustaining profits. Target Mine practices Open Stope mining Method and it was found that in some open stopes dilution was in excess of 10%, which has a significant impact on the sustainability of the mine.Dilution in excess of 10% can result in the reduction of the recovered grade from 5,5 to 4,5 grams per ton (g/t). The reduction of 1 g/t in recovered grade results in a potential loss of about ZAR21 Million per month bases on a gold price of ZAR240 000 per kilogram. Based on Life of Mine projections the potential loss of income could be as much as ZAR3,3 Billion. A reduction in dilution would have the opposite effect. There are a number of factors which affect dilution of which falls of ground in open stopes is a major contributor. The falls of ground can be attributed to a number of factors such as beam failure as a result of a larger than normal expected roof area (hydraulic radius too large), poor ground conditions, and poor blasting. The cost of damage to or loss of trackless equipment as a direct result of the falls of ground in open stopes, is very significant. The review of financial figures has indicated that this could be as high as ZAR491 million. This combined with the added cost of transport, hoisting, secondary blasting, milling and plant treatment costs of ZAR293 results in an estimated opportunity loss of ZAR784 million.Currently there is a significant amount of data available in the mining industry which could be effectively used to develop suitable back analysis techniques but to date this has not been used effectively. If dilution can have such an impact on current and future mining ventures then the optimization of back analyses for the prediction of dilution in open stoping could assist significantly in the reduction of dilution in massive open stopes. Rockmass classifications, geotechnical information, blast techniques, blast design, the stress strain environment and hydraulic radius all have an effect on, or play a role in the evaluation of dilution. Each of these factors will be taken into consideration to ultimately determine a measurable or calculated percentage of dilution in massive open stopes.The amount of overbreak in an open stope can be determined by subtracting the planned stope volume in m3 from the actual measured final stope volume in m3, which is obtained from the CMS (cavity monitoring system). This is in turn divided by the planned stope volume in m3 to determine the percentage overbreak. The CMS wireframe is imported into the geological model and its grade re-evaluated. From this the actual percentage dilution for this open stope can be determined. The dilution obtained can result in a major reduction of recovered grade for the open stope, but can also increase the recovered grade. The latter is normally the exception rather than the rule.When analysing data from Target mine the following was achieved:• Using 11 years of data a method of measuring and predicting the percentage dilution in open stoping was developed. This took into account rock mass quality, stress-strain state, and the hangingwall hydraulic radius (size of stope hangingwall exposed).• Implementation of this prediction method resulted in a reduction in falls of ground in open stopes. The benefit of this was a reduction in the damage to mechanised equipment resulting from less falls of ground which had a positive effect on the profit margins of the mine. As a direct result the recovered grade from the open stopes increased due to the reduction in the amount of dilution.• A design criterion, Dilution Stress-Strain Index (DSSI), was developed which allows the user to calculate, with certainty, the stability of the open stope and determine if m"

Jan 1, 2015

By M. G. Stamatakis, C. Zagouroglou, C. Helvaci, J. Kanaris

"Abstract -Borate minerals, such as colemanite, ulexite and borax, have been reported in Tertiary continental basins of West Anatolia, Turkey, and Samos Island, Greece.Tuffaceous rocks interbedded with the borates are rich in authigenic silicate minerals such as zeolites, potassium feldspar and opal-CT, all of which have a genetic association with the borates. Chemical analyses of the tuffaceous rocks show variation in major elements due to the varying percentage of carbonaceous, detrital, and volcanic derived material.The volcanic activity in the vicinity of each particular lacustrine basin created ion-rich fluids from which a series of borates were precipitated under arid climate. Additionally, the saline-alkaline character of these fluids was responsible for the diagenesis of the silicic glass of the tuffaceous rocks, altering them to silicates and silica polymorphs."

Jan 1, 1993

By F Kelly

"A central composite experimental design was used to determine empirical relationships between the operating variables of a ball mill and the characteristics of the ground products. The independent variables selected for the study were the work index and size distribution of the feed material, the feed rate and the pulp density. The measured responses included product size distribution, product surface area, viscosity of pulp discharge, weight of dry solids in mill, mill time constant and emitted sonic vibrations. The ball mill was operated continuously in open circuit during each experimental run.Multivariable regression techniques were used to derive linear empirical models from the experimental results. Of the four factors studied, the grindability of the feed material significantly affected every measured response. The size distribution of the ground product was affected significantly by the feed rate and the size distribution of the feed, but not by the pulp• density. Feed throughput capacity and pulp density were significant to the viscosity of the pulp discharge, the weight of solids in the mill and the mill time constant. Significant first-and second-order models are given for the above relationships. The relation-ships between the characteristics of the sonic vibrations of the operating mill and the various dependent variables have not as yet been established."

Jan 1, 1970

By T. W. Wlodek

"AbstractThe results of research into the fatigue properties of SAE 1080 carbon steel and nickel-chromium-molylbdenum steel for mining drill rods are analysed and described in detail.The effect of water corrosion on the fatigue strength of drill rods of these two steels in the as-rolled condition has ,been investigated and the beneficial influence of shot-peening on their dry and water-corrosion fatigue strengths determined by employing the method developed previously (1).Eight S-N curves for as-rolled and shot-peened mining drill rods under both dry and water corrosion conditions have been derived and their shape and relative position are discussed. The main features relating to field performance of the drill rods are analysed.Purpose of Research and Outline of ProgrammeDRILLING holes in rock and ore by means of drill rods attached to a pneumatic drill is a basic procedure required in mining operations. Detonation of explosives placed in these holes is at present the only practical method of breaking down the rock and ore.A drilling rod is supported by its bit end in the drilled rock. Its shank end, fixed in the drilling machine, transmits impact energy to the cutting edges of the bit. On the field performance of the drill rod depend a number of basic mining operations such as sinking, drifting, and stoping. The drill rod is there-fore regarded as one of the most important tools used in the mining industry."

Jan 1, 1952

By L. E. Djingheuzian

IN 1953, Lewis (1) published an article which brought forth a great amount of discussion by grinding engineers. In his contribution to discussion the present writer (2) suggested that, for the most efficient performance of a ball mill, there must be a .definite relationship between Cn, per cent critical speed, and V p, per cent mill volume occupied by the ball charge. Later, he ( 3) was able to publish some grinding data from Wright-Hargreaves milly which appeared to bear out this contention. It is with this view to establishing a fundamental relationship between Cn and Vp that the idea of this Forum was conceived. Accordingly, a questionnaire was prepared and copies of it were mailed to over eighty Canadian mill operators. This questionnaire did not include a question on dilution on the assumption that each mill operator was using the most efficient dilution for his operation, nor was a question on efficiency of classification included since it was thought that the inclusion of efficiency of dassification in the questionnaire at this preliminary stage might render the forum discussion,. while everybody was trying to find his bearings, too unwieldy. However, it is evident that, as discussions develop, this forum will have to define a uniform method for establishing most efficient classification in grinding circuits

Jan 1, 1957

By Charles G. Kemsley

IN January, 1939, Dome Mines, Limited, purchased a few bars of an alloy drill-steel for the purpose of testing its fatigue resisting qualities as compared with those of a straight carbon-steel then in general use at the mine. A steel of the following analysis was selected: Carbon 1.00% Sulphur 0.022 Chromium 1.26 Silicon 0.17% Phosphorus 0.028 Vanadium 0.1 Manganese 0.32% Molybdenum 0.30 This steel has a tensile strength of 180,000 lb. per square inch and a Brinell hardness of 380, as compared with a tensile strength of 114,000 lb. per square inch and a Brinell hardness of 230 for the standard carbon drill steels, in the as rolled' condition. The result of this test showed that about five times as many runs could be obtained from the alloy steel before failure from fatigue. It was therefore decided to replace gradually the one-inch quarter-octagon carbon steel, then in use, with seven-eighths quarter-octagon alloy steel. In January, 1940, six machines was placed on the seven-eighths steel and this was gradually increased until now (March 15th, 1941) fifty per cent of the steel being used is alloy steel. An O'Donovan furnace is used at the Dome for heat-treating their carbon drill-steel. In this furnace, a magnet withdraws the steel when the critical temperature has been reached, and the operator then places the steel in the quenching tank. Not being able to use this furnace for the alloy steel, the management felt that some means should be developed to determine the quenching temperature without depending upon the operator's judgment of the correct 'colour'. With the assistance of the Canadian General Electric Company, a radiation-type vacuum thermocouple pyrometer was adapted to this purpose, with excellent results; in fact, with this instrument no previous experience in hardening is necessary and results are remarkably uniform.

Jan 1, 1941

By D. Moronkeji, R. Maharidge, D. A. Curry, B. J. Davis, U. Prasad, J. Franquet

"Proper shale characterization is crucial in shale gas drilling, exploration, completion and production. Unlike porous sandstone and carbonate reservoirs, the challenge with shales comes from their micro- to nano-darcy permeability ranges and the anisotropy of their mechanical and hydraulic properties. Most porosity-dependent logs are not sensitive enough to capture the true behavior of shales. Consequently, mineralogy and other strength and stiffness-related properties must be determined to characterize magnitudes and variances in shale mechanical and flow properties. In addition, these properties must pass quality assurance/quality control (QA/QC) practices to give confidence in their use in subsequent log calibrations, during geomechanical modeling, or in fracture design models. This paper presents a technique to integrate shale properties that are measured by various methods, and a methodology to perform QA/QC on the data before application.Shale properties originate from various sources, including downhole and laboratory measurements. Physical samples for laboratory testing are usually limited to a few depths. Lab tests are often costly, and replicating in-situ conditions can be difficult or impossible. In addition, results frequently show wide scatter, reflecting inherent depth variability and lateral heterogeneity. Wireline logs provide nearcontinuous data, but rarely yield direct measurements of rock strength properties. Although geomechanical and fracture models use log data, calibrating it with reliable and previously verified lab-measured properties is important. This paper presents a process to perform QA/QC on lab-measured data using various crossplots.Ten mechanical, microstructural and physical properties are graphically displayed to visually characterize shale strength behavior in ambient and in-situ conditions, whether measured or modeled statically or dynamically. These properties are often sourced from different departments. The properties are integrated but are individually subject to the previously mentioned uncertainties. Pairs of property values are crossplotted and compared with correlations from the literature or previously established with qualified data from related formations. Conformance with these correlations gives confidence in the data, whereas outliers are flagged as questionable. Repeating the process with questionable data crossplotted against other parameters for the same depth highlights the property with the greatest uncertainty. The determination of its value is investigated to locate the source of the inconsistency and establish a more reliable value. Where this is not possible, the user has a rational basis for rejecting that property value."

Jan 1, 2015