Search Documents

By Walter Nelson

Considerable thought and discussion had been devoted toward provision for increased milling capacity at the Allenby concentrator of The Granby Consolidated Mining, Smelting and Power Company operations as early as 1940. During the war, plans for the installation of an additional grindi.ng unit were formulated but were not carried out. It took considerable time after the war to prepare the mine again for its highest rate of production since, with the scarcity of men, development work had been sacrificed in favour of maximum ore shipments. In order to prepare for the expected competitive market in copper, the matter of increasing the capacity of the concentrator was again given serious attention. As ore became available in the mine and the output of the mill was increased, limitations for a satisfactory recovery were observed, due to the overloaded condition of the classifier units at the higher tonnages. From a metallurgical standpoint, the ore from the Copper Mountain mine had always been difficult to treat on account of the finely disseminated character of much of the mineralization and the difficulty of grinding to the desired fineness. This trouble has become aggravated with time as an increasing amount of wall-rock has diluted the ore and lower grade orebodies have been mined. It therefore has been, and is, the practice at the concentrator to maintain the maximum amount of reduction in size of material fed to the flotation units as is possible for the daily tonnage to be milled. This means that all the grinding units are operated for the maximum possible time, and that the classifiers are regulated to return as much feed ?as possible to the mills. The number of tons to be milled for ?the day is determined by the concentrator superintendent after ascertaining the availability of ore from the mine, the condition of the concentrator ore bins, and the need for repairs in the rolls plant. In order to maintain the tonnage des1red, hourly estimates are made of the rate of grinding by weighing the amount of ore contained on one foot of each of the belts conveying the feed to the various ball-mills, and adjustments are made accordingly.

Jan 1, 1950

Pillars are used in various forms in underground mining. For several decades pillar design has been an issue in both soft and hard rock underground mining. The major use of pillars is in room-and-pillar type mining. Pillars are critical structures in the production levels of block cave mines. With most mines leaning towards the use of block caving for ore extraction today, pillar design has become even more important. Empirical pillar design is popular. The use of numerical modeling is becoming more common in the design of underground mine pillars. A critical review of both the empirical and numerical modeling approaches to the design of underground mine pillars reveal some fundamental flaws. In general, pillar design approaches often assume the pillars are vertical, and are subjected to pure compression. Pillar failure criteria are then based on this assumption. Most papers on numerical modeling for pillar stability assessment use vertical pillars. This paper shows that where pillars are not subjected to pure compression the empirical pillar design approaches are inadequate, and that when using numerical models for the assessment of pillar performance, more care is needed in the determination of the average pillar stresses. The practice of relating field scale pillar strength to laboratory scale intact rock strength determined from conventional laboratory compression tests in empirical design equations is misleading when pillars are inclined or subjected to compressive and shear stresses. New data is added to the hard rock empirical pillar stability chart, and it is shown that it is misleading to conclude that failure of pillars with width to height ratios greater than 2.3 should not be anticipated. New empirical pillar design charts are presented for pillars at various degrees of inclination for different ko-ratios.

Aug 1, 2013

By Olav Mejia

The rising energy costs and environmental considerations in mining necessitate the development of energy-efficient copper and gold processing plants. This paper presents an analysis of technical strategies aimed at reducing energy consumption in these plants. Key approaches include the integration of advanced ore sorting technologies, High Pressure Grinding Rolls (HPGR), Coarse Particle Flotation (CPF), and high-intensity flotation. Ore sorting enables early-stage waste removal, reducing the downstream processing load and associated energy use. HPGR technology, recognized for its energy efficiency, contributes to significant energy savings in comminution circuits by reducing reliance on traditional grinding methods. CPF technology further optimizes flotation performance by enabling the recovery of larger particles, thereby decreasing the need for fine grinding and reducing overall power demand. High-intensity flotation units enhance separation efficiency and mineral recovery in a compact footprint, offering further reductions in energy consumption. Together, these technologies provide energy saving opportunities to achieve a more sustainable and economically viable processing operation. This paper evaluates the effectiveness of each method, highlighting their potential impacts on energy consumption, operational efficiency, and cost-effectiveness in copper and gold processing

May 4, 2025

By Maria Agostina Cinellu

Some aspects of the reactivity of the two different kinds of gold(III) oxo complexes [Au2(N,N)2(?-O)2][X]2 [N,N = 2,2'-bipyridine (bipy) (1), 6-alkyl-2,2'-bipyridine (bipyR) (2), R = Me a, CH2Me b, CHMe2 c, CMe3 d, CH2CMe3 e] and [Au2(C,N,N)2(?-O)][X]2 [HC,N,N = 6-benzyl-2,2'-bipyridine (bipyR') (3), R' = CHMeC6H5 a, CMe2C6H5 b] (X = BF4, PF6) have been studied. Treatment with water converts the unsubstituted bipyridine complex [Au2(bipy)2(?-O)2][PF6]2 (1) and the cyclometallated derivatives [Au2(C,N,N)2(?-O)][PF6]2 (3) into the water soluble monomeric hydroxo species [Au(bipy)(OH)2][PF6] (4) and [Au(C,N,N)(OH)][PF6] (5), respectively. These hydroxo species, likely the intermediates in the formation of the oxo complexes, are quantitatively reverted to the latter ones by reflux in anhydrous solvents. Both kinds of oxo complexes react with PPh3 to give OPPh3, the gold(I) complex [Au(PPh3)2][PF6] and the free bipyridine ligands. The reaction of the dioxo complexes [Au2(bipyR)2(?-O)2][PF6]2 (2a, 2b, 2c, 2e) with different alkenes gives the unprecedented alkene complexes [Au(bipyR)(?2-alkene)][PF6]. The styrene adduct [Au(bipyip)(?2- CH2=CHPh)][PF6] (7) (bipyip = 6-iso-propyl-2,2?-bipyridine c) has been characterized, inter alia, by X-ray diffraction analysis. Organic products arising from olefin oxidation are also found in the reaction mixture.

Oct 1, 2003

By S. R. McCutcheon, D. R. Lentz

"Abstract - The 12.1 Mt Brunswick No. 6 Zn-Pb-Cu-Ag massive sulfide deposit (New Brunswick, Canada) lies between two subaqueous felsic volcanic formations near the base of the Middle Ordovician Tetagouche Group. The footwall comprises rhyodacitic pyroclastic rocks (Nepisiguit Falls Formation), whereas the hanging wall comprises a sequence of rhyolitic flows, breccias, and hyaloclastites (Flat Landing Brook Formation), with an age difference of less than 3 m.y. The Brunswick No. 6 deposit is a proximal autochthonous deposit with a well-zoned massive sulfide body and a basal Cu zone that, at depth, develops into a stockwork stringer sulfide (feeder) system. The massive sulfides are capped sharply by a layered magnetite-chert unit that extends regionally beyond the deposit. The deposit has a keel shape (sheath) formed by the F1F2 interference pattern. The heterogeneous ductile deformation and upper greenschist-grade regional metamorphism has transposed many of the epigenetic stockwork structures and alteration within the host sequence. Hydrothermal alteration is much more extensive, both vertically and laterally, in the footwall (a few 100 m) than in the hanging wall (<100 m). Anomalies farther up in the hanging wall sequence seem to be associated with independent alteration systems related to the rhyolite domes. The least-altered footwall units exhibit keratophyric alteration (albite or adularia) and weak Mg enrichment (chlorite). More intense micaceous (sericite and Mg-rich chlorite) alteration occurs around the footwall sequence. The transposed stockwork stringer sulfides are typically composed of Fe-rich chlorite (± sericite, ± silica) with pyrite, pyrrhotite, chalcopyrite, arsenopyrite, and sphalerite. The (Fe2O3T+MgO)/(Na2O+K2O) and base metal alteration indices are the best practical lithogeochemical vectoring tools at this deposit. Sommaire - Le gîte de 12.1 Mt de sulfures massifs de Zn-Pb-Cu-Ag Brunswick No.6 est localisé entre deux formations volcaniques felsiques sous-marines situées près de la base du Groupe de Tetagouche d’âge Ordovicien Moyen. Le mur consiste en roches pyroclastiques rhyodacitiques (Formation de Nepisiguit Falls) tandis que le toit consiste en une séquence de coulées, de brèches et d’hyaloclastites de composition rhyolitique (Formation de Flat Landing Brook); la différence d’âge entre les deux est de moins de 3 m.y. Le gisement Brunswick No. 6 est un gîte autochtone proximal comprenant un corps de sulfures massifs clairement zoné ainsi qu’une zone cuprifère basale qui passe progressivement à un stockwork de filonnets de sulfure en profondeur (feeder). Les sulfures massifs sont abruptement surmontés d’une unité laminaire de chert et de magnétite dont l’extension par delà le gisement est régionale. Le gisement affecte la forme d’une quille (fourreau) résultant d’un patron d’interférence F1F2. Plusieurs des structures épigénétiques du stockwork et des patrons d’altération de l’encaissant ont été transposés par la déformation ductile hétérogène ainsi que par le métamorphisme régional au faciès des schistes verts. L’altération hydrothermale est beaucoup plus importante, tant verticalement qu’horizontalement, dans le mur (quelques 100 m) que dans le toit (<100 m). Les anomalies situées plus haut dans le mur semblent être reliées à des systèmes d’altération indépendants associés aux dômes de rhyolite. Les unités les moins altérées du mur une altération kératophyrique (en albite ou en adulaire) ainsi qu’un faible enrichissement en Mg (chlorite). Une altération en mica (séricite et chlorite magnésienne) plus intense est présente autour de la séquence du mur. Les sulfures du stockwork de filonnets transposés consistent typiquement en chlorite ferrifère (± séricite, ± silice) accompagnée de pyrite, de pyrrhotite, de chalcopyrite, d’arsénopyrite et de sphalérite. L’indice d’altération (Fe2O3T+MgO)/(Na2O+K2O) et l’indice des métaux usuels sont les outils d’exploration les plus appropriés dans ce gisement."

Jan 1, 2006

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, D. K. Fountain

"Abstract -A test survey using the MEGATEMII airborne electromagnetic system was flown over the Iso and New Insco massive sulfide orebodies in the Rouyn-Noranda mining camp, Canada. The results were compared with data from historical systems (INPUT, DIGHEM) used to discover the deposits. The historical data show that the two deposits have comparable conductances. However, the modern MEGATEMII system reveals that the New Insco deposit has a much slower decay than the Iso deposit, and it is, therefore, interpreted to be more conductive. The MEGATEMII anomaly maps provide estimates of the location, depth, dip, and strike of the two deposits, information that was not available from the historical anomaly maps. The signal-to-noise ratio of the MEGATEMII data is greater than the historical data, yielding more sharply defined anomalies. The investigations also included a comparison between 90 Hz and 30 Hz MEGATEMII data. The 90 Hz data were found to be useful for mapping the less conductive parts of the Iso body, whereas the 30 Hz data demonstrated that the New Insco body is more conductive. Analysis of height attenuation data over the Iso body indicates that the body could be seen by the MEGATEMII system if it were buried an additional 230 m deeper (in highly resistive material). On the other hand, the INPUT system would detect the Iso body only if it were buried no deeper than an additional 60 m. Tests with the transmitter turned off showed that, for this flight, the MEGATEMII system noise levels on the processed data are about 300 pT/s. Sommaire - Dans le cadre d’un projet de recherche, un ensemble de levés d’essais électromagnétiques aéroportés employant le système de MEGATEMII a été effectué au dessus des dépôts d’Iso et de New Insco, Rouyn-Noranda, Canada. Les données ont été comparées avec les réponses des systèmes qui ont découvert ces deux dépôts (INPUT et DIGHEM). Les données antérieures montrent que le dépôt d’Iso a une conductance comparable à celle de New Insco. Cependant, les données de MEGATEMII démontrent que le dépôt de New Insco a une haute valeur de la constante de décroissance, ce qui reflète une plus forte conductivité. La carte d’anomalies de MEGATEMII indique la localisation, la profondeur, le pendage et l’orientation des deux dépôts, ce que la carte d’anomalies antérieure ne montrait pas. Le rapport de signal à bruit de MEGATEMII est plus grand que celui des données de INPUT et de DIGHEM; de plus, les pics sont mieux définis. Les tests ont également permis une comparaison entre les fréquences de base de 90 Hz et de 30 Hz. Les données de 90 Hz se sont montrées utiles pour cartographier la partie du dépôt Iso dont la conductivité est la plus faible, tandis que les données de 30 Hz montrent clairement que le dépôt de New Insco est plus conducteur. Les analyses de l’atténuation du signal avec la hauteur ont indiqué que le dépôt d’Iso pourrait être détecté par le système MEGATEMII s’il était enfoui à 230 m sous la surface (dans un milieu hautement résistant). D’autre part, le système INPUT pourrait seulement détecter le dépôt d’Iso s’l était situé à 60 m de profondeur. Les tests avec l’émetteur fermé démontrent que le niveau de bruit est des l’ordre de ±300 pT/s."

Jan 1, 2006

By O. A. Carson

Introduction Although the equilibrium conditions of the copper-tin alloys have been the subject of a ?great amount of research, the equilibrium diagram is still in doubt. The first systematic investigation of the series was made in 1894 by Le Chatelier, who published a freezing-point curve. In 1895, Roberts-Austen and Stansfield published the complete liquidus and partial solidus curves, which they modified somewhat in 1897. Their liquidus as given in 1897 is essentially that accepted today (Figure 3). Haycock and Neville also published a liquid us curve in 1897. In 1898, William Campbell published a series of micrographs showing the changes in microstructure which accompanied the thermal changes of Stansfield? s diagram. The classic work on the bronze series was published by Heycock and Neville in 1903. Their diagram was based on both thermal and microscopic evidence, and is the first for this series of alloys which can be considered nearly complete. Further, it was the first bronze diagram in which any attempt was made to apply the phase rule in the interpretation of the thermal and microscopic results. That portion of Heycock and Neville&apos;s diagram covered by the present work is reproduced in Figure 7.

Jan 1, 1929

By S. Mostaghel, Fariba Azgomi, Steven Goodman, M. Oliazadeh

"It is known that copper loss to the slag phase can be in the forms of chemical dissolution and mechanical entrainment. The contribution of each mechanism to the total Cu-loss depends on different parameters and may vary significantly. To reduce emissions to the atmosphere and to shorten the converting cycle, most industrial processes are aiming at production of high matte grades. Increased oxygen-to-sulfur potential, required by these processes, results in a highly oxidized slag, which in turn leads to an increased concentration of the chemically dissolved copper in the slag phase. Hence, slag cleaning processes are becoming increasingly important for economic viability of the smelting operations. Hydrometallurgical, pyrometallurgical, and mineral processing routes have been used for copper recovery from slag. The current article reviews a trade-off study evaluating two of the commonly used methods (namely flotation and electric slag cleaning furnace) by comparing the technical pros and cons, operability/maintenance requirements, and capital/operating costs of the operations.INTRODUCTIONLarge volumes of smelter and converter slags are produced by copper smelters around the world. It is estimated that for production of each ton of metal 2.2 tons of slag is produced (Gorai, Jana, & Premchand, 2003). Considering the current pressure on the mining and metals industry for “zero-waste, sustainable and environmentally friendly” extraction of metals, it is absolutely essential for metal producers to improve their efficiencies in order to remain competitive. To meet these objectives, almost all metal producers, from steelmaking plants, ferroalloys, base and precious metals producers, are trying to reduce their metal losses to the slag phase. In particular, copper producers are aiming to produce higher matte grades in their smelting furnaces to reduce the converting time and improve their overall throughput. Copper smelters need to minimize their copper/precious metal losses to the slag phase before final landfilling/use of slag. The current article, therefore, briefly reviews the copper loss to the slag phase, methods of metal recovery from the slag and then presents a trade-off study conducted for a green field flash smelter of the sulfide concentrates. A comparison was made between two of the major process routes for metal recovery from slag, namely slag cleaning furnace and flotation."

Jan 1, 2016

By Hassan El-Shall, Ayman El-Midany, Patrick Zhang

Bench and pilot scale testing results suggest that significant improvement in dewatering characteristics of fine particles could be obtained by the addition of fibrous materials. Case studies involving flocculation and dewatering of wastes from phosphate, bauxite, and kaolin processing plants are presented in this paper. Several dewatering techniques were investigated, including sedimentation thickening, filtration, centrifugation, dewatering on screens, and seepage-induced dewatering and consolidation. Advantages and limitations of commercial application of some of the developed techniques arc discussed.

Jan 1, 2004

By O. Mejia

"As study was undertaken to investigate the relationship between mill liner wear and grinding energy efficiency and to assess the opportunity to control mill speed to improve energy performance as mill liner wears. The study involved analysis of plant operating data and liner wear profiles over time. The operating work index was found to be an effective tool to identify the decrease of grinding efficiency along the liner service. The plant data show that the mill grinding efficiency as determined by monitoring the operating work index, and throughput decreases as liner wears. However, efficiency and throughput can be maintained by either changing the liner more frequently or by increasing the mill speed. Two scenarios for increasing mill throughput were analyzed. The first one involves changing the liner before the efficiency drops and the second one requires increasing the mill speed from 75% to 79%. Both scenarios show financial benefits that can be used in mill operations.INTRODUCTION The analysis of the mill power draw is used in this study as a key parameter for comparing mill liner profile and its effect on mill performance. Current technology and simulation software used in the mining industry do not factor in the impact of liner wear profiles in grinding efficiency and mill throughput (Toor, 2013). To address this gap, this study provides an analysis of key factors affecting mill throughput and grinding efficiency: mill speed, ball loading, and liner profiles. Several years of plant mill operating data, published research papers, and MillTraj® simulation results are used to demonstrate that face angles impact grinding efficiency and throughput and that mill speed can be used to overcome this problem. Moreover, the liner profile wear analyses clarify a mismatch between actual and estimated power draw calculations."

Jan 1, 2019

By R. I. Kraydenko, A. N. Dyachenko

"The possibility of SiO2 5N production by staged purification of ammonium hexafluosilicate (NH4)2SiF6 is discussed. High-purity silicon dioxide can be obtained with fluoridation of quartz concentrate by solid NH4F at 100 °C, with further sublimation of the product at 320 °C, its dissolution, ammonia hydrolysis, filtration and drying of SiO2•nH2O. This is accompanied by regeneration of the processing reagent - NH4F.INTRODUCTIONProduction of high-purity silica-5N (SiO2 content over 99.999%) is an important and urgent task of the modern chemical industry. This material is used in the manufacture of optical glass, optical fibers for internet cables, silicon for solar power and electronics.Quartz concentrate is raw material for the production of silicon dioxide. The existing technologies of synthetic silicon dioxide were introduced in the mid-twentieth century. These methods are energy-consuming, multi-step and do not meet stringent environmental requirements. In fact, as some conventional technologies became obsolete; it became necessary to develop new methods for the production of synthetic silica. We believe that the fluoride technology of processing of quartz materials by ammonium fluoride is the most promising direction.In industry, silicon dioxide marked ""Silica White"" is obtained by liquid-phase method. The method consists of the precipitation of amorphous silica from sodium silicate solutions with acids. The resulting product is filtered, washed and dried. Depending on the deposition conditions and nature of the coagulant the ""Silica White"" is acidic, neutral or alkaline. The dry product is subjected to grinding. The degree of dispersion and porosity of the particles of Silica White depends on the nature of decomposition agent (a substance that decomposes the silicate) and coagulant, conditions of sedimentation, filtration and drying. During the drying process the silica particles are sintered into aggregates of a few millimeters."

Jan 1, 2012

By L. Bichler

Lightweight magnesium alloys are gaining in popularity for applications in the automotive and aerospace industries, Their use, however, remains limited due to their relatively low strength and creep properties. Lost Foam Casting (LFC) is a new casting process and the strength of foam cast magnesium alloys has not been investigated in great detail thus far, In this research, magnesium alloy AZ91 E and three new alloys were cast by the LFC process to study the effect of varying aluminum and manganese content on the alloy&apos;s tensile properties, The study reveals, that the tensile strength of the magnesium alloy is closely related to the relative amount of aluminum in the system. Formation of ß-Mg17Al12 phase was seen to significantly affect the yield strength and ductility of the alloy, Furthermore, formation of manganese intermetallic compounds was seen to effectively increase yield strength of the base alloy, Individual alloy morphologies were analyzed via optical and SEM techniques.

Jan 1, 2004

"9.1. IntroductionThe application of the electron microprobe for in-situ analysis of platinum-group minerals (PGM), first reported by Borovskii et at. (1959) and Genkin (1959), has resulted in a large and growing number of analyses of unidentified PGM. Figure 9.1 charts the increase in the number of reported unnamed PGM from 3 in 1959 to a total of 140 by 1979. All these minerals, with the exception of UN1968-5 and UN1976-1, were analyzed with the electron microprobe.There has been no recognised or consistent manner for reporting these unidentified PGM. The term ""unnamed"" has been used for PGM that are considered to be new species without a name as well as for PGM which have not been exhaustively compared to named and unnamed PGM in order to determine whether they are unique. Many of the so-called unnamed PGM are only unnamed because of poor microprobe analyses or because larger than usual elemental substitutions (e.g. Bi for As) made it difficult to calculate the true stoichiometry. Some of these unnamed minerals have been unnecessarily reported with non-stoichiometric formulae, as discussed by Cabri (1980). Better analytical data should reduce the number of such proposals.Another unfortunate practice, possibly used to by-pass the scrutiny of the Commission for New Minerals and Mineral Names, I.M.A., is to report a ""new"" mineral by referring to it by a name made up of its constituent elements. This has been deplored on a number of occasions (cf. discussion in Fleischer et at., 1976, p. 179), but some journals continue to publish such material. The Commission on New Minerals and Mineral Names has not recognised such ""names"" and these PGM are therefore included in this chapter with other unnamed minerals.A further example of inconsistency in reporting unnamed minerals is the report of a specific ideal stoichiometry with no further details (not even an analysis!); sometimes with a note that this will be reported in greater detail in due course. I have also been guilty of similar optimistic statements and, unfortunately, it is not always possible to follow through. Some authors give data on unnamed minerals in such a discrete manner that their reports are sometimes missed in literature searches."

Jan 1, 1979

By G. E. Viens, R. A. Campbell, G. N. Banks

A survey of the literature reveals wide differences in the procedures used in making iron ore pellets and in the properties of the pellets obtained. In this paper, the methods of production and the properties of pellets, as reported in the literature, are examined in an effort to determine what correlations exist between them. An attempt is also made to determine the levels of the properties of pellets which are considered acceptable and desirable in modern practice. M UCH has been written regarding the important changes which have been taking place recently in the iron ore industry. As the demand for ore has increased and the supply of direct-shipping ore has dwindled, tl1e problems associated with the utilization of lower grade ores ha\•e been intensely investigated and important advances in both beneficiation and agglomeration techniques have taken place. In particular, there has been a great deal of activity in connection with the pelletizing method of agglomeration. The superiority of pellets over raw ore has been demonstrated in blast furnace tests

Jan 1, 1962

By E. Wolmarans

The selection of the main mineralised zone (MMZ) concentrator milling circuit has followed a comprehensive route over the preceding 10 years. Many knowledgeable parties have contributed and assisted in developing the milling circuit according to the best available information. The final selection of the flow sheet was completed after DRA conducted a techno-economic study on four possible comminution circuits ranging from conventional crushing and ball milling to fully autogenous (AG) milling. The results from all the above mentioned work indicated that it is possible to treat the MMZ ore at the desired throughputs to the desired grind sizes in a fully autogenous grinding circuit. The flow sheet was designed to treat the main mineralised zone (MMZ) arising?s from both underground and open cast operations and incorporates a fully autogenous grinding (AG) circuit. Commissioning of the 375ktpm concentrator at Nkomati Nickel began in August 2009 with the first ore reporting to the mill on the 15th of September 2009.

Jan 1, 2012

By Joanne G. Petrini

ISO 26000 Unique Process Unique Personality ?Almost 10 years in the making ?What type of standard is this? Different type of ISO Standard ISO 26000 Structure and Substance ?Principles ?Core Subjects ?Implementation Guidance ISO 26000 Impact ?Same old, same old? ?So Is there really anything NEW? ?Should I care??

May 1, 2011

By Gilles Tremblay

The legacy of orphaned/abandoned mines, with their associated environmental liability, human health concerns and the financial costs of clean up is a serious issue facing Canada. In 1999 and 2000, a number of stakeholders put forth requests to Mines Ministers to establish a joint industry-government working group, assisted by other stakeholders to review the issue of abandoned mines. The Ministers supported this initiative and asked that a multi-stakeholder workshop be organized to identify key issues and priorities. The Workshop on Abandoned Mines, held June 2001 in Winnipeg, developed consensus, guiding principles and recommendations that were presented at the Mines Ministers? Conference, September 2001. Ministers agreed on the importance of a large-scale program for the rehabilitation of orphaned/abandoned mines sites. A multi-stakeholder Orphaned/Abandoned (O/A) Mines Advisory Committee was formed and a plan was developed to study various issues relating to the implementation of remediation programs across Canada. Three task groups were formed to address the following key areas: Information Gathering; Community Involvement; and Barriers to Collaboration. The presentation will include a summary of the results of the three projects and the future work plan for the program.

Nov 1, 2002

By Christopher Andreae

"Years before the present iron and steel works were established at Sydney, several thriving although short-lived iron work s operated in Nova Scotia. These furnaces reflected the general nineteenth-century North American experience with iron work s. At the beginning of the century, small furnaces struggled to supply local needs. Charcoal was the principle fuel and water powered most furnace equipment. By the end of the century, a few huge primary iron and steel work s dominated production for Nova Scotia and the rest of Canada.Two sites achieved prominence in the nineteenth-century Nova Scotia iron industry: Londonderry and Ferrona. Londonderry, the larger and longer-lasting of the two sites, is today a small village on the south flank of the Cobequid Mountains, about 30 km west of Truro. Prior to the establishment of an iron works in 1849, no community existed. At the peak of operation in the 1880s, however, over 2,600 people were located there. The second site, Ferrona, today is a mere crossroads on the map, about 10 km south of New Glasgow. Following the construction of a blast furnace there in 1892, a small village grew up around the furnace, but once the furnace was blown out in 1904, the population gradually drifted away.Early HistoryThe history of Nova Scotia&apos;s iron industry began in 1604 when Samuel Champlain became the first European to identify iron ore in the future province. Despite this early acknowledgment, iron was not smelted commercially in Nova Scotia for another two hundred years. Although primitive smelters of the period produced more iron than could be used locally, early settlers depended on imports of iron from Britain and the United States."

Jan 1, 1983

By S. Caron

From the early 70?s, ?Centre de Recherche Minérale? (CRM) has conducted and co-ordinated Research and Development activities for the mineralurgical and metallurgical industries. Since 1999, CRM has continued its mandate through COREM which is a consortium of 13 members that uses the benefits and advantages of collaborative pre-competitive industry / university research. In particular, COREM?s ?In-Situ Optimization Group? is involved in the implementation of modern optimization and control tools. The POP Project was launched in order to increase and consolidate the use of modern optimization and control tools and methods for mineralurgical and metallurgical processes. To ensure a successful transfer in the industry, there are a number of essential activities that have to be undertaken. These activities have been identified by COREM?s members and are grouped into three main modules: - R&D Module: Research and Development in universities, research centres and other partners; - Technology Transfer Module: integration of new tools and methods into the POP Software, industrial applications and technical support; - Training Module: education of new engineers in universities, continuing education of plant personnel through on-site workshops and resource networking by specific information exchange tools. This paper outlines the opportunities that led to the definition of the POP Project and describes its main modules. The main features of the POP Software are presented, the first application is described and finally, future developments are discussed.

May 1, 2001

By A. Lam

The use of a liquid fed direct methanol fuel cell (DMFC) as a power source for micro and small portable applications is attractive due to its system simplicity, low temperature, etc. The aqueous methanol is directly oxidized and does not require additional fuel processing steps as in reformate based PEM fuel cells. In addition, the use of a liquid fuel is advantageous with respect to humidification, stack cooling and system energy density. The DMFC however, has technological issues that must be addressed before it can be widely adopted, particularly in larger applications such as small utility and transportation. At present, the crossover of methanol from the anode to the cathode is a major limitation on DMFC performance and fuel utilization efficiency. In this paper we discuss the influence of fuel modification on the control of crossover. This involves the use of different fuel additives and concentrations to minimize crossover. This appears to be the first reported case of the use of fuel modification (additives) to reduce methanol crossover. The rate of methanol permeation under passive conditions is discussed with respect to the different conditions.

Jan 1, 2005