Search Documents

By J. G. Ross

IN the paper entitled Block Caving at the King Mine (1), which was presented at the Annual General Meeting held in April, 1934, at Quebec, it was pointed out that, owing to certain conditions and financial restrictions, it was advisable to provide a temporary shaft. This was raised from the )00-ft. level to the bottom of the pit, and a 45-degree incline track was constructed up the face of the pit to surface. The temporary shaft and incline were within the ore-body, but were to be used only until such time as the new shaft-the subject of this paper-could be sunk and made ready for operation. After a careful study had been made of all available information pertaining to the ore-body, including examination of diamond-drill core records and geological data, a shaft location was selected well outside the ore-body. Further, since the crusher and dryer buildings are located over part of the ore-body, it was necessary to plan the removal of these buildings and to construct a new crushing and drying plant. This, and the new shaft, must operate in conjunction with the present mill and rock storage bin, which would continue robe used as formerly. No part of this programme, with the exception of drifting toward the shaft site, was started prior to 1937. More than usual detail on technical features is given in this paper in the hope that some parts of it may be of assistance to other members of the Institute who have to undertake somewhat similar work. The engineering and operating staff designed and supervised the work, while at the same time carrying on regular production in four mines at the rate of 12,000 tons of rock mined per day, the output at the King mine being at the rate of 140 tons per hour. No additional engineers were required.

Jan 1, 1939

By John Frostiak

"Kahama Mining Corporation Limited, a wholly owned subsidiary of Barrick Gold Corporation, poured the first dore bar and filtered the first concentrate produced at the Bulyanhulu mine on February 28, 2001. This event marked the completion of the initial development of the Bulyanhulu Mine – Barrick’s first mine located outside of the Americas.Bulyanhulu is a 2,500 tpd underground mine located in the Lake Victoria gold belt of northern Tanzania. Gold is recovered as a gravity concentrate and smelted on site to produce dore bars or collected in copper concentrate that is shipped to offshore smelters. The facilities were constructed to meet Canadian standards. Unit operations include single stage crushing, SAG milling, gravity recovery, flotation, thickening and dewatering. Tailings are converted to paste and returned underground as paste backfill or pumped to the surface tailing site. The surface paste tailing disposal system is believed to be first of its kind in the gold industry. Paste disposal has several advantages over slurry, including lower dam construction costs, reduced water losses, and lower reclamation costs. This paper describes the facilities and discusses the challenges faced during development and construction including logistics, lack of infrastructure, recruiting and training, security, and social issues as well as initial operating results.INTRODUCTIONBarrick Gold Corporation completed the Bulyanhulu mine development in 2001. Capital cost of the project was US$280 million. The mine produced 241,575 ounces from start of milling to year end at a total cash cost of $197 per ounce. Numerous challenges were overcome in the mine’s development due to the general lack of infrastructure in Tanzania and the mine’s location some 1200 km inland by road from the port of Dar es Salaam."

Jan 1, 2003

By Adam Moore, Peter Radziszewski, Matt Gallimore

"Stirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented. In the context of the mining industry, interest in stirred milling technologies has grown over the last 20 years where the typical observation reported inDespite these developments, the tumbling mills are continuing to be used in fine and ultrafine grinding applications. The main reason for this, as communicated at the Canadian Mineral Processors roundtable discussion in 2013, is that the comfort level in understanding stirred milling technologies is not at the level of that of tumbling mills.At CMP 2014, one contribution was made to explore how mill design affects power and energy in a stirred mill. While the 2015 CMP paper explored the application of one scale-up methodology to the Gibraltar case. For the CMP 2016, the aim of this paper is to contribute to increasing the general comfort level with stirred milling technologies by developing a better understanding of the different scale-up methodologies used. This will be accomplished by first completing an overview of the scale-up models found in the literature followed by a review of the different testing and scale-up procedures. This review will be supported by a number of case studies found in the literature. The paper will close with a discussion on some of the challenges that these models and methodologies have and how future research might contribute to overcoming them.IntroductionStirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented (Stehr, 1988). The year 1948 saw the successful application of Du Pont’s “sand mill” for pigment grinding. Subsequent years have led to the development of different types of stirred mills spanning a number of industries that require fine and ultrafine grinding."

Jan 1, 2016

By R. J. Balfour, T. L. Papucciyan

"INTRODUCTIONCapital Cost considerations are basic to feasibility in the achievement of success for Mineral Processing Projects as much as or more than in many other industries. Capital cost is an important factor ae it 1R the unit of measurement for process engineering economic decisions. As a result of ever increasing complexity, alternatives of process and remoteness of site, there is an ever increasing emphasis on accurate estimating and the attendant cost control systems in the international market of today for the Mineral Industry where initial plant costs are becoming a more important factor than operating costs. An undervaluation means trouble ahead. An over-cautious assessment may bring an unnecessary abandonment of a project. Consequently, the ultimate cost must be predicted early and accurately and must be controlled to this parameter during the design and construction phases. Cost Est!~ mating is one of a variety of project management tools used to assist in planning and achieving the optimum balance between Quality, Cost and Time, the eternal triangle of evaluation, namely obtaining a project of acceptable quality at minimum cost and on time. In order to attain these established objectives, proper planning, organizing, coordinating, monitoring, adjusting and controlling the design, procurement and construction elements of the project are essential.This project management approach based upon the principle of a Task Force under single management, comprising a complete service organization, requires a substantial number of qualified individuals specialized in their own field and capable of working together as a team to perform their various functions effectively. The Task Force is supported by their chiefs of discipline and performs in accordance with established procedures and standards under the leadership of a Project Manager.General Engineering Company Limited with the backing of the full resources of Surveyer, Nenniger & Chenevert and its total staff of approximately 1,0009 offers the complete project management service to the Mineral Processing Industry of North America and the rest of the world. As mine sites become more remote and difficult of access, the need for an experienced team of specialists who work under the Task Force principle, with well established standards and procedures becomes even more important. Our long history of successful pro1ecta in this field has been our training ground for the fulfillment of this need."

Jan 1, 1972

By M. Sharafodin, A. A. Hassanipak

Abstract - The essential aims of additional borehole drilling are to improve the reliability of grade and tonnage estimates in each reserve class and to increase ore tonnages. The "GET" function presented in this paper considers strategies for achieving both of these goals simultaneously, and therefore is advantageous for selecting sites for additional boreholes. The "GET" function is either a linear or a non-linear product of three variables G, E, and T: f(G,E,T,) = G??E??T??where the values of any or all of the exponents ?, ?, and ??may differ from unity at the discretion of the user. G and E are the average estimated block grade and the average estimation error for ore blocks in one vertical column, and T is the compounded ore thickness within the column. To illustrate its utility, the GET function has been used for determination of the most advantageous sites for additional drilling in the Shah-Kuh Pb-Zn deposit in west central Iran.

Jan 1, 2004

By J. E. Nesset

"I had been requested earlier this year by MetSoc, our sister society of CIM, to contribute a chapter on technical developments in Canadian mineral processing over the past 50 years to their 50th Anniversary volume. Accepting the challenge of assembling such a chapter seemed at first a reasonably straightforward task, until one realises that the list of contributions by Canadians to mineral processing over this period has been more than just significant. It turns out to have been an extraordinarily fertile time for innovation and impact for Canadian-based technology. The list is necessarily a subjective one, however I had no trouble identifying twenty technology developments that are clearly outstanding, and there are undoubtedly others. As much as possible, I approached the individuals themselves who played key roles in each technology and asked that they tell the “story”. Without exception, all who were invited accepted eagerly and delivered more than I had hoped for. The technologies have been grouped into those that are truly Canadian innovations, such as the Knelson gravity concentrator and the McGill gas dispersion sensors in flotation, and technologies where Canadians and Canada played a very significant role in their success and implementation, such as AG/SAG grinding and ion-beam surface analysis. Also included are what may be termed technology transfer initiatives and institutions that have risen to a world class level, such as SGS Lakefield and the Canadian Mineral Processors Society of CIM. The challenge is now for the coming generation to continue this record of innovation and contribution to the industry, and that includes the (mostly) Canadian mining and metallurgical companies who have taken the longer term view and supported many of these initiatives, through their critical early years, with both financing and project sites for these ideas. Let us hope that the current trend of mining company globalization will not dampen their enthusiasm to participate. This plenary presentation will highlight many of these technologies, the individuals behind them, and their significance to the mineral processing industry."

Jan 1, 2012

By J. B. Gilliatt

The discovery of ore at Wabana was quickly followed by the mining of the ore beds where they outcropped in the land areas. The third phase, as at present carried out, consists of extensive submarine operations, which were commenced in 1908, by driving a pair of slopes out under Conception bay, opening. the mine for a distance of a mile and a half from the shore. Two other slopes, now driven just beyond the shore line, are being sunk to the submarine territory where, it is generally recognized, huge reserves of ore lie under the bay. The process of erosion of the land, the solution and re-disposition of its iron-bearing minerals in thick beds of ore have been considered elsewhere, but these bear small relation to the physical forces which have acted upon the ore-beds since the deposition of the strata. These physical changes are made manifest by jointing and cleavage and faulting. The discussion of these, the relation they bear to each other, and to the folding of the strata, is the purpose of this article. For the benefit of those who may not be familiar with the formation in which the ore occurs, I include a general summary of the geology of Be!! island and its environs; also a description of conditions that prevailed during the period of deposition, so that the reader may appreciate some of the later changes that took place during or subsequent to its emergence from the sea, and the folding or tilting of the strata to the position it now occupies.

Jan 1, 1924

By Pavel Vasak

The Laurentian University Virtual Reality Laboratory (VRL) has provided a unique platform for the development and testing of novel seismic and microseismic data processing and visualization technology. In collaboration with Vale?s Creighton Mine, the technology was implemented at the mine site and consists of a VRL system and site calibrated Seismic Excavation Hazard Map (SEHM) software. The SEHM was developed as a practical solution for the mine operator to identify areas of elevated, active rock mass damage processes caused by recent mining activity. This paper is a pictorial representation of the 3D stereoscopic demonstration of the Creighton Mine seismic data distribution and interpreted SEHM for the first quarter of 2009. A live demonstration is scheduled at the Laurentian University VRL as one of the conference field trips. The demonstration highlights the technology transfer of research concepts into a near-real-time excavation hazard system that utilizes the key aspects of virtual reality technology; the ability to integrate large datasets (geology, mine excavation, (seismic) monitoring data, production scheduling, stress model, etc.); the ability to manipulate and visualize large datasets in both space and in time (mining sequence); and the ability to review the datasets by a group of experts in an immersive (3D stereoscopic), collaborative environment to better understand the processes and context of the mining-induced seismicity and evaluate potential risks to the mining operation.

Oct 1, 2010

By Paul Staples, Chris Morley

"The development of the Cerro Verde, Amplats Mogalakwena and Boddington projects over the last few years has helped to establish the use of high pressure grinding rolls (HPGR) in comminution circuit designs in large-scale hard-rock applications. The increasing acceptance of this innovative and sometimes controversial technology has had the natural effect of prompting many other new projects to examine HPGR as an alternative to the established, usually SAG-based, comminution circuit design approach.At the current stage of development of the technology, HPGR-based circuit capital costs are generally higher than for the equivalent SAG-based circuit, so that HPGR must offer sufficient operating cost benefits to offset the additional capital costs over an acceptable pay-back period. It is usually necessary to undertake comprehensive project-specific trade-off studies to quantify this effect.This paper describes the processes involved in the execution of a typical SAG-HPGR trade-off study, from the preliminary assessment of ore characteristics and project criteria, through testwork, circuit modelling, equipment selection and cost estimates, to a project-economics comparative assessment of the options. The trade-off study determines both the technical feasibility of the respective technologies and their commercial viability in the given project setting.The paper concludes with a cautionary note to the effect that, while HPGR has many potential benefits, it is not a panacea, and that, for some ore types and project conditions, the more established conventional technologies are often more appropriate."

Jan 1, 2010

By Francis W. Gray

Introduction Extensive undersea coal-mining has developed on both the east and west coasts of Canada, and at this time some four million tons, or 25 per cent of the total output of Canadian coal, representing a pit-mouth value of $14,000,000 per annum, is coming from coal seams lying under the sea. Of the coal now being mined in Nova Scotia, 55 per cent comes from under the sea, and this proportion is likely to increase. The Province of Nova Scotia is at this date receiving in royalties paid upon coal ?removed from undersea areas a sum exceeding $400,000 per annum. The subject is, therefore, one of special interest to the Mining Society of Nova Scotia and the Canadian Institute of Mining & Metallurgy, and while this paper will deal chiefly with undersea coal-mining in Nova Scotia, an attempt has been made to summarize the development of mining practice in the winning of undersea coal in other parts of the world, with the hope that such a recital may assist in the assessment of local problems. The connection between the mining of coal under the sea and an insular or maritime geography is obvious in regard to Great Britain, Japan, Vancouver Island, Australia, and Cape Breton Island, and also in regard to the curious conformation of Chile; the tendency towards growth of a mercantile marine and naval eminence is equally obvious where coal is mined at tidewater. But, there is the further and less favourable significance that the mining of coal under the sea is associated with poverty rather than with abundance of coal reserves.

Jan 1, 1927

By David Stephenson, Hugo Granados, Steven Klohn

"HudBay’s Constancia project is a copper molybdenum concentrator located in southern Peru. In 2010 Ausenco was contracted to perform a feasibility study optimization review which resulted in an improved design with significantly increased throughput capacity at a minimal increase in capital cost. Construction began in 2012 with commercial operation commencing in May 2015. This paper outlines the process plant design as well as describing the plant’s major equipment selections, start-up and early operations experiences.IntroductionHudBay Mineral’s Constancia project is located at 4200 meters above sea level (masl) in southern Peru, approximately 630 km south-east of Lima, Peru. The property can be accessed by road from Cusco, Peru, (approximately 110 km to the north), or from Arequipa, Peru (approximately 215 km to the south). Matarani, accessed via Arequipa, is the closest port.Constancia is located within the Yauri-Andahuaylas metallogenic belt. The region contains several large copper-gold-molybdenum porphyry deposits such as Antapaccay (by Glencore) and Los Chancas (by Grupo Mexico), and copper skarn deposits such as Tintaya (by Glencore) and Las Bambas (by MMG). Constancia’s ore reserves contain copper and molybdenum with trace amounts of gold and silver.Ore is mined by an open-pit operation. The process plant recovers copper and molybdenum concentrates, storing tailings in a conventional tailings management facility. Infrastructure at the site includes a grid power supply (via a 70 km overhead transmission line from Tintaya), water supply, workshops and an accommodation camp. Mine life is 22 years.Site construction works began in 2012 with first copper concentrate produced in late 2014. The project was executed for approximately 1.75B$USD.Ausenco’s design approach focussed on developing a capital efficient copper molybdenum concentrator. This paper outlines key features incorporated in the concentrator design, plant layout and equipment selection, as well as start-up experiences and early operational results."

Jan 1, 2016

By H. Cay, J. Zachwieja, T. Esplin, R. Ravenelle, T. Olsen-Tank

Barrick Goldstrike mine utilizes a carbon-in-leach (CIL) circuit to simultaneously leach gold into solution with cyanide and adsorb the gold-cyanide complex onto activated carbon for further refinement. If the gold bearing ore contains a significant amount of native carbonaceous material, gold cyanide can be adsorbed at these sites instead of onto the desired activated carbon and the gold is effectively lost to tailings in a detrimental process known as "preg-robbing." The preg-rob effect is considerably reduced by treating the ore with a surfactant, which is hypothesized to adsorb to and passivate the native carbon surfaces. Past laboratory and pilot studies have consistently demonstrated significant gains in gold recovery after treating carbonaceous ore with surfactant. With success in bench and pilot scale testing, a plant trial was conducted at Barrick Goldstrike to evaluate the feasibility of using an alkoxylated fatty amine surfactant (Ethomeen T/12) to aid in the leaching of high preg-robbing ores. This paper analyzes the performance of the surfactant during the plant trial in addition to the problems that occurred during the trial period. Suggestions for improvement are also discussed.

Jan 1, 2014

By Brian Hart, Stamen Dimov

"The Time of Flight Secondary Ion Mass Spectrometer (ToF-SIMS) is unique in that it measures the outermost atomic layers of any material. The technique is particularly suited for determining surface chemical composition of mineral particles. It is most commonly used as a diagnostic tool to measure mineral surface chemical variability in plant and bench top flotation separation processes. Recently, research towards understanding the full capability of the instrument has resulted in the development of new diagnostic applications related to various Au extraction technologies and the development of the ToF-SIMS as a predictive tool for assessing the chemical reactivity of the ore.In this paper we will present a brief review of the ToF-SIMS technique with recent advances in instrumentation and methodologies including:•,?recent developments and advances towards a semi-quantitative approach to the evaluation of mineral surface modifiers (ex. Cu),•,?flotation case studies investigating activator, depressant and collector loading variability within a flotation process,•,?the recently developed chemical reactivity test which we believe has the potential to predict the behaviour of minerals in a flotation test in response to chemical transfer during grinding,•,recent applications for determination of surface Au preg-robbed in carbonaceous materials.A portion of this material has been recently presented at the COM 2009 meeting and at SIMS XVII (see Dimov et al 2009 and Hart et al, 2009).INTRODUCTIONIn flotation seperation surface chemistry is the principal determinant for selective separation of the various mineral phases (Ralston, 1994, Smart et al, 2003). Determination of this hydrophobic/hydrophilic balance by particle therefore requires correct identification and selection of the particular mineral phase(s) followed by a statistical analysis of the surface chemical characteristics of the particles with an estimation of the spread of values (Smart et al, 2003)."

Jan 1, 2010

By L. R. Plitt, A. A. Turak, B. C. Flintoff

"Since the publication of empirical cyclone models by Lynch and Rao in 1975 and by Plitt in 1976, the technical literature on this subject has consisted primarily of reports of applications, with only a few articles discussing basic modifications or enhancements in model form. In fact, most of the modelling eff ort in this period has been concerned with theoretical models based on the hydrodynamics of multiphase flow. (Preliminary resutls have been encouraging, however, it will be some time before this approach reaches the practical application stage.) This paper presents a review of empirical cyclone modelling technology, with an emphasis on developments since the mid 1970s. The topics addressed include homogeneous and heterogeneous ores, parameter estimation techniques, parameter confidence intervals, and the introduction of a new conceptual model of cyclone operation.IntroductionSince their first reported application in the mineral industry by Driessen (1939), cyclones have become a common unit operation in all of the process industries. The widespread use of the cyclone stems from its relative low cost and its versatility. It can be employed to carry out liquid-liquid, solid-liquid and solid-solid separations. It is the area of solid-solid separation which is of greatest interest to a mineral processing engineer. Historically, this area was divided into two application categories: (I) Separation according to density, the cyclone washer, and, (2) Classification according to particle size, the cyclone ciassifier. (When water is the carrier fluid, the cyclone is more often called the hydrocyclone. For the purposes of this paper the two names are used interchangeably). Classification is the principal application in mineral processing circuit s. Within this category, the cyclone is most commonly employed to provide some positive control over the size distribution of product from a grinding circuit. Other uses include sand-slime separation prior to froth flotation and mill tailings treatment, either for dam construction or in backfill preparation."

Jan 1, 1987

By Robert Keyes, Charle Knowles, Glenn Kendall, Gary Fletcher

"The metal mining industry in Canada has been dramatically affected by the changes that have occurred in the world mineral market place. World economic restructuring in the post ""oil shock"" period of the mid-1970s, greatly increased competition from suppliers in the developing countries, and commodity price and currency pressures have all combined to severely test Canadian competitiveness. In the new mining world, the rate of growth of demand for metals has declined due to product downsizing, materials substitution, and a relatively slower growth of over-all world economic activity.The interplay of market and political factors is complex. Canadian metal mining companies must compete in world markets against low-cost producers in developing nations whose priorities often appear to be centred on maximizing foreign exchange earnings to foster development goals and debt repayment. Many of these countries have high levels of government intervention in their mining industries. The result is a greatly in-creased number of suppliers all vying for a share of a world demand growing at a relatively slower rate than in the past. To be able to compete under these circumstances, Canadian companies have had to undertake 'survival mode' measures and look to new ways of doing things. In order to identify the effects that the recent market and economic trends have had on the Canadian metal mining industry, a study was undertaken by Canada Employment and Immigration to assess these changes and their implications for the metal mining workforce.The Canadian Occupational Projection System (COPS)—Sector Study Group with the cooperation of the Mining Association of Canada, undertook a human resource survey to gather current employment and occupation information. This formed an important part of the Canadian Occupational Projection System Metal Mining Sector Study. This article addresses the with survey results, a C.E.I.C. worker mobility study, and trends and issues that are changing the mix of jobs and the way they are being done.Figure 1 shows metal mining employment for the period from 1974 to 1984. It provides a clear picture of the employment swings that the industry has experienced especially during the recession period of 1981 to 1983. From 1981 to 1983, employment dropped by 14 000, from 68 000 to 54 764, and then dropped to its lowest point in 1984 of 52 783. We feel that employment in the medium term will be flat with growth in gold mines being largely offset by continued workforce rationalizing in other sectors.Perhaps the key point is that equivalent levels of output have been achieved in the recent period (1981-1984) with a workforce that is 25% smaller than it was in 1974. This also raises the questions which the COPS/MAC survey and COPS mobility study sought to clarify, namely, what jobs have been cut and where have these people gone? Equally important are the questions of occupational skill level changes, and what types of jobs are declining and which ones are becoming increasingly important, as economic and technological changes have altered the mining work place."

Jan 1, 1987

By M. Ramström

"In 2002, Atlas Copco Rock Drills AB released the new rig control system (RCS) technology for all of its drill rig types. RCS opened the way for a new generation of computerized drill rigs based on modern, standard PC-computer technology. Drilling accuracy, information logging, reduction in manpower in some types, and serviceability have all taken a quantum leap forward when compared with previous generations of drill rigs. RCS is modularized and distributed by means of CAN-bus technology. This technology, which is well proven in automobile applications, forms the communication backbone of the rig. The modularity facilitates almost unlimited possibilities for the expansion and adaptation of drill rig functions."

Jan 1, 2005

By P. P. Sinha, D. N. Bhatia, B. R. Ghosh, R. K. Gupta

Medium carbon, low alloy, high-strength steels containing Ni, Cr, and Mo are used for the fabrication of various types of high-strength fasteners required for launch vehicle structures. Cold heading properties and response to hardening and tempering are the essential requirements of the material for fabrication and application, respectively. Combining these two requirements is essentially warranted in high-strength fastener-grade steels. Cold heading properties require ductility, which can be achieved through spheroidizing treatments. In the absence of a suitable spheroidizing cycle for medium carbon 3.8 Ni, 1.8 Cr, 0.3 Mo steel, experiments were carried out with a theoretical understanding of the alloy system. This paper presents the experiments and results obtained after a spheroidizing treatment, which was carried out to optimize the process. Hardness measurements were carried out and microstructural studies were conducted to assess the spheroidization process and to determine the optimal spheroidization parameters.

Jan 1, 2007

By Ross Nairn

"Tulawaka Mine is a joint venture between Pangea Minerals Limited 70% (a wholly-owned subsidiary of Barrick Gold Corporation) and Northern Mining 30%. Tulawaka Mine is located in North West of Tanzania in the Lake Victoria Goldfields. Tulawaka Mine is scheduled to process 360,000 tonnes per year at an average 11.5 g/t head grade over a 4 year mine life.The Tulawaka Process Plant uses single stage crushing, single stage SAG milling, gravity, intensive leach of gravity concentrates, CIL, Zadra desorption and cyanide detoxification to process the ore. Gold recovery exceeds (or is expected to) 95%.The Process Plant was designed and constructed under the supervision of Ausenco Engineering of Australia. Site works commenced in January 2004, Process Plant construction commenced in July 2004 and the first ore was presented to the Process Plant 26th February 2005. The first gold was poured on 15th March 2005. All construction contractors were demobilized from site 7th April 2005. Major achievements have been 3.4 million hrs LTI free during construction and operation to date, training of the Tanzanian workforce at Bulyanhulu Mine prior to commissioning, a succession plan to replace expatriate personnel with Tanzanian staff and significant over performance of the Process Plant against design.INTRODUCTIONTulawaka Mine is situated approximately 160 km south west of Mwanza in the western Lake Victoria Goldfields District of north western Tanzania. The property is held under a joint venture between Pangea Goldfields Inc (70%), a wholly owned subsidiary of Barrick Gold Corporation, and Explorations Minieres Du Nord Ltée (30%). A location map showing the position of the operation in Tanzania is shown in Figure 1.Mine site staff at Tulawaka comprises a combination of Tanzanian and Expatriate personnel. All Pangea personnel live on site and commute to their place of residence for their R&R on a 9 weeks on 4 weeks off roster."

Jan 1, 2006

By D. Rylander

The operation of Quarry and Aggregate sites are similar to factory production, since it contains sequential production processes, tasks and activities to produce the output product. Compared to the plant though, the quarry processes are generally not synchronized and controlled towards the overall throughput of the site in real time. Some quarries control parts of the production but do generally not utilize real-time technologies for the whole site and all its activities. This fact indicates a general improvement potential in increased productivity at quarry sites, but also unsolved challenges for the same reason. The main contribution of this paper is the presentation of a Lean based method for how to describe the processes to identify control improvement potential within a site. The aim of the identified improvements is to increase overall site productivity by optimizing site, fleet and machine utilization towards the overall throughput, and minimizing operational expenses and inventories. Further the paper exemplifies the method?s usability with field studies at operational quarry plants successfully identifying and quantifying potential wastes and improvements. In addition the identified productivity improvements based on increased control and automation indicate challenges and needs in wireless communication and sensing technologies.

Aug 1, 2013

By Ross Byron, Ken Roberts

"During the fall of 2001 a program was initiated to determine the feasibility of improving the metallurgy in the flotation circuit at the Penhorwood Talc Concentrator located near Timmins, Ontario. Bench scale testwork led Plant staff to believe that opportunities existed to improve the flotation performance. Pilot scale testing was then conducted using two vendors and their respective cylindrical type flotation cells to indicate where these opportunities existed.The results of the test program determined that the replacement of the existing flotation circuit (roughers, scavengers and cleaners) with new flotation cells could be economically viable. Justification was due to a reduction in installed horsepower, maintenance costs and a subsequent increase in recovery and throughput while maintaining product quality. Unforeseen benefits included reagent and air reduction, accurate level control as well as improved working conditions due to the removal of the antiquated equipment and ancillaries.This paper will detail the justification, installation and implementation of the new flotation circuit. A special emphasis will explain the hurdles encountered while trying to install and commission the circuit in an operating Concentrator with minimal interruptions to production.INTRODUCTIONThe Penhorwood mine and Concentrator is 28 yrs old and has gone through many ups and downs with different owners, Johns Manville, Steetley Talc and now Luzenac. It has also been expanded twice, with flotation and grinding capacity being added in recent years.All of the concentration is completed at the mine site while the fine grinding takes place in the Timmins micronizing plant.Luzenac’s Philosophy is to be the world leader in Talc production, technology and sales, having about 70% of the current world High Grade talc market."

Jan 1, 2004