Search Documents

My early experience with the coal industry was in the latter half of the 1970s, where attention to only ones own æaccidentsÆ and concentration on behaviour controls were impeding the introduction of effective engineering controls such as ROPS, FOPS, roof support and residual current devices. Lack of the broad picture of personal damage and of relevant veridical (true saying) knowledge and data had to be overcome to achieve progress in reducing fatalities. Thirty years on, it is again necessary to take stock. How good is our knowledge, our data, our information on which we make decisions. Despite Australian all industry 1992-93 data showing 80.5 per cent of costs came from occurrences which permanently altered peopleÆs lives, New South Wales is still the only state reporting permanent disabilities. In 1991 - 1992, the rate of permanent disability per 1000 wage and salary earners was two. In 2000 - 2001, it was over four û more than doubled. Also strongly motivating is the huge cost. Industry carried 25 per cent of the $34.3 billion costs for 2000 - 2001, up ten per cent of 82.8 billion if the costs of pain, suffering and early death are included.

Jan 1, 2005

The Green Parrot and Reward stratabound silver-lead (copper-zinc) deposits are located in the eastern part of the Arunta Block. At Green Parrot, mineralisation is contained within a north-south striking lode horizon comprised of elongate lenses of massive garnet or calcsilicate-carbonate "lode rocks" with intercalated sericite-biotite schist and laminated biotite-feldspar schist. The "lode rocks" are increasingly calcareous to the west. The mineralisation is broadly zoned with an increase in lead content and decreases in copper and silver contents from east to west. The principal sulphide minerals are galena, sphalerite and bornite. The Reward deposit lies adjacent to a lens of massive garnet "lode rock" which is contained within garnetiferous sericite-quartz schist. Primary mineralisation consists of galena, chalcopyrite, sphalerite and pyrite. Both deposits are associated with a substantial thickening of the lode horizon which is narrow and discontinuous along strike from the Green Parrot and Reward deposits.

Jan 1, 1984

By Kupper T

Firstly, electric analog models are discus- sed to show fluid streaming conditions. In these models the depth of blast at tuyere level, the height of the bath, the influ- ence of different angles of the furnace zones and the different possibilities of the root of the cohesive zone have been changed. Tests to define the influence at a large blast furnace are given. Secondly, the wear of carbon bricks in the hearth is examined under the influence of gas, slag and pig iron. Oxidation tests in a special scanning microscope with the pos- sibility of heating and gas treatment are shown. Wear mechanisms are discussed fora large blast furnace and proposals for im- provement are given. Finally, the possib- ilities and value of the temperature meas- urement in the hearth block are discussed.

Jan 1, 1981

Methods of measuring the frictional properties of rock surfaces, both by direct sliding and in triaxial apparatus, are described. It was found that for some rocks the coefficient of friction remains reasonably constant as sliding is continued but for others it increases considerably.The effect of fluid pressure in the surface of sliding was found in all cases to be adequately represented by the effective stress criterion. Some observations on sliding on two conjugate planes showed that the motion on the two planes may be very different, depending on small differences in the constraints.The coefficients of friction of natural open joints in bore core were found to lie in the comparatively narrow range 0.32 to O.68 although surface coatings were very diverse.A set of diagrams on the equal area projection is given which enables a rapid determination to be made of those planes on which sliding is possible in a given three-dimensional stress field. The influence of the intermediate principal stress on this is of considerable importance.

Jan 1, 1969

By G A. Davis, D G. Laughton

The great variability of mineral and energy prices has motivated some governments to incorporate a windfall profits tax into their mineral taxation regimes. Windfall profits taxes are a means for governments to capture additional mineral revenue when mineral prices are considered higher than some historic level. Governments need to be aware of the effects of such contingent taxes on the exploration, development and operating decisions of mining companies. Mining companies need to be able to calculate the full impact of windfall profits taxes on the economics of their projects. This paper examines the valuation of a multi-phase copper-gold project in the presence of a windfall profits tax. Real options Monte Carlo simulation is used to characterise the different exposures of the mine owner and of the government to the risky cash flow streams that they receive from the project. The results highlight that Monte Carlo simulation paired with the real option valuation method is able to account appropriately for the differing risk exposures, while the traditional discounted cash flow valuation model is not. Our key conclusion for governments and mining companies is that the impact of contingent tax and royalty terms can and should be assessed using advanced valuation techniques, and the results used to improve contract designs under the constraint of actual and perceived fiscal system stability.

Jan 1, 2007

By Abdalla MH

The deformation resulting from the presence of a tunnel may signifcantly affected, nearby structures and need to be considered during design of both tunnel and structure. The aim of this paper is to study the effect of different factors which may affect the interaction between the tunnel and the str- ucture. These include; the depth of both tunnel and foundation level of the structure ( z and t ), distance between C.L. of tunnel and loads, breadth of the loaded area, Diameter of tunnel and lining of the tunnel. The problem is studied as a two dimensional plane strain model by the boundary element technique. The results of this study indicated that the presence of a cavity/tunnel increases, in general, the vertical displacement on the ground surface and at the foundation level as well as the horizontal and vertical stresses in the cavity/tunnel level. The effect of eccentricity is increasing as e/D decreasing. For pile foundation there is a quite different- influence of the presence of cavity/tunnel in both cases of friction pile and end bearing pile type of foundation.

Jan 1, 1987

Violarite, (Ni,Fe) 3+x S4, is a ubiquitous secondary mineral in the supergene alteration zones of massive nickel sulphide deposits in Western Australia. It is formed by the pseudo- morphous replacement of pentlandite, pyrrhotite and/or millerite, and retains the textures typical of these precursors. Although the composition of the first-formed violarite is related to that of its precursor, supergene enrichment results in an increasing nickel:iron ratio toward the top of the supergene profile. In pentlandite-pyrrhotite ore, the replacement of pentlandite by violarite releases some nickel, which is consumed by the partial conversion of the pyrrhotite to iron-rich violarite. In pentlandite-millerite ore, on the other hand, the pentlandite, on conversion to violarite, appears to release excess iron that participates in the partial conversion of millerite to nickel- rich violarite. The characteristic textures exhibited by the secondary violarite and its replacement products in supergene and gossanitic deposits overlying massive nickel sulphide ores generally enable the original mineralogical compositions of the primary ores to be inferred.

Jan 1, 1973

By M Ujihira, M Komazaki, K Higuchi, D F

A diesel engine with a misfiring cylinder is likely to break down in a short time when the engine is used without maintenance. The authors have developed a method of detecting the occurrence of cylinder misfiring and specifying the misfiring cylinder by using wavelet analysis and statistical analysis on the root mean square (r.m.s.) values of two kinds of acceleration waveforms. This detection method is considered superior to traditional methods, which require several accelerometers, especially in terms of simplicity. Since the development of the method, research has been conducted on semi-automatic processing of measured signals and signal transmission from the worksite to a remote office. Field tests confirmed that 1 + 105 points of dynamic data could be transmitted through the mobile multimedia network within 15 minutes, and the time for signal processing was within 15 minutes. Final determination on the condition of a diesel engine in heavy machinery could be achieved within 30 minutes. Shortened processing time is expected by improvement of the processing software.

Jan 1, 2003

By G P. J Dijkema, M A. Reuter

From a material cycles perspective all processes are interconnected and consequently a process can never be evaluated as an isolated and independent unit. This also holds true for the evaluated co-incineration options. Environmental and sustainability issues for example, such as raw material and energy utilisation or air pollution, are a resultant of the whole system of industrial activities. It is therefore important, not to optimise a single process or industrial activity, but rather the whole system. Although engineering procedures for the design of individual industrial units are well developed, the problem of determining the best arrangement of these interconnected units is often far more difficult. Regulation that manages the arrangement of the units for waste processing is still under construction. In the evaluation of co-incineration, analogous principle from process control can be used: feedforward control. This principle includes the determination of which outlets can be used for all process outputs, hence avoidance of any æunusableÆ products or wastes possibly arising from co-incineration. To establish the extent, to which produced wastes are usable, a system overview is necessary, in addition to in-depth information on the subsystems, which produce and can consume wastes. Material cycles modelling can be used as the basis for a tool that supports the development of a suitable playing field. It should provide overview of the system and in-depth information on its subsystems. This tool then represents an attempt to bridge the gap between æholisticÆ industrial ecology and process engineering.

Jan 1, 2000

By P K. M Mazzoni, D Frantois-Bong

This paper aims to show alternatives to the estimation methods used for finding the parameters in GyÆs well known model for sampling variance in the case of particulate materials. Many experiments designed for gathering data on the sampling variance for specific mineral deposits allow the experimenter to use approximations in the calculation of the parameters of the mathematical model involved, which sometimes can be very useful. However, there are some instances where approximations lead to biased estimates of the parameters, and consequently, lead to errors in the establishment of the sampling protocol and treatment of quality control data. In the present work, an alternative is presented for computing the parameter values based in any experimental set up, without the need for any simplification. The method was derived using the method of least squares and evaluations are made using the usual tools in this kind of methodology: residual analysis and evaluation of the fit by means of a plot of calculated versus experimental variances. With the aid of these tools, one can better evaluate the structure of the experimental errors in such applications, and the adherence to the proposed model. In addition, it is possible to perform hypothesis testing for the equality of different sampling procedures in terms of sampling variance. The full mathematical details are given, together with an algorithm for applying the method, which can be implemented easily using any computer language. An illustration of the method is shown, considering the international work done in ISO/TC 102. This example is a determination of the minimum sample mass to be collected in iron ore shipments, in order to achieve a specified sampling precision.

Jan 1, 2005

This paper is intended to continue the subject in the light of recent work, from where it was left at the conclusion of the discussion on the excellent paper by the late Mr. Noel Haszard. The position then obtaining is briefly summarised below:-The points which received general agreement at that time were:-'(1) That the gold occurs, probably in an elemental form, in a state of very fine division in the pyrite.(2) That the aim in roasting of Kalgoorlie flotation concentrates should be to obtain the maximum porosity possible. The gold tellurides were amenable to treatment with either a' solution of high lime and cyanide strength combined with fine grinding, or bybromocyanidation without re-grinding.(3) That a low roasting temperature is essential during the elimination of the first atom of sulphur, if the final calcine is to give a good extraction by cyanidation.(4) Even with the best temperature conditions of roasting then determined, and after a period of cyanidation of the calcines until no further extraction was obtainable, the lowest calcine residues obtainable were equivalent to approximately 1·8 dwts. per long ton, based on an original concentrate of pure pyrite.There was some division of opinion at the time as to whether the temperature of the later stages of roasting was significant, and also as to the reason why the initial roasting temperatures had so marked an effect.

Jan 1, 1939

By Canning RG, Uusna S, Goodheart BA

The paper outlines the development of"a process for removal of iron oxides from ilmenite, thereby upgrading the TiO2 content of Western Australian ilmenites, from 55 to approximately 90 per cent. In the first stage, the iron oxides are reduced with solid carbon (coal) to metallic iron. Experimental reduc- tions were carried out in crucibles,, a fluidised bed and a small pilot plant rotary kiln. The reduced'ilmenite is,then agitated in aerated water, in the presence of catalysts, so that the iron "rusts" away from the ilmenite'grains and the precipitated iron oxide is easily separable by decantation. The influence of variables on the rates. of reduction and oxidation are discussed, The oxidation rate was exam- ined for both - the' physical oxygen-transfer characteristics and electrochemically by reference to Peurbaix diagrams, which plot redox potential against solution 'PH, The upgraded ilmenite is expected to be an attractive material. for pigment -manufacture,, and the iron oxide has prospects of being a marketable by-product. The process may possibly be. applied, to .other..ores.

Jan 1, 1964

By K Nakashima, K Aya, T Sumita, N Saito

Electro slag remelting (ESR) is one of the methods used to produce high-cleanliness steel. In the ESR method, the product steel electrode is immersed in flux, and the electrode is melted by the Joule heat of the flux generated by high current. CaF2-based melts are mainly used as fluxes, but the electrical conductivity of CaF2-based melts varies widely among researchers and measurement methods. Therefore, this experiment aims to measure the electrical conductivity of CaF2-based melts based on the van der Pauw-Ohta method, which does not require the cell constant that is a fundamental error factor in electrical conductivity measurement at high temperatures. The measurement temperature was set at 1450–1600°C, and dehydrated Ar flowed through the furnace at 200 mL/min. Electrodes were fabricated by Pt-30mass per cent Rh alloy, and the electrodes were connected to an impedance analyser using a four-terminal probe. The electrodes were immersed in the melt, and the impedance and phase angle were measured by AC frequency sweep (50 Hz to 200 kHz). The electrical conductivity was then calculated by utilising the impedance’s real part values when the impedance’s imaginary component was zero. The electrical conductivity showed a positive temperature dependence. The electrical conductivity of 60(CaO⋅Al2O3)-40CaF2 melt increased with increasing temperature but was found to be roughly one-third of those of the previous studies. In the conductivity measurement of 60(CaO⋅Al2O3)-40CaF2 melt, the AC frequency with a phase angle of 0° was found to be different depending on the temperature and immersion depth. By sweeping the frequency, the impedance at the phase angle of 0° can be obtained, which enables us to measure the electrical conductivity more accurately.

Jun 19, 2024

The desire for minimising impacts of mining activities on the environment, and in particular, water resources; is usually tempered by the costs and practicalities of implementing æbest practiceÆ measures. This paper briefly discusses the theoretical and practical options for water management for typical mines and quarries in a range of environments to assess if adverse impacts can be completely eliminated or at least be perceived as doing so. The regulatory requirements for water resources management are usually an essential part of mine planning and operations that can be a primary focus for all stakeholders. As such they can distract attention from implementing best practice in water management for the benefit of the environment and the community for altruistic reasons that have a long-term benefit for the mining industry as a whole. Cost-effective options for supply, demand and quality management of water that comply with basic regulatory requirements are readily available. Making a mine æinvisibleÆ in a practical sense, in terms of impacts on water resources would require eliminating potentially contaminated discharges, minimising demand, maximising reuse and recycling and putting back a healthy proportion of the clean water that is taken out of the natural environment for use in mine operations. This may sound simple enough and there are many well-known standard approaches that are usually applied. But which are the most effective, and who benefits? New approaches to water management are becoming more affordable and can benefit the bottom line as well as the environment, but can they make a mine ædisappearÆ? The perception of whether a mine is æinvisibleÆ in terms of its impacts on water resources is as important as the actions taken to try to achieve such an objective. The viewpoints and thresholds of perceptions of the different stakeholders are therefore relevant to how ævisibleÆ mining activities become.

Jan 1, 2006

By T Cutts

Since 1989 Kalgoorlie Consolidated Gold Mines has managed the Kalgoorlie gold operations of joint venture partners Normandy Mining Ltd and Homestake Gold of Australia Ltd. Current production from the Fimiston Open Pit is approximately 650 000 ounces per annum. The mine incorporates a multitude of narrow shear hosted, subvertical lodes, predominantly within Golden Mile Dolerite. Traditionally KCGM has used blasthole based grade control in the Fimiston pits. A single sample is taken from vertical production blastholes, drilled on ten metre benches. This process was improved with the addition of infill drilling along blasthole rows to provide additional samples across strike. However the limitations of adequately defining subvertical mineralised structures with vertical blastholes remain. In 1997 the first of two trial areas were drilled with close spaced, inclined Reverse Circulation (RC) drilling. These tests indicated that RC based grade control had the potential to provide significant advantages. These include:improved delineation of mineralised structures, particularly across strike; reliable short-term mine schedules based on the advance data available from drilling over three benches; and the angled RC drilling is capable of providing samples of near stope and stope fill material which often remains unsampled by blasthole drills due to the safety constraints around unstable underground openings. Based on the success of this initial work RC based grade control was gradually implemented across production areas commencing September 1998. Some of the many challenges faced include:development of effective procedures and systems for the planning, logging, interpretation and modelling of the RC data; obtaining adequate drill coverage due to mine scheduling constraints and restricted access around underground openings; requirement for integrated systems to handle either blast hole or RC data; and development of effective methods to evaluate the performance of RC grade control. RC based grade control is delivering significantly improved lode definition, grade estimation and subsequent ore classification.

Jan 1, 2000

By H W. Scriba

The development and improvement of computer-based process simulation packages over the past 20 years has provided process engineers with a powerful tool to use in the design of complex metallurgical plants. The use of such modelling tools has enabled the design of process plants that minimise operating and capital costs whilst optimising plant efficiency and recovery. Almost every new project developed in the current market is underpinned by a simulation of the process. In line with engineering best practice this simulation should be based on laboratory/pilot plant test work results and sound assumptions. Any errors that are not identified in the development of the process simulation may have significant effects on the final design and operation of the processing plant. Developing a simulation of the process in a comprehensive, logical and auditable manner is thus essential in ensuring the simulation accurately represents the expected process plant behaviour. A methodology that ensures these requirements are met has been developed by SNC-Lavalin Australia and is described in this paper. The methodology includes the major review stages of data collection, model planning, model building and optimisation, model review, scenario testing and options development, and model reporting. All of these stages should incorporate comprehensive client interaction and review by a suitably qualified representative. In applying these methodologies SNC-Lavalin Australia ensures that the process simulation model developed can be confidently utilised in the design of the process plant, and in the estimation of operating and capital costs, whilst ensuring that engineering best practices are met.

Jan 1, 2008

By A He, J Li, J Pan, J Clout

The removal of sulfur from SO2 containing flue gas is improved by adsorbing SO2 into solution with manganese ions as catalyser, however, burnt lime slurry has to be added to modify solution pH and the CaSO3 by-product is of low economic value. In this paper a novel one step process for simultaneous manganese leaching-desulfurisation of flue gas is presented. An investigation of the effect of process parameters included flow rate and SO2 concentration in flue gas, adsorbing time, solution to solid mass ratio, leaching time, and their impact on the oxidation and removal of SO2 from flue gas. The catalysing mechanism of manganese ions on the oxidation and SO2 removal was demonstrated by calculation of the species originating from manganese ions and SO2 in the solution according to solution chemistry. SO2 removal in the adsorbing solution took place at pH 5 - 6, where manganese ions dominantly occurred as Mn2+, and the chain reactions for oxidation of SO2 starting from HSO3- were improved by the presence of Mn2+. SO2 bearing flue gas was effectively desulfurised by leaching rhodochrosite (MnCO3), with desulfurisation of the flue gas and modifying the solution pH being achieved simultaneously, and MnSO4 of high economic value recovered from the leachate. 85 per cent manganese leaching and over 70 per cent desulfurisation of the SO2-bearing flue gas were achieved with only one adsorption stage under optimum conditions.

Jan 1, 2004

By R J. Everett

The mining industry is beginning to adopt quality systems based on the requirements of International Standards for quality assurance, such as the ISO 9000 series. Indications from similar industries are that considerable benefits are to be had from their adoption. This paper describes the use of the International Standard ISO 9001 for quality assurance within BUKA Minerals Limited. This provided guidance for the development of a clear statement providing agreement on the processes to be followed and the outputs required when dealing with outside service providers. Discussion focuses on the interaction with BUKAÆs consultants and contractors during the specification stage, resulting from the application of quality assurance techniques. Risk analysis was used to identify and manage the risks associated with the companyÆs contract for geotechnical and mine design services and the tender for a mine development program of work during the feasibility stage of the project. Setting acceptance controls for the deliverables from such contracts is traditionally fraught with difficulty. BUKA used Failure Mode and Effect Analysis for exposing underlying risks that were not effectively being countered. The briefs were reviewed and additional controls were developed to manage the risk. These controls have provided clearer instructions to the consultants and contractors, indicated audit points for the company and defined the deliverables. There exists within the company, and among its outside service providers, a clearer understanding of what is to be achieved and how it will be measured. The process has imparted considerable confidence to both parties on how the work will proceed and what outputs are to be provided. Some discussion is provided on how quality principles are being applied throughout industry and commerce, generally, and how they may apply to the mining industry. The paper argues that, far from being an appendix to the tendering process, Risk Management should be a mandatory step integrated into the definitions of the work.

Jan 1, 1998

By D C. S M, J Skudder, R F. Sandenbergh

Metallic sulfide minerals present in most gold ores, Morila gold ore included, often decompose under typical gold leaching conditions. The reactions and their products consume oxygen and sodium cyanide, consequently competing for oxygen and cyanide used in gold dissolution. The resultant effect is to reduce both the kinetics of gold dissolution and overall extraction efficiencies. The present paper discusses results obtained from plant data analysis and laboratory work investigating the problem of higher than expected consumption of sodium cyanide at Morila Mine Gold Plant. Cyanide consumption at the Morila Mine Gold Plant had been consistently running at 46 per cent higher than the expected value without any corresponding increase in gold recovery. In fact, plant data analysis showed an inverse relationship between cyanide consumption and grind, as well as cyanide consumption and gold recovery. Experimental and plant data analysis indicated that better control of the [CN-]/[O2] ratio is necessary for the efficient use of reagents and achievement of higher gold recoveries. Careful control of this ratio at a minimum of eight enabled the reduction of sodium cyanide consumption by 200 g/t, that is, from 650 g/t to 450 g/t. Coupling these experimental conditions with the addition of lead nitrate at 100 g/t improved the overall gold recovery to 93 per cent compared to the average plant recovery of 90.2 per cent over a six-month period. This improvement was also reflected in the leaching kinetics where 70 per cent gold extraction was achieved after four hours, as compared to 59 per cent in the absence of lead nitrate addition. Also of great importance is the fact that the combination of hydrogen peroxide and oxygen gave inferior performance relative to either of the two reagents used separately. This scenario presents an opportunity for excluding hydrogen peroxide, an expensive reagent, and focusing on improving the oxygen addition system to boost dissolved oxygen concentration in the plant.

Jan 1, 2007

The Queensland Phosphate Limited (QPL) Project is based upon the manufacture on world scale of High Analysis Fertilizers from resources located in north-west Queensland.High Analysis Fertilizers are produced from phosphate rock, sulphuric acid and ammonia.

Jan 1, 1993