Search Documents

By K Koskinen, S Ronkainen

The flow field induced in an Outokumpu TankCell and by an OK rotor-stator mixing device in a laboratory and a process size flotation cell was modelled numerically using computational fluid dynamics (CFD). The primary target was to discover and reproduce the various interactions between the flow field and the flotation cell by numerical means. As power consumption depends sensitively on flow field, it can be regarded as a top-level derived quantity (or measure/metric) indicating the validity of the numerically obtained flow field. Having properly validated numerical means to produce the flow field the influence of various design parameters can be captured with certain accuracy. In addition, separate gas and solid phase models for bubbles and solids, respectively, were implemented. The comparisons between velocities and turbulence quantities measured using the laser doppler velocimetry (LDV) technique and CFD modelling were performed. The grid generation was performed with the commercial Gambit 1.3 and the subsequent integration and solving of the resulting algebraic equations with the commercial CFD-code Fluent 6.22. The computationally economic multiple reference frame method was included to model the moving rotor blades. Gas and solid phase models were modified mixture models.

Jan 1, 2005

By Swift D. G

For some time the Electricity Trust of South Australia (ETSA) has been investigating the application of new mining methods and equipment to minimise the cost impact of the steadily increasing depth of mining brought about by the 20¦ dip of the coal seams at the Leigh Creek Coalfield. Exhaustive examination of all suitable mining systems showed that highly mechanised systems involving belt conveyors displayed no eco- nomic or operational advantages over shovel and truck methods. However, the configuration of the Leigh Creek coalfield allows for two quite different approaches to mining by shovel and truck. The current strip mining method involves removing overburden from the highwall in 60 m to 200 m wide strips to progressively expose the coal down dip, and requires all waste to be hauled to the surface. The alternative ter- race haulback method involves opening a boxcut to full depth at one end of the coalfield, then mining the full section along strike and placing the spoil in the mined out area. On a strictly economic basis, the latter is clearly advantageous, but the former has significant less tangible advantages. In deciding between the two methods ETSA is faced with the need to examine the applicability of each method under a wide range of possible future demands on the coalfield, and to assess the importance of many intangible factors.

Jan 1, 1989

By N Patzelt, T C. Logan, I B. Klymowsky

In 2003, NEWMONT MINING CORPORATION, the worldÆs largest gold producer, set out to prove that High Pressure Grinding Roll (HPGR) technology is sufficiently robust and reliable to be considered for the treatment of hard rock gold ores. In collaboration with POLYSIUS, a significant trial was conducted and 127 600 tonnes processed, successfully proving the HPGR capabilities on the Lone Tree Mine, Nevada ore û one of the most competent and abrasive ores in the industry. The success has led a number of mining companies to consider HPGRs for the comminution of gold and copper ores.

Jan 1, 2004

By Miskelly N

In Australia and New Zealand, the 'Australasian Code for Reporting of Identified Mineral Resources and Ore Reserves', which was released by industry in 1989, is operating successfully in a co-operative approach between industry and regulatory authorities. Similar codes or guidelines exist or are under development in the United States of America, Canada, the United Kingdom and South Africa, although the regulatory backing given to the Australasian Code is unique. International standard definitions for Mineral Resources and Reserves, and for categories of Resources and Reserves, have been under development by the Council of Mining and Metallurgical Institutions since 1994 and have already stimulated considerable convergence of definitions and reporting standards in participating countries. It is hoped that agreement on this international standard for public reporting by mining companies will be reached within the next two years, and it is expected that adoption of the standard will result in a higher and more uniform quality of reporting worldwide, with a consequently greater interest on the part of the general public and financiers in investing in the mining industry.

Jan 1, 1997

The Copper Concentrator at Mount Isa Mines Limited treats approximately 6 Mt of chalcopyrite ore annually. The ore is currently sourced from the 1100 and 3000 orebodies at Mount Isa. Chalcopyrite is the only significant copper bearing mineral, with pyrite, quartz and dolomite being major gangue minerals. Ore is typically 10% chalcopyrite, 11% iron sulphides and 79% non-sulphide gangue. Copper ore is treated through two autogenous mills, two ball mills and a flotation circuit. The autogenous mills replaced a crushing plant, two rod mills and two primary ball mills during 1991. For routine analysis of concentrator performance, composite samples of mill feed, final concentrate and tailings are generated every 4 week period. All samples are sized and size fractions are assayed. Recovery of mineral species to the concentrate are then calculated for each size fraction. Sometimes liberation analysis was also performed by QEM*SEM (Quantitative Evaluation of Material by Scanning Electron Microscope).

Jan 1, 1990

Past and present developments in the use of blast furnace slag in the manufacture of glass are outlined. The crude slag from Port Kembla is beneficiated by the Mineral Resources Division of Australian Consolidated Industries Ltd. at Mascot using a dry magnetic separation process which reduces the iron level in the slag to an acceptable value, The chemical and physical properties of both the crude and beneficiated slag are given and compared with those of other slags used in the manufacture of glass. Slag is added to intro- duce alumina into the glass and its addition to the glass batch also results in faster melting and refining. Slag was first used in Australia in 1968 and its use has increased steadily year by year. At present about 16 000 tonnes of slag are used per year, mainly in amber and white glass. Beneficiated slag is used'in three plants to supply all the alumina required in the amber glass and in four plants to supply part of the alumina required in the white glass, the amount added depending on the acceptable iron level in the glass. Slag is also used in limited quantities in the manufacture of both dark and light green glass.

Jan 1, 1979

The Sydney Coalfield, Nova Scotia contains extensive undersea longwall mining operations which are expected to continue well into the 21st Century. A long term research program has been initiated by the Cape Breton Coal Research Laboratory to investigate the full spectrum of problems associated with undersea mining and develop specific guidelines for use by the mine operator. At present, research is centred on the detailed evaluation of existing undersea sub- sidence guidelines, the identification and development of instrumentation capable of moni- toring seafloor subsidence profiles and the effective sealing of offshore exploration boreholes. In addition, work is also planned to examine in situ strata permeability changes occurring between the mining horizon and seabed and the feasibility of using artificial islands.

Jan 1, 1986

By E Villaescusa

This paper describes a methodology for the design of mine pillars at the McArthur River Mine. The pillar strength is calculated using a method that accounts for confinement, pillar geometry and intact rock properties. The average pillar stress was calculated using in situ measurements of vertical stresses at shallow depth and the tributary area method in conjunction with numerical modelling. Observations of pillar behaviour indicate that an existing pillar stability graph may be slightly conservative and further adjustments for the local rockmass conditions are needed. The results to-date indicate that all mine pillars are stable for a range of mining geometries at McArthur River Mine.

Jan 1, 1998

By Seedsman RW, Duncan Fama ME

Mine design procedures will be revolu- tionised by technological developments in computers, software, database construction and management, and numerical modelling programs. Developments in geotechnical databases will be required which utilize geological and geomechanical tests to supply appropriate input for numerical models. Techniques utilizing sedimentological and structural modelling are described. The capacity of current numerical models in mine design is outlined and a program for developing a fully integrated mine design package proposed.

Jan 1, 1987

The mine planning and operational aspects of applying Continuous Surface Miner (CSM) technology to Australian coal strip and open cut mines is investigated for both existing and planned deposits. CSM produc- tivity as a function of geomechanical properties, formation thickness, mechanical availability and in-pit physical constraints, are considered. Productivity and operational costs are derived from current production machines and from first principles.

Jan 1, 1989

By Fuerstenau DW

The flotation of pyrite in ethyl xanthate solutions is presented along with electrokinetic results. The results have been analysed in view of recently published thermodynamic calculations as well as other published data on the pyrite-xanthate system including adsorption and voltarnmetry studies. The flotation response of pyrite in xanthate solutions is characterised by two maxima, one at pH 4 and the other at pH 8-9. The acidic maxima is also associated with a reversal in the electrophoretic mobility of pyrite, probably due to the formation of ferric xanthate on the pyrite surface through chemisorption of xanthate ions while the basic maxima is not associated with major changes in the mobility and flotation at this pH can probably be attributed the adsorption of dixanthogen. It is concluded that there is not sufficient experimental evidence to conclusively attribute the lack of flotation response in solutions at near neutral pH to any particular phenomena, either kinetic or thermodynamic.

Jan 1, 1993

By Simpson D, Skopakow J

This paper is one of the series of papers relating to the Melbourne Underground Rail Loop and specifically describes the structural and architectural design of Museum Station. Structural arrangement, loads and design methods of the major temporary and permanent works are briefly described for the main station and entrance works. Planning of the station concourse area, booking halls and entrances are described together with the selection of finishes for all above and below ground areas.

Jan 1, 1981

A great part of the research on froth flotation of gold ores deals with ores containing gold associated mainly with sulphides, resulting in a largely accepted view that what takes place with sulphides (eg pyrite) in a flotation cell also happens to gold particles. This paper is concerned with the influence of some inorganics (CuSO4, CaO and NaCN) on gold particles flotation, using ethyl or amyl xanthates as collectors. The bench-scale tests were carried out with ground quartz and gold particles mixtures. Some findings stemmed from this study: flotation of the gold particles of size 0.16 mm was efficient adding only frother; larger gold grains were better recovered by the use of stronger collector CuSO4 did not seem to be an activator for gold; the addition of NaCN up to 200 g/t or CaO up to 2000 g/t did not depress the gold grains when amyl xanthate was used as collector although with ethyl xanthate the gold depression was verified.

Jan 1, 1993

The Coal Section of the Geological Survey of Queensland was formed in 1950 to plan and supervise systematic diamond drilling programmes to investigate the State's coal resources. For the first 15 years these programmes were con- fined to the established coalfields to prove reserves of coal suitable for steam raising for power generation. Adequate reserves were del- ineated during this period to provide coal for the operating lives of new power stations at Ipswich and Collinsville. Later exploration was aimed at a regional appraisal of coal mea- sure stratigraphy, particularly in the Bowen and Galilee Basins. This was followed, in some areas, by drilling to prove reserves to indic- ated status. Parameters were developed to allow a uniform approach to the estimation of reserves. Coal quality is evaluated in terms of potential utilization of coal. Reserves defined by exploration companies are assessed, and combined with reserves from Departmental drilling into a general table. Total reserves in situ amount to 9 962 million tonnes of coking coal and 7 333 million tonnes of non-coking coal. Approximately 20 per cent of coking and 40 per cent of non-coking coal were proved as a direct result of Geological Survey drilling programmes. Further explor- ation is planned for the Bowen and Galilee Bas- ins and may extend to the Surat Basin.

Jan 1, 1977

The present geology of the northwest quadrant of the Circum-Pacific is the product of the interact-ions between plates or paleo-plates which have oc-curred since the earliest part of the earth's hist-ory. Almost every possible geologic structures are observable there; stable continents, collision belts, and subduction arcs as well as extensional basins. This suggests that almost all the possible tectonic processes occurred through geologic time and the present overall structure of the Quadrant is no more than a time section of the long lasting tectonic history which the region experienced.

Jan 1, 1990

The purpose of this paper is to outline the equipment used for diamond drilling at Mount Isa, together with alterations and recent improvements therein. As the majority of the drilling is carried out with machines running at relatively high speeds using XRN blast hole bits, the paper is mainly devoted to this branch of drilling.Because diamond bit costs constitute the major expense, a considerable amount of research into bit design has been carried out, and in several instances, costs per foot have shown an appreciable decrease in spite of rising manufacturing costs and higher diamond prices. Equipment performance has at times been erratic due to delays in delivery and occasionally because of faulty parts, but in general the position has improved by keeping in close contact with the manufacturers.BLASTHOLE DRILLING MACHINESThe standard blasthole diamond drill is the 'E-500' two cylinder air powered model manufactured by Mineral Drillers Limited. Several of the older pattern JV41 are still in use, but are being retired as they wear out.. Machines are repaired in the underground diamond drill shop.The normal feed gears used when drilling in lead shales are 350 top gear and 450 low gear-actually 357 and 438 revolutions per inch of advance respectively. The 300 gear was commonly used several years ago, but it was found that bit footages could be increased without any appreciable drop in penetration rate by reducing to the 350 gear. Gears used for copper drilling are 650 and 750. Footage per shift...

Jan 1, 1953

Modelling of Synergistic Effect of Cyanex 302 and D2EHPA in Zinc Solvent Extraction A comprehensive model is presented to predict the synergistic effect of D2EHPA and Cyanex 302 on co-extraction of zinc and manganese. The experimental results indicated that pH, temperature and the extractants ratio have strong effects on the extraction process. Correlations were proposed to predict the distribution coefficient of zinc and manganese between two phases at different conditions by multiple linear regression. The correlations were simplified by eliminating less important terms by analysis of variance. Optimum conditions (ie pH, temperature, extractants ratio and aqueous to oil phase volumetric ratio) for obtaining maximum separation of zinc from manganese at different zinc concentrations and number of extraction stages were determined. For finding the optimum condition genetic algorithm was used. Comparison the model estimations and the experimental data show that the presented model has good ability to predict the behaviours of zinc extraction system over Cyanex 302 and D2EHPA.

Sep 13, 2010

By J Rostami, D Tadic

While hard rock tunnel boring machines (TBMs) have an established track record in the tunnelling industry, accurate estimation of TBM performance for each specific project remains critical. Machine performance prediction is required to assist planning activities, including costing and schedule preparation, machine specification and effective planning of maintenance and repairs. In addition, monitoring machine performance during the construction period is required to assess and manage excavation progress, and to achieve optimal advance rates based on specific geotechnical conditions exposed during excavation. TBM performance analysis can also contribute to the development of more accurate performance prediction models for future applications. Rock mass characteristics play a dominant role in machine performance. This paper offers a review of the impact of rock mass characteristics on TBM penetration rates for two specific tunnelling projects. A discussion is provided on the results of statistical analysis of available field data, including geological back mapping, rock properties and measured rates of penetration (ROP). The analysis offers a comparison of the achieved and predicted ROPs to provide a better understanding of the influence of rock mass properties on the performance of hard rock TBMs. A new rock mass adjustment factor is introduced to enhance the accuracy of an existing prognosis model for use in jointed rock masses.

Jan 1, 2008

By B Sno, P A. Cockburn, R C. West, C U. Jones

Clyde Materials Handling (CMH) and WorleyParsons have developed a concept for a flash furnace feed system using the specialist pneumatic conveying equipment expertise of CMH and the flash furnace process experience of WorleyParsons. CMH has developed a proprietary volumetric feeder (called a Rotofeed), which is extremely accurate and overcomes many of the problems inherent with loss-in-weight screw feeders and drag chain conveyors, previously regarded as state-of-the-art. Initial indications are that the Clyde-WorleyParsons feed system could deliver the following benefits to flash furnace operation: accurate pulseless delivery of feed material to the head of the burner leading to improved combustion performance and process stability; highly accurate split to the individual quadrants of a conventional burner tube, or provision of a smooth hollow curtain to a burner without guide vanes; decreased pressure pulsation in the furnace due to improved combustion control and performance; and decreased temperature fluctuations in the furnace due to improved combustion characteristics and hence reductions in refractory thermal stress and wear.

Jan 1, 2005

This paper deals briefly with the geology and mineralisation of the Ediacara Mineral Field, which is located about 300 miles north of Adelaide in the Mount James Range.The field was discovered sane time prior to 1872. Total recorded production for the field amounts to a few hundred tons of lead and 36 tons of copper. Re-listing of the field during 1961-62 led to its classification as a Mississippi Valley type deposit. Diamond drilling has partly outlined the spread of mineralisation and confirmed its stratiform distribution,Sources for the metals are suggested and various possible mechanisms. of deposition are described.

Jan 1, 1963