Search Documents

By Jackson S

An investigation into different aspects of importance in the understanding of explosibility of hybrid mixtures of coal dust, air and gases potentially found within mine workings through a comprehensive laboratory program of explosibility tests was conducted. Plotting of test results revealed that conditions of potential explosibility could be described using two dimensional flammability limit surfaces- for coal dust/oxygen; methane/oxygen; and coal dust/methane mixtures. From these plots, the three dimensional flammability envelopes defining the explosibility of the coal dust/methane/oxygen mixtures can be defined and illustrated for a coal sample. The surfaces of the three dimensional envelope describe limits which separate inert mixtures of coal dust and methane at varying oxygen levels from those concentrations which are ignitable under defined conditions. It is considered appropriate to generalise that the geometric shapes of these limit regions are applicable to all type classifications of coal dust. There are practical applications of these results to the underground environment.The action of free radical initiators in the propagation of a methane gas explosion was examined for its applicability to the flammability of coal dust/gas/air mixtures. The oxides of nitrogen or NO x radicals have influence upon the lean limits of flammability of hybrid mixtures and this is illustrated by use of three dimensional coordinate geometry. Gases can be introduced to the underground environment through the exhaust gases of diesel equipment. It is concluded that radical species can substantially increase the flammability of gas and dust flames and as a consequence raise risk of mine atmosphere explosibility.

Jan 1, 1998

Krupp Polysius AG, FRG, in close cooperation with Prof. Dr. K. Schoenert, FRG have developed the principle of the high pressure grind- ing roll POLYCOM. The POLYCOM mill basically consists of two counter-rotating rolls of large diameter and relatively small width, one of which is fixed and the other moving in slide blocks. The pressure required for comminu- tion is applied via the sliding roll by a powerful hydraulic system. The comminution takes place between the rolls under high pressure in the bed of material by nipping and compacting. The top feed size-depending on the rolls diameter -may be as coarse as conventional secondary crusher feed and the product is a compacted cake containing a high amount of fines created by micro-cracking. The amount of fines depends on the pres- sure (grinding force) applied. Operating results show that even in wet griding circuits capacity increases at downstream connected grinding mills of up to 100010 can be accomplished with an interconnected POLYCOM machine and energy savings of up to 25070 may be achieved depending on application. POLYCOM can be used in existing grinding plants for low-cost upgrad- ing of capacities but also as an advanced alternative to conventional crush- ing and grinding equipment in open or closed circuit configuration. A single industrial size 2.8m roll diameter POLYCOM machine may be fed with top feed size of up to 200mm and produce a finish product as fine- grained as known from rod and ball mills but with less energy consumption. Meanwhile, the POLYCOM high pressure grinding roll has established itself world-wide in the cement industry and is now entering the mining industry. POLYCOM machines are currently designed in industrial standard sizes of 1.0m to 2.0m rolls diameter and drive units of up to 2400 kW. This paper includes: principles of high pressure grinding, main fea tures of the POLYCOM machine, results of tests on various materials including Australian gold and copper ores carried out at the POLYSIUS research centre in Germany. Some examples of industrial applications of high pressure grinding will also be presented.

Jan 1, 1988

By Hilde TWC

Synthesis of GLORIA side-scan sonar and other geophysical data has provided morpholo- gical and tectonic details of the interaction between the Nazca and South American plates along the Peru Trench (80S-15¦S). Our analyses suggest that a new propagating rift of the Galapagos type is evolving along the Mendana Fracture Zone (MFZ). Subduction induced rift- ing of the Nazca plate is accompanied by organized seafloor spreading for the last 3 Ma at least. GLORIA sonographs and bathymetric mapping show an 8-10¦ divergence in MFZ width towards the Peru Trench. The fracture zone comprises numerous ridges and troughs and a lack of sediment cover in the axial part. Young magnetic lineations (anomalies 1-2A) are observed within the fracture zone wni.cn are orthogonal to the older Nazca plate lineations. The central anomaly narrows west- ward and can be observed up to 400 km seaward of the trench whereas anomaly 2A is terminated about 200 km from the trench axis. Recent SeaMARC II sonar mapping in the region shows large igneous blocks in the Trench axis to the north of MFZ but absent to the south. We believe these blocks represent young seafloor of MFZ rift/spreading center broken off from the ridges as they subduct along the Peru Trench. The MFZ rift is propagating west- ward at a rate of 115 km/Ma (25 km/Ma relative to the South American plate). Given the present rates of accretion at the East Pacific Rise and of propagation along MFZ rift, the Nazca plate will be divided into two parts in about 35 Ma.

Jan 1, 1987

The occurrence of metallic minerals in Australia to the time of the proclamation of South Australia as a Colony in 1836 was unknown. It is, therefore, perhaps, surprising that British settlers arriving in the Coromandel included among their number a German scientist Johannes Menge who had been appointed by the South Australian Company to the post of Mine and Quarry Agent and Geologist on 1 July 1836. His instructions were to `explore the natural productions of the Colony above and below ground and to superintend the working of quarries of stone and slate, the boring for water, metal, lead, coal and other mines at a salary of ú150 per annum for one year and for as much longer as the Company require your services not however exceeding five years'. In the event, he was to have little influence on those matter.

Jan 1, 1993

By Hendrix J. L, Nelson J. H

A study was conducted to examine how pretreatment of carbon-bearing gold ores with chlorine enhances gold recovery by cyanidation. It is hypothesized that metal species (including iron and copper) dissolved during chlorination adsorb on the carbon surface hindering the adsorption of dissolved gold. To test the hypothesis, samples of several sulfide minerals were subjected to reaction with sparged chlorine gas to determine which, if any, dissolve faster than gold under these conditions. Then, a synthetic carbonaceous refractory gold ore containing pyrite, chalcocite, activated carbon, and gold was subjected to gas sparging. The results of these experiments showed that chalcocite and arsenopyrite dissolve so that metal (copper and iron) is put into solution slightly faster than gold under the same chlorination conditions. Also, it was observed from the experiments that gold adsorbs on activated carbon during chlorination, but is replaced by copper and iron as the chlorination process dissolves more of the chalcocite and pyrite. The study concluded by investigating ferric chloride addition prior to chlorination to hinder gold adsorption on activated carbon.

Jan 1, 1991

TUNGSTEN occupies an outstanding position amongst metals to-day, for by its use modern manufacturing methods have received a wonderful impetus. The important part played by tungsten in the recent war is not generally recognized. It was tungsten steel, in the shape of highspeed tools, that kept our soldiers supplied with munitions of war at more than one critical period. Tungsten added the necessary hardness and durability to various metals which were indispensable for carrying the war to a successful conclusion. In the words of...

Jan 1, 1921

Investigation on Sheelite Floatability by Particle Size Fraction

Sep 13, 2010

By Ketteridge IB, Mulcahy DE, Quast KB

The long term energy demands in South Australia are such that there is a distinct possibility that one of the lignite deposits in the State will be exploited to feed a pulver- ised-fuel power station. Bowmans lignite deposit is the largest lignite deposit in South Australia and is considered to be a contender. The deposit is ideally situated (100 km north of Adelaide) but the quality of the lignite is poor (see Table 1). TABLE 1

Jan 1, 1984

By Bogar D. V

Often dewatering of coal tailings is inhibited by the presence of clays, making it difficult to obtain a high concentration, handleable coal tailings. The net result can be a low concentration, chocolate mousse-like tailings which poses significant sedimentation problems in a tailings dam and represents a significant environmental problem. This paper examines the coal tailings from a Hunter Valley colliery where the tailings properties are influenced significantly by the presence of montmorillonite clay. The influence of the calcium ion on the rheology and sedimentation/compression behaviour of coal tailings . containing montmorillonite already dispersed in water was investigated and revealed that very little improvement in the properties is achieved through the coagulation. The preliminary investigations also indicated that the properties of the tailings were dominated by the presence of the montmorillonite clay. Thus investigations were carried out on the clay alone in water. Investigations into the effect of dispersing samples of the clay alone in water and then coagulating with calcium compared with dispersing the clay directly into calcium ion solutions at the same calcium concentration showed huge improvements in the rheology, compressibility, sedimentation rates and sediment solids concentrations for the second dispersion method, which can be called controlled dispersion. The sediment volume fraction solids improved by more than a factor of two by controlling the dispersion of the clay. The reason for the improved properties lies in the suppression of the initial swelling of the clay, which is initially in the sodium form, thus maintaining the parallel orientation of the platelets that is present before wetting. While swelling is being suppressed, ion exchange occurs with the calcium which results in permanent swelling suppression. In the uncontrolled dispersion case where swelling is uninhibited, the clay is allowed to break up and despite the powerful coagulating nature of the calcium ion, the random orientation of the high aspect ratio clay platelets inhibits effective coagulation. Results indicate that the initial electrolyte concentration of the washwater in a coal washery is the critical factor controlling the dewaterability of clay tailings and the handleability of the dewatered product rather than the actual act of coagulating with the calcium ion. The results presented are of clear practical significance and indicate how coal tailings problems where clay dominates the rheology can be improved considerably by knowledge of the surface chemistry.

Jan 1, 1995

A review of major mineral processing and extractive metallurgical developments is made and current areas for research are discussed.

Jan 1, 1975

A synthetic gold-silver telluride material (mainly sylvanite) has been prepared and its physical and chemical properties checked. Flotation tests using a Hallimond tube were conducted using commercial xanthate collectors. At collector concentrations of 10-3M with the addition of 5 × 10-4 M CUS04, no obvious differences in the mineral recoveries were seen irrespective of whether amyl, secbutyl, isobutyl or isopropyl xanthates were used. However, when the concentration of xanthate was reduced to 10-4 M or in the absence of the copper sulphate activator, the effectiveness of the collectors was in the order: amyl > secbutyl > isobutyl > isopropyl > ethyl. Changes in the slurry pH appeared to have little effect on the recovery of the telluride mineral.Leaching tests of the precious metal telluride showed that both gold and silver dissolve in alkaline oxygenated cyanide solutions but at a much lower dissolution rate than metallic gold or silver. Both leaching tests and electrochemical measurements indicate that the dissolution rate of gold-silver telluride is controlled by the pH and cyanide concentration of the leachant.Roasting the gold-silver telluride materials in air at temperatures between 550 and 750°C resulted in its decomposition into a metallic gold-silver alloy and tellurium dioxide.

Jan 1, 1994

By A Chandra, P Guj

Only a few complex real options can be valued using closed-form equations, such as the Black and Scholes formula, because these algorithms are restrictive and prevent the construction of practical project evaluation models. Although a binomial lattice method paired with the ærisk-neutral probabilityÆ provides an easier and flexible modelling of exploration and mining projects, it has limitations when projects are complex, long-lived and influenced by the interplay of various market and private uncertainties. In order to overcome these limitations, modern decision tree software using dynamic programming capability can be used for real option valuations. This is a powerful computational tool in which the impact of various sources of uncertainties can be differentiated, so that the optimal decision path can be explicitly displayed visually. There has been significant academic controversy surrounding whether different real option (RO) valuation methods would lead to different real option values (ROV). This paper, using a realistic copper mining example, demonstrates that as long as the same degree of subjectivity and consistency are used in different real option valuation methods, they yield the same result. This conclusion is valid irrespective of whether the cash flow volatility generated by various sources of uncertainties is handled in an aggregated or in an explicit and differentiated manner. This paper compares two choices for an investor either to æbuy now and developÆ a project or to enter into a ætwo-year option to purchaseÆ after the proponents have developed it. It also shows how significantly different net after-tax operating cash flows may be generated by these different choices on the same underlying asset represented by the project. This is due to the difference in the amount and timing of the relevant capital investments affecting the depreciation and amortisation charges and as a consequence, the income tax paid. CITATION:Guj, P and Chandra, A, 2012. Real option valuation of mineral exploration/mining projects using decision trees - Differentiating market risk from private risk, in Proceedings Project Evaluation 2012 , pp 177-188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

The Nickel Rim Depth Cu-Ni-PGE deposit, discovered by Falconbridge Limited in 1993, illustrates several trends in exploration in the Sudbury area. Recent discoveries tend to be deep, high grade, footwall hosted, close to or straddle property boundaries and made using a multi-disciplinarian exploration approach that integrates economic considerations with geology, metal geochemistry and geophysics (borehole EM). The Nickel Rim deposit occurs down dip of Inco's Victor Deep deposit (4.2 million tonnes at 2.25 per cent Ni, 7.30 per cent Cu) in the eastern margin of the Sudbury Igneous Complex (SIC) at a depth of 2650 m. Before commencing drilling an economic evaluation was done to determine the minimum size needed to be economic at the expected depths and determine the expected value of an exploration venture. The subsequent surface exploration program discovered a drill indicated, undiluted mineral inventory of 1.6 million tonnes of 1.58 per cent Ni, 10.13 per cent Cu, 4.17g/t Pt and 3.50 g/t Pd including 519 000 tonnes of 4.13 per cent Ni, 25.53 per cent Cu, 9.76 g/t Pt and 8.42 g/t Pd. The deposit is hosted by gneiss, migmatite, gabbro and pseudotachylite (Sudbury Breccia) 100 m below the base of the SIC.

Jan 1, 1996

By N Boughen, P Ashworth, S Johns, C J. Yeats, A Littleboy

The ocean floor, often called the last frontier, is increasingly discussed in terms of its resource potential û from near shore building aggregate and placer deposits to massive sulfide orebodies in the deeper ocean. Consequently there is an increasing incentive to mine the seafloor. But, do we have the social license to explore and mine the seafloor? Does this nascent industry have support amongst the wider community? If not, why not? And what should be done? To answer some of these questions, the Wealth from Oceans National Research Flagship has explored the social viability of an expanded seafloor exploration and mining (SEM) industry inAustralia. The results show that there are significant geological and environmental data gaps and that, in the absence of sufficient information, stakeholder reaction to the prospect of an SEM industry expansion may be reactionary and negative. This uncertainty means that the perception of risk from the industry is variable and often dependent on individual values. The acceptability of an expansion to the SEM industry is currently precarious, in particular due to the high levels of uncertainty regarding the environmental impacts of seafloor activity. While there are existing federal regulatory frameworks and government processes for the licensing of seafloor mineral exploration and extraction, there is little precedent in the application and implementation of these regulations. The future viability of the industry will be highly dependant on AustraliaÆs ability to improve the knowledge-base underpinning its regulatory regime and also to generate open and transparent communication channels between stakeholders. It will also be dependent on the SEM industryÆs ability to communicate an acceptable value proposition to society. This proposition will need to include the relative impacts of terrestrial and marine mining, the alternative potential uses of the ocean and the multi-use conflict that SEM might engender. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Mount Isa Mines Limited has been mining copper ore for 50 years. In recent years, this production has been entirely by open stoping methods with cemented backfill, mostly in the large 1100 orebody.This has been the major ore source for 20 years, with smaller amounts coming from the 400, 500, 650 and 1900 orebodies. At present, the 1100 orebody is the only source, and this situation will continue until the deep 3000 and 3500 orebodies begin producing in late 1992/93. Production rates have increased to almost 6 Mt/yr, and are planned to rise to 7 Mt/yr by 1995/96. In the future, there will be a move towards variations of the open stoping system as production moves to more lensy zones of the southern 1100 orebody and to the deeper 3000 and 3500 orebodies. This paper describes current operations in the 1100 Orebody, with some indications of future directions.

Jan 1, 1993

An understanding of the way that solutes are transported in mining or natural environments is essential to the development of sound strategies for managing waste disposal. Research on miscible pollutant movement in unsaturated porous media is carried out both experimentally and numerically. Results of numerical modelling are obtained by solving the groundwater flow equation and the solute transport equation. The finite element method is employed and comparisons between simulation results and experimental data are found in remarkable agreement.

Jan 1, 1995

Interactive data exploration is essential for visualising grade distribution and geological controls on orbodies. Quick and appropriate computer techniques for making daily 'value adding' decisions include routine imaging of numerical data suc

Jan 1, 1998

By Fleming GJ

The Miwah prospect lies on the dilational 070¦ trending Miwah Lineament near its intersection with northerly oriented fractures within Pliocene volcanic rocks exposed between a NW trending segment of the dextral transcurrent Sumatra Fault, and the more northerly trending Samalanga-Sipopok Fault to the east. These faults reflect the continued interaction between stresses from the India-Australia plate located to the southwest, and spreading within the Andaman Sea to the north of Sumatra. A system of deep seated faults is believed to have facilitated emplacement of post-Miocene magmas and Quaternary volcanic centres at shallow crustal levels throughout northern Sumatra.

Jan 1, 1995

A method is proposed for the determination of antimony in ores. Antimony is volatilized as antimony iodide by heating with ammonium iodide at a controlled temperature.The fusion mixture is extracted with hydrochloric acid and the antimony content is measured by atomic absorption spectrophotometry using an air/ acetylene flame. The time taken for analysis when comparedwith existing fusion and separation procedures is considerably reduced. Cations and anions likely to be present in antimony ores were also studied for possible interference effects but were not found to interfere.

Jan 1, 1972

The Knelson Concentrator is a centrifugal gold concentrator developed in Canada, which utilises the combination of high gravitational ("G") forces and a unique fluidising action to efficiently recover free gold particles from minus 6 mm to fine micron gold in both alluvial and hardrock applications.Operating parameters including water requirements, fluidising pressures and feed rates are given, as well as an indication of their various effects on gold recovery.Results include a Colorado School of Mines Research Institute (CSMRI) report comparing the Knelson concentrator with various other gravity concentrators.

Jan 1, 1984