Search Documents

The issue of fine coal and tailings dewatering has become of increasing concern to many coal preparation operators, both in Australia and overseas due to a variety of factors. Increasing mechanisation and mining of thinner seams over the past decades has resulted in an increasing amount of fines generation while increasing international trade in coal and tighter environmental constraints on tailings disposal have resulted in the production of these same fines to be an increasing problem. However, technology to date has not always been able to supply a cost-effective solution to the handling of these fines in an efficient and environmentally benign manner. This paper will review the key issues associated with the dewatering of fine coal and tailings, will describe the major current practices and constraints, and finally will indicate alternative technologies that may have to be considered in the near future. For the purpose of this paper, "fine" coal is described as that material less than 0.5 mm in diameter (as this is the most common cutpoint between various plant circuits in Australian practice), although the technological constraints are very much dependent upon the fraction less than 45 micron. The amount of minus 0.5 mm material fed to plants varies, depending upon the type of coal and mining operation, but in Australia may range from less than ten per cent to greater than 30 per cent of the feed in higher rank coals.

Jan 1, 1991

By Rieniets S, Somerville J. L

In Morwell Open Cut brown coal mine, the overburden 'firehole' materials which have resulted from ancient coal fires vary-from hard baked clays to firm laminated lacustrine clays. The need to pre-strip designated areas to reduce the slope height and attain safe digging conditions for the bucket wheel excavator operation is now accepted practice at the open cut mine. In this study, the inherent spatial variability of undrained shear strength of the clay materials has been incorporated in a visco plastic, finite element based, probabilistic slope stability analysis. Data on the costs of initial pre-stripping, excavation and slope failure are collected to provide an economic basis for the optimisation of the design of the overburden batters in Morwell Open Cut. This improved stability modelling is enabling costly pre-stripping to be minimised while ensuring acceptable slope stability conditions and minimising the risk to personnel and plant.

Jan 1, 1994

The paper first outlines the conceptual basis for evaluating and controlling geological risk. Geological risk, the economic reflection of the uncertainties associated with tonnage, grade, and other pertinent deposit parameters, is evaluated in terms of economic risk criteria. Delineation provides the deposit information required to appraise and control this risk. The improved reliability of geological estimates resulting from additional delineation reduces the economic risk associated with mine development and production decisions. However, the benefits of delineation, subject to diminishing returns, have to be weighed up against the direct and time costs involved. These costs decrease base case economic values and shift the probability distributions of possible outcomes towards, lower values. The optimum amount of delineation normally is achieved short of the point where economic risk is minimised, depending on the mining company's relative preference for a higher base case value or a lower economic risk. Then, two open pit copper mine examples, based on actual situations, are analysed to illustrate the application of the concepts presented. The first case concerns the extension of ore reserves at an operating mine. Finally, a new mine development opportunity is considered.

Jan 1, 1994

By Patridge A. C

A pilot scale laboratory investigation of manual slurry sampling methods representative of those used in the minerals industry is described. Samples were taken from slurries made up from silica particles of various sizes and in various concentrations from a stirred tank and from the discharge lip of a rectangular launder. Sampling methods from the tank included immersion flasks and several configurations of a suction probe. The launder was sampled using a conventional narrow-mouth ladle and also with a 'mouth organ' stream splitter. Samples were analysed for overall solids concentration and size distribution and showed different but always significant and often large biases relative to the known overall composition of the slurry, the nature and extent of bias being dependent on pulp concentration, particle size, sampling method and sampling location. Results clearly show the very great difficulty of obtaining representative samples by simple sampling techniques, although the data suggest that errors can be reduced by using an appropriately designed and operated suction probe. Further work will be carried out with the objective of establishing guidelines for industrial sampling practice.

Jan 1, 1995

By Standish N

The heterogeneous reactions of carbonaceous materials with oxidising gases are basic to all combustion phenomena and to many gasification processes. The carbon- carbon dioxide reaction at elevated temperatures (Reactivity) plays important roles in many metallurgical operations like iron blast furnace and ferro-alloys smeltings, zinc and lead smelting, alumina reduction, cupola operation and direct reduction processes. The stoichiometry but not the mechanism of the reaction between CO2 and carbon is represented by the equation (Boudouard reaction) CO2 + C 2CO (1) This reaction is more complex than that between carbon monoxide and metal oxides, which involves essentially a transfer of oxygen from the oxide to carbon monoxide to generate carbon dioxide without any change in gas volume, whereas the volume of the product gas of Equation (1) is twice that of the reactant gas. In the present paper an attempt has been made to review critically the reactivity measurements of various carbonaceous materials in carbon dioxide atmosphere. Steps in C-CO2 reactions, surface reaction mechanism, role of mass transfer on reaction kinetics, dynamic oxygen exchange reaction and rate equations and rate controlling steps are discussed. Various methods of reactivity measurements with their pros and cons are also presented. Effects of pertinent process variables on the reactivity of carbon are also described in detail.

Jan 1, 1986

By V Lickfold, A J. Crawford, A J. Wilson

A total of 12 alkalic porphyry centres of Late Ordovician age have been discovered in two mineral districts within NSW. The alkalic porphyry deposits are hosted within shoshonitic volcanic centres that formed where a major cross-arc basement structure (the Lachlan Transverse Zone) cut the Ordovician Macquarie Arc. The Macquarie Arc was amalgamated with the back-arc basin sediments of the Wagga Marginal Basin and with the proto-Pacific margin of Gondwanaland to form the Lachlan Fold Belt after the cessation of arc magmatism in the Late Ordovician. Within the Ordovician volcanic belts of NSW, the alkalic porphyries are the most significant mineral deposits economically. The combined resource of the Cadia district porphyries (729 Mt @ 0.79 g/t Au and 0.30 per cent Cu) makes Cadia the worldÆs seventh largest known porphyry gold system and the largest known gold resource in an alkalic porphyry system (574 t Au). Hydrothermal alteration in the alkalic porphyries comprises a complex sequence of potassic, calc-potassic, sodic, calc-sodic, propylitic and late-stage, typically fault-controlled phyllic assemblages. Hematite dusting is common in many of these alteration assemblages, giving the intrusions and the altered volcano-sedimentary host sequences a distinctive pink-orange colouration. Intensely developed hydrothermal alteration assemblages are localised to within a few hundred metres of the composite intrusions that sourced the mineralising fluids, making these deposits difficult exploration targets. Sulfides are typically zoned, with several of the deposits having bornite-rich cores, chalcopyrite-dominant annuluses and pyritic outer haloes. Gold is well correlated with bornite in most of the deposits, and with chalcopyrite at Cadia Hill.

Jan 1, 2002

By Godresse M, Turczynski G. P J, Driver I. J, Low G, Ozawa N

Geological evaluations of coal deposits have been traditionally undertaken in a somewhat manual manner. Information is collected downhole by chip sampling, coring and using downhole geophysical logging. This information is then interpreted by an experienced geologist to define the coal and noncoal lithological units. Coal units were subsequently correlated to provide data for structural modelling. In recent years a number of advancements in interpretation techniques have been made based on Artificial Intelligence. This paper describes an integrated geological interpretation system based on maximised use of Al techniques. The first part describes the lithological interpretation which uses a number of boreholes with both logged lithology and downhole geophysical logs. This information provides a learning set of data to the neural network. The second part concentrates on the correlation of both coal and noncoal units from borehole to borehole. Problems in this area, in a manual sense, are interpretation of correlation across weathering zones and other geological anomolies. The technique is based on pattern recognition and dynamic programming techniques where a correlation matrix is developed relating all holes with their maximum correlations.

Jan 1, 1995

By Firmin K

The Mt. Tom Price orebody of Hamersley Iron Pty. Limited consists of a folded hematite - shale sequence capped by a layer of goethite. Consequently, variations in iron content occur within the orebody, and as the overall grade is below that required to make specification products, selective mining must be carried out. A necessary preliminary to quality control'of products based on selective mining is the production of advance data, on the tonnages and grades of material to be expected in future mining areas. Bench plans showing zones of different grades and types of material anticipated are prepared from structural geological information. The grades of materials on a bench are essentially governed by the positions and attitudes of the shale bands. Quality control is exercised by blending different grades and types of material in primary crusher feed. Iron grade is the prime grade consideration although sometimes the level of phosphorus content must be considered. Pre-production grades Are determined from assay of samples taken from blasthole cuttings.

Jan 1, 1980

By Crawford M

During the initial development of Mount Isa Mines power was supplied from a temporary power plant situated near the Man & Supply Shaft. The main power plant was placed in service early in 1931 and then comprised two Babcock and Willcox boilers, fired by pulverised fuel, and two British General Electric Company's turbo-alternators of 5,000 kW. each. Both plants have been described by A. F. McAskill in the Journal of the Institution of Engineers, Australia.From 1931 power demand progressively increased due to greater production, further mine development in the harder sulphides increased pumping for mine drainage and additions to mill and smelter until, by 1935, the plant was inadequate for further output commensurate with a reasonable safety margin.Coincident with the added power demand, operating conditions involved a fuel problem which could not have been anticipated. The ash content of the fuel supplied gradually increased from 13% to 16-5%, while the melting point of the ash decreased with higher pyrite content.Temperature conditions in the furnace required careful control to cope with ash formation and slag accretions.Consequently brickwork, excessively stressed on water walls, was constantly under repair, and required suspension periods of 50% of operating time for cleaning and overhaul.Load conditions varied continually, therefore the high heat liberations in the furnace, necessary to accommodate peaks in fluctuating output, resulted in ash fusion.

Jan 1, 1939

By Gillies A. D S, Just G. D

The advancement of computer applications in the coal industry is focusing interest on the presentation of washability data by mathematical functions.The normal method of presenting washability data is in the form of five curves, usually filled by eye or by cubic spline functions. It has been shown that coal washability can be characterised by two basic relations: the instantaneous ash vs relative density relationship and the instantaneous yield vs relative density relationship. In a new approach to the mathematical modelling of the instantaneous ash vs relative density relationship, theapplication of the algorithm to a data set from a mine in central Queensland was successful.

Jan 1, 1991

Naturally occurring rutile contains approximately 96 per cent titanium dioxide (Ti02), whereas the product from the ilmenite reduction - aeration upgrading process, "sub- rutile", contains only about 92 per cent Ti02. Therefore, there is an-incentive to lift the quality of sub-rutile by removing transition metal impurities, in order to supply a more valuable and marketable product, particularly for the chloride-route pigment producers. Previous studies have shown that the sub- rutile residual iron content (of approximately 4 per cent) and residual manganese content (of approximately 1.5 per cent) are chemically bound within the titanium-oxygen mineral lattice, and are most difficult to remove by simple leaching methods. In attempts to improve their eventual removal, a simple process modification has been successfully investigated in laboratory scale trials. Transition metal sulphides have been formed in the reduced ilmenite by using a "sulphur-doping" technique during reduction (metallization) conducted at controlled temperatures. These compounds give rise to greatly enhanced dissolution of the unwanted transition metal constituents during the sub- sequent aeration and acid washing steps. Thus, the manganese content of the final sulphur- doped, reduced-aerated, acid washed product can be reduced by about 90 per cent to 0.2 per cent, and the iron content by about 70 per cent to less than 1.5 per cent, in comparison with those levels remaining after unmodified pro- cessing. Additions of sulphur as low as 2 per cent of the weight of the ilmenite have proven satisfactory. Preliminary studies reveal that the modified process is economically feasible. These results suggest that the sulphur content of the Collie coal char used in an unmodified reduction step must exert some influence on the eventual removal of iron and manganese during aeration and acid washing.

Jan 1, 1973

By Harraway DH, Tanner AC

The various circuits tried!at Mount.Isa Mines during the period 1959-1963 to improve the differential%f lotation of galena and sphalerite are reported. The benefits and disadvantages of 'the various circuits are discussed. An analysis of ore charao-beris;ics.and their effect on flotation is followed by the d~soription,of a proposed".cirouit in the process of install-ation.

Jan 1, 1963

The Australian Mineral Industry has to compete on world markets, so its mineral research has to be aware of overseas developments, it must be of world class, and it must utilise as many ideas as possible in order to solve those problems that uniquely affect Australian minerals processing. North American mineral and resource research may be taken as a guide to world government, industrial, contract, and entrepreneurial research trends and ideas. A number of interesting findings are noted that may guide Australian developments and strategies for the future, in minerals research and exploitation.

Jan 1, 1986

By Mathews K. E, Willstead T. V C

Initial glory holing was followed by sublevel stoping, with a small proportion of total production mined by shrink and cut-and-fill methods.The sublevel stoping method was successfully modified to cater for altering ground conditions encountered at increasing depths. At present, 94 per cent of production comes from sublevel stopes. The evolution of this mining method and current techniques and practices is outlined. A combined shrink and,sublevel benching method was also developed to increase the mining rate of narrow orebodies over the standard stoping lift of 380 ft. Pillar recovery and stope filling operations have been continuously modified to suit the relIuirements of a rapidly developing mine.INTRODUCTIONOre production commenced at Mount Isa Mines in June 1931. Since then production has increased from approximately 2,500 tons of lead ores per mine day to the current 11,000 tons of sulphide ores per mine day comprising 3,100 tons of lead ore and 7,900 tons of copper ore. The early planners selected sublevel stoping with ring drilling for ore breaking as the most efficient and economical for Mount Isa conditions: This method satisfied requirements for:1. a low cost mining method for the comparatively low grade ores,2. a stoping sequence allowing development, stope preparation, breaking and drawing of ore to proceed concurrently,3. a method of extraction in which broken ore in the stopes would be kept to a minimum because of adverse effects of oxidation on mill metallurgy and...

Jan 1, 1961

The InLine Pressure Jig represents a breakthrough in digging technology Its design incorporates a unique combination of features previously utilised in conventional jig design. In particular, a moveable screen and circular bed are used to excellent effect. However, a major design innovation is the encapsulation of the circular bed within a vessel - allowing the equipment to operate under pressure. This innovation eliminates free water surface, improves the dynamics within the separation layer (crossflow) and provides significant cost savings in the handling of slurries. Recent research results have indicated its capacity to achieve high recoveries and upgrade ratios in the gravity separation of Minerals.

Jan 1, 1997

By R A. Pax

Operational grinding mills emit significant acoustic emissions which are a consequence of the dynamic environment prevailing inside them. From a technical perspective, the noise presents an opportunity to determine some details of the processes occurring inside the mills. The noise generated is not random and can be attributed to a range of events that occur inside these mills, consequently non-contact acoustic determinations of in-mill behaviour provide powerful insights into the operation of primary comminution tumbling mills. To enable a logically coherent picture to be formed of the processes inside a mill, arrays of microphones have been used. This approach allows a clearer picture of the in-mill behaviour of the charge to be accessed. In contrast to single microphone approaches, usually located near the expected charge toe position, an array of microphones allows much more useful information to be obtained from grinding mill noise.This paper will discuss and present data obtained from microphone arrays positioned at the toe and shoulder locations of a mill, and how this information can then be used for the optimisation of grinding mills in real-time.CITATION:Pax, R A, 2012. Determining mill operational efficiencies using non-contact acoustic emissions from microphone arrays, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 119-126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Sheard SN, Tucker DH

Sampling procedures are an important aspect of geophysical exploration survey design. It is good practice that the selection of survey parameters ensures that the signal to noise ratio is optimised, while minimising survey cost.Sampling considerations for any geophysical method include the size of the target, scale of observation, aliasing associated with station and line spacing, nature and extent of overburden, and the presentation of data.As a guide to survey design, the specifics are discussed for three geophysical techniques in common use in mineral exploration; these include the magnetic method, transient electromagnetics and induced polarisation.

Jan 1, 1976

By P Knights, M S. Kizil

Truck/shovel operations constitute 50 - 60 per cent of the cost of open pit mining operations. Mining companies, therefore, are constantly seeking to close the gap between actual truck/shovel productive capacity and maximum potential truck/shovel capacity. This paper analyses the performance of a mixed truck/shovel fleet in an open cut coal mine in Australia. It analyses operating delays, and proposes a novel graphical means of determining truck-limited or shovel-limited operations. A goal seeking algorithm is advanced in order to maximise truck/shovel match factors (MF) and hence optimise fleet productivity.

Sep 26, 2011

By Bingwen Z, Fengyi K

The hydraulic-stowing mining method is most effective for mining thick coal seams. It is superior to the sliced cover- caving and artificial mining method and the fully mechanized sublevel-caving mining method for the following reasons - a much higher recovery rate is achieved, there is much less surface subsidence and roof pressure, there is no hidden danger of gob fire, and much less methane emission and coal dust problems, etc.. However, its superiority is overshadowed by its backward stowing technique which makes mechanisation of mining and stowing difficult, causes bleed water interference to production and to the environment and is uneconomic because of the high cost of stowing material. These disadvantages limited its application to coal seams that are difficult and not suitable to be mined by other mining methods. The remedy is in reforming it thoroughly to permit mining of otherwise unminable seams and this paper presents the reformation.

Jan 1, 1992

By Moort van J C

A new low-intensity magnetic separator which operates by spinning particles in a continuously rotating magnetic field is able to reduce particle entrapment of non-magnetics to an almost insignificant level. In such separators the removal of ma

Jan 1, 1997